Assessment of the effectiveness of light-emitting diode and diode laser hybrid light sources to intensify dental bleaching treatment

Objective. To evaluate the effectiveness of the color change of hybrid light-emitting diode (LED) and low-intensity infrared diode laser devices for activating dental bleaching and to verify the occurrence of a color regression with time. Material and methods. A total of 180 specimens obtained from human premolars were immersed in a coffee solution for 15 days for darkening and then divided into eight experimental groups (n = 20 in each) as follows: G1, bleaching without light; G2, bleaching with halogen light; G3, bleaching with a blue LED (1000 mW/470 nm) and a laser device (120 mW/795 nm) simultaneously; G4, bleaching with an LED emitting blue light (1000 mW/470 nm); G5, bleaching with a blue LED (800 mW/470 nm) and a laser device (500 mW/830 nm) simultaneously; G6, bleaching with a blue LED device (800 mW); G7, bleaching with a green LED (600 mW/530 nm) and a laser device (120 mW/795 nm) simultaneously; and G8, bleaching with a green LED (600 mW). Three measurements were performed (at baseline and 14 days and 12 months after bleaching) using a Vita Easyshade spectrophotometer. The data were submitted to two-way ANOVA and a Tukey test. Results. All groups showed significantly higher Delta E values than Group G1, with the exception of Group G8. Variations in the Delta E values at 14 days were significant when compared with those obtained at baseline and after 12 months. Conclusions. Light activation of the bleaching gel provided faster and more intense bleaching than use of the bleaching gel without light activation. Combinations of low-intensity diode lasers are ineffective as a bleaching gel activator. Color regression was observed after 12 months of storage.

Corrosion of the component phases presents in high copper dental amalgams. Application of electrochemical impedance spectroscopy and electrochemical noise analysis

The corrosion resistance of three of the constituent phases in high copper dental amalgams has been investigated by electrochemical methods in 0.9% NaCl solution. Polarization curves show corrosion potentials most positive for gamma(1)-Ag2Hg3, followed by Ag-Cu, and gamma-Ag3Sn in agreement with the order of corrosion resistance deduced from the corrosion currents. Complex plane impedance plots at the open circuit potential showed distorted semicircles with diffusional components at low frequency for Ag-Hg and Ag-Cu, while for gamma-Ag3Sn a layer of corrosion products is formed, partially or completely covering the surface of the electrode. Impedance and noise spectra have been compared in the frequency domain, and show good agreement. (C) 2004 Elsevier Ltd. All rights reserved.

Localization of the optimal solution and a posteriori bounds for aggregation

After an aggregated problem has been solved, it is often desirable to estimate the accuracy loss due to the fact that a simpler problem than the original one has been solved. One way of measuring this loss in accuracy is the difference in objective function values. To get the bounds for this difference, Zipkin (Operations Research 1980;28:406) has assumed, that a simple (knapsack-type) localization of an original optimal solution is known. Since then various extensions of Zipkin's bound have been proposed, but under the same assumption. A method to compute the bounds for variable aggregation for convex problems, based on general localization of the original solution is proposed. For some classes of the original problem it is shown how to construct the localization. Examples are given to illustrate the main constructions and a small numerical study is presented.

Electron scattering and effects of sources of light on photoconductivity of SnO2 coatings prepared by sol-gel

Electro-optical properties of sol-gel derived 2 mol% antimony or niobium doped tin dioxide films have been measured. The electron density has been calculated considering all the relevant scattering mechanisms and experimental conductivity data measured in the range -197 to 25 degrees C. The results support the hypothesis that both ionised impurity scattering and grain boundary scattering have comparable effects in the resistivity of coatings, for free electron density congruent to 5 x 10(18) cm(-3). We have measured variation of photoconductivity excitation with wavelength using xenon and deuterium lamp as light sources. Results show that the main band in the photoconductivity spectrum is dependent on the spectral light source emission, the excitation peak reaching 5 eV (deuterium lamp). This band is due to the recombination process involving oxygen species and photogenerated electron-hole pairs. (C) 1999 Elsevier B.V. B.V. All rights reserved.

Localization and irregular distribution of Na,K-ATPase in myelin sheath from rat sciatic nerve

Sodium, potassium adenosine triphosphatase (Na,K-ATPase) is a membrane-bound enzyme that maintains the Na+ and K+ gradients used in the nervous system for generation and transmission of bioelectricity. Recently, its activity has also been demonstrated during nerve regeneration. The present study was undertaken to investigate the ultrastructural localization and distribution of Na,K-ATPase in peripheral nerve fibers. Small blocks of the sciatic nerves of male Wistar rats weighing 250-300g were excised, divided into two groups, and incubated with and without substrate, the para-nitrophenyl phosphate (pNPP). The material was processed for transmission electron microscopy, and the ultra-thin sections were examined in a Philips CNI 100 (TM) electron microscope. The deposits of reaction product were localized mainly on the axolemma, on axoplasmic profiles, and irregularly dispersed on the myelin sheath, but not in the unmyelinated axons. In the axonal membrane, the precipitates were regularly distributed on the cytoplasmic side. These results together with published data warrant further studies for the diagnosis and treatment of neuropathies with compromised Na,K-ATPase activity. (c) 2007 Elsevier Ltd. All rights reserved.

