Nickel isotope fractionation during laterite Ni ore smelting and refining: implications for tracing the sources of Ni in smelter-affected soils

Nickel isotope ratios were measured in ores, fly ash, slags and FeNi samples from two metallurgical plants located in the Goiás State, Brazil (Barro Alto, Niquelândia). This allowed investigating the mass-dependent fractionation of Ni isotopes during the Ni-laterite ore smelting and refining. Feeding material exhibits a large range of δ60Ni values (from 0.02 ± 0.10 ‰ to 0.20 ± 0.05 ‰, n=7), explained by the diversity of Ni-bearing phases, and the average of δ60Nifeeding materials was found equal to 0.08 ± 0.08‰ (2SD, n=7). Both δ60Ni values of fly ash (δ60Ni = 0.07 ± 0.07‰, n=10) and final FeNi produced (0.05 ± 0.02 ‰, n=2) were not significantly different from the feeding materials ones. These values are consistent with the very high production yield of the factories. However, smelting slags present the heaviest δ60Ni values of all the smelter samples, with δ60Ni ranging from 0.11 ± 0.05 ‰ to 0.27 ± 0.05 ‰ (n=8). Soils were also collected near and far from the Niquelândia metallurgical plant, to evaluate the potential of Ni isotopes for tracing the natural vs anthropogenic Ni in soils. The Ni isotopic composition of the non-impacted topsoils developed on ultramafic rocks ranges from -0.26 ± 0.09 ‰ to -0.04 ± 0.05 ‰ (n=20). On the contrary, the Ni isotopic composition of the non-ultramafic topsoils, collected close to the plant, exhibit a large variation of δ60Ni, ranging from -0.19 ± 0.13 ‰ up to 0.10 ± 0.05 ‰ (n=4). This slight but significant enrichment in heavy isotopes highlight the potential impact of smelting activity in the surrounding area, as well as the potential of Ni isotopes for discerning anthropogenic samples (heavier δ60Ni values) from natural ones (lighter δ60Ni values). However, given the global range of published δ60Ni values (from -1.03 to 2.5 ‰) and more particularly those associated to natural weathering of ultramafic rocks (from -0.61 to 0.32‰), the use of Ni isotopes for tracing environmental contamination from smelters will remain challenging.

A contribution towards the performance and structural understanding of copper and nickel salts as ammonia stores

The ongoing depletion of fossil fuels and the severe consequences of the greenhouse effect make the development of alternative energy systems crucially important. While hydrogen is, in principle, a promising alternative, releasing nothing but energy and pure water. Hydrogen storage is complicated and no completely viable technique has been proposed so far. This work is concerned with the study of one potential alternative to pure hydrogen: ammonia, and more specifically its storage in solids. Ammonia, NH3, can be regarded as a chemical hydrogen carrier with the advantages of strongly reduced flammability and explosiveness as compared to hydrogen. Furthermore, ammine metal salts presented here as promising ammonia stores easily store up to 50 wt.-% ammonia, giving them a volumetric energy density comparable to natural gas. The model system NiX2–NH3 ( X = Cl, Br, I) is studied thoroughly with respect to ammine salt formation, thermal decomposition, air stability and structural effects. The system CuX2–NH3 ( X = Cl, Br) has an adverse thermal decomposition behaviour, making it impractical for use as an ammonia store. This system is, however, most interesting from a structural point of view and some work concerning the study of the structural behaviour of this system is presented. Finally, close chemical relatives to the metal ammine halides, the metal ammine nitrates are studied. They exhibit interesting anion arrangements, which is an impressive showcase for the combination of diffraction and spectroscopic information. The characterisation techniques in this thesis range from powder diffraction over single crystal diffraction, spectroscopy, computational modelling, thermal analyses to gravimetric uptake experiments. Further highlights are the structure solutions and refinements from powder data of (NH4)2[NiCl4(H2O)(NH3)] and Ni(NH3)2(NO3)2, the combination of crystallographic and chemical information for the elucidation of the (NH4)2[NiCl4(H2O)(NH3)] formation reaction and the growth of single crystals under ammonia flow, a technique allowing the first documented successful growth and single crystal diffraction measurement for [Cu(NH3)6]Cl2.

Filmes de nanopartículas de TiO2 e óxido de grafeno para fotocatálise

Dissertação (mestrado)—Universidade de Brasília, Instituto de Química, Programa de Pós-Graduação em Química, 2016.

I. Nickel-Exchanged Zincosilicate Catalysts for the Oligomerization of Propylene and II. Organic SDA-Free Catalysts for the Methanol-to-Olefins Reaction

Nickel-containing catalysts are developed to oligomerize light olefins. Two nickel-containing zincosilicates (Ni-CIT-6 and Ni-Zn-MCM-41) and two nickel-containing aluminosilicates (Ni-HiAl-BEA and Ni-USY) are synthesized as catalysts to oligomerize propylene into C_3n (C₆ and C₉) products. All catalysts oligomerize propylene, with the zincosilicates demonstrating higher average selectivities to C_3n products, likely due to the reduced acidity of the Zn heteroatom.

