Electromagnetic Design of a Solid Steel Rotor Motor for Demanding Operation Environments

The solid-rotor induction motor provides a mechanically and thermally reliable solution for demanding environments where other rotor solutions are prohibited or questionable. Solid rotors, which are manufactured of single pieces of ferromagnetic material, are commonly used in motors in which the rotationspeeds exceed substantially the conventional speeds of laminated rotors with squirrel-cage. During the operation of a solid-rotor electrical machine, the rotor core forms a conductor for both the magnetic flux and the electrical current. This causes an increase in the rotor resistance and rotor leakage inductance, which essentially decreases the power factor and the efficiency of the machine. The electromagnetic problems related to the solid-rotor induction motor are mostly associated with the low performance of the rotor. Therefore, the main emphasis in this thesis is put on the solid steel rotor designs. The rotor designs studied in thisthesis are based on the fact that the rotor construction should be extremely robust and reliable to withstand the high mechanical stresses caused by the rotational velocity of the rotor. In addition, the demanding operation environment sets requirements for the applied materials because of the high temperatures and oxidizing acids, which may be present in the cooling fluid. Therefore, the solid rotors analyzed in this thesis are made of a single piece of ferromagnetic material without any additional parts, such as copper end-rings or a squirrel-cage. A pure solid rotor construction is rigid and able to keep its balance over a large speed range. It also may tolerate other environmental stresses such as corroding substances or abrasive particles. In this thesis, the main target is to improve the performance of an induction motor equipped with a solid steel rotor by traditional methods: by axial slitting of the rotor, by selecting a proper rotor core material and by coating the rotor with a high-resistive stainless ferromagnetic material. In the solid steel rotor calculation, the rotor end-effects have a significant effect on the rotor characteristics. Thus, the emphasis is also put on the comparison of different rotor endfactors. In addition, a corrective slip-dependent end-factor is proposed. The rotor designs covered in this thesis are the smooth solid rotor, the axially slitted solid rotor and the slitted rotor having a uniform ferromagnetic coating cylinder. The thesis aims at design rules for multi-megawatt machines. Typically, mega-watt-size solidrotor machines find their applications mainly in the field of electric-motor-gas-compression systems, in steam-turbine applications, and in various types of largepower pump applications, where high operational speeds are required. In this thesis, a 120 kW, 10 000 rpm solid-rotor induction motor is usedas a small-scale model for such megawatt-range solid-rotor machines. The performance of the 120 kW solid-rotor induction motors is determined by experimental measurements and finite element calculations.

Pineapple yield and fruit quality effected by NPK fertilization in a tropical soil

There is a lack of information about fertilization of pineapple grown in the State of São Paulo, Brazil. So a field experiment with pineapple 'Smooth Cayenne' was carried out to study the effects of NPK rates on yield and fruit quality. The trial was located on an Alfisol in the central part of the State of São Paulo (Agudos county). The experimental design was an incomplete NPK factorial, with 32 treatments set up in two blocks. The P was applied only at planting, at the rates of 0; 80; 160 and 320 kg/ha of P2 0(5), as superphosphate. The N and K2O rates were 0; 175; 350, and 700 kg/ha, applied as urea and potassium chloride, respectively, divided in four applications during the growth period. Response functions were adjusted to yield or to fruit characteristics in order to estimate the nutrient rates required to reach maximum values. The results showed quadratic effects of N and K on yield and a maximum of 72 t/ha of fresh fruit was attained with rates of 498 and 394 kg/ha, respectively of N and K2O. In order to reach the maximum fruit size, and to improve the percentage of first class fruit (mass greater than 2.6 kg), were necessary rates of N and K respectively 11 and 43 % higher than those for maximum yield. No effect of P rates was observed on pineapple plant growth, despite the low availability of this nutrient in the soil. The effect of N rates was negative on total soluble solids and total acidity while the opposite occurred with K, which increased also the content of vitamin C. High yield and fruit size were closely related to N and K concentrations in the leaves.

Effects of biofilm and refrigeration on acerola postharvest conservation

The objective of this work was to compare the effects of four different concentrations of cassava starch film and storage temperature on shelf life and the quality of a genotype of acerola from the Germplasm Active Bank (GAB) of Federal Rural University of Pernambuco, Brazil. Sound orange-reddish acerola fruits were washed with a chlorine solution (100 mg.L-1 active chlorine) and randomly distributed into different lots. The fruits were dipped for 3 min in a cassava starch suspension with concentrations of 1, 2, 3 and 4% (w/v) and the control without coating, stored at 10ºC (85% RH) and 22ºC (85% RH). The total soluble solids (TSS), pH, titratable acidity (TA) and ascorbic acid (AA) were determined at harvest and regular interval during storage. The use of cassava biofilm at 1% on acerola fruits maintained the highest ascorbic acid content and the temperature of 10ºC extended storage life. The fruits coated with 1 and 2% biofilm could be stored for a period up to 15 days at 10ºC, with acceptable quality characteristics.

