Evaluation of Estrogenic Potential of Flavonoids Using a Recombinant Yeast Strain and MCF7/BUS Cell Proliferation Assay

Phytoestrogens are of interest because of their reported beneficial effects on many human maladies including cancer, neurodegeneration, cardiovascular disease and diabetes. Furthermore, there is a search for compounds with estrogenic activity that can replace estrogen in hormone replacement therapy during menopause, without the undesirable effects of estrogen, such as the elevation of breast cancer occurrence. Thus, the principal objective of this study was to assess the estrogenic activity of flavonoids with different hydroxylation patterns: quercetin, kaempferol, luteolin, fisetin, chrysin, galangin, flavone, 3-hydroxyflavone, 5-hydroxyflavone and 7-hydroxyflavone via two different in vitro assays, the recombinant yeast assay (RYA) and the MCF-7 proliferation assay (E-screen), since the most potent phytoestrogens are members of the flavonoid family. In these assays, kaempferol was the only compound that showed ERα-dependent transcriptional activation activity by RYA, showing 6.74±1.7 nM EEQ, besides acting as a full agonist for the stimulation of proliferation of MCF-7/BUS cells. The other compounds did not show detectable levels of interaction with ER under the conditions used in the RYA. However, in the E-screen assay, compounds such as galangin, luteolin and fisetin also stimulated the proliferation of MCF-7/BUS cells, acting as partial agonists. In the evaluation of antiestrogenicity, the compounds quercetin, chrysin and 3-hydroxyflavone significantly inhibited the cell proliferation induced by 17-β-estradiol in the E-screen assay, indicating that these compounds may act as estrogen receptor antagonists. Overall, it became clear in the assay results that the estrogenic activity of flavonoids was affected by small structural differences such as the number of hydroxyl groups, especially those on the B ring of the flavonoid. © 2013 Resende et al.

Characterization of the acute inflammatory response in the hybrid tambacu (Piaractus mesopotamicus male × Colossoma macropomum female) (Osteichthyes)

Este estudo avaliou a resposta inflamatória aguda induzida por injeções de 0,5 mL de solução salina (controle), 500 µg de carragenina e 0,5 mL de tioglicolato a 3% na bexiga natatória de juvenis do híbrido tambacu. Os peixes foram distribuídos em três tratamentos, três repetições e aclimatados durante 10 dias antes do ensaio. A caracterização das células do exsudato inflamatório foi feita após coloração com Giemsa e PAS. Peixes injetados com carragenina apresentaram maior número de células no exsudato inflamatório do que com salina e tioglicolato. A porcentagem de trombócitos no exsudato foi maior nos injetados com carragenina quando comparada com a dos injetados com tioglicolato. Por outro lado, o percentual de granulócitos foi maior em animais injetados com tioglicolato do que em animais injetados com carragenina. A carragenina provocou maior migração de macrófagos para o foco inflamatório. O método de PAS confirmou a presença de três tipos de granulócitos: célula granular eosinofílica (CGE) tipo 1 com as características da célula granulocítica especial encontrada no sangue, CGE tipo 2, menor do que esta última, e de neutrófilos. Este estudo contribui para o melhor entendimento da resposta inflamatória e dos processos infecciosos em peixes nativos.

Parasitic infections of Piaractus mesopotamicus and hybrid (P. mesopotamicus x Piaractus brachypomus) cultured in Brazil

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Bulk plasmon polariton-gap soliton-induced transparency in one-dimensional Kerr-metamaterial superlattices

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Brewer's yeast and sugarcane yeast as protein sources for dogs

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Effect of Er:YAG laser and diamond drill on hybrid layer morphology obtained with self-etch adhesive: analysis by SEM and confocal laser scanning microscopy (CLSM)