To test whether light alkanes can be incorporated into this oligomerization reaction, a supported homogeneous catalyst is combined with Ni-containing zincosilicates. The homogeneous catalyst is included to provide dehydrogenation/hydrogenation functions. When this tandem catalyst system is evaluated using a propylene/n-butane feed, no significant integration of alkanes are observed.

Ni-containing zincosilicates are reacted with 1-butene and an equimolar propylene/1-butene mixture to study other olefinic feeds. Further, other divalent metal cations such as Mn²⁺, Co²⁺, Cu²⁺, and Zn²⁺ are exchanged onto CIT-6 samples to investigate stability and potential use for other reactions. Co-CIT-6 oligomerizes propylene, albeit less effectively than Ni-CIT-6. The other M-CIT-6 samples, while not able to oligomerize light olefins, may be useful for other reactions, such as deNO_x.

Molecular sieves are synthesized, characterized, and used to catalyze the methanol-to-olefins (MTO) reaction. The Al concentration in SSZ-13 samples is varied to investigate the effect of Al number on MTO reactivity when compared to a SAPO-34 sample with only isolated Si Brønsted acid sites. These SSZ-13 samples display reduced transient selectivity behavior and extended reaction lifetimes as Si/Al increases; attributable to fewer paired Al sites. MTO reactivity for the higher Si/Al SSZ-13s resembles the SAPO-34 sample, suggesting that both catalysts owe their stable reaction behavior to isolated Brønsted acid sites.

Zeolites CHA and RHO are prepared without the use of organic structure-directing agents (OSDAs), dealuminated by steam treatments (500°C-800°C), and evaluated as catalysts for the MTO reaction. The effects of temperature and steam partial pressure during steaming are investigated. X-ray diffraction (XRD) and Ar physisorption show that steaming causes partial structural collapse of the zeolite, with degradation increasing with steaming temperature. ²⁷Al MAS NMR spectra of steamed materials reveal the presence of tetrahedral, pentacoordinate, and hexacoordinate aluminum.

Proton forms of as-synthesized CHA (Si/Al=2.4) and RHO (Si/Al=2.8) rapidly deactivate under MTO testing conditions (400°C, atmospheric pressure). CHA samples steamed at 600°C performed best among samples tested, showing increased olefin selectivities and catalyst lifetime. Acid washing these steamed samples further improved activity. Reaction results for RHO were similar to CHA, with the RHO sample steamed at 800°C producing the highest light olefin selectivities. Catalyst lifetime and C₂-C₃ olefin selectivities increase with increasing reaction temperature for both CHA-type and RHO-type steamed samples.

I. Synthetic Studies Toward the Total Synthesis of Polycyclic Natural Products – Communesin F, Perophoramidine and Ineleganolide. II. Nickel Catalyzed Intramolecular C–O Bond Formation

Expedient synthetic approaches to the highly functionalized polycyclic alkaloids communesin F and perophoramidine are described using a unified approach featuring a key decarboxylative allylic alkylation to access a crucial and highly congested 3,3-disubstituted oxindole. Described are two distinct, stereoselective alkylations that produce structures in divergent diastereomeric series possessing the critical vicinal all-carbon quaternary centers needed for each synthesis. Synthetic studies toward these challenging core structures have revealed a number of unanticipated modes of reactivity inherent to these complex alkaloid scaffolds. Finally, a previously unknown mild and efficient deprotection protocol for the o-nitrobenzyl group is disclosed – this serendipitous discovery permitted a concise endgame for the formal syntheses of both communesin F and perophoramidine.

In addition, the atroposelective synthesis of PINAP ligands has been accomplished via a palladium-catalyzed C–P coupling process through dynamic kinetic resolution. These catalytic conditions allow access to a wide variety of alkoxy- and benzyloxy-substituted PINAP ligands in high enantiomeric excess.

An efficient and exceptionally mild intramolecular nickel-catalyzed carbon–oxygen bond-forming reaction between vinyl halides and primary, secondary, and tertiary alcohols has been achieved. This operationally simple method allows direct access to cyclic vinyl ethers in high yields in a single step.

Finally, synthetic studies toward polycyclic ineleganolide are described. The entire fragmented carbon framework has been constructed from this work. Highly (Z)-selective olefination was achieved by the method by the Ando group.

