Ultra-low power WSNs: distributed signal processing and dynamic resource management

This thesis presents several data processing and compression techniques capable of addressing the strict requirements of wireless sensor networks. After introducing a general overview of sensor networks, the energy problem is introduced, dividing the different energy reduction approaches according to the different subsystem they try to optimize. To manage the complexity brought by these techniques, a quick overview of the most common middlewares for WSNs is given, describing in detail SPINE2, a framework for data processing in the node environment. The focus is then shifted on the in-network aggregation techniques, used to reduce data sent by the network nodes trying to prolong the network lifetime as long as possible. Among the several techniques, the most promising approach is the Compressive Sensing (CS). To investigate this technique, a practical implementation of the algorithm is compared against a simpler aggregation scheme, deriving a mixed algorithm able to successfully reduce the power consumption. The analysis moves from compression implemented on single nodes to CS for signal ensembles, trying to exploit the correlations among sensors and nodes to improve compression and reconstruction quality. The two main techniques for signal ensembles, Distributed CS (DCS) and Kronecker CS (KCS), are introduced and compared against a common set of data gathered by real deployments. The best trade-off between reconstruction quality and power consumption is then investigated. The usage of CS is also addressed when the signal of interest is sampled at a Sub-Nyquist rate, evaluating the reconstruction performance. Finally the group sparsity CS (GS-CS) is compared to another well-known technique for reconstruction of signals from an highly sub-sampled version. These two frameworks are compared again against a real data-set and an insightful analysis of the trade-off between reconstruction quality and lifetime is given.

Modelling and Design of Advanced Reliable Circuits and Devices for Energy Efficiency

Reliable electronic systems, namely a set of reliable electronic devices connected to each other and working correctly together for the same functionality, represent an essential ingredient for the large-scale commercial implementation of any technological advancement. Microelectronics technologies and new powerful integrated circuits provide noticeable improvements in performance and cost-effectiveness, and allow introducing electronic systems in increasingly diversified contexts. On the other hand, opening of new fields of application leads to new, unexplored reliability issues. The development of semiconductor device and electrical models (such as the well known SPICE models) able to describe the electrical behavior of devices and circuits, is a useful means to simulate and analyze the functionality of new electronic architectures and new technologies. Moreover, it represents an effective way to point out the reliability issues due to the employment of advanced electronic systems in new application contexts. In this thesis modeling and design of both advanced reliable circuits for general-purpose applications and devices for energy efficiency are considered. More in details, the following activities have been carried out: first, reliability issues in terms of security of standard communication protocols in wireless sensor networks are discussed. A new communication protocol is introduced, allows increasing the network security. Second, a novel scheme for the on-die measurement of either clock jitter or process parameter variations is proposed. The developed scheme can be used for an evaluation of both jitter and process parameter variations at low costs. Then, reliability issues in the field of “energy scavenging systems” have been analyzed. An accurate analysis and modeling of the effects of faults affecting circuit for energy harvesting from mechanical vibrations is performed. Finally, the problem of modeling the electrical and thermal behavior of photovoltaic (PV) cells under hot-spot condition is addressed with the development of an electrical and thermal model.

On the accuracy of Software-based Energy Estimation Techniques

This paper examines the accuracy of software-based on-line energy estimation techniques. It evaluates today’s most widespread energy estimation model in order to investigate whether the current methodology of pure software-based energy estimation running on a sensor node itself can indeed reliably and accurately determine its energy consumption - independent of the particular node instance, the traffic load the node is exposed to, or the MAC protocol the node is running. The paper enhances today’s widely used energy estimation model by integrating radio transceiver switches into the model, and proposes a methodology to find the optimal estimation model parameters. It proves by statistical validation with experimental data that the proposed model enhancement and parameter calibration methodology significantly increases the estimation accuracy.

Demo Abstract: Disseminating WMSN Data by Using Social Network and Web

For smart cities applications, a key requirement is to disseminate data collected from both scalar and multimedia wireless sensor networks to thousands of end-users. Furthermore, the information must be delivered to non-specialist users in a simple, intuitive and transparent manner. In this context, we present Sensor4Cities, a user-friendly tool that enables data dissemination to large audiences, by using using social networks, or/and web pages. The user can request and receive monitored information by using social networks, e.g., Twitter and Facebook, due to their popularity, user-friendly interfaces and easy dissemination. Additionally, the user can collect or share information from smart cities services, by using web pages, which also include a mobile version for smartphones. Finally, the tool could be configured to periodically monitor the environmental conditions, specific behaviors or abnormal events, and notify users in an asynchronous manner. Sensor4Cities improves the data delivery for individuals or groups of users of smart cities applications and encourages the development of new user-friendly services.