Cyclosporine A, an alternative to the oral lichen planus erosive treatment

We present a double-blind study in two groups afflicted with oral lichen planus erythematous of long evolution and resistant to other treatments. We tested on it a treatment with Cyclosporine A (CyA) which had been successfully used before by many dermatologists. In the group A we used mouthwashes with a 5 ml Cyclosporine A solution to a 10% in olive oil of 0.4 degrees of acidity for five minutes, three times a day for eight weeks. In the control group we used acetonide of triamcinolone 01% in aqueous solution. Patients in group A improved considerably in their symptomatology in a 90% against a 60% in group B. In group A we could appreciate a disappearance of the symptomatology after two weeks of treatment in 60% of patients against 30% in group B. CyA can be an alternative to the conventional treatments in the acute period of lichen planus although it can not be considered as a first option drug because of the high cost of the treatment. For long term, results are not so good and we consider that extensive studies are necessary

Evaluation of an electronic nose to assess fruit ripeness

The main goal of our study was to see whether an artificial olfactory system can be used as a nondestructive instrument to measure fruit maturity. In order to make an objective comparison, samples measured with our electronic nose prototype were later characterized using fruit quality techniques. The cultivars chosen for the study were peaches, nectarines, apples, and pears. With peaches and nectarines, a PCA analysis on the electronic nose measurements helped to guess optimal harvest dates that were in good agreement with the ones obtained with fruit quality techniques. A good correlation between sensor signals and some fruit quality indicators was also found. With pears, the study addressed the possibility of classifying samples regarding their ripeness state after different cold storage and shelf-life periods. A PCA analysis showed good separation between samples measured after a shelf-life period of seven days and samples with four or less days. Finally, the electronic nose monitored the shelf-life ripening of apples. A good correlation between electronic nose signals and firmness, starch index, and acidity parameters was found. These results prove that electronic noses have the potential of becoming a reliable instrument to assess fruit ripeness.

Maturity indexes for 'Kumagai' and 'Paluma' guavas

Harvest time is one of the main factors related to guava fruit postharvest losses. It is subjectively determined by fruit size and skin color, without any consensual standardization among the growers. The use of maturity indexes enables growers to know the ideal harvest time according to each market situation. The objective of this work was to determine the maturity indexes to identify the harvest time for guava fruit cv. Kumagai and Paluma. Skin color, fruit firmness, soluble solids, titratable acidity, ratio and ascorbic acid were analyzed. The most adequate maturity indexes for 'Kumagai' guava fruit were skin color and pulp firmness, while for 'Paluma' guava fruit, the best indexes were skin color, pulp firmness, titratable acidity and ratio.

Physical and chemical characterization of yellow mangosteen fruits

The work had as objective the physico-chemical characterization of yellow mangosteen fruits. Six samples of 25 fruits were harvested in yellow mangosteen plants of the Active Germoplasm Bank of São Paulo State University and characterized by evaluation of length and width, weight, percentage and number of seeds per fruit, peel and pulp percentage, soluble solid (SS), titratable acidity (TA), vitamin C and SS/TA rate. Yellow mangosteen fruit is an intermediate vitamin C source with an average content 120.33 mg/100g of fresh fruit and has good technological quality.

Estimates of genetic parameters for fruit yield and quality in custard apple progenies

Apparently, there are no custard apple cultivars defined for the northeastern region of Brazil. The establishment of breeding programs aimed at the selection of types from productive locations for later cloning is desirable. This work's objective was to evaluate the yield (during the first three crops) and quality (first crop) of fruits from 20 half-sibling custard apple tree progenies, selected from home orchards. An additional objective was to estimate genetic parameters for the traits evaluated. A micro sprinkling-irrigated experiment was conducted in Mossoró-RN, Brazil, as random blocks with five replications. In characteristics evaluated for periods longer than a year (diameter, height and mean weight of fruits, number of fruits ha-1 and fruit yield (kg ha-1), and a split-plot design was adopted, with progenies considered as plots and annual cropping seasons as subplots. The best progenies in terms of fruit yield (A3 and A4) are not necessarily the best for fruit dimensions and fruit mean weight (A2, FE4, JG1, JG2, SM1, SM7, and SM8). These progenies show great potential to be used in future studies on crosses or on vegetative propagation. In this regard, progeny JG2 should be highlighted as promising in terms of yield and fruit size. The progenies are not different with regard to percentages (in relation to mean fruit mass) of pericarp, endocarp, seeds, and receptacle, in the fruit, and fruit volume, number of seeds/fruit, and total soluble solids content in the fruit pulp, but progeny FE4 presents higher total titratable acidity in the fruit pulp. Narrow-sense heritability estimates were relatively high for all characteristics in which there was variability between progenies, with higher values for number of fruits ha-1 (80 %) and fruit yield (78 %). Relatively high coefficients of genotypic variation (around 20%) were observed for number of fruits ha-1 and fruit yield, with lower values for the other characteristics. There were positive genotypic and phenotypic correlations between fruit diameter (FD) and fruit height, FD and mean fruit weight, and number of fruits ha-1 and fruit yield.