Complexes cationiques POCOP de nickel : synthèse, caractérisation, réactivité et étude catalytique

Ce mémoire traite de la chimie des complexes pinceurs de nickel (II) cationiques ayant un ligand de type POCOP. Elle se divise en deux parties. La première traite de la synthèse, de la caractérisation et de la réactivité des complexes cationiques pinceurs de Ni(II) de type POCOP (POCOP = 1,3-bis(phosphinitobenzene), où C fait partie d’un cycle benzénique et est lié au métal, et P est un ligand phosphoré aussi lié au métal). Ces complexes ont un ligand acétonitrile coordonné au centre métallique et sont du type [(R-POCOPR’)Ni(NCMe)][OSO2CF3], où R est un substituant du cycle benzénique et R’ est un substituant sur le ligand phosphoré (R’ = iPr: R = H (1), p-Me(2), p-OMe(3), p-CO2Me(4), p-Br(5), m,m-tBu2(6), m-OMe(7), m-CO2Me(8); R’ = t-Bu : R = H (9), p-CO2Me(10)). Les complexes cationiques sont préparés en faisant réagir le dérivé Ni(II) neutre correspondant R-(POCOPR’)Ni-Br avec Ag(OSO2CF3¬) dans l’acétonitrile à température ambiante. L’impact des groupements R et R’ du ligand POCOP sur la structure et sur les propriétées électroniques du complexe a été étudié par spectroscopies RMN, UV-VIS et IR, analyse électrochimique, et diffraction des rayons X. Les valeurs de fréquence du lien C≡N (ν(C≡N)) augmentent avec le caractère électroattracteur du complexe, dans l’ordre 7 < 3 ~ 2 ~ 6 < 1 < 5 ~ 8 < 4 et 9 < 10. Ces résultats sont en accord avec le fait qu’une augmentation du caractère électrophile du centre métallique devrait résulter en une augmentation de la donation σ MeCN→Ni. De plus, les complexes cationiques montrent tous un potentiel d’oxydation Ni(II)/Ni(III) plus élevé que leurs analogues neutres Ni-Br. Ensuite, une étude d’équilibre entre un complexe neutre (R-POCOPR’)NiBr et un complexe cationique [(R-POCOPR’)Ni(NCMe)][OSO2CF3] démontre l’échange facile des ligands MeCN et Br. La deuxième partie de ce mémoire consiste en deux chapitres. Le premier (Chapitre 3) est une étude structurelle permettant une meilleure compréhension du mécanisme d’hydroamination des oléfines activées promue par les complexes présentés au chapitre 1, suivi de tentatives de synthèse de nouveaux composés POCOP cationiques comportant un ligand amine et nitrile, et de déplacement du groupement amine par un groupement nitrile. Le deuxième chapitre (4) décrit la réactivité et la cinétique de la réaction d’hydroamination et d’hydroalkoxylation d’oléfines activées, qui permet ainsi de mieux comprendre l’impact des différentes variables du système (groupements R et R’, température, substrats, solvent, etc.) sur la réactivité catalytique.

Complexes cationiques POCOP de nickel : synthèse, caractérisation, réactivité et étude catalytique

Ce mémoire traite de la chimie des complexes pinceurs de nickel (II) cationiques ayant un ligand de type POCOP. Elle se divise en deux parties. La première traite de la synthèse, de la caractérisation et de la réactivité des complexes cationiques pinceurs de Ni(II) de type POCOP (POCOP = 1,3-bis(phosphinitobenzene), où C fait partie d’un cycle benzénique et est lié au métal, et P est un ligand phosphoré aussi lié au métal). Ces complexes ont un ligand acétonitrile coordonné au centre métallique et sont du type [(R-POCOPR’)Ni(NCMe)][OSO2CF3], où R est un substituant du cycle benzénique et R’ est un substituant sur le ligand phosphoré (R’ = iPr: R = H (1), p-Me(2), p-OMe(3), p-CO2Me(4), p-Br(5), m,m-tBu2(6), m-OMe(7), m-CO2Me(8); R’ = t-Bu : R = H (9), p-CO2Me(10)). Les complexes cationiques sont préparés en faisant réagir le dérivé Ni(II) neutre correspondant R-(POCOPR’)Ni-Br avec Ag(OSO2CF3¬) dans l’acétonitrile à température ambiante. L’impact des groupements R et R’ du ligand POCOP sur la structure et sur les propriétées électroniques du complexe a été étudié par spectroscopies RMN, UV-VIS et IR, analyse électrochimique, et diffraction des rayons X. Les valeurs de fréquence du lien C≡N (ν(C≡N)) augmentent avec le caractère électroattracteur du complexe, dans l’ordre 7 < 3 ~ 2 ~ 6 < 1 < 5 ~ 8 < 4 et 9 < 10. Ces résultats sont en accord avec le fait qu’une augmentation du caractère électrophile du centre métallique devrait résulter en une augmentation de la donation σ MeCN→Ni. De plus, les complexes cationiques montrent tous un potentiel d’oxydation Ni(II)/Ni(III) plus élevé que leurs analogues neutres Ni-Br. Ensuite, une étude d’équilibre entre un complexe neutre (R-POCOPR’)NiBr et un complexe cationique [(R-POCOPR’)Ni(NCMe)][OSO2CF3] démontre l’échange facile des ligands MeCN et Br. La deuxième partie de ce mémoire consiste en deux chapitres. Le premier (Chapitre 3) est une étude structurelle permettant une meilleure compréhension du mécanisme d’hydroamination des oléfines activées promue par les complexes présentés au chapitre 1, suivi de tentatives de synthèse de nouveaux composés POCOP cationiques comportant un ligand amine et nitrile, et de déplacement du groupement amine par un groupement nitrile. Le deuxième chapitre (4) décrit la réactivité et la cinétique de la réaction d’hydroamination et d’hydroalkoxylation d’oléfines activées, qui permet ainsi de mieux comprendre l’impact des différentes variables du système (groupements R et R’, température, substrats, solvent, etc.) sur la réactivité catalytique.

