Fabrication of Mg foams for biomedical applications by means of a replica method based upon spherical carbon particles

Interest in Mg foams is increasing due to their potential use as biomaterials. Fabrication methods determine to a great extent their structure and, in some cases, may pollute the foam. In this work Mg foams are fabricated by a replica method that uses as skeleton packed spheres of active carbon, a material widely utilized in medicine. After Mg infiltration, carbon particles are eliminated by an oxidizing heat treatment. The latter covers Mg with MgO which improves performance. In particular, oxidation retards degradation of the foam, as the polarization curves of the Mg foam with and without oxide indicate. The sphericity and regularity of C particles allows control of the structure of the produced open-cell foams.

Effects of infiltration pressure on mechanical properties of Al–12Si/graphite composites for piston engines

In this work results for the flexural strength and the thermal properties of interpenetrated graphite preforms infiltrated with Al-12wt%Si are discussed and compared to those for packed graphite particles. To make this comparison relevant, graphite particles of four sizes in the range 15–124 μm, were obtained by grinding the graphite preform. Effects of the pressure applied to infiltrate the liquid alloy on composite properties were investigated. In spite of the largely different reinforcement volume fractions (90% in volume in the preform and around 50% in particle compacts) most properties are similar. Only the Coefficient of Thermal Expansion is 50% smaller in the preform composites. Thermal conductivity of the preform composites (slightly below 100 W/m K), may be increased by reducing the graphite content, alloying, or increasing the infiltration pressure. The strength of particle composites follows Griffith criterion if the defect size is identified with the particle diameter. On the other hand, the composites strength remains increasing up to unusually high values of the infiltration pressure. This is consistent with the drainage curves measured in this work. Mg and Ti additions are those that produce the most significant improvements in performance. Although extensive development work remains to be done, it may be concluded that both mechanical and thermal properties make these materials suitable for the fabrication of piston engines.

Synthesis and characterization of low-cost materials for aqueous Na-ion batteries

136 p.

Uma proposta de síntese para o ensino integrado das disciplinas experimentais de química orgânica e inorgânica nos cursos de graduação

The synthesis of the layered compound VO(PO4)(H2O)2 and its use to oxidize 2-butanol to the ketone 2-butanone, is proposed as an experiment to integrate the organic and inorganic experimental undergraduate chemistry courses, in an atempt to overcome the observed disrupture between organic and inorganic chemistry.

Una propuesta de actividades para el laboratorio integrado de Química Orgánica e Inorgánica : experimentación en Síntesis Química.

Realizado en los laboratorios de Química Orgánica e Inorgánica de la Facultad de Ciencias de la Universidad de Burgos por profesores que trabajan en esos departamentos. El objetivo fundamental planteado es la selección de un conjunto de experimentos que pueden realizarse de modo integrado en los cursos de experimentación de Síntesis Química, asignatura troncal en los nuevos planes de estudios de la licenciatura de Química. El sistema de trabajo ha consistido en la selección de experimentos de compuestos o productos inorgánicos de utilidad en sístesis orgánicas. Los resultados obtenidos durante el curso académico 2000-2001 no han podido ser incorporados, por ello no se ha sometido a evaluación para conocer si favorece el aprendizaje de los alumnos. No se han realizado guiones nuevos puesto que los experimentos seleccionados se hallan bien descritos en los textos prácticos. El esfuerzo se ha centrado en el análisis del potencial integrador de los experimentos. No obstante se acompañan fichas de cada par de experimentos en las que se hacen comentarios de interés para su utilización. No se ha publicado el trabajo, pero se ha constatado el gran potencial integrador de algunos nuevos experimentos que merecen ser optimizados y publicados.

Análise de fragmentos arqueológicos: um diálogo entre a Química, Biologia e Arqueologia

Dissertação de mestrado em Técnicas de Caracterização e Análise Química

O uso de radiação ultravioleta para o pré-tratamento de amostras em análise inorgânica

The basic principles of UV irradiation as sample pre-treatment step and its potential for inorganic analysis are illustrated and discussed through significant examples from the literature. Not only does this overview cover the classical applications of this technique in the decomposition of organic matter in electroanalysis, but it also presents recent trends, including the increasing interest in employing UV irradiation in flow analytical systems, successful attempts to enhance its effectiveness and the coupling with chromatographic and spectroscopic methodologies. Furthermore, a number of relevant cases of UV-driven derivatization reactions involving photo-sensitive inorganic species are presented, showing some convenient options to perform fast and reliable determination of inorganic and organic analytes.

A aplicação da fotoquímica inorgânica nas diversas áreas da ciência

This article provides an overview of the current status of research involving the photochemical behavior of transition metal complexes in the following important areas: medicine, biology and materials science including some of the experiences of the writer. Coverage is selective, generally focusing on highlights and the most recent developments, with the broad aim of showing the interdisciplinary field of inorganic photochemistry.

Estudo da adsorção de surfactante catiônico na matriz inorgânica fosfato de nióbio hidratado

This work describes the study the adsorption of a cationic surfactant, cetyl trimethyl ammonium bromide (CTAB) in the hydrous niobium phosphate matrix. The matrix was characterized by powder X-ray diffraction (DRX), thermal analysis (TG), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and surface area measurements (BET). The Langmuir and Freundlich isothermal models were used in the CTAB adsorption study. The adsorption process wasn`t favorable for the NbOPO4.nH2O in both studied models.

