Fluid dynamics of air in a packed bed: velocity profiles and the continuum model assumption

Air flow through packed beds was analyzed experimentally under conditions ranging from those that reinforce the effect of the wall on the void fraction to those that minimize it. The packing was spherical particles, with a tube-to-particle diameter ratio (D/dp) between 3 and 60. Air flow rates were maintained between 1.3 and 4.44 m3/min, and gas velocity was measured with a Pitot tube positioned above the bed exit. Measurements were made at various radial and angular coordinate values, allowing the distribution of air flow across the bed to be described in detail. Comparison of the experimentally observed radial profiles with those derived from published equations revealed that at high D/dp ratios the measured and calculated velocity profiles behaved similarly. At low ratios, oscillations in the velocity profiles agreed with those in the voidage profiles, signifying that treating the porous medium as a continuum medium is questionable in these cases.

Nanostructure and properties of ZnO films produced by the pyrosol process

Indium doped ZnO films were deposited by the pyrosol process on glass substrates at different temperatures from solutions containing In/Zn molar ratios up to 10%. The nanostructure of the films was investigated using grazing-incidence small angle X-ray scattering (GISAXS). The mass density was determined by X-ray reflectivity and the composition by X-ray photoelectron spectroscopy. The GISAXS measurements revealed an anisotropic pattern for films deposited at 573 and 623 K and a isotropic one for those deposited at higher temperatures. The anisotropic patterns indicate the presence of elongated nanopores with their long axes perpendicular to the film surface. In contrast, the isotropic nature of GISAXS patterns of films grown at high temperatures (673 and 723 K) suggests the presence of spherical voids. The pore size distribution function determined from the isotropic patterns indicates a multimodal size distribution. on the other hand, the measured mass density of the doped films with isotropic nanotexture is higher than that of the anisotropic films while the electric resistivity is significantly lower. This is in agreement with the detected strong reduction of the void density and specific surface area at approximately constant pore size.

High hydrostatic pressure processing on microstructure of probiotic low-fat yogurt

The effect of milk processing on the microstructure of probiotic low-fat yogurt was studied. Skim milk fortified with skim milk powder was subjected to three treatments prior to innoculation: thermal treatment at 85 degrees C for 30 min, high hydrostatic pressure at 676 MPa for 5 min, and combined treatments of high hydrostatic pressure (HHP) and heat. The processed milk was then fermented by using two different starter cultures containing Streptococcus thermophilus, Lactobacillus delbrueckii ssp. bulgaricus, Lactobacillus acidophilus, and Bifidobacterium longum. The microstructure of heat-treated milk yogurt had fewer interconnected chains of irregularly shaped casein micelles, forming a network that enclosed the void spaces. on the other hand, microstructure of HHP yogurt had more interconnected clusters of densely aggregated protein of reduced particle size, with an appearance more spherical in shape, exhibiting a smoother more regular surface and presenting more uniform size distribution. The combined HHP and heat milk treatments led to compact yogurt gels with increasingly larger casein micelle clusters interspaced by void spaces, and exhibited a high degree of cross-linking. The rounded micelles tended to fuse and form small irregular aggregates in association with clumps of dense amorphous material, which resulted in improved gel texture and viscosity. (C) 2007 Elsevier Ltd. All rights reserved.

The dimension of the pore space in sponges

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Electrode poling of cellular polypropylene films with short high-voltage pulses

Recently, piezoelectric cellular polypropylene (PP) was proposed as a new type of quasi-ferroelectric. The observed hysteresis of the charge density as a function of the electric field could be explained as field-dependent charging inside the gas-filled voids. Interestingly enough, the measurable poling behavior of the macroscopic dipoles formed by charges that are trapped at the internal void surfaces is phenomenologically completely identical to the cooperative poling behavior of microscopic molecular dipoles in ferroelectric polymers. Therefore, it can be assumed that charge separation (or charge redistribution) and subsequent trapping in cellular PP is a rather fast switching process. In order to examine the poling dynamics, we developed an experimental setup for pulsed poling. High-voltage pulses with a duration of 45 μs (FWHM) were applied in direct contact to two-side metallized cellular PP films. The pulsed poling yields piezoelectricity in the cellular PP. We study and discuss the dependence of the resulting piezoelectricity on the poling field. We also characterize the charge separation during application of higher electric poling fields of up to -10 kV in direct contact to the two-side metallized films for longer times.