Analysis of vineyard differential management zones and relation to vine development, grape maturity and quality

The objective of research was to analyse the potential of Normalized Difference Vegetation Index (NDVI) maps from satellite images, yield maps and grapevine fertility and load variables to delineate zones with different wine grape properties for selective harvesting. Two vineyard blocks located in NE Spain (Cabernet Sauvignon and Syrah) were analysed. The NDVI was computed from a Quickbird-2 multi-spectral image at veraison (July 2005). Yield data was acquired by means of a yield monitor during September 2005. Other variables, such as the number of buds, number of shoots, number of wine grape clusters and weight of 100 berries were sampled in a 10 rows × 5 vines pattern and used as input variables, in combination with the NDVI, to define the clusters as alternative to yield maps. Two days prior to the harvesting, grape samples were taken. The analysed variables were probable alcoholic degree, pH of the juice, total acidity, total phenolics, colour, anthocyanins and tannins. The input variables, alone or in combination, were clustered (2 and 3 Clusters) by using the ISODATA algorithm, and an analysis of variance and a multiple rang test were performed. The results show that the zones derived from the NDVI maps are more effective to differentiate grape maturity and quality variables than the zones derived from the yield maps. The inclusion of other grapevine fertility and load variables did not improve the results.

Determination of thermal diffusivity in papaya pulp as a function of maturation stage

In order to determine the penetration of the thermal wave in the papaya fruit pulp (Carica papaya L.), cv. Golden, thermal diffusivity of the pulp was obtained measuring temperature at four different depths. Measurements were carried out initially with the fruit on the first stage of maturity. The changes of the thermal diffusivity were expressed as a function of ripening. A temporal decrease of the thermal diffusivity was observed. Chemical (pH, soluble solids and total titratable acidity) and physical (pulp firmness) properties were measured as well and the results were compared to the thermal diffusivity change.

Protocolo para la zonificación intraparcelaria de la viña para vendimia selectiva a partir de imágenes multiespectratrales

En este trabajo se presenta un protocolo para la zonificación intraparcelaria de la viña con la finalidad de vendimia selectiva. Se basa en la adquisición de una imagen multiespectral detallada en el momento del envero, a partir de la cual se obtiene el índice de vegetación de la diferencia normalizada (NDVI). Este índice se clasifica en áreas de vigor alto y bajo mediante un proceso de clasificación no supervisada (algoritmo ISODATA). Las zonas resultantes se generalizan y se transfieren al monitor de cosecha de una máquina vendimiadora para realizar la recolección selectiva. La uva recolectada según este protocolo en parcelas control ha mostrado diferenciación en cuanto a parámetros de calidad como el pH, la acidez total, el contenido de polifenoles y el color. La imagen multiespectral utilizada fue adquirida por el satélite Quickbird-2. Los datos de calidad de la uva fueron muestreados según una malla regular de 5 filas por 10 cepas, procediendo a un test estadístico de rangos múltiples para analizar la separación de medias de las variables analizadas en cada zona de NDVI.

Preharvest calcium sprays were not always needed to improve quality of 'gala' apples in Brazil

Calcium sprays have normally improved both the quality and the storage life of apples throughout the world because Ca helps to prevent many fruit disorders and that taken up from the soil does not often reach the fruit in adequate amounts. Since the efficacy of Ca sprays varies according to soil, apple cultivar, and weather conditions, this study was carried out from 1998 to 2004, in the Southern of Brazil, in order to assess the effect of Ca sprays on the quality and storability of 'Gala' fruits. The experiment was set up in an orchard planted in 1988, on a density of 1234 trees/ha. Treatments consisted of 0, 4, 8, and 12 annual sprays of 0.5% CaCl2 regularly distributed 30 days after petal fall until one week before harvest. Fruits of the same size and maturity level were annually analyzed at harvest and after five months of conventional cold storage (-1ºC and 90-95% of RH). In five out of six seasons, fruits from all treatments were free of any physiological disorder, and Ca sprays had no effect on leaf composition and on any fruit attribute (soluble solids, titratable acidity, starch pattern index, flesh firmness, and concentrations of N, K, Ca and Mg). In the season of 2000/2001, however, when yield was 18 t ha-1 and fruits had an average weight of 175 g, the incidence of bitter pit plus lenticel blotch pit on stored fruits was 24% in the treatment with no calcium sprays and it decreased up to 2% in that with 12 sprays. Two seasons later, yield was also low (25 t ha-1) and fruits were large (168 g each), but they did not show any physiological disorder regardless of the number of Ca sprays. It seems that the incidence of Ca related disorders in 'Gala' apples grown on limed soils in Brazil with no excess of any nutrient only occurs on seasons with low crop yield, as a result of large fruits and a high leaf/fruit ratio, associated with some unknown environmental conditions.

