Nonlinear and linear autopilot performance comparison of tactical flight vehicle

n this paper, three-axis autopilot of a tactical flight vehicle has been designed for surface to air application. Both nonlinear and linear design synthesis and analysis have been carried out pertaining to present flight vehicle. Lateral autopilot performance has been compared by tracking lateral acceleration components along yaw and pitch plane at higher angles of attack in presence of side force and aerodynamic nonlinearity. The nonlinear lateral autopilot design is based on dynamic inversion and time scale separation principle. The linear lateral autopilot design is based on three-loop topology. Roll autopilot robustness performance has been enhanced against unmodeled roll disturbances by backstepping technique. Complete performance comparison results of both nonlinear and linear controller based on six degrees of freedom simulation along with stability and robustness studies with respect to plant parameter variation have been discussed in the paper.

Experiments and analysis of propagation front under gasification regimes in a packed bed

The paper analyses the results of experiments on the propagation rate in a fuel bed under gasification conditions in a co-current reactor configuration. Experiments using wood chips with different values of moisture content have been conducted under gasification conditions. The influence of air mass flux on the propagation rate, peak temperature and gas quality is investigated. It is observed from the experiments that the flame front propagation rate initially increases as the air mass flux increased, reaching a peak propagation rate, and further increase in the air mass flux results in a decrease in the propagation rate. However, the bed movement increases with the increase in air mass flux. The experimental results provide an understanding on influence of the fuel properties on propagation front. The surface area per unit volume of the particles in the packed bed plays an important role in the propagation rate. It has been argued that the flaming pyrolysis contributes towards the flame propagation as opposed to the overall combustion process in a packed bed. The calorific value of the producer gas generated is nearly the same over the entire range of air mass flux for bone-dry and 10% moist wood. (C) 2014 Elsevier B.V. All rights reserved.

Curvature-constrained trajectory generation for waypoint following for miniature air vehicle

This paper addresses trajectory generation problem of a fixed-wing miniature air vehicle, constrained by bounded turn rate, to follow a given sequence of waypoints. An extremal path, named as g-trajectory, that transitions between two consecutive waypoint segments (obtained by joining two waypoints in sequence) in a time-optimal fashion is obtained. This algorithm is also used to track the maximum portion of waypoint segments with the desired shortest distance between the trajectory and the associated waypoint. Subsequently, the proposed trajectory is compared with the existing transition trajectory in the literature to show better performance in several aspects. Another optimal path, named as loop trajectory, is developed for the purpose of tracking the waypoints as well as the entire waypoint segments. This paper also proposes algorithms to generate trajectories in the presence of steady wind to meet the same objective as that of no-wind case. Due to low computational burden and simplicity in the design procedure, these trajectory generation approaches are implementable in real time for miniature air vehicles.

Rollover-Preventive Force Synthesis at Active Suspensions in a Vehicle Performing a Severe Maneuver With Wheels Lifted Off

Among the intelligent safety technologies for road vehicles, active suspensions controlled by embedded computing elements for preventing rollover have received a lot of attention. The existing models for synthesizing and allocating forces in such suspensions are conservatively based on the constraints that are valid until no wheels lift off the ground. However, the fault tolerance of the rollover-preventive systems can be enhanced if the smart/active suspensions can intervene in the more severe situation in which the wheels have just lifted off the ground. The difficulty in computing control in the last situation is that the vehicle dynamics then passes into the regime that yields a model involving disjunctive constraints on the dynamics. Simulation of dynamics with disjunctive constraints in this context becomes necessary to estimate, synthesize, and allocate the intended hardware realizable forces in an active suspension. In this paper, we give an algorithm for the previously mentioned problem by solving it as a disjunctive dynamic optimization problem. Based on this, we synthesize and allocate the roll-stabilizing time-dependent active suspension forces in terms of sensor output data. We show that the forces obtained from disjunctive dynamics are comparable with existing force allocations and, hence, are possibly realizable in the existing hardware framework toward enhancing the safety and fault tolerance.

Agglomeration front dynamics: Drying in sessile nano-particle laden droplets

The drying of sessile, nano-silica laden water droplet is studied under ambient conditions, in the absence of any convection. The drying process can be divided into two distinct regimes. During regime 1, the outer edge of the droplet remains pinned and particles agglomerate at the droplet periphery similar to the traditional coffee ring. However in regime 2, with further evaporation, both the liquid contact line and the agglomeration front starts moving radially inwards from the initial contact edge. The contact between the liquid and the agglomerate is maintained throughout regime 2 and the vaporisation driven liquid edge recession essentially drives the inward growth of the particle deposition. Fast kinetics of particle aggregation results in rapid growth of this agglomeration front as seen from the experiments. A theoretical formulation involving a simplistic model of the agglomeration front growth based on particle mass balance has been proposed. (C) 2014 Elsevier Ltd. All rights reserved,

Nonlinear control of an air-breathing engine including its validation with vehicle guidance

An implementable nonlinear control design approach is presented for a supersonic air-breathing ramjet engine. The primary objective is to ensure that the thrust generated by the engine tracks the commanded thrust without violating the operational constraints. An important constraint is to manage the shock wave location in the intake so that it neither gets detached nor gets too much inside the intake. Both the objectives are achieved by regulating the fuel flow to the combustion chamber and by varying the throat area of the nozzle simultaneously. The design approach accounts for the nonlinear cross-coupling effects and nullifies those. Also, an extended Kalman filter has been used to filter out the sensor and process noises as well as to make the states available for feedback. Furthermore, independent control design has been carried out for the actuators. To test the performance of the engine for a realistic flight trajectory, a representative trajectory is generated through a trajectory optimization process, which is augmented with a newly-developed finite-time state dependent Riccati equation technique for nullifying the perturbations online. Satisfactory overall performance has been obtained during both climb and cruise phases. (C) 2015 Elsevier Masson SAS. All rights reserved.

Forebody Compressibility Research of Hypersonic Vehicle

Three kinds of forebody model of hypersonic vehicles were studied with numerical simulation method. It shows that the two- order compressive ramp model is the best selection among the three for its good evaluative parameters value at the cowl of the inlet . This model can provide higher value of flux coefficient and total pressure recovery coefficient and lower average Mach number compared with those of the other two models . Simultaneously different compressive angles may have different effects . The configuration which the firstorder of compressive angle is 4°and the second 5°is the optimum combination. Furthermore factors such as attack angle were concerned. Better result may be obtained with a range of attack angles . Based on the work above the integrated design for forebodyPinlet of a hypersonic vehicle was performed. The numerical result shows that this integrated model provides good flow field quality for inlet and engine work.