A Routing Protocol Based on Energy and Link Quality for Internet of Things Applications

The Internet of Things (IoT) is attracting considerable attention from the universities, industries, citizens and governments for applications, such as healthcare, environmental monitoring and smart buildings. IoT enables network connectivity between smart devices at all times, everywhere, and about everything. In this context, Wireless Sensor Networks (WSNs) play an important role in increasing the ubiquity of networks with smart devices that are low-cost and easy to deploy. However, sensor nodes are restricted in terms of energy, processing and memory. Additionally, low-power radios are very sensitive to noise, interference and multipath distortions. In this context, this article proposes a routing protocol based on Routing by Energy and Link quality (REL) for IoT applications. To increase reliability and energy-efficiency, REL selects routes on the basis of a proposed end-to-end link quality estimator mechanism, residual energy and hop count. Furthermore, REL proposes an event-driven mechanism to provide load balancing and avoid the premature energy depletion of nodes/networks. Performance evaluations were carried out using simulation and testbed experiments to show the impact and benefits of REL in small and large-scale networks. The results show that REL increases the network lifetime and services availability, as well as the quality of service of IoT applications. It also provides an even distribution of scarce network resources and reduces the packet loss rate, compared with the performance of well-known protocols.

Monitoreo de condiciones de higiene y seguridad del ambiente en entornos industriales usando redes de sensores inalámbricos

Resumen: Las redes de sensores inalámbricos han atraído mucha atención en los últimos años debido a la integración de tecnología inalámbrica, computación y tecnología de sensores. Estas redes consisten en una serie de nodos equipados con capacidades de procesamiento, comunicación y sensado. Utilizan protocolos especiales de radio para transmitir datos en un modo multisalto de operación. En este trabajo se propone utilizar una red de sensores para el monitoreo de las condiciones ambientales de Higiene y Seguridad en entornos industriales. Concretamente se monitorean Temperatura, Humedad, Ruido y Luminosidad. Se propone esta recolección de datos para dar soporte a la inspección anual de un auditor externo, por lo que no se considera esta recolección como crítica dado que no controlan ningún dispositivo. En primera instancia se aborda el problema utilizando una red de sensores con módulos que utilizan el protocolo 802.15 los cuales transmiten a un nodo maestro que sirve como gateway para enviar la información a un servidor que la almacena. La recolección de datos se realiza a través de una plataforma arduino como interface entre el módulo inalámbrico y los sensores. Esta primera propuesta es contrastada con un enfoque de Internet de las Cosas (IoT) utilizando módulos Arduino con WiFi embebido, denominados Wido, que permiten la comunicación de datos directamente al servidor de almacenaje. El trabajo comprende la caracterización del problema, elección del hardware, diseño de la red y la realización de pruebas para evaluar el funcionamiento de ambos enfoques.

Intrusion-Resilient Integrity in Data-Centric Unattended WSNs

Unattended Wireless Sensor Networks (UWSNs) operate in autonomous or disconnected mode: sensed data is collected periodically by an itinerant sink. Between successive sink visits, sensor-collected data is subject to some unique vulnerabilities. In particular, while the network is unattended, a mobile adversary (capable of subverting up to a fraction of sensors at a time) can migrate between compromised sets of sensors and inject fraudulent data. In this paper, we provide two collaborative authentication techniques that allow an UWSN to maintain integrity and authenticity of sensor data-in the presence of a mobile adversary-until the next sink visit. Proposed schemes use simple, standard, and inexpensive symmetric cryptographic primitives, coupled with key evolution and few message exchanges. We study their security and effectiveness, both analytically and via simulations. We also assess their robustness and show how to achieve the desired trade-off between performance and security.

PEPSI: Privacy-Enhanced Participatory Sensing Infrastructure.

Participatory Sensing combines the ubiquity of mobile phones with sensing capabilities of Wireless Sensor Networks. It targets pervasive collection of information, e.g., temperature, traffic conditions, or health-related data. As users produce measurements from their mobile devices, voluntary participation becomes essential. However, a number of privacy concerns -- due to the personal information conveyed by data reports -- hinder large-scale deployment of participatory sensing applications. Prior work on privacy protection, for participatory sensing, has often relayed on unrealistic assumptions and with no provably-secure guarantees. The goal of this project is to introduce PEPSI: a Privacy-Enhanced Participatory Sensing Infrastructure. We explore realistic architectural assumptions and a minimal set of (formal) privacy requirements, aiming at protecting privacy of both data producers and consumers. We design a solution that attains privacy guarantees with provable security at very low additional computational cost and almost no extra communication overhead.

