Algumas Contribuições para Algoritmos de Controle de Filtros Ativos e Híbridos Conectados em Paralelo com Redes Elétricas Trifásicas a 3 ou a 4 Fios.

Este trabalho apresenta contribuições para algoritmos de controle utilizados em filtros ativos e híbridos conectados em redes elétricas trifásicas a 3 ou a 4 fios. Em relação aos algoritmos de controle para filtros ativos, a contribuição consiste em estender o conceito da filtragem harmônica seletiva para compensação de correntes harmônicas e desequilibradas em uma rede trifásica a 4 fios. Esses algoritmos derivam dos conceitos utilizados na teoria da potência instantânea (teoria pq), em conjunto com um circuito de sincronismo PLL. É importante ressaltar que estes algoritmos não utilizam as correntes consumidas pelas cargas, ou seja, apenas as tensões no ponto da rede onde o filtro está conectado são utilizadas para determinação das correntes harmônicas de referência. Apenas as correntes na saída do conversor são utilizadas como realimentação do controle PWM. Estes algoritmos também foram utilizados no filtro híbrido para compensação de correntes harmônicas em uma rede trifásica a 3 fios. Por fim foi feito uma alteração nesses algoritmos de controle que permite eliminar as correntes utilizadas na realimentação do controle PWM. Resultados de simulação são apresentados com objetivo de observar o comportamento desses algoritmos tanto no filtro ativo quanto no híbrido nas condições mencionadas.

Associação entre o consumo de oxigênio e as alterações na microcirculação de pacientes pediátricos com choque séptico

Choque séptico é caracterizado por desequilíbrio entre o transporte e o consumo de oxigênio, podendo acarretar hipóxia tecidual. A disfunção microcirculatória, característica cardinal da fisiopatologia do choque séptico, causa má distribuição de fluxo sanguíneo microvascular e, consequentemente, shunt de oxigênio, disóxia tissular e, teoricamente, diminuição no consumo de oxigênio (VO2) pela célula. No presente estudo, foi investigada a associação entre alterações microcirculatórias causadas pela sepse e o consumo de oxigênio em pacientes pediátricos. Dezessete crianças com choque séptico ressuscitadas foram estudadas em quatro momentos durante a internação na unidade de terapia intensiva (dentro de 24, 48 e 72 horas após a admissão ou diagnóstico de choque e após a resolução deste, antes da extubação traqueal). A microcirculação sublingual foi avaliada utilizando o método de imagem Sidestream dark field (SDF) e o VO2 foi calculado através da calorimetria indireta. Outras variáveis hemodinâmicas, como transporte de oxigênio, índice cardíaco, pressão arterial invasiva, lactato arterial e saturação venosa central, foram coletadas. Embora as variáveis hemodinâmicas tenham se mantido em níveis satisfatórios, graves alterações na microcirculação foram visualizadas, especialmente na densidade de vasos pequenos perfundidos (DVPP), na proporção de vasos pequenos perfundidos (PVPP) e no índice de fluxo microvascular (MFI). Foram encontradas assosciações significativas entre o VO2 e os parâmetros da microcirculação: dVO2 e dDVPP (β coefficient= 6,875; p<0,001), dVO2 e dPVPP (β coefficient=92,246; p<0,001) e dVO2 e dMFI (β coefficient=21,213; p<0,001). Não foram encontradas correlações entre as alterações microcirculatórias e as outras variáveis. Em conclusão, este estudo mostrou que pacientes pediátricos com choque séptico apresentaram grave disfunção microvascular e que o fluxo microcirculatório alterado estava associado ao VO2, podendo estar implicado na fisiopatologia da disóxia tecidual da sepse.