Recovery of degraded areas due to nickel mining by using native species of Brazilian Savannah, Barro Alto, GO.

2016

Bis-Alkoxycarbonylation And Difunctionalization Of Alkenes Employing Palladium(II) Or Nickel(II) Complexes As Catalysts

Section 1 is focused on the bis-alkoxycarbonylation reaction of olefins, catalyzed by aryl α-diimine/Pd(II) complexes, for the synthesis of succinic acid ester derivatives, important compounds in many industrial fields. The opening chapter (Chapter 1) of this thesis presents an overview of the basic chemistry of organopalladium compounds and carbonylation reactions, focusing on oxidative bis-alkoxycarbonylation processes. In Chapter 2 the results obtained in the bis-alkoxycarbonylation of 1,2-disubstituted olefins are reported. The reaction proceeds under very mild reaction conditions, using an aryl α-diimine/Pd(II) catalyst and p-benzoquinone as oxidant, in the presence of a suitable alcohol. This process proved to be very efficient, selective and diastereospecific and various 2,3-disubstituted succinic esters have been obtained in high yields. In Chapter 3 the first bis-alkoxycarbonylation reaction of acrylic esters and acrylic amides, leading to the synthesis of 2-alkoxycarbonyl and 2-carbamoyl succinates respectively, is reported. Remarkably, the utilized aryl α-diimine/Pd(II) catalyst is able to promote the carbonylation of both the β- and the generally non-reactive α- positions of these alkenes. The proposed catalytic cycle is supported by DFT calculations. Section 2 is mainly focused on the Ni-catalyzed difunctionalization of unactivated alkenes tethered to unstabilized ketones. This reaction allows for a wide range of pharmaceutically useful cyclic architectures to be obtained. Chapter 4 consists of an introduction to the difunctionalization reactions of unactivated olefins. In particular, intramolecular reactions will be discussed in detail. In Chapter 5 the results obtained from the Ni-catalyzed difunctionalization of unactivated alkenes tethered to unstabilized ketones are reported. The reaction proceeds through the formation of a zinc-enolate compound, followed by a cyclization/cross-coupling reaction, which takes place in the presence of a phosphine/Ni(II) complex and an (hetero)aryl electrophile, leading to different cyclic and bicyilc architectures. In Chapter 6, preliminary results concerning the anionic cyclization of zinc enolates tethered to unactivated alkenes are presented.

Ossidazione elettrocatalitica di glucosio su schiume di nickel per la produzione selettiva di acido gluconico e acido glucarico

The selective electro-oxidation of D-glucose represents a promising way for the synthesis of many platform molecules, currently produced from non-renewable fossil fuels. Electrocatalysis is gaining considerable interest as an alternative to the thermochemical process, since it allows the process to be sustainable by operating at room temperature and pressure as well as using green solvents and electricity produced from renewable sources. In this work, the activity of three electrocatalysts, based on open cell Ni foams, towards the electrochemical oxidation of glucose to gluconic acid and glucaric acid was initially compared: a Ni bare foam, and Ni foams calcined at 500 °C for one hour and electrodeposited with Ni NP nanoparticles. The calcined foam turned out to be the most efficient. Then, the performance of this Ni calcined electrocatalyst was studied varying the reaction conditions, such as the potential applied (from 0,5V to 1,0V vs SCE), D-glucose concentration (0,01M, 0,05M and 0,10M) and NaOH concentration (0,10M and 1,0M). The activity of the electrocatalysts was evaluated in terms of glucose conversion, gluconic and gluconic acid selectivity and faradic efficiency. The best results were obtained over a Ni calcined foam with a 0,05M solution of D-glucose and 0,10M of NaOH at a 0,80V vs SCE potential.