Microparticulated Hydrochlorothiazide Solid Dispersion: Enhancing Dissolution Properties via Spray Drying

The aim of the present study was to obtain microparticles of hydrochlorothiazide, a diuretic drug that practically insoluble in water, by spray drying and to investigate the influence of process parameters using a three-level, three-factor Box-Behnken design. Process yields, moisture content, particle size, flowability, and solubility were used to evaluate the spray-dried microparticles. The data were analyzed by response surface methodology using analysis of variance. The independent variables studied were outlet temperature, atomization pressure, and drug content. The formulations were prepared using polyvinylpyrrolidone and colloidal silicon dioxide as the hydrophilic carrier and drying aid, respectively. The microparticle yield ranged from 18.15 to 59.02% and resulted in adequate flow (17 to 32 degrees), moisture content between 2.52 to 6.18%, and mean particle size from 45 to 59 mu m. The analysis of variance showed that the factors studied influenced the yields, moisture content, angle of repose, and solubility. Thermal analysis and X-ray diffractometry evidenced no drug interactions or chemical modifications. Photomicrographs obtained by scanning electron microscopy showed spherical particles. The solubility and dissolution rates of hydrochlorothiazide were remarkably improved when compared with pure drug. Therefore, the results confirmed the high potential of the spray-drying technique to obtain microparticulate hydrochlorothiazide with enhanced pharmaceutical and dissolution properties.

Witzkeite: A new rare nitrate-sulphate mineral from a guano deposit at Punta de Lobos, Chile

Witzkeite, ideally Na4K4Ca(NO3)(2)(SO4)(4)center dot 2H(2)O, is a new mineral found in the oxidation zone of the guano mining field at Punta de Lobos, Tarapaca region, Chile. It occurs as colorless, tabular crystals up to 140 mu m in length, associated with dittmanite and nitratine. Witzkeite is colorless and transparent, with a white streak and a vitreous luster. It is brittle, with Molts hardness 2 and distinct cleavage on {001}. Measured density is 2.40(2) g/cm(3), calculated density is 2.403 g/cm(3). Witzkeite is biaxial (-) with refractive indexes alpha = 1.470(5), beta = 1.495(5), gamma = 1.510(5), measured 2V = 50-70 degrees. The empirical composition is (electron microprobe, mean of five analyses, H2O, CO2, and N2O5 by gas chromatography; wt%): Na2O 12.83, K2O 22.64, CaO 7.57, FeO 0.44, SO3 39.96, N2O5 12.7, H2O 4.5, total 100.64; CO2 was not detected. The chemical formula, calculated based on 24 O, is: Na3.40K3.95Ca1.11Fe0.05(NO3)(1.93)(SO4)(4.10)(H4.10O1.81). Witzkeite is monoclinic, space group C2/c, with unit-cell parameters: a = 24.902(2), b = 5.3323(4), c = 17.246(1) angstrom, beta = 94.281(7)degrees, V = 2283.6(3) angstrom(3) (Z = 4). The crystal structure was solved using single-crystal X-ray diffraction data and refined to R-1(F) = 0.043. Witzkeite belongs to a new structure type and is noteworthy for the very rare simultaneous presence of sulfate and nitrate groups. The eight strongest X-ray powder-diffraction lines [d in angstrom (I in %) (h k l)] are: 12.38 (100) (2 0 0), 4.13 (19) (6 0 0), 3.10 (24) (8 0 0), 2.99 (7) ((8) over bar 02), 2.85 (6) (8 02), 2.69 (9) ((7) over bar 1 3), 2.48 (12) (10 0 0), and 2.07 (54) (12 0 0). The IR spectrum of witzkeite was collected in the range 390-4000 cm(-1). The spectrum shows the typical bands of SO42- ions (1192, 1154, 1116, 1101, 1084, 993, 634, and 617 cm(-1)) and of NO3- ions (1385, 1354, 830, 716, and 2775 cm(-1)). Moreover, a complex pattern of bands related to H2O is visible (bands at 3565, 3419, 3260, 2405, 2110, 1638, and 499 cm(-1)). The IR spectrum is discussed in detail.

Protection of Bifidobacterium lactis and Lactobacillus acidophilus by microencapsulation using spray-chilling

The aim of this study was to produce and evaluate solid lipid microparticles containing Bifidobacterium lactis or Lactobacillus acidophilus. Survival assays were conducted to evaluate the resistance of the probiotics to spray-chilling process, their resistance to simulated gastric fluid (SGF) and simulated intestinal fluid (SIF) and their stability during 90 d of storage. The viability of the cells was not affected by microencapsulation. The free and encapsulated cells of B. lactis were resistant to SGF and SIF. The microencapsulation, however, provided protection for L. acidophilus against SGF and SIF. The free and encapsulated microorganisms lost their viability when they were stored at 37 degrees C. However, promising results were obtained when refrigerated and frozen storage was applied. The study indicates that spray-chilling using fat as carrier can be considered an innovative technology and matrix, respectively, for the protection, application and delivery of probiotics. (C) 2012 Elsevier Ltd. All rights reserved.

