DESIGN OF AN EXPERIMENTAL TEST FACILITY FOR SUPERCRITICAL CO2 BRAYTON CYCLE

A supercritical CO2 test facility is currently being developed at Indian Institute of Science, Bangalore, India to analyze the performance of a closed loop Brayton cycle for concentrated solar power (CSP) generation. The loop has been designed for an external heat input of 20 kW a pressure range of 75-135 bar, flow rate of 11 kg/min, and a maximum cycle temperature of 525 degrees C. The operation of the loop and the various parametric tests planned to be performed are discussed in this paper The paper addresses various aspects of the loop design with emphasis on design of various components such as regenerator and expansion device. The regenerator design is critical due to sharp property variations in CO2 occurring during the heat exchange process between the hot and cold streams. Two types of heat exchanger configurations 1) tube-in-tube (TITHE) and 2) printed circuit heat exchanger (PCHE) are analyzed and compared. A PCHE is found to be similar to 5 times compact compared to a TITHE for identical heat transfer and pressure drops. The expansion device is being custom designed to achieve the desired pressure drop for a range of operating temperatures. It is found that capillary of 5.5 mm inner diameter and similar to 2 meter length is sufficient to achieve a pressure drop from 130 to 75 bar at a maximum cycle temperature of 525 degrees C.

Direct numerical test of the B-G-K model equation by the DSMC method

In the present paper the rarefied gas how caused by the sudden change of the wall temperature and the Rayleigh problem are simulated by the DSMC method which has been validated by experiments both in global flour field and velocity distribution function level. The comparison of the simulated results with the accurate numerical solutions of the B-G-K model equation shows that near equilibrium the BG-K equation with corrected collision frequency can give accurate result but as farther away from equilibrium the B-G-K equation is not accurate. This is for the first time that the error caused by the B-G-K model equation has been revealed.

Size Effect and Geometrical Effect of Polycrystals and Thin Film/Substrate System in Micro-indentation Test

Micro-indentation test at scales on the order of sub-micron has shown that the measured hardness increases strongly with decreasing indent depth or indent size, which is frequently referred to as the size effect. Simultaneously, at micron or sub-micron scale, the material microstructure size also has an important influence on the measured hardness. This kind of effect, such as the crystal grain size effect, thin film thickness effect, etc., is called the geometrical effect by here. In the present research, in order to investigate the size effect and the geometrical effect, the micro-indentation experiments are carried out respectively for single crystal copper and aluminum, for polycrystal aluminum, as well as for a thin film/substrate system, Ti/Si3N4. The size effect and geometrical effect are displayed experimentally. Moreover, using strain gradient plasticity theory, the size effect and the geometrical effect are simulated. Through comparing experimental results with simulation results, length-scale parameter appearing in the strain gradient theory for different cases is predicted. Furthermore, the size effect and the geometrical effect are interpreted using the geometrically necessary dislocation concept and the discrete dislocation theory. Member Price: $0; Non-Member Price: $25.00

Scour of the seabed under a pipeline in oscillating flow

The scour of the seabed under a pipeline is studied experimentally in this paper. Tests are carried out in a U-shaped oscillatory water tunnel with a box imbedded in the bottom of the test section. By use of the standard sand, clay and plastic grain as the seabed material, the influence of the bed material on the scour is studied. The relationship between the critical initial gap-to-diameter ratio above which no scour occurs and the parameters of the oscillating flow is obtained. The self-burial phenomenon. which occurs for the pipeline not fixed to two sidewalls of the test section, is not observed for the Bred pipeline. The effect of the pipe on sand wave formation is discussed. The maximum equilibrium scour depths For different initial gap-to-diameter ratios, different Kc numbers and different bed sands are also given in this paper.

Theory and Application of the Transient Injection Well Test

Based on the theory of the pumping well test, the transient injection well test was suggested in this paper. The design method and the scope of application are discussed in detail. The mathematical models are developed for the short-time and long-time transient injection test respectively. A double logarithm type curve matching method was introduced for analyzing the field transient injection test data. A set of methods for the transient injection test design, experiment performance and data analysis were established. Some field tests were analyzed, and the results show that the test model and method are suitable for the transient injection test and can be used to deal with the real engineering problems.