Use of skeletochronological analysis to estimate the age of leatherback sea turtles Dermochelys coriacea in the western North Atlantic

Although growth rate and age data are essential for leatherback management, estimates of these demographic parameters remain speculative due to the cryptic life history of this endangered species. Skeletochronological analysis of scleral ossicles obtained from 8 captive, known-age and 33 wild leatherbacks originating from the western North Atlantic was conducted to characterize the ossicles and the growth marks within them. Ages were accurately estimated for the known-age turtles, and their growth mark attributes were used to calibrate growth mark counts for the ossicles from wild specimens. Due to growth mark compaction and resorption, the number of marks visible at ossicle section tips was consistently and significantly greater than the number visible along the lateral edges, demonstrating that growth mark counts should be performed at the tips so that age is not underestimated. A correction factor protocol that incorporated the trajectory of early growth increments was used to estimate the number of missing marks in those ossicles exhibiting resorption, which was then added to the number of observed marks to obtain an age estimate for each turtle. A generalized smoothing spline model, von Bertalanffy growth curve, and size-at-age function were used to obtain estimates of age at maturity for leatherbacks in the western North Atlantic. Results of these analyses suggest that median age at maturation for leatherbacks in this part of the world may range from 24.5 to 29 yr. These age estimates are much greater than those proposed in previous studies and have significant implications for population management and recovery.

Leaf growth of the seagrass Syringodium filiforme in outer Florida Bay, Florida

Leaf growth of the seagrass Syringodium filiforme (Kütz., 1860) was determined using a new technique based on the growth of emergent leaves (EL method) and compared to the more labor intensive repeated measurements (RM) and demographic allometric age reconstruction techniques (DA). All three techniques were used to compare leaf growth dynamics of plants with different morphologies at two sites, a shallow water (0.5 m) banktop and an adjacent deeper water (1.5 m) environment in outer Florida Bay, Florida. Leaf formation rates (Leaf Plastochrone Interval or PI) determined using the EL and RM methods were nearly identical, with means of 20 and 21 d leaf–1 at both sites, significantly faster than the 30 d leaf–1 calculated using the DA method. The EL method produced the highest estimate of leaf growth, 1.8 and 1.9 cm d–1 at the 0.5 m and 1.5 m sites, respectively, followed by the RM method (1.3 and 1.3 cm d–1) and the DA method (1.0 and 1.1 cm d–1). None of the methods detected differences in leaf PI, leaf growth or leaf fragmentation rates between sites. However, leaves at the 1.5 m site typically retained intact leaf tips longer than those at the 0.5 m site, and total leaf lifespan was longer at the 1.5 m site. Based on these results and the amount of field and laboratory work required by each of the methods, the new EL method is the preferred technique for monitoring leaf growth in S. filiforme.

A preliminary account and review of the simple methods for determining the operational parameters of fishing gear, underwater, with notes on its application

An account and review of the simple methods for determining the operational parameters of fishing gear, underwater, such a tilt of otter boards (outwards or inwards, forwards or afterwards), vertical height of net, its horizontal spread, angle of divergence at bosom, spread between wing tips, angle of inclination of danlenos, butterfly, slope of legs and sweep-line has been given. The relationship of distance between the otter boards spread and the vertical height of net has been obtained as generally linear. The possibilities of regulating the vertical height of net (dependent variate) and spread of otter boards (independent variate) for increasing the fishing efficiency has been discussed. The angle of attack of oval shaped otter boards used during the operations still remain undetermined, however, it has been explained how the best angle of attack for increasing the efficiency of gear can be obtained by regulating the ratio of depth to warp for a given net. The inadequacy of the mere indices of catch per hour of trawling in comparing the relative efficiency of trawls in gear research studies has been indicated. The importance of estimating the operational parameters and its application to commercial fisheries depending upon the distribution pattern of fish and in gear research has been discussed. The efficiency of the jelly bottle method has been compared statistically with the observations made on the trawl gear underwater with instruments.

Effect of blade tip geometry on the tip leakage flow in axial turbine cascades

The phenomenon of tip leakage has been studied in two linear cascades of turbine blades. The investigation includes an examination of the performance of the cascades with a variety of tip geometries. The effects of using plain tips, suction side squealers, and pressure side squealers are reported. Traverses of the exit flow field were made in order to determine the overall performance. A method of calculating the tip discharge coefficients for squealer geometries is put forward. In linking the tip discharge coefficient and cascade losses, a procedure for predicting the relative performance of tip geometries is developed. The model is used to examine the results obtained using the different tip treatments and to highlight the important aspects of the loss generation process.