Addition of nitrogen had no effect on yield and quality of apples in an high density orchard carrying a dwarf rootstock

The effect of N addition on apple yield and quality may vary according to the tree vigor. Apple trees developed over vigorous rootstocks had shown no response to N application in Brazil. In this study it was evaluated the effect of N addition to the soil on yield and quality of ´Royal Gala´ apples grafted on a dwarf rootstock (M.9). The orchard was planted in 1995 (2,857 trees ha-1) on an Oxisol containing 40 g kg-1 of organic matter and pH 6.0. The experiment was carried out from 1998 up to 2005. Treatments consisted of rates of N (0, 50, 100 and 150 kg ha-1 year-1 from 1998 to 2001, and respectively 0, 100, 200 and 300 kg ha-1 afterwards), all broadcasted within the tree row in two equal splits, at bud break and after harvest, as ammonium sulfate. Addition of N to the soil had no effect on fruit yield over the six years regardless of the applied rate. Averaged across treatments and years, fruit yield was 52.3 t ha-1. Nitrogen in the leaves (average of 24 g kg-1) or in the fruits (average of 346 mg kg-1) as well as some attributes related to fruit quality (color, firmness, acidity, soluble solids, physiological disorders) were unaffected by N addition. Some plant parameters related to tree vigor, however, grew higher with the increase on N rate. Thus, it is not necessary to apply N to deep Brazilian soils containing high organic matter in order to assure good fruit quality and yield on high-density orchards carrying dwarf rootstocks probably because the N required for tree growth and fruit production is supplied from soil organic matter decay.

Enzymatic technology to improve oil extraction from Caryocar brasiliense camb. (Pequi) Pulp.

The present study aims to compare yield and quality of pequi pulp oil when applying two distinct processes: in the first, pulp drying in a tray dryer at 60ºC was combined with enzymatic treatment and pressing to oil extraction; in the second, a simple process was carried out by combining sun-drying pulp and pressing. In this study, raw pequi fruits were collected in Mato Grosso State, Brazil. The fruits were autoclaved at 121ºC and stored under refrigeration. An enzymatic extract with pectinase and CMCase activities was used for hydrolysis of pequi pulp, prior to oil extraction. The oil extractions were carried out by hydraulic pressing, with or without enzymatic incubation. The oil content in the pequi pulp (45% w/w) and the physicochemical characteristic of the oil was determined according to standard analytical methods. Free fatty acids, peroxide values, iodine and saponification indices were respectively 1.46 mgKOH/g, 2.98 meq/kg, 49.13 and 189.40. The acidity and peroxide values were lower than the obtained values in commercial oil samples, respectively 2.48 mgKOH/g and 5.22 meq/kg. Aqueous extraction has presented lower efficiency and higher oxidation of unsaturated fatty acids. On the other hand, pequi pulp pressing at room temperature has produced better quality oil. However its efficiency is still smaller than the combined enzymatic treatment and pressing process. This combined process promotes cellular wall hydrolysis and pulp viscosity reduction, contributing to at least 20% of oil yield increase by pressing.

Effect of prestorage curing on storage life, internal and external qualities of sweet orange (Citrus sinensis)

Orange fruits from two seasons, in April and August 2006 representing late 2005 and early 2006 harvests respectively were cured in hot air at 36-37(0)C to 1%, 3%, 5% and 7% weight loss before storage at 28(0)C and 86% relative humidity (RH). The fruits were observed for incidence of decay, further weight loss, juice content, firmness or softening of the peel, total soluble solids (TSS), pH, titratable acidity, and colour during storage. Curing reduced the incidence of decay. All control fruits were rotten by day 21 in August harvest while 22.5% of the control was rotten by day 56 in the April harvest. Storage life was extended beyond 56 days in fruits cured with 1, 3, 5 and 7% in April harvest as there was no decay throughout, while decay incidence in August harvest was 88.9, 61.1, 22.2 and 31.3% in 1, 3, 5 and 7% respectively. Penicillium digitatum, Phytophthora sp., Alternaria citri and Collectotrichum gloeosporioides were among decay causing moulds detected. Control fruits lost more weight during storage than cured fruits did. Fruit rind hardening was more noticed in the control and those cured to 1% weight loss, especially from the April harvest. It was insignificant in other treatments in both trials. Titratable acidity, pH, juice content and TSS were not affected by the treatment. Colour change to yellow was however retarded by curing. Curing to 5% weight loss was best for decay control and quality retention.