Sensor fault-tolerant observer applied in satellite attitude control

The observing failure and feedback instability might happen when the partial sensors of a satellite attitude control system (SACS) go wrong. A fault diagnosis and isolation (FDI) method based on a fault observer is introduced to detect and isolate the fault sensor at first. Based on the FDI result, the object system state-space equation is transformed and divided into a corresponsive triangular canonical form to decouple the normal subsystem from the fault subsystem. And then the KX fault-tolerant observers of the system in different modes are designed and embedded into online monitoring. The outputs of all KX fault-tolerant observers are selected by the control switch process. That can make sense that the SACS is part-observed and in stable when the partial sensors break down. Simulation results demonstrate the effectiveness and superiority of the proposed method.

Change Point Estimation in Monitoring Survival Time

Precise identification of the time when a change in a hospital outcome has occurred enables clinical experts to search for a potential special cause more effectively. In this paper, we develop change point estimation methods for survival time of a clinical procedure in the presence of patient mix in a Bayesian framework. We apply Bayesian hierarchical models to formulate the change point where there exists a step change in the mean survival time of patients who underwent cardiac surgery. The data are right censored since the monitoring is conducted over a limited follow-up period. We capture the effect of risk factors prior to the surgery using a Weibull accelerated failure time regression model. Markov Chain Monte Carlo is used to obtain posterior distributions of the change point parameters including location and magnitude of changes and also corresponding probabilistic intervals and inferences. The performance of the Bayesian estimator is investigated through simulations and the result shows that precise estimates can be obtained when they are used in conjunction with the risk-adjusted survival time CUSUM control charts for different magnitude scenarios. The proposed estimator shows a better performance where a longer follow-up period, censoring time, is applied. In comparison with the alternative built-in CUSUM estimator, more accurate and precise estimates are obtained by the Bayesian estimator. These superiorities are enhanced when probability quantification, flexibility and generalizability of the Bayesian change point detection model are also considered.

Reducing Actuator Switchings for Motion Control of Autonomous Underwater Vehicles

A priority when designing control strategies for autonomous underwater vehicles is to emphasize their cost of implementation on a real vehicle. Indeed, due to the vehicles' design and the actuation modes usually under consideration for underwater plateforms the number of actuator switchings must be kept to a small value to insure feasibility and precision. This is the main objective of the algorithm presented in this paper. The theory is illustrated on two examples, one is a fully actuated underwater vehicle capable of motion in six-degrees-of freedom and one is minimally actuated with control motions in the vertical plane only.

Morphological design control for large-scale city development : a new proposal

Whereas many good examples can be found of the study of urban morphology informing the design of new residential areas in Europe, it is much more difficult to find examples relating to other land uses and outside of Europe. This paper addresses a particular issue, the control and coordination of large and complex development schemes within cities, and, in doing so, considers commercial and mixed-use schemes outside of Europe. It is argued that urban morphology has much to offer for both the design of such development and its implementation over time. Firstly, lessons are drawn from the work of Krier and Rossi in Berlin, the form-based guidance developed in Chelmsford, UK, and the redesign and coordination of the Melrose Arch project in Johannesburg, SA. A recent development at Boggo Road in Brisbane, Australia, is then subjected to a more detailed examination. It is argued that the scheme has been unsatisfactory in terms of both design and implementation. An alternative framework based on historical morphological studies is proposed that would overcome these deficiencies. It is proposed that this points the way to a general approach that could be incorporated within the planning process internationally.

A tutorial on visual servo control

This article provides a tutorial introduction to visual servo control of robotic manipulators. Since the topic spans many disciplines our goal is limited to providing a basic conceptual framework. We begin by reviewing the prerequisite topics from robotics and computer vision, including a brief review of coordinate transformations, velocity representation, and a description of the geometric aspects of the image formation process. We then present a taxonomy of visual servo control systems. The two major classes of systems, position-based and image-based systems, are then discussed in detail. Since any visual servo system must be capable of tracking image features in a sequence of images, we also include an overview of feature-based and correlation-based methods for tracking. We conclude the tutorial with a number of observations on the current directions of the research field of visual servo control.

Modelling port water collision risk using traffic conflicts

Navigational collisions are one of the major safety concerns for many seaports. Despite the extent of work recently done on collision risk analysis in port waters, little is known about the influencing factors of the risk. This paper develops a technique for modeling collision risks in port waterways in order to examine the associations between the risks and the geometric, traffic, and regulatory control characteristics of waterways. A binomial logistic model, which accounts for the correlations in the risks of a particular fairway at different time periods, is derived from traffic conflicts and calibrated for the Singapore port fairways. Estimation results show that the fairways attached to shoreline, traffic intersection and international fairway attribute higher risks, whereas those attached to confined water and local fairway possess lower risks. Higher risks are also found in the fairways featuring higher degree of bend, lower depth of water, higher numbers of cardinal and isolated danger marks, higher density of moving ships and lower operating speed. The risks are also found to be higher for night-time conditions.

Hierarchical modeling of perceived collision risks in port fairways

Navigational collisions are one of the major safety concerns in many seaports. Despite the extent of recent works done on port navigational safety research, little is known about harbor pilot’s perception of collision risks in port fairways. This paper uses a hierarchical ordered probit model to investigate associations between perceived risks and the geometric and traffic characteristics of fairways and the pilot