Eyes on their fingertips: some aspects of the arts, science, technology and culture of the fisherfolk of Trivandrum, India

Eyes on Their Finger Tips deals with the traditional marine wisdom of a set of people and the rarest of rare experiences they have had at sea. Through these numerous chapters he takes us into the seas of the fishers. It is a voyage which we cannot make in reality. But through the heroic deeds of his father, the riddles of oldman Sebesti, the shark story of brother Kamalappan, and the rituals of his mother, we get a fascinating peep into the wisdom of the watery world of the small-scale fishers of Trivandrum, Kerala, India.

A metal-polymer composite with unusual properties

Electrically conductive composites that contain conductive filler dispersed in an insulating polymer matrix are usually prepared by the vigorous mixing of the components. This affects the structure of the filler particles and thereby the properties of the composite. It is shown that by careful mixing nano-scale features on the surface of the filler particles can be retained. The fillers used possess sharp surface protrusions similar to the tips used in scanning tunnelling microscopy. The electric field strength at these tips is very large and results in field assisted (Fowler-Nordheim) tunnelling. In addition the polymer matrix intimately coats the filler particles and the particles do not come into direct physical contact. This prevents the formation of chains of filler particles in close contact as the filler content increases. In consequence the composite has an extremely high resistance even at filler loadings above the expected percolation threshold. The retention of filler particle morphology and the presence of an insulating polymer layer between them endow the composite with a number of unusual properties. These are presented here together with appropriate physical models. © 2005 IOP Publishing Ltd.

Rain igestion in axial flow compressors at part speed

New experimental work is reported on the effects of water ingestion on the performance of an axial flow compressor. The background to the work is the effect that heavy rain has on an aeroengine compressor when operating in a "descent idle" mode, i.e., when the compressor is operating at part speed and when the aeromechanical effects of water ingestion are more important than the thermodynamic effects. Most of our existing knowledge in this field comes from whole engine tests. The current work provides the first known results from direct measurements on a stand-alone compressor. The influence of droplet size on path trajectory is considered both computationally and experimentally to show that most rain droplets will collide with the first row of rotor blades. The water on the blades is then centrifuged toward the casing where the normal airflow patterns in the vicinity of the rotor tips are disrupted. The result of this disruption is a reduction in compressor delivery pressure and an increase in the torque required to keep the compressor speed constant. Both effects reduce the efficiency of the machine. The behavior of the water in the blade rows is examined in detail, and simple models are proposed to explain the loss of pressure rise and the increase in torque. The measurements were obtained in a low speed compressor, making it possible to study the mechanical (increase in torque) and aerodynamic (reduction in pressure rise) effects of water ingestion without the added complication of thermodynamic effects. Copyright © 2008 by ASME.

Measuring shaft friction during earthquakes

The failure of piled foundations has been observed in many earthquake events. The manner in which a pile is able to support its applied superstructure loading during an earthquake is not yet fully understood, particularly with respect to the shaft friction capacity. In this paper, new pile group is presented which has been instrumented to measure the shaft friction distribution along the length of a pile. In addition, this pile group is able to measure the pore pressures directly beneath the pile tips. The pile group was tested in dynamic centrifuge experiments and showed differing shaft friction behaviour in dense and loose soil layers as well as strong dilation beneath the pile tips at the start of earthquake loading. A reduction in shaft friction was observed after the earthquake due to soil down-drag. © 2010 Taylor & Francis Group, London.

Fracture toughness of fibrous membranes

Random fibrous networks exist in both natural biological and engineering materials. While the nonlinear deformation of fibrous networks has been extensively studied, the understanding of their fracture behaviour is still incomplete. To study the fracture toughness of fibrous materials, the near-tip region is crucial because failure mechanisms such as fibril rupture occur in this region. The consideration of this region in fracture studies is, however, a difficult task because it involves microscopic mechanical responses at a small length scale. This paper extends our previous finite element analysis by incorporating the microscopic responses into a macroscopic domain by using a submodeling technique. The detailed study of microstructures at crack tips show a stochastic toughness of membranes due to the random nature of fibrous networks. Further, the sizes of crack tip region, which are sufficient to provide a reasonable prediction of fracture behaviour in a specific type of fibrous network, were presented. Future work includes improving the current linear assumption in the macroscopic models to become nonlinear.