Microencapsulation of Ketoprofen in Blends of Acrylic Resins by Spray Drying

Microparticles of ketoprofen entrapped in blends of acrylic resins (Eudragit RL 30D and RS 30D) were successfully produced by spray drying. The effects of the proportion ketoprofen : polymer (1: 1 and 1: 3) and of spray-drying parameters (drying gas inlet temperatures of 80 and 100 degrees C; microencapsulating composition feed flow rates of 4 and 6 g/min) on the microparticles properties (drug content, encapsulation efficiency, mean particle size, moisture content, and dissolution behavior) were evaluated. Differential scanning calorimetry (DSC) thermograms and X-ray diffractograms of the spray-dried product, the free drug, and the physical mixture between the free drug and spray-dried composition (blank) were carried out. Microparticles obtained at inlet temperature of 80 degrees C, feed flow rate of 4 g/min, and ketoprofen : acrylic resin ratio of 1: 3 presented an encapsulation efficiency of 88.1%, moisture content of 5.8%, production yield around 50%, and a higher reduction in dissolution rate of the entrapped ketoprofen. Sigmoidal shape dissolution profiles were presented by the spray-dried microparticles. The dissolution profiles were relatively well described by the Weibull model, a showing high coefficient of determination, R-2, and a mean absolute error between experimental and estimated values of between 4.6 and 10.1%.

Engineering Active Pharmaceutical Ingredients by Spray Drying: Effects on Physical Properties and In Vitro Dissolution

Active pharmaceutical ingredients have very strict quality requirements; minor changes in the physical and chemical properties of pharmaceuticals can adversely affect the dissolution rate and therefore the bioavailability of a given drug. Accordingly, the aim of the present study was to investigate the effect of spray drying on the physical and in vitro dissolution properties of four different active pharmaceutical ingredients, namely carbamazepine, indomethacin, piroxicam, and nifedipine. Each drug was dispersed in a solution of ethanol and water (70:30) and subjected to single-step spray drying using similar operational conditions. A complete characterization of the spray-dried drugs was performed via differential scanning calorimetry (DSC), scanning electron microscopy (SEM), X-ray powder diffraction (XRPD), particle size distribution analysis, solubility analysis, and an in vitro dissolution study. The results from the thermal analysis and X-ray diffraction showed that, except for carbamazepine, no chemical modifications occurred as a result of spray drying. Moreover, the particle size distribution of all the spray-dried drugs significantly decreased. In addition, SEM images showed that most of the particles had an irregular shape. There was no significant improvement in the solubility of the spray-dried drugs compared with the unprocessed compounds; however, in general, the dissolution rates of the spray-dried drugs showed a remarkable improvement over their non-spray-dried counterparts. Therefore, the results from this study demonstrate that a single spray-drying step may lead to changes in the physical properties and dissolution characteristics of drugs and thus improve their therapeutic action.

Numerical simulation of an ethanol turbulent spray flame with RANS and diffusion combustion model

A detailed numerical simulation of ethanol turbulent spray combustion on a rounded jet flame is pre- sented in this article. The focus is to propose a robust mathematical model with relatively low complexity sub- models to reproduce the main characteristics of the cou- pling between both phases, such as the turbulence modulation, turbulent droplets dissipation, and evaporative cooling effect. A RANS turbulent model is implemented. Special features of the model include an Eulerian– Lagrangian procedure under a fully two-way coupling and a modified flame sheet model with a joint mixture fraction– enthalpy b -PDF. Reasonable agreement between measured and computed mean profiles of temperature of the gas phase and droplet size distributions is achieved. Deviations found between measured and predicted mean velocity profiles are attributed to the turbulent combustion modeling adopted