Diagnóstico comparativo de mastitis en leche bovina, por tres pruebas de campo: california mastitis test (CMT), acidez (NaOH), y reductasa, en los municipios de la Concordia, San Rafael del Norte y San Sebastián de Yali, Jinotega

Con el propósito de evaluar tres técnicas para la determinación de Mastitis, (California Mastitis Test (CMT), Hidróxido de Sodio (NaHO) y Azul de Metíleno (AM)), en vacas de doble propósito, en 2000 se efectuó un estudio en los municipios de La Concordia, San Rafael de Norte y San Sebastián de Yalí, del Departamento de Jinotega. Se utilizaron Fincas de Referencia atendidas por el entonces Ministerio de Agricultura y Ganadería (MAG), de las cuales se seleccionaron catorce (14) fincas privadas y dos Cooperativas, para un total de 16 fincas que representaron el 53.3 % del total de fincas. De éstas se muestrearon 398 vacas en producción de diversas razas (Pardo suizo, Brahman y cruces entre Pardo suizo, Criollo y Holstein con Cebú y otros) de diversas lactaciones (número parto}. Las muestras de cada cuarto de la vaca, se tomaron a la hora del ordeño, entre 5:00 y 7:00a.m. Los resultados de CMT e NaHO, (+ ó -), se anotaron en campo al momento de prueba. En la prueba de AM, se hicieron 4 lecturas: 1) al momento de prueba, 2) a los 15 minutos, 3) a una hora y, 4) a tres horas después de la prueba. Se obtuvo un total de 396 datos de 4 cuartos en cada técnica, para un total de 4,752 observaciones. La información se analizó mediante una prueba de Chí Cuadrado, con el Procedimiento CATMOD, del Statistical Análisis System (SAS), Versión para PC 6.03, NC. Las variables de clasificación en el análisis fueron Razas (1-3), Números de Parto (1-6) y Meses de lactación (1-9). De las técnicas, se obtuvo el 46.2, 4.6 y 15.3 % de pruebas positivas con CMT, NaOH y AM, respectivamente; la CMT resultó más efectiva en la determinación de mastitis. De las Razas estudiadas, el Brahmán presentó un 45.2% de afectación por mastitis, mayor que Pardo suizo y cruces indefinidos, con 30.6 y 24.2 %, respectivamente. A partir del tercer parto, se incrementa el nivel de infestación de esta enfermedad, y durante la lactación, en los meses 4, 5,8 y 9.

Comportamiento reproductivo, dinamica de produccion y calidad de la leche de genotipos lecheros bajo condiciones intensivas, en el tropico seco de Rivas, Nicaragua