Template-based fluoropolymer ferroelectrets with multiple layers of tubular channels

Significant efforts are devoted to developing new ferroelectrets with well-controlled void distributions or uniform voids and with good long-term and thermal stability of the piezoelectricity. Here, we describe the concept, the fabrication, and the most relevant properties of fluoropolymer ferroelectret systems with three separate films of fluoroethylenepropylene (FEP), alternating with two polytetrafluoroethylene (PTFE) templates. The FEP films are selectively fused by means of a lamination process. Two practically identical PTFE templates are used, which have parallel rectangular openings (1.5×30 mm 2) separated by PTFE ridges of 1.5 mm width. After removing the PTFE templates, a three-layer FEP-film sandwich with tubular channels is obtained. We demonstrate that such FEP-film systems exhibit significant and stable piezoelectricity after charging under a high DC voltage. The resulting piezoelectric effect may be further improved by carefully assembling and arranging the PTFE templates during preparation. ©2010 IEEE.

Questões preliminares sobre aspectos do vazio na arte contemporânea

Pós-graduação em Artes - IA

Simulação computacional do escoamento bifásico com formação de espuma da mistura óleo-refrigerante R134a ao longo de um tubo reto de seção circular constante

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Os professores de matemática e as ações educacionais públicas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

A dramatização da crise dos valores sociais e humanos em Tess of the d'Urbervilles, de Thomas Hardy

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da salinidade do fluido na avaliação da compactação e da resistividade elétrica de dois solos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Rios e terras: história ambiental de Goiás (1822-1850)

Pós-graduação em História - FCLAS

O sentimento de vazio: reflexões psicanalíticas na atualidade

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modernidade e integração na Amazônia: "intelligentsia" e "broadcasting" no entre guerras, 1923 -1937

Modernidade e integração na região chamada Amazônia, vez ou outra, sempre ouvimos na mídia, nos meios intelectuais, entre políticos das mais variadas tendências, do Norte e de outras regiões do país, e surgem questionamentos sobre qual o melhor caminho para a Amazônia. Projetos e ideologias foram criados, normalmente girando em torno das possibilidades de modernidade e integração para a região, há muito considerada reserva de lendas e minérios, o reino da floresta e da "planície", espaço isolado, distante, verdadeiro "vazio" de "éden tropical" ou "inferno verde". Desde os embates na Colônia e no Império sobre integrar ou separar do poder central até aos grandes projetos nos anos de 1970, a intelligentsia local e os meios de comunicação manifestaram ponto de vistas e assumiram, em muitos casos, posicionamentos políticos, principalmente a partir dos séculos XIX e XX. Tentei entrar um pouco nesse debate, reportando-me às primeiras décadas do século XX, e encontrando nesse passado, personagens que espelham os novos atores do presente: os intelectuais e o meio de comunicação mais moderno do entre guerras, ao lado do cinema, o rádio.

Caracterização da liga 6101 refinada com a adição de diferentes teores de cobre e solidificadas em molde unidirecional horizontal e em molde "U"

A liga 6101 (série 6xxx) foi modificada através da adição de cobre nos percentuais de 0,05%Cu e 0,3%Cu, e também de refinadores de grão à base de uma pré-liga Al-Ti-B. As ligas foram caracterizadas termicamente (coeficiente de transferência de calor metal/molde, Velocidade de deslocamento da isoterma liquidus e taxa de resfriamento), mecanicamente (limite de resistência à tração e módulo de tenacidade) e eletricamente (resistência, resistividade e condutividade elétrica) utilizando duas formas de vazamentos: uma sendo através de solidificação em molde unidirecional horizontal e a outra através do molde em “U”. Para a solidificação em molde unidirecional horizontal as caracterizações mostraram-se bastante influenciadas pelos refinadores de grão e pela viscosidade que o cobre exerce na eficiência do contato metal/molde das ligas, alterando significativamente suas propriedades térmicas, mecânicas e elétricas. Por outro lado, na solidificação em molde “U” as ligas foram avaliadas apenas através de caracterização mecânica e elétrica, tendo em vista a preocupação sobre as variáveis do processo de conformação da liga metálica, tais como, a avaliação da taxa de deformação, do limite de resistência a tração, da tenacidade e da resistência, resistividade e condutividade elétrica, do perfil metálico produzido, para corpos de prova de diferentes diâmetros. Para o molde em “U” houve ainda a adição e avaliação de mais duas ligas sendo a Al-0,6Mg-0,4Si-0,1Cu e Al-0,6Mg-0,4Si-0,2Cu. As propriedades mecânicas e elétricas sofreram forte influência do encruamento, do teor de cobre e das microcavidades existentes nas estruturas das ligas.