Sources of atmospheric acidity in an agricultural-industrial region of São Paulo State, Brazil

[1] Surface-based measurements of atmospheric formic acid (HCOOH), acetic acid (CH3COOH), sulfur dioxide (SO2), hydrogen chloride (HCl), and nitric acid (HNO3) were made in central São Paulo State, Brazil, between April 1999 and March 2000. Mean concentrations were 9.0 ppb (HCOOH), 1.3 ppb (CH3COOH), 4.9 ppb (SO2), 0.3 ppb (HCl), and 0.5 ppb (HNO3). Concentrations in sugar cane burning plumes were 1160-4230 ppb (HCOOH), 360-1750 ppb (CH3COOH), 10-630 ppb (SO2), 4-210 ppb (HCl), and 14-90 ppb (HNO3). Higher ambient concentrations of SO2, HCl and HNO3 were measured during the burning season (May-November). Concentrations of SO2 and HCl increased during the evening, and of HCOOH and CH3COOH were lowest in the morning, with peak levels in the afternoon. Ratios obtained between different species showed either nighttime maxima (SO2/HCOOH, SO2/CH3COOH, SO2/HNO3, CH3COOH/HNO3, SO2/HCl and HCOOH/HNO3), daytime maxima (HCOOH/HCl, CH3COOH/HCl and HNO3/HCl), or no clear trends (HCOOH/CH3COOH). Correlation analysis showed that SO2 and HCl were primary emissions from biomass burning and road transport; HCOOH, HNO3 and CH3COOH were products of photochemistry; HCOOH and CH3COOH were emitted directly during combustion as well as from biogenic sources. Biomass burning affected atmospheric acidity on a regional scale, while vehicular emissions had greater impact in urban and adjacent areas. Atmospheric ammonia levels were insufficient to neutralize atmospheric acidity, which was mainly removed by deposition to the surface.

Influence of ambient gas on the growth and properties of porous tin-doped indium oxide thin films made by pulsed laser deposition

The laser ablation method was used for depositing porous nanocrystalline indium-tin oxide thin films for gas sensing applications. Samples were prepared at different pressures using three gases (O-2, 0.8N(2):0.2O(2), N-2) and heat-treated in the same atmosphere used for the ablation process. X-ray diffraction results show that the films are not oriented and the grain sizes are in the range between 15 and 40 nm. The grains are round shaped for all samples and the porosity of the films increases with the deposition pressure. The degree of sintering after heat treatment increases for lower oxygen concentrations, generating fractures on the surface of the samples. Film thicknesses are in the range of I pm for all gases as determined from scanning electron microscopy cross-sections. Electrical resistance varies between 36.3 ohm for the film made at 10 Pa pressure in N-2 until 9.35 x 10(7) ohm for the film made at 100 Pa in O-2. (C) 2007 Elsevier B.V. All rights reserved.

Inversion polymorphism in laboratory strains and natural samples of Drosophila sturtevanti (saltans group, sturtevanti subgroup)

Drosophila sturtevanti (37 strains) showed eighteen inversions, five new and thirteen previously described. Among these strains, 24 were maintained for seven to 21 years under laboratory conditions, eight for less than 1 year, and six were natural samples analysed in the first generation after collection. Flies from natural samples were the most polymorphic in the number of different inversions as well as in the frequency of flies bearing heterozygous inversions. In all cases, chromosome III presented the greatest number of inversions, and most of them occurred in strains from the Amazonian region. The data obtained were consistent with the hypothesis that the inversion variability of a species is proportional to the variability of its habitats.

Species diversity and seasonality of free-living ticks (Acari : Ixodidae) in the natural habitat of wild Marsh deer (Blastocerus dichotomus) in Southeastern Brazil

This study evaluated the presence and seasonal activity of free-living ticks in remaining marsh areas by the Parana river, in Brazil. Eight field trips (once per season) for collection of ticks were performed during 2 years. Using CO2 traps, dragging, and visual inspection of vegetation, five free-living tick species were collected, in the following order of abundance: Amblyomma cajennense, Amblyom\ma dubitatum, Amblyomma triste, Amblyomma coelebs, and Amblyomma nodosum. The seasonal pattern of A. cajennense was characterized by the highest peaks for adult ticks in the summer/spring months, for nymphs in the winter and for larvae in the autumn and winter. A. dubitatum and A. triste presented similar seasonal patterns characterized by peaks of adult ticks in the autumn. Nymphs of A. dubitatum peaked in the winter of the first year and in the winter/spring of the second year. A. triste was the only species to be collected in significantly higher numbers in the marsh than in surrounding drier areas such as forest patches. Among domestic animals living close the marsh areas, horses were infested by Anocentor nitens, A. cajennense, and Boophilus microplus, bovines were infested solely by B. microplus, and dogs were infested by Rhipicephalus sanguineus. Adults of A. triste showed to be well adapted to the marsh environment. This result, at least partially, explains local previous observations on the association of A. triste with marsh deer, as this vertebrate host inhabits mainly the marsh area. (c) 2006 Published by Elsevier B.V.