Con el propósito de evaluar el comportamiento reproductivo, la dinámica de producción y calidad de la leche de genotipos lecheros en la Finca El Corpus del Meneo, manejado intensivamente, se utilizó información del periodo 1997 - 2004. Se analizaron 181 datos de edad de incorporación (EDADINC), 157 datos de edad a primer parto (EPP), 543 datos de número de servicios por concepción (NSC) y 341 datos de intervalo entre partos (IEP), 233 datos de dos pesajes de leche (diciembre 2004 y enero 2005) y sus respectivos análisis de calidad en porcentajes de grasa (%FAT), proteína (%PROT), lactosa (%LACT) y materia seca (%DRYM). Los modelos lineales aditivos incluyeron efectos de grupo racial (GRUPO), año de nacimiento (ANACV), año de incorporación (AINCV), época de incorporación (El), año de parto (APART), número de parto (NUMPA), época de parto (EP), periodo de lactancia (PERL) y sexo de la cría (SEXC) e interacciones importantes. Para EDINCV, se encontró diferencias relevantes entre GRUPOS (P<0.068), ANACV (P<0.0001), AINCV (P<0.0001) y EN (P<0.0001). Para EPP, diferencias importantes entre AINCV (P<0.0001), APART (P<0.0028) y la interacción APARTxEP (P<0.0361). Para NSC, diferencias estadísticas entre APART (P<0.0138) y NUMPA (P<0.0074). Para IEP, las diferencias importantes entre APART (P<0.0076), NUMPA (P<0.0004) y la interacción GRUPOxSEXC (P<0.0882). Se obtuvieron medias de mínimos cuadrados para EDADINC, EPP, NSC IEP de 25.75±0.72 meses, 35.71±0.88 meses, 1.34±0.11 unidades y !2.82±0.35 meses, respectivamente. Se encontró diferencias importantes entre GRUPOS (1'<0.0001 a P<0.026), NUMPA (P<0.0003 a P<0.0024), PERL (P<0.0000) y la interacción NUMPA*PERL (P<0.0000 a 0.0082), en las variables de producción y calidad, no así entre NUMPA para %DRYM. Se estimaron valores de 8.79±0.29 Kg., 4.14±0.09, 3.48±0.04, 4.31±0.02 y 12.56±0.11 para PLD, %FAT, %PROT, %LACT y %DRYM, respectivamente. GRUPOS no resulto significativo, pero se observo una tendencia marcada del GRUPO 5 (Pardo suizo) hacia una menor EDADINC, el GRUPO l (Holstein y cruces) mostró menores EPP, y los menores valores de NSC (mayor eficiencia técnica) e IEP para el GRUPO 3 (Jersey y cruces). El GRUPO con Holstein mostró mayores producciones de leche pero con menor calidad, mientras que los GRUPOS 2 y 4 (Jersey y cruces, Pardo suizo y cruces) mostraron menores producciones pero con mayor calidad general. La producción de leche por vaca promedio semanal (PLVD) a través de los años se comportó de acuerdo con algunos eventos climatológicos que determinan la disponibilidad y calidad del alimento. Se determinaron tres picos de producción (9.5, 10.0 y 9.7 kg.) y tres puntos críticos similares (9.0- 9.1 kg.). Los genotipos lecheros estudiados muestran que bajo condiciones de trópico seco y manejo intensivo es posible lograr parámetros de reproducción, producción y calidad de leche aceptable y mayores que los parámetros nacionales.

Nonuniformity Effect of Surface-Nanocrystalline Materials in Nanoindentation Test

In the present research, microstructures of the surface-nanocrystalline Al alloy material are observed and measured based on the transmission electron microscopy (TEM) technique, and the corresponding mechanical behaviors are investigated experimentally and theoretically. In the experimental research, the nanoindentation test method is used, and the load and microhardness curves are measured, which strongly depend on the grain size and grain size nonuniformity. Two kinds of the nanoindentation test methods are adopted: the randomly selected loading point method and the continuous stiffness method. In the theoretical modeling, based on the microstructure characteristics of the surface-nanocrystalline Al alloy material, a dislocation pile-up model considering the grain size effect and based on the Mott theory is presented and used. The hardness-indent depth curves are predicted and modeled.

The plastic collapse and energy absorption capacity of egg-box panels

The plastic collapse response of aluminium egg-box panels subjected to out-of-plane compression has been measured and modelled. It is observed that the collapse strength and energy absorption are sensitive to the level of in-plane constraint, with collapse dictated either by plastic buckling or by a travelling plastic knuckle mechanism. Drop weight tests have been performed at speeds of up to 6 m s-1, and an elevation in strength with impact velocity is noted. A 3D finite element shell model is needed in order to reproduce the observed behaviours. Additional calculations using an axisymmetric finite element model give the correct collapse modes but are less accurate than the more sophisticated 3D model. The finite element simulations suggest that the observed velocity dependence of strength is primarily due to strain-rate sensitivity of the aluminium sheet, with material inertia playing a negligible role. Finally, it is shown that the energy absorption capacity of the egg-box material is comparable to that of metallic foams. © 2003 Elsevier Ltd. All rights reserved.