Redes y servicios ubicuos para Internet de las Cosas en dispositivos llevables

En las últimas décadas se han producido importantes avances tecnológicos, lo que ha producido un crecimiento importante de las Redes Inalámbricas de Sensores (RIS), conocidas en inglés como Wireless Sensor Networks (WSN). Estas redes están formadas por un conjunto de pequeños nodos o también, conocidos como motas, compuestos por diversos tipos de sensores. Las Redes Inalámbricas de Sensores pueden resultar muy útiles en entornos donde el despliegue de redes cableadas, formadas por ordenadores, encaminadores u otros dispositivos de red no sea posible. Sin embargo, este tipo de redes presentan una serie de carencias o problemas que dificultan, en ocasiones, su implementación y despliegue. Este Proyecto Fin de Carrera tiene como principales objetivos: diseñar e implementar un agente que haga uso de la tecnología Bluetooth para que se pueda comunicar tanto con la arquitectura orientada a servicios, vía radio, como con el módulo Bioharness para obtener parámetros fisiológicos; ofrecer una serie de servicios simples a la Red Inalámbrica de Sensores; diseñar un algoritmo para un sistema de alarmas; realizar e implementar una pasarela entre protocolos que usen el estándar IEEE802.15.4 (ZigBee) y el estándar IEEE802.15.1 de la Tecnología Bluetooth. Por último, implementar una aplicación Android para el reloj WiMM y que este pueda recibir alarmas en tiempo real a través del la Interfaz Bluetooth. Para lograr estos objetivos, en primer lugar realizaremos un estudio del Estado del Arte de las Redes Inalámbricas de Sensores, con el fin de estudiar su arquitectura, el estándar Bluetooth y los dispositivos Bluetooth que se han utilizado en este Proyecto. Seguidamente, describiremos detalladamente el firmware iWRAP versión 4, centrándonos en sus modos de operación, comandos AT y posibles errores que puedan ocurrir. A continuación, se describirá la arquitectura y la especificación nSOM, para adentrarnos en la arquitectura orientada a servicios. Por último, ejecutaremos la fase de validación del sistema y se analizarán los resultados obtenidos durante la fase de pruebas. ABSTRACT In last decades there have been significant advances in technology, which has resulted in important growth of Wireless Sensor Networks (WSN). These networks consist of a small set of nodes, also known as spots; equipped with various types of sensors. Wireless Sensor Networks can be very useful in environments where deployment of wired networks, formed by computers, routers or other network devices is not possible. However, these networks have a number of shortcomings or challenges to, sometimes, their implementation and deployment. The main objectives of this Final Project are to design and implement an agent that makes use of Bluetooth technology so you can communicate with both the service-oriented architecture, via radio, as with Bioharness module for physiological parameters; offer simple services to Wireless Sensor Network, designing an algorithm for an alarm system, make and implement a gateway between protocols using the standard IEEE802.15.4 (ZigBee) and IEEE802.15.1 standard Bluetooth Technology. Finally, implement an Android application for WiMM watch that can receive real-time alerts through the Bluetooth interface. In order to achieve these objectives, firstly we are going to carry out a study of the State of the Art in Wireless Sensor Network, where we study the architecture, the Bluetooth standard and Bluetooth devices that have been used in this project. Then, we will describe in detail the iWRAP firmware version 4, focusing on their operation modes, AT commands and errors that may occur. Therefore, we will describe the architecture and specification nSOM, to enter into the service-oriented architecture. Finally, we will execute the phase of validation of the system in a real application scenario, analyzing the results obtained during the testing phase.

Distributed target tracking based on belief propagation consensus

Distributed target tracking in wireless sensor networks (WSN) is an important problem, in which agreement on the target state can be achieved using conventional consensus methods, which take long to converge. We propose distributed particle filtering based on belief propagation (DPF-BP) consensus, a fast method for target tracking. According to our simulations, DPF-BP provides better performance than DPF based on standard belief consensus (DPF-SBC) in terms of disagreement in the network. However, in terms of root-mean square error, it can outperform DPF-SBC only for a specific number of consensus iterations.

