Deproteinized bovine bone mineral particles and osseointegration of implants without primary bone contact: An experimental study in dogs

Objectives: To evaluate the influence on osseointegration of Deproteinized bovine bone mineral (DBBM) particles used to fill defects of at least 1 mm around implants having no primary contact with bone. Material and methods: Premolars and first molars were extracted bilaterally from the mandible of six Labrador dogs. After 3 months of healing, mucoperiosteal full-thickness flaps were elevated, and one recipient site was prepared in the molar region of each hemi-mandible to place implants. These were installed with a deliberate circumferential and periapical space to the bone walls of 1.2 mm. All implants were stabilized with passive fixation plates to maintain the implants in situ and without any contact with the implant bed. The control sites were left to be filled with coagulum, while at the test sites, the residual gap was filled with DBBM. After 3 months of submerged healing, the animals were sacrificed. Ground sections were prepared and analyzed histomorphometrically. Results: Mineralized bone-to-implant contact was 4.0% and 3.9% for control and test sites, respectively. The width of the residual defects was 0.48 mm and 0.88 mm at the control and test sites, respectively. The percentage of implant surface covered by a layer of dense connective tissue of 0.12 mm of width on average was 84.9% and 88.5% at the control and test sites, respectively. Conclusion: A minor and not predictable degree of contact or distance osteogenesis was obtained on the implant surface when primary contact of the implant surface with the implant bed had deliberately been avoided. DBBM grafting of the artificial gap did not favor osseointegration. Neither did it enhance the ability to bridge the gap with newly formed bone in an artificial defect wider than 1 mm. © 2013 John Wiley & Sons A/S.

Small particles in Pluto's environment: Effects of the solar radiation pressure

Impacts of micrometeoroids on the surfaces of the plutonian small satellites Nix and Hydra can generate dust particles. Even in this region so far from the Sun these tiny ejected particles are under the effects of the solar radiation pressure. In this work, we investigate the orbital evolution of the escaping ejecta from both the small satellites under the effects of the radiation pressure combined with the gravitational effects of Pluto, Charon, Nix and Hydra. The mass production rate of micron-sized dust particles generated by micrometeoroids hitting the satellites is obtained, and numerical simulations are performed to derive the lifetime of the ejecta. These pieces of information allow us to estimate the optical depth of a putative ring, which extends from the orbits of Nix to Hydra. The ejected particles, between the orbits of Nix and Hydra, form a wide ring of about 16 000 km. Collisions with the massive bodies and escape from the system are mainly determined by the effects of the solar radiation pressure. This is an important loss mechanism, removing 30 per cent of the initial set of 1 μm-sized particles in 1 yr. The surviving particles form a ring too faint to be detectable with the derived maximum optical depth of 4 × 10-11. © 2013 The Authors Published by Oxford University Press on behalf of the Royal Astronomical Society.

Search for fractionally charged particles in pp collisions at √s=7 TeV

A search is presented for free heavy long-lived fractionally charged particles produced in pp collisions at √s=7 TeV. The data sample was recorded by the CMS detector at the LHC and corresponds to an integrated luminosity of 5.0 fb-1. Candidate fractionally charged particles are identified by selecting tracks with associated low charge measurements in the silicon tracking detector. Observations are found to be consistent with expectations for background processes. The results of the search are used to set upper limits on the cross section for pair production of fractionally charged, massive spin-1/2 particles that are neutral under SU(3)C and SU(2)L. We exclude at 95% confidence level such particles with electric charge ±2e/3 with masses below 310 GeV, and those with charge ±e/3 with masses below 140 GeV. © 2013 CERN. Published by the American Physical Society under the terms of the http://creativecommons.org/ licenses/by/3.0/Creative Commons Attribution 3.0 License. Further distribution of this work must maintain attribution to the author(s) and the published article's title, journal citation, and DOI.

Searches for long-lived charged particles in pp collisions at □ =7 and 8 TeV

Abstract: Results of searches for heavy stable charged particles produced in pp collisions at □ = 7 and 8 TeV are presented corresponding to an integrated luminosity of 5.0 fb-1 and 18.8 fb-1, respectively. Data collected with the CMS detector are used to study the momentum, energy deposition, and time-of-flight of signal candidates. Leptons with an electric charge between e/3 and 8e, as well as bound states that can undergo charge exchange with the detector material, are studied. Analysis results are presented for various combinations of signatures in the inner tracker only, inner tracker and muon detector, and muon detector only. Detector signatures utilized are long time-of-flight to the outer muon system and anomalously high (or low) energy deposition in the inner tracker. The data are consistent with the expected background, and upper limits are set on the production cross section of long-lived gluinos, scalar top quarks, and scalar τ leptons, as well as pair produced long-lived leptons. Corresponding lower mass limits, ranging up to 1322 GeV/c 2 for gluinos, are the most stringent to date. [Figure not available: see fulltext.] © 2013 Cern for the benefit of the CMS collaboration.