Assessment of Microscale Test Methods of Peeling and Splitting along Surface of Thin-Film/Substrates

Peel test methods are assessed through being applied to a peeling analysis of the ductile film/ceramic substrate system. Through computing the fracture work of the system using the either beam bend model (BB model) or the general plane analysis model (GPA model), surprisingly, a big difference between both model results is found. Although the BB model can capture the plastic dissipation phenomenon for the ductile film case as the GPA model can, it is much sensitive to the choice of the peeling criterion parameters, and it overestimates the plastic bending effect unable to capture crack tip constraint plasticity. In view of the difficulty of measuring interfacial toughness using peel test method when film is the ductile material, a new test method, split test, is recommended and analyzed using the GPA model. The prediction is applied to a wedge-loaded experiment for Al-alloy double-cantilever beam in literature.

Deformation and Failure of Polymer Bonded Explosives under Diametric Compression Test

The tensile deformation and failure of polymer bonded explosives (PBXs), a particulate composite, is studied in this paper. Two HMX-based PBXs with different binder were selected for study. A diametric compression test, in which a disc-shaped specimen is loaded diametrically, was chosen to generate tensile failure in the materials. The quasi-static tensile properties and the tensile creep properties were studied by using conventional displacement transducers to measure the lateral strain along the horizontal diameter. The whole-field in-plane creep deformation was measured by using the technique of high resolution moire´ interferometry. Real time microscopic examination was conducted to monitor the process of deformation and failure of PBXs by using a scanning electron microscope equipped with a loading stage. A manifold method (MM) was used to simulate the deformation and failure of PBX samples under the diametric compression test, including the crack initiation, crack propagation and final cleavage fracture. The mechanisms of deformation and failure of PBXs under diametric compression were analyzed. The diametric compression test and the techniques developed in this research have proven to be applicable to the study of tensile properties of PBXs.

Efecto de labranza y metodos de control de malezas sobre la dinamica de las malezas y el crecimiento y rendimiento del frijol comum (Phaseolus vulgaris L.) Postrera 1995

Durante la postrera de 1995, se establecio un experimento de campo en la finca experimental La Compañia, localizada en San Marcos Carazo, con el propósito de evaluar los efectos de labranza y métodos de control de malezas sobre la dinámica de las malezas y el crecimiento y rendimiento del frijol común (Phaseolus vulgaris L.). Los tratamientos en estudio se evaluaron en un diseño de parcelas divididas con cuatro repeticiones. Los factores en estudio fueron A: sistemas de labranza (labranza cero, labranza mínima y labranza convencional). y B: controles de malezas (pre-emergente más postemergente, pre­ emergente más chapia,y pre-emergente más cobertura muerta de maíz (Zea mays L.). Los resultados indican que la especies de malezas dominantes fueron plantas de la familia Cyperaceae, sobresaliendo Cyperus rotundus L.y de la familia Poaceae: Digitaria sanguinalis (L). Scop, Ixophorus unisetus (Presl) Schlech,. De la clase dicotiledonea se identificaron Melantera aspera (Jacquin) de la familia Asterceae, Argemone mexicana L. de la familia Papaveraceae; y Chamaesyce hirta (L.) Mill de la familia Euphorbiaceae. Las especies descritas anteriormente fueron las de mayor abundancia y dominancia (cobertura y peso seco) en el área del experimento. Los mejores resultados se presentaron en la labranza mínima y manejo pre emergente más post emergente. De manera general se puede afirmar que los rendimientos presentaron diferencias altamente significativas en los sistemas de labranza. En cuanto al número de vainas por planta los mejores resultados los presenta labranza mínima. En relación al número de plantas por hectárea, el mayor número lo presenta labranza convencional. En referencia a peso de cien granos y rendimiento, los mejores resultados lo presenta labranza mínima. Los controles de maleza presentaron diferencias altamente significativas en la variable altura de plantas en el último recuento. Con referencia al número de vainas por planta, el mayor número lo presenta el control pre­ emergente más post emergente, en cuanto al rendimiento el de mayor valor fué el control pre-emergente más chapia. Las variables número de granos por vaina, peso de cien granos, y peso de paja, presentaron mejor comportamiento en el control pre-emergente más chapiac El sistema de labranza con mejor rentabilidad resultó ser el sistema de labranza mínima dado que este ofrece mayores beneficios netos con menores costos variables, además se obtuvieron los mejores rendimientos.