Power management techniques in an FPGA-Based WSN node for high performance application

In this work, the power management techniques implemented in a high-performance node for Wireless Sensor Networks (WSN) based on a RAM-based FPGA are presented. This new node custom architecture is intended for high-end WSN applications that include complex sensor management like video cameras, high compute demanding tasks such as image encoding or robust encryption, and/or higher data bandwidth needs. In the case of these complex processing tasks, yet maintaining low power design requirements, it can be shown that the combination of different techniques such as extensive HW algorithm mapping, smart management of power islands to selectively switch on and off components, smart and low-energy partial reconfiguration, an adequate set of save energy modes and wake up options, all combined, may yield energy results that may compete and improve energy usage of typical low power microcontrollers used in many WSN node architectures. Actually, results show that higher complexity tasks are in favor of HW based platforms, while the flexibility achieved by dynamic and partial reconfiguration techniques could be comparable to SW based solutions.

Simulador WKM para gestión de conocimiento en una WSN

La gestión del conocimiento (KM) se basa en la captación, filtración, procesamiento y análisis de unos datos en bruto que con dicho refinamiento podrán llegar a convertirse en conocimiento o Sabiduría. Estas prácticas tendrán lugar en este PFC en una WSN (Wireless Sensor Network) compuesta de unos sofisticados dispositivos comúnmente conocidos como “motas” y cuya principal característica son sus bajas capacidades en cuanto a memoria, batería o autonomía. Ha sido objetivo primordial de este Proyecto de fin de Carrera aunar una WSN con la Gestión del Conocimiento así como demostrar que es posible llevar a cabo grandes procesamientos de información, con tan bajas capacidades, si se distribuyen correctamente los procesos. En primera instancia, se introducen conceptos básicos acerca de las WSN (Wireless Sensor Networks) así como de los elementos principales en dichas redes. Tras conocer el modelo de arquitectura de comunicaciones se procede a presentar la Gestión del Conocimiento de forma teórica y a continuación la interpretación que se ha hecho a partir de diversas referencias bibliográficas para llevar a cabo la implementación del proyecto. El siguiente paso es describir punto por punto todos los componentes del Simulador; librerías, funcionamiento y demás cuestiones sobre configuración y puesta a punto. Como escenario de aplicación se plantea una red de sensores inalámbricos básica cuya topología y ubicación es completamente configurable. Se lleva a cabo una configuración a nivel de red basada en el protocolo 6LowPAN pero con posibilidad de simplificarlo. Los datos se procesan de acuerdo a un modelo piramidal de Gestión de Conocimiento adaptable a las necesidades del usuario. Mediante la utilización de las diversas opciones que proporciona la interfaz gráfica implementada y los documentos de resultados que se van generando, se puede llevar a cabo un detallado estudio posterior de la simulación y comprobar si se cumplen las expectativas planteadas. Knowledge management (KM) is based on the collection, filtering, processing and analysis of some raw data which such refinement it can be turned into knowledge or wisdom. These practices will take place in a WSN (Wireless Sensor Network) consists of sophisticated devices commonly known as "dots" and whose main characteristics are its low capacity for memory, battery or autonomy. A primary objective of this Project will be to join a WSN with Knowledge Management and show that it is possible make largo information processing, with such low capacity if the processes are properly distributed. First, we introduce basic concepts about the WSN (Wireless Sensor Networks) and major elements of these networks. After meeting the communications architecture model, we proceed to show the Knowledge Management theory and then the interpretation of several bibliographic references to carry out the project implementation. The next step is discovering point by point all over the Simulator components; libraries, operation and the rest of points about configuration and tuning. As application scenario we propose a basic wireless sensor network whose topology and location is completely customizable. It will perform a network level configuration based in W6LowPAN Protocol. Data is processed according to a pyramidal pattern Knowledge Management adaptable to the user´s needs. The hardware elements will suffer more or less energy dependence depending on their role and activity in the network. Through the various options that provide the graphical interface has been implemented and results documents that are generated, can be carried out after a detailed study of the simulation and verify compliance with the expectations raised.