Chemical composition of flavonoids and styrylpyrones and the genetic variability of isozymes in natural populations of Cryptocarya mandioccana Meisner (Lauraceae)

The chemical composition of leaves of 57 trees of Cryptocarya mandioccana from three populations of southeastern Brazil was investigated through HPLC, assaying six flavonoids, seven styrylpyrones, and seven unidentified compounds. From 51 of the former trees, genotypes were obtained from 40 polymorphic loci of 19 isozymes. Cluster analyses of the phytochemical and genetical variation revealed that trees exhibited four chemotypes and five clusters from isozymes, respectively. Discriminant analyses from selected variables of the isozymic and chemical data sets were performed, respectively, in relation to the four chemotypes and the five isozyme clusters. The classification of individuals presented respective error estimates of 9.16% and 13.57%, indicating that the genetic data could explain the clusters from chernotypes and vice versa at acceptable error levels. Linear regressions with Dummy variable showed significant association of locus Skdh-2 with quercetin-3-O-beta-D-glucopyranoside and cryptofolione, indicating that its alleles would be responsible for the chemotype variation between individuals. (c) 2006 Elsevier Ltd. All rights reserved.

Natural History of the Lutz's Frog Cycloramphus lutzorum Heyer, 1983 (Anura: Cycloramphidae) in the Brazilian Atlantic Forest: Description of the Advertisement Call, Tadpole, and Karyotype

We describe the advertisement call, tadpole, karyotype, and additional information on the natural history of Cycloramphus lutzorum from southern Brazil. Sonograms were generated from digitally recorded calls. Tadpoles were collected in the field for description in the lab, and an adult was collected for karyotyping. Data on seasonal activity were gathered monthly from November 2005 to November 2007. All tadpoles (N = 21), juveniles (N = 18), and adults (N = 52) were found exclusively in streams. Reproduction, as identified by calling frogs, occurred from July through November. Frogs call all day long, but mostly at dusk, from rock crevices inside the stream edges near the splash zone. The call is short and loud, with 11 pulsed notes, of 491-641 ms, with a dominant frequency of 0.98-1.39 kHz. We describe the exotrophic and semiterrestrial tadpoles, always found in constantly humid vertical rock walls in the stream. Tadpoles of C. lutzorum are recognized by differences in labial tooth row formula, eye diameter, body shape, position of nares, and development of tail. Like congeneric species, the karyotype of C. lutzorum comprises 26 metacentric and submetacentric chromosomes. Cycloramphus lutzorum is restricted to and adapted for living in fast flowing streams, many of which are threatened by deforestation, pollution, and habitat loss. Therefore, we recommend the status of C. lutzorum be changed from its current "Data Deficient" to "Near Threatened (NT)" in the IUCN species red list.

Isolation and characterization of polymorphic microsatellites for the natural populations of barker frog Physalaemus cuvieri

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effects of ambient colour on colour preference and growth of juvenile rainbow trout Oncorhynchus mykiss (Walbaum)

Colour preference of individual juvenile rainbow trout Oncorhynchus mykiss was tested at 1 and 12 degrees C, and also at 12 degrees C after a 42 day growth experiment under white, blue, green, yellow or red ambient colour. All experiments were carried out under controlled laboratory conditions and the preference was assessed by the location of the fish in a preference tank with four chambers. Rainbow trout showed a preference for blue and green at 1 degrees C and for green at 12 degrees C. After the growth experiment the fish reared in blue tanks preferred blue and green but green was the most preferred colour for the fish reared in green, yellow and red tanks. Yellow and especially red chambers were avoided, irrespective of the ambient colour during the growth trial. The final mass of fish reared in the red aquaria was significantly smaller than that of the fish in green tanks. In addition, when the data of the preference tests were correlated with the data of the growth experiment using mean values of the four tested colours, a very good linear relationship was observed between the preference (i.e. visit frequency in coloured compartments) and growth rate as well as food intake. When considering the results both from the preference and growth trials it is suggested that green is the best environmental colour for rearing juvenile rainbow trout while rearing in a red environment cannot be recommended. (c) 2008 The Authors Journal compilation (c) 2008 The Fisheries Society of the British Isles.