Corrosion and tribocorrosion behaviour of Al-Si-Cu-Mg alloy and its composites reinforced with B4C particles in 0.05M NaCl solution

The corrosion behaviour of metal matrix composites (MMCs) is strictly linked with the presence of heterogeneities such as reinforcement phase, microcrevices, porosity, secondary phase precipitates, and interaction products. Most of the literature related to corrosion behaviour of aluminium matrix composites (AMCs) is focused on SiC reinforced AMCs. On the other hand, there is very limited information available in the literature related to the tribocorrosion behaviour of AMCs. Therefore, the present work aims to investigate corrosion and tribocorrosion behaviour of Al-Si-Cu-Mg alloy matrix composites reinforced with B4C particulates. Corrosion behaviour of 15 and 19% (vol) B4C reinforced Al-Si-Cu-Mg matrix composites and the base alloy was investigated in 0.05M NaCl solution by performing immersion tests and potentiodynamic polarisation tests. Tribocorrosion behaviour of Al-Si-Cu-Mg alloy and its composites were also investigated in 0.05M NaCl solution. The tests were carried out against alumina ball using a reciprocating ball-on-plate tribometer. Electrochemical measurements were performed before, during, and after the sliding tests together with the recording of the tangential force. Results suggest that particle addition did not affect significantly the tendency of corrosion of Al-Si-Cu-Mg alloy without mechanical interactions. During the tribocorrosion tests, the counter material was found to slide mainly on the B4C particles, which protected the matrix alloy from severe wear damage. Furthermore, the wear debris were accumulated on the worn surfaces and entrapped between the reinforcing particles. Therefore, the tendency of corrosion and the corrosion rate decreased in Al-Si-Cu-Mg matrix B4C reinforced composites during the sliding in 0.05M NaCl solution. © 2013 Elsevier B.V.

Search in leptonic channels for heavy resonances decaying to long-lived neutral particles

A search is performed for heavy resonances decaying to two long-lived massive neutral particles, each decaying to leptons. The experimental signature is a distinctive topology consisting of a pair of oppositely charged leptons originating at a separated secondary vertex. Events were collected by the CMS detector at the LHC during pp collisions at √s = 7 TeV, and selected from data samples corresponding to 4.1 (5.1) fb-1 of integrated luminosity in the electron (muon) channel. No significant excess is observed above standard model expectations, and an upper limit is set with 95% confidence level on the production cross section times the branching fraction to leptons, as a function of the long-lived massive neutral particle lifetime. Copyright CERN.

Dynamical properties for an ensemble of classical particles moving in a driven potential well with different time perturbation

We consider dynamical properties for an ensemble of classical particles confined to an infinite box of potential and containing a time-dependent potential well described by different nonlinear functions. For smooth functions, the phase space contains chaotic trajectories, periodic islands and invariant spanning curves preventing the unlimited particle diffusion along the energy axis. Average properties of the chaotic sea are characterised as a function of the control parameters and exponents describing their behaviour show no dependence on the perturbation functions. Given invariant spanning curves are present in the phase space, a sticky region was observed and show to modify locally the diffusion of the particles. © 2013 Elsevier B.V.

Síntese e caracterização de nanoesferas de sílica monodispersas para obtenção de filmes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo de degradação térmica e caracterização de lodos provenientes de diferentes sistemas de tratamento de esgotos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Propriedades ópticas em filmes de opalas sintéticas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Preparação pelo processo sol-gel de pós redispersáveis, filmes finos densos e materiais mesoporosos de óxido de titânio

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Ocorrência de rotavírus do grupo D em aves criadas em granjas na mesorregião metropolitana de Belém, Pará