Sistema de Aparcamiento Inteligente Aplicado a las Smart Cities

En las últimas décadas el mundo ha sufrido un aumento exponencial en la utilización de soluciones tecnológicas, lo que ha desembocado en la necesidad de medir situaciones o estados de los distintos objetos que nos rodean. A menudo, no es posible cablear determinados sensores por lo que ese aumento en la utilización de soluciones tecnológicas, se ha visto traducido en un aumento de la necesidad de utilización de sensórica sin cables para poder hacer telemetrías correctas. A nivel social, el aumento de la demografía mundial está estrechamente ligado al aumento de la necesidad de servicios tecnológicos, por lo que es lógico pensar que a más habitantes, más tecnología será consumida. El objetivo de este Proyecto Final de Carrera está basado en la utilización de diversos nodos o también llamados motas capaces de realizar transferencia de datos en modo sin cables, permitiendo así realizar una aplicación real que solvente problemas generados por el aumento de la densidad de población. En concreto se busca la realización de un sistema de aparcamiento inteligente para estacionamientos en superficie, ayudando por tanto a las tareas de ordenación vehicular dentro del marco de las Smart cities. El sistema está basado en el protocolo de comunicaciones 802.15.4 (ZigBee) cuyas características fundamentales radican en el bajo consumo de energía de los componentes hardware asociados. En primer lugar se realizará un Estado del Arte de las Redes Inalámbricas de Sensores, abordando tanto la arquitectura como el estándar Zigbee y finalmente los componentes XBee que se van a utilizar en este Proyecto. Seguidamente se realizará la algoritmia necesaria para el buen funcionamiento del sistema inteligente de estacionamiento y finalmente se realizará un piloto demostrador del correcto funcionamiento de la tecnología. ABSTRACT In the last decades the world has experienced an exponential increase in the use of technological solutions, which has resulted in the need to measure situations or states of the objects around us. Often, wired sensors cannot be used at many situations, so the increase in the use of technological solutions, has been translated into a increase of the need of using wireless sensors to make correct telemetries. At the social level, the increase in global demographics is closely linked to the increased need for technological services, so it is logical that more people, more technology will be consumed. The objective of this Final Project is based on the use of various nodes or so-called motes, capable of performing data transfer in wireless mode, thereby allowing performing a real application solving problems generated by the increase of population densities. Specifically looking for the realization of a smart outdoor parking system, thus helping to vehicular management tasks within the framework of the Smart Cities. The system is based on the communication protocol 802.15.4 (ZigBee) whose main characteristics lie in the low energy consumption associated to the hardware components. First there will be a State of the Art of Wireless Sensor Networks, addressing both architecture and finally the Zigbee standard XBee components to be used in this project. Then the necessary algorithms will be developed for the proper working of the intelligent parking system and finally there will be a pilot demonstrator validating the whole system.

Estudio de redes WSN y su aplicación a la ingeniería civil

Las redes inalámbricas están experimentando un gran crecimiento en el campo de la instrumentación electrónica. En concreto las redes de sensores inalámbricas (WSN de Wireless Sensor Network) suponen la opción más ventajosa para su empleo en la instrumentación electrónica ya que sus principales características se acoplan perfectamente a las necesidades. Las WSN permiten la utilización de un número relativamente alto de nodos, están orientadas a sistemas de bajo consumo y funcionamiento con baterías y poseen un ancho de banda adecuado para las necesidades de la instrumentación electrónica. En este proyecto fin de carrera se ha realizado un estudio de las tecnologías inalámbricas disponibles, se han comparado y se ha elegido la tecnología ZigBeeTM por considerarse la más adecuada y la que más se ajusta a las necesidades descritas. En el desarrollo de mi vida profesional se han conectado dos campos teóricamente distantes como son la instrumentación electrónica y la ingeniería civil. En este proyecto se hace una descripción de la instrumentación que se utiliza para controlar estructuras como presas, túneles y puentes y se proponen casos prácticos en los que las redes WSN aportan valor añadido a instrumentación actual y a los sistemas de comunicaciones utilizados. Se definen tanto los sistemas de comunicaciones utilizados actualmente como una serie de sensores utilizados para medir los principales parámetros a controlar en una obra civil. Por último se ha desarrollado una aplicación de prueba de una red ZigBeeTM basada en equipos comerciales del fabricante Digi. consiste en una aplicación desarrollada en entorno web que maneja de forma remota, a través de Internet, las entradas y salidas digitales y analógicas de los nodos que forman la red. Se forma una red ZigBeeTM con un coordinador, un router y un dispositivo final. El Coordinador está integrado en un Gateway que permite acceder a la red ZigBeeTM a través de internet y conocer el estado de los nodos que forman la red. Con los comandos adecuados se puede leer el estado de las entradas y salidas analógicas y digitales y cambiar el estado de una salida digital. ABSTRACT. Wireless networks are experiencing tremendous growth in the field of electronic instrumentation. In particular wireless sensor networks represent the most advantageous for use in electronic instrumentation since its main characteristics fit perfectly to the needs. The WSN allow the use of a relatively large number of nodes, are aimed at low-power systems and battery operation and have an adequate bandwidth for the needs of electronic instrumentation. In this project has made a study of available wireless technologies have been compared and chosen ZigBeeTM technology was considered the most appropriate to the needs described. In the course of my professional life have connected two fields are theoretically distant as electronic instrumentation and civil engineering. In this project, there is a description of the instrumentation used to control structures such as dams, tunnels and bridges and proposes practical cases in which WSN networks add value to current instrumentation and communications systems used. There are defined as communications systems now being used as a set of sensors used to measure the main parameters to be controlled in a civil structure. Finally, I have developed a test application based ZigBeeTM networking equipment maker Digi trading. It consists of a Web-based application developed to manage remotely, via the Internet, the digital and analog inputs and outputs nodes forming the network. ZigBeeTM It forms a network with a coordinator, router and end device. The Coordinator is built into a gateway that allows access to the ZigBeeTM network through internet and know the status of the nodes forming the network. With the appropriate command can read the status of the digital inputs and outputs and change the state of a digital output.