Angular distribution of field emitted electrons from vertically aligned carbon nanotube arrays

Angular field emission (FE) properties of vertically aligned carbon nanotube arrays have been measured on samples grown by plasma enhanced chemical vapor deposition and characterized by scanning electron microscope and I-V measurements. These properties determine the angular divergence of electron beams, a crucial parameter in order to obtain high brilliance FE based cathodes. From angular distributions of the electron beam transmitted through extraction grids of different mesh size and by using ray-tracing simulations, the maximum emission angle from carbon nanotube tips has been determined to be about ± 30 around the tube main axis. © 2012 American Institute of Physics.

Self-regulating casing treatment for axial compressor stability enhancement

The operating range of an axial compressor is often restricted by a safety imposed stall margin. One possible way of regaining operating range is with the application of casing treatment. Of particular interest here is the type of casing treatment which extracts air from a high pressure location in the compressor and re-injects it through discrete loops into the rotor tip region. Existing re-circulation systems have the disadvantage of reducing compressor efficiency at design conditions because worked flow is unnecessarily re-circulated at these operating conditions. Re-circulation is really only needed near stall. This paper proposes a self-regulating casing treatment in which the re-circulated flow is minimized at compressor design conditions and maximized near stall. The self-regulating capability is achieved by taking advantage of changes which occur in the tip clearance velocity and pressure fields as the compressor is throttled toward stall. In the proof-of-concept work reported here, flow is extracted from the high pressure region over the rotor tips and re-injected just upstream of the same blade row. Parametric studies are reported in which the flow extraction and re-injection ports are optimized for location, shape and orientation. The optimized design is shown to compare favorably with a circumferential groove tested in the same compressor. The relationship between stall inception type and casing treatment effectiveness is also investigated. The self-regulating aspect of the new design works well: stall margin improvements from 2.2 to 6.0% are achieved for just 0.25% total air re-circulated near stall and half that near design conditions. The self-regulating capability is achieved by the selective location and orientation of the extraction hole; a simple model is discussed which predicts the optimum axial location. Copyright © 2011 by ASME.

Performing quantitative MFM measurements on soft magnetic nanostructures.

We have extended our previous work (Rawlings et al 2010 Phys. Rev. B 82 085404) on simulating magnetic force microscopy (MFM) images for magnetically soft samples to include an accurate representation of coated MFM tips. We used an array of square 500 nm nanomagnets to evaluate our improved MFM model. A quantitative comparison between model and experiment was performed for lift heights ranging from 20 to 100 nm. No fitting parameters were used in our comparison. For all lift heights the qualitative agreement between model and experiment was significantly improved. At low lift heights, where the magnetic signal was strong, the difference between theory and experiment was less than 30%.

High-order DES and zonal LES of a labyrinth seal

Hybrid numerical large eddy simulation (NLES) and detached eddy simulation (DES) methods are assessed on a labyrinth seal geometry. A high sixth order discretization scheme is used and is validated using a test case of a two dimensional vortex. The hybrid approach adopts a new blending function and along with DES is initially validated using a simple cavity flow. The NLES method is also validated outside of RANS zones. It is found that there is very little resolved turbulence in the cavity for the DES simulation. For the labyrinth seal calculations the DES approach is problematic giving virtually no resolved turbulence content. It is seen that over the tooth tips the extent of the LES region is small and is likely to be a strong contributor to excessive flow damping in these regions. On the other hand the zonal Hamilton-Jacobi approach did not suffer from this trait. In both cases the meshes used are considered to be hybrid RANS-LES adequate. Fortunately (or perhaps unfortunately) the DES profiles are in agreement with the time mean experimental measurements. It is concluded that for an inexperienced CFD practitioner this could have wider implications particularly if transient results such as unsteady loading are desired. Copyright © 2012 by the American Institute of Aeronautics and Astronautics, Inc.