This study aimed to evaluate the effect of Er:YAG (L) and diamond drills (DD) on: 1) the microshear bond strength (MPa); 2) the adhesive interface of two-step (TS) – Adper Scotchbond Multipurpose and one-step (OS) adhesives – Adper EasyOne, both from 3M ESPE. Material and methods: According to the preparation condition and adhesives, the samples were divided into four groups: DD_TS (control); DD_OS; L_TS and L_OS. 60 bovine incisors were randomly divided into experimental and groups: 40 for microshear bond strength (n = 10) and 20 for the adhesive interface morphology [6 to measure the thickness of the hybrid layer (HL) and length of tags (t) by CLSM (n = 3); 12 to the adhesive interface morphology by SEM (n = 3) and 2 to illustrate the effect of the instruments on dentine by SEM (n = 1)]. To conduct the microshear bond strength test, four cylinders (0.7 mm in diameter and 1 mm in height with area of adhesion of 0.38 mm) were constructed with resin composite (Filtek Z350 XT – 3M ESPE) on each dentin surface treated by either L or DD and after adhesives application. Microshear bond strength was performed in universal testing machine (EMIC 2000) with load cell of 500 kgf and a crosshead speed of 0.5 mm / min. Adhesive interface was characterized by thickness of hybrid layer (HL) and length of tags (t) in nm, with the aid of UTHSCSA ImageTool software. Results: Microshear bond strength values were: L_TS 34.10 ± 19.07, DD_TS 24.26 ± 9.35, L_OS 33.18 ± 12.46, DD_OS 21.24 ± 13.96. Two-way ANOVA resulted in statistically significant differences only for instruments (p = 0.047). Mann-Whitney identified the instruments which determined significant differences for HL thickness and tag length (t). Concerning to the adhesive types, these differences were only observed for (t). Conclusion: It can be concluded that 1) laser Er:YAG results in higher microshear bond strength values regardless of the adhesive system (TS and OS); 2) the tags did not significant affect the microshear bond strength; 3) the adhesive interface was affected by both the instruments for cavity preparation and the type of adhesive system used.

Can an LED-laser hybrid light help to decrease hydrogen peroxide concentration while maintaining effectiveness in teeth bleaching?

The aim of this study was to compare the bleaching efficacy of 35% hydrogen peroxide and 15% hydrogen peroxide with nitrogen-doped titanium dioxide catalysed by an LED-laser hybrid light. We studied 70 patients randomized to two groups. Tooth shade and pulpal sensitivity were registered. Group 1: 15% hydrogen peroxide with nitrogen-doped titanium dioxide. Group 2: 35% hydrogen peroxide. Both groups were activated by an LED-laser light. No significant differences were seen in shade change immediately, one week or one month after treatment (p > 0.05). Differences were seen in pulpal sensitivity (p < 0.05). The use of an LED-laser hybrid light to activate 15% hydrogen peroxide gel with N_TiO2 permits decreasing the peroxide concentration with similar aesthetic results and less pulpal sensitivity than using 35% hydrogen peroxide for bleaching teeth.

Effect of partially demineralized dentin beneath the hybrid layer on dentin-adhesive interface micromechanics

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Recovery Tests of an Hybrid Current Limiter Composed of a SFCL in Parallel to an Air-Core Power Reactor

The resistive-type superconducting fault current limiters (RSFCL) prototypes using YBCO-coated conductors have shown current limitation for medium voltage class applications for acting time up to 80 ms. By connecting an air-core reactor in parallel with the RSFCL, thus making an hybrid current limiter, one can extend the acting time for up to 1 s. In this work, we report the performance of a hybrid current limiter subjected to an AC peak fault current of 2 kA during 1 s for which within the first 80 ms the SFCL limits the current concurrently with the air-core reactor, and for the remaining 920 ms, only the air-core reactor limits the current. In order to evaluate the actual conditions for subsequent reconnection of RSFCL to the power grid, the hybrid fault current limiter was tested varying the time interval for recovery from 900 ms and 1.2 s, followed again by the concurrent operation of the hybrid limiter during 1 s (SFCL during 80 ms). From this evaluation test, the recovery time can be measured and compared using the voltage peak generated in superconducting module from the first and second fault test. The recovery time was also determined through the pulsed current method (PCM) on short-length sample test. The results showed that the fault current was limited from 1.9 kA down to 514 A after 1 cycle of 60 Hz frequency, with recovery time lower than 1.2 s for two subsequent fault current tests.

A hybrid method for the probabilistic maximal covering location-allocation problem

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Energetic exploitation from a hybrid PV-wind power micro-generation rural electrification

Hybrid system micro-generation integration of PV-wind power is presented by a form of energy in which problems resulting from variability in the intensity of wind and solar intensity are possible mitigation either by complementation between one source to another or the largest stability configured by the generate the system. Based on this context, this work aims to assessing the performance of a hybrid system PV-wind power energy small of a rural property for their electrification. The study has been developed at the Rural Laboratory Powering from Engineering Department of UNESP. In order to present this research, a hybrid system has been installed PV-wind power, composed of one 400Wp windmill and a 300 Wp PV-system. The results obtained allowed us to evaluate the solar and wind energy supplied ranked among 285 and 360 kWh electric power generated by the PV-wind power hybrid system stood between 25,5 and 31 kWh. At is to say achieving yield of approximately than 10% during one year observation period, i.e., it was concluded that the performance of the hybrid system depended essentially the energy received and generated by the PV-system and that there was complementation between generating wind power and PV-systems with regard to time of day and the annual seasons by confirming the technical feasibility of this kind system of micro-generation in small rural properties.