Propuesta de aplicación de una red de sensores en emergencias

El auge y evolución de los sistemas de comunicaciones móviles y de las redes inalámbricas avanzadas, sucedido desde principios del siglo XXI, han propiciado el uso de Redes de Sensores Inalámbricos (RSI) en múltiples ámbitos de interés. Dichas redes están típicamente compuestas por dispositivos inalámbricos autónomos que incorporan sensores para la recogida de datos de distinta naturaleza. Las RSI se caracterizan por su escalabilidad, ausencia de cableado, pequeño tamaño, bajo consumo, gran variedad de magnitudes físico/químicas medibles, entre otras, cuyas cualidades las hace muy interesantes para su aplicación en multitud de escenarios de la Sociedad de la Información, tales como domótica, agricultura y ganadería, medioambiente, salud, procesos industriales, logística, seguridad o ciudades inteligentes, ente otras. En este Trabajo Fin de Máster, se propone el uso de las RSI en el escenario de Emergencias donde cobra gran importancia la usabilidad, la fiabilidad, la disponibilidad, y la robustez de los sistemas a emplear en condiciones hostiles, especialmente en las de bomberos. Es por ello que se analizarán previamente los trabajos de RSI desarrollados para estos entornos y que sugieren qué aplicaciones garantizan el cumplimiento de los requerimientos mencionados. Se aborda la utilización de una primera RSI para la monitorización ambiental de tres Centros de Procesado de Datos (CPD) del departamento de TI de Emergencias, siendo este un entorno sin movilidad, más controlado y que aporta la adquisición de experiencia en la utilización de las RSI de cara a un entorno móvil más complejo. A continuación, para el entorno móvil se ha desarrollado y validado un prototipo experimental de RSI para el seguimiento de salida de parques de bomberos de vehículos con su dotación. Así mismo se implementa un prototipo para la ayuda a la localización de bomberos y/o personas en un siniestro. Estas RSI se desarrollan e implantan en el entorno de Emergencias del Ayuntamiento de Madrid, entidad sin cuyo apoyo habría sido imposible la aplicación práctica de este trabajo. SUMMARY. The rise and evolution of mobile communication systems and advanced wireless networks in early XXI century have allowed to taking advantage of Wireless Sensor Networks (WSN). These networks are composed of independent wireless devices that incorporate sensors for collecting data of different nature. The WSN is characterized by its scalability, no wiring, small size, low power consumption, wide range of physical magnitudes measurable, among others. These qualities make them very interesting for application in many scenarios to the Information Society, such as, domotic, agriculture, smart environment, ehealth, industrial control, logistics, security and smart cities, among others. This work proposes to use WSN in the emergency scenario where is very important the usability, reliability, availability, and robustness of the systems to be used in hostile conditions, especially in fire-fighters environment. That is why WSN works in emergency will be studied to tackle what applications compliance with the above requirements. The first WSN developed will be environmental monitoring of three CPDs IT department Emergency. This scenario is a non-mobile environment, more controlled and bring gaining experience in the use of WSN to face mobile environment which is more complex. Then, for the mobile environment is developed an experimental prototype of WSN for tracking fire vehicles living fire stations with their equipment. Another prototype is foreseen to be implemented to assist fire-fighters location and / or people in a disaster. These WSN are developed and implemented for Madrid City Emergency, whose involvement was critical to put this research into stage.