Caracterização do material particulado fino e grosso e composição da fração inorgânica solúvel em água em São José dos Campos (SP)

Air samples of fine (PM2,5) and coarse (PM2,5-10) particulate matter were collected in São José dos Campos from February 2004 to February 2005. Average PM10 mass concentrations was 31.2 ± 14.0 μg m-3, half of which belonging to the PM2.5 fraction. Ammonium and SO4(2-) were predominantly found in the fine fraction. Average (NH4)2SO4 concentration was estimated to be about 2.9 μg m-3. Chloride, Na+ and NO3- were mostly associated with PM2,5-10. Chloride deficits with respect to sea-salt Cl/Na ratio were found in both size fractions.

Abordagem teórico-experimental da teoria do campo cristalino na disciplina de síntese inorgânica

We describe herein the synthesis and characterization of the complexes KNiF3, [Ni(en)3]I2, [Ni(en)3]Cl2, [Ni(acac)2(H2O)2], [Ni(en)2(H2O)2]Cl2 and [Ni(NH3)6](BF4)2 (en = ethylenediamine, acac- = acetylacetonate) performed in the inorganic synthesis major course at the Chemistry Institute of UFRGS (Universidade Federal do Rio Grande do Sul). The compounds were characterized by infrared and electronic spectroscopy and the electrolytic conductivity was measured. The parameters 10Dq and B were obtained from the electronic spectra and the nefelauxetic and spectrochemical series were determined. The obtained spectrochemical series was F- < acac- < NH3 < en and the nefeulaxetic series was en < NH3 < acac- < F-.

Aplicació de les TIC a l'àrea de Física i Química. 'Aplicación de las TIC en el área de Física y Química'.

Resumen tomado de la publicación. Incluye imágenes de capturas de pantalla del ordenador sobre los software comentados. Se adjuntan actividades de consolidación del curso

Gran temática Planeta : Física y Química.

Para ver el contenido de los CD es necesario ejecutar el instalador (volumen 20)

Análise química de produtos de incrustação em dutos de petróleo por espectometria de fluorescência de raios X

The quantitative chemical characterization of the inorganic fraction of scale products is very relevant in studying, monitoring and controlling corrosive processes of oil pipelines. The X-ray fluorescence spectrometry (XRF) is a very versatile analytical technique, which can be used in quantitative analysis in solid samples at low concentrations of the chemical element, in the order of few ppm. A methodology that involves sample preparation diluted in the proportion of 1:7 (one portion of the sample for seven of wax), pressed as pellets was used in the XRF calibration for chemical analysis of scale products from oil pipelines. The calibration involved the preparation of reference samples from mixtures of P.A. reagents, aiming to optimize the time consumed in the steps of sample preparation and analysis of Al, Ba, Ca, Fe, K, Mg, Mn, Na, P, S, Si, Sr and Ti, using the same pressed pellet for trace and major elements analysis

Obtenção e caracterização físico-química de blendas poliméricas, baseadas em POE e PMMA, dopadas com dióxido de titânio

The study of polymer blends has been an alternative method in the search field of new materials for obtaining materials with improved properties. In this work blends of poly(methyl methacrylate) (PMMA) and poly(ethylene oxide) (PEO) doped with titanium dioxide (TiO2) were studied. The PEO is a polymer semicrystalline structure varying between, 70 and 84% crystallinity, while the PMMA exhibits behavior amorphous in their structure. The use of TiO2 is related to corrosion-resistant of titanium as well as good heat transfer and other characteristics. The study of these polymer blends doped TiO2 gives the properties junction organic (polymer) and inorganic (oxide) which leads to modification of the properties of the resultant material. The blends were doped TiO2 (POE/PMMA/TiO2) in different proportions of the PMMA with the PEO and TiO2 fixed. The ratios were: 90/10/0,1; 85/15/0, 1; 80/20/0,1, 75/25/0,1 and 70/30/0,1. The resulting material was obtained in powder form and being characterized by Fourier Transformed Infrared (FTIR) Spectroscopy, Scanning Electron Microscopy (SEM), X-Ray Diffraction (XRD), Thermogravimetric Analysis (TGA) and Electrochemical Impedance Spectroscopy (EIS). The infrared spectra (IR) for the blends in different ratios showed a band at 1744 cm-1, characteristic of the C=O stretching, which increases in intensity with increasing PMMA composition, while in the spectrum of pure PEO this band is absent. This may suggest that the interaction is occurring between the polymers. In the micrographs of the blends also observed change in their surfaces with variation of the composition of PMMA, contributing to the change of the electrical properties of the material. The EIS data showed that the material exhibited conductivity of the order of 10-6 S.cm-1. The blend in the ratio B2(85/15/0, 1) showed better conductivity, σ = 1.56 x 10-6 S.cm-1. It was observed that the diffusion coefficient for the blends, B5(70/30/0, 1) was the largest, 1.07 x 10-6 m2.s-1. The XRD data showing that, with the variation in the composition of the PMMA blend crystallinity of the material is decreased reaching a minimum B3(80/20/0,1), and then increases again. Thermal analysis suggests that blends made from the material obtained can be applied at room temperature