Yamadazyma riverae sp. nov., a yeast species isolated from plant materials

Nine strains of a novel yeast species were isolated from rotting wood, tree bark, ant nests or living as endophytes in leaves of Vellozia gigantea. Analysis of the sequences of the internal transcribed spacer (ITS) region and the D1/D2 domains of the large subunit rRNA gene showed that this species is related to Candida insectorum in the Yamadazyma clade. The new species differs from its closely related species by 10 and 11 substitutions in the ITS region and the D1/D2 domains of the large subunit of the rRNA gene, respectively. The species is heterothallic and forms asci with one to two hat-shaped ascospores. The name Yamadazyma riverae sp. nov. is proposed. The type strain of Yamadazyma riverae sp. nov. is UFMG-CM-Y444T (= CBS 14121) and the allotype strain is TT12 (= CBS 14098 = UFMG-CM-Y577). The Mycobank number is MB 813221.

Photodynamic inactivation of a multispecies biofilm using Photodithazine(®) and LED light after one and three successive applications

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Xenia Effects on Quality of Maize Female Inbred in Production of Hybrid Seeds

In Maize (Zea maize L.), cost of hybrid seed production is directly related to the yield and quality of seed obtained per hectare of female parent. It is also important to consider the effects that a male parent can exert on the development of hybrid seed in the female parent. This effect is known as xenia. The objectives of this study were to evaluate xenia effects on 1) yield as 80K units, 2) germination of the hybrid seed and 3) susceptibility of the hybrid seed to mechanical damage. One female inbred and four male inbred lines were selected from a parent list of hybrids. The experiment was designed to allow individual cross pollination between each male inbred and the female inbred line. For use as a control, the female inbred was allowed to self pollinate. Experiments were conducted in Illinois and Iowa during 2008 and 2009 and in Nebraska during 2009. A significant inbred effect was detected on yield as 80k (α=0.001). The selfed female and pollination with male inbred B resulted in lower yields of hybrid seed. For germination, a significant inbred effect was detected (α=0.001), but was due to lower germination percentage of seed produced on the selfed female. All hybrid combinations resulted in higher germination percentages with no significant differences among hybrids. The inbred x mechanical damage interaction was significant (P=0.04) for effects on cold saturated soil germination tests. Use of inbred B resulted in a two-percentage-point reduction in cold germination when treated with the impact simulator. In a maize seed company, the production research group provides yield estimates for production of new hybrid combinations. Results from this study indicate that using only the female inbred yield may provide inaccurate estimates. Therefore to improve yield estimation, experiments should be designed to include male inbreds. Male inbreds can also impart a negative effect to the hybrid seed on tolerance to mechanical damage, thus lowering quality and increasing seed discard. When testing for hybrid seed germination, there is no need to consider distinct hybrid combinations. Female inbreds can be grown in open-pollinated fields to avoid loss of vigor observed with selfing. Advisor: George Graef

Disulfide Biochemistry in 2-Cys Peroxiredoxin: Requirement of Glu50 and Arg146 for the Reduction of Yeast Tsa1 by Thioredoxin

2-Cys peroxiredoxin (Prx) enzymes are ubiquitously distributed peroxidases that make use of a peroxidatic cysteine (Cys(P)) to decompose hydroperoxides. A disulfide bond is generated as a consequence of the partial unfolding of the alpha-helix that contains Cys(P). Therefore, during its catalytic cycle, 2-Cys Prx alternates between two states, locally unfolded and fully folded. Tsa1 (thiol-specific antioxidant protein 1 from yeast) is by far the most abundant Cys-based peroxidase in Saccharomyces cerevisiae. In this work, we present the crystallographic structure at 2.8 angstrom resolution of Tsa1(C47S) in the decameric form [(alpha(2))(5)] with a DTT molecule bound to the active site, representing one of the few available reports of a 2-Cys Prx (AhpC-Prx1 subfamily) (AhpC, alkyl hydroperoxide reductase subunit C) structure that incorporates a ligand. The analysis of the Tsa1(C47S) structure indicated that G1u50 and Arg146 participate in the stabilization of the Cys(P) alpha-helix. As a consequence, we raised the hypothesis that G1u50 and Arg146 might be relevant to the Cys(P) reactivity. Therefore, Tsa1(E50A) and Tsa1(R146Q) mutants were generated and were still able to decompose hydrogen peroxide, presenting a second-order rate constant in the range of 10(6) M-1 S-1. Remarkably, although Tsa1(E50A) and Tsa1(R146Q) were efficiently reduced by the low-molecular-weight reductant DTT, these mutants displayed only marginal thioredoxin (Trx)-dependent peroxidase activity, indicating that G1u50 and Arg146 are important for the Tsa1-Trx interaction. These results may impact the comprehension of downstream events of signaling pathways that are triggered by the oxidation of critical Cys residues, such as Trx. (C) 2012 Elsevier Ltd. All rights reserved.