Os rotavírus infectam seres humanos e várias espécies de animais e são constituídos por partículas icosaédricas, não envelopadas, formadas por um genoma de 11 segmentos de dsRNA. São classificados em sete grupos designados de A-G. O rotavírus do grupo D (RVs-D) tem sido documentado em aves, porém existem poucos estudos disponíveis, principalmente com dados de detecção por RT-PCR e obtenção de sequências nucleotídicas. Este estudo objetivou investigar a ocorrência de RVs-D em aves criadas em granjas situadas na Mesorregião Metropolitana de Belém- Pará, no período compreendido entre 2008 a 2011. Foram colhidos 85 pools de amostras fecais provenientes de 37 granjas pertencentes a oito municípios da Mesorregião Metropolitana de Belém. O dsRNA viral foi extraído a partir das suspensões fecais e submetido à eletroforese em gel de poliacrilamida (EGPA) seguido da RT-PCR realizada a partir da construção de iniciadores específicos para os genes VP6 e VP7 do RVs-D. Foi selecionada uma amostra positiva de cada município para o sequenciamento de nucleotídeos dos genes VP6 e VP7, sendo cinco amostras clonadas. A EGPA demonstrou positividade em 14/85 (16,5%) amostras e a RT-PCR em 30/85 (35,3%) amostras. Dos oito municípios estudados, sete apresentaram amostras positivas para RVs-D. Dentre as 37 granjas pertencentes a esses municípios foi observado a presença dessa infecção viral em 17 (45,9%) das granjas estudadas. O intervalo de idade em que o RVs-D foi detectado com maior frequência foi o de aves entre 16 a 30 dias (23/37 – 62%) do total de amostras nesta faixa etária. As sequências nucleotídicas das sete amostras foram classificadas como pertencentes ao RVs-D com bootstrap de 100 corroborando com esse agrupamento. As sequências do gene VP6 apresentaram 90,8-91,3% de similaridade com o protótipo de RVs-D (05V0049) e 98,5-99,9% de similaridade quando comparadas entre si. Para o gene VP7 apresentaram 87-96,1% de similaridade com o protótipo deste grupo e foram 94,1-100% similares quando comparados entre si. A presente análise assume um caráter pioneiro no Brasil e no mundo, permitindo ampliar os conhecimentos acerca do RVs-D.

Influência da granulometria e de aditivos no comportamento reológico do rejeito de lavagem da bauxita

Na mineração da bauxita no município de Paragominas-PA, são descartados no processo de beneficiamento rejeitos com teor de sólido de 33,5 % e granulometria muito fina com D₅₀ abaixo de 5 μm. Esses fatores contribuem para que esta suspensão formada basicamente por silico aluminatos, com elevada concentração de argila caulinita, apresente alta viscosidade e alta tensão inicial de escoamento. Foi realizada análise granulométrica e determinadas as composições químicas e mineralógicas do material. A análise granulométrica foi feita por peneiramento a úmido e as frações finas foram determinadas pela técnica da difração a laser. A determinação da composição química foi feita por Espectrometria de Fluorescência de Raios-X, obtendo-se considerável teor de alumina aproveitável, 21, 28%. A composição mineralógica foi determinada por Difração de Raios-X (DRX), obtendo-se gibsita, hematita, quartzo e caulinita. Realizou-se a determinação dos fatores de atrito da polpa, utilizando equação para fluidos que seguem o modelo de Herschel-Bulkley e utilizando as correlações de Dodge e Metzner. Utilizou-se o viscosímetro VT550, com sensor tipo cilindros coaxiais SV1, para realizar testes de defloculação e floculação utilizando diferentes aditivos reológicos. Os aditivos utilizados foram: hexametafosfato de sódio, hidroxamato, sulfato de alumínio, poliacrilato de sódio e poliacrilamida 25% aniônica. A programação foi taxa de cisalhamento de 100 s^-1, tempo de 20s e temperatura de 32ºC. Os defloculantes podem ser utilizados para melhorar o processo de bombeamento e os floculantes podem ser utilizados como auxiliadores no processo de sedimentação nos espessadores, auxiliando no processo de separação sólido-líquido. Foram realizadas ainda, análises de viscosidade em polpas com diferentes pH e em amostras passante a 400# Tyler, com o objetivo de avaliar se a granulometria e o pH influenciavam no comportamento dos aditivos. Pelo estudo observou-se que a granulometria e o pH influenciam no comportamento dos aditivos, pois quanto menor a granulometria mais eficiente é a atuação do aditivo e o seu comportamento como floculante ou defloculante está condicionado ao ajuste do pH.

Síntese e caracterização de novos materiais compósitos orgânicos/inorgânicos, fotopolimerizáveis, para uso em restaurações odontológicas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Search for long-lived particles in events with photons and missing energy in proton-proton collisions at root s=7 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)