Deposit-feeding in benthic macrofauna : Tracer studies from the Baltic Sea

A low content of organic matter, which is largely refractory in nature, is characteristic of most sediments, meaning that aquatic deposit-feeders live on a very poor food source. The food is derived mainly from sedimenting phytodetritus, and in temperate waters like the Baltic Sea, from seasonal phytoplankton blooms. Deposit-feeders are either bulk-feeders, or selective feeders, which preferentially ingest the more organic-rich particles in the sediment, including phytodetritus, microbes and meiofauna. The soft-bottom benthos of the Baltic Sea has low species biodiversity and is dominated by a few macrobenthic species, among which the most numerous are the two deposit-feeding amphipods Monoporeia affinis and Pontoporeia femorata, and the bivalve Macoma balthica. This thesis is based on laboratory experiments on the feeding of these three species, and on the priapulid Halicryptus spinulosus. Feeding by benthic animals is often difficult to observe, but can be effectively studied by the use of tracers. Here we used the radioactive isotope 14C to label food items and to trace the organic matter uptake in the animals, while the stable isotopes 13C and 15N were used to follow feeding on aged organic matter in the sediment. The abundance of M. balthica and the amphipods tends to be negatively correlated, i.e., fewer bivalves are found at sites with dense populations of amphipods, with the known explanation that newly settled M. balthica spat are killed by the amphipods. Whether the postlarvae are just accidentally killed, or also ingested after being killed was tested by labelling the postlarvae with 14C and Rhodamine B. Both tracer techniques gave similar evidence for predation on and ingestion of postlarval bivalves. We calculated that this predation was likely to supply less than one percent of the daily carbon requirement for M. affinis, but might nevertheless be an important factor limiting recruitment of M. balthica. The two amphipods M. affinis and P. femorata are partly vertically segregated in the sediment, but whether they also feed at different depths was unknown. By adding fresh 14C-labelled algae either on the sediment surface or mixed into the sediment, we were able to distinguish surface from subsurface feeding. We found M. affinis and P. femorata to be surface and subsurface deposit-feeders, respectively. Whether the amphipods also feed on old organic matter, was studied by adding fresh 14C-labelled algae on the sediment surface, and using aged, one-year-old 13C- and 15N-labelled sediment as deep sediment. Ingestion of old organic matter, traced by the stable isotopes, differed between the two species, with a higher uptake for P. femorata, suggesting that P. femorata utilises the older, deeper-buried organic matter to a greater extent. Feeding studies with juveniles of both M. affinis and P. femorata had not been done previously. In an experiment with the same procedure and treatments as for the adults, juveniles of both amphipod species were found to have similar feeding strategies. They fed on both fresh and old sediment, with no partitioning of food resources, making them likely to be competitors for the same food resource. Oxygen deficiency has become more wide-spread in the Baltic Sea proper in the last half-century, and upwards of 70 000km2 are now devoid of macrofauna, even though part of that area does not have oxygen concentrations low enough to directly kill the macrofauna. We made week-long experiments on the rate of feeding on 14C-labelled diatoms spread on the sediment surface in different oxygen concentrations for both the amphipod species, M. balthica and H. spinulosus. The amphipods were the most sensitive to oxygen deficiency and showed reduced feeding and lower survival at low oxygen concentrations. M. balthica showed reduced feeding at the lowest oxygen concentration, but no mortality increase. The survival of H. spinulosus was unaffected, but it did not feed, showing that it is not a surface deposit-feeder. We conclude that low oxygen concentrations that are not directly lethal, but reduce food intake, may lead to starvation and death in the longer term.

Photocatalytic activity of nanostructured anatase coatings obtained by cold gas spray

[EN] This article describes a photocatalytic nanostructured anatase coating deposited by cold gas spray (CGS) supported on titanium sub-oxide (TiO22x) coatings obtained by atmospheric plasma spray (APS) onto stainless steel cylinders. The photocatalytic coating was homogeneous and preserved the composition and nanostructure of the starting powder. The inner titanium sub-oxide coating favored the deposition of anatase particles in the solid state. Agglomerated nano-TiO2 particles fragmented when impacting onto the hard surface of the APS TiO22x bond coat. The rough surface provided by APS provided an ideal scenario for entrapping the nanostructured particles, which may be adhered onto the bond coat due to chemical bonding; a possible bonding mechanism is described. Photocatalytic experiments showed that CGS nano-TiO2 coating was active for photodegrading phenol and formic acid under aqueous conditions. The results were similar to the performance obtained by competitor technologies and materials such as dip-coating P25 photocatalysts. Disparity in the final performance of the photoactive materials may have been caused by differences in grain size and the crystalline composition of titanium dioxide.

Microincapsulazione di nanoparticelle di argento tramite tecnica spray-freeze-drying

Per limitare gli effetti tossici delle Ag-NPs, si è pensato che esse possano essere utilizzate in forma di microincapsulati, in quanto le microcapsule possono avere una certa velocità di rilascio sotto specifiche condizioni. Incapsulando quindi le Ag-NPs, posso ottenere un rilascio controllato di esse, in modo da ottenere una concentrazione di esse utile allo scopo per cui vengono impiegate, evitando un sovradosaggio che non porterebbe alcun beneficio ma solo a una maggior probabilità di causare effetti tossici.

Conjunctival Proliferation After a Mild Pepper Spray Injury in a Young Child

PURPOSE To report a case of conjunctival proliferation in a 2.5-year-old boy after initial evidence of a mild chemical injury after ocular exposure to pepper spray (oleoresin capsicum). METHODS Case report with ophthalmologic and histologic findings. RESULTS A child presented with mild conjunctival injection and chemosis without any corneal erosion after direct exposure to pepper spray. Three weeks later, a significant conjunctival proliferation was found at the limbus, which was refractory to treatment with topical corticosteroids. Finally, proliferative tissue was surgically excised without clinical recurrence during 2 months of follow-up. CONCLUSIONS We hypothesize that the young age of the patient may have been an important factor for the severe conjunctival proliferation in comparison to a mainly uncomplicated course of pepper spray injuries in most adults. We recommend the use of topical antiinflammatory treatment even in apparently mild pepper spray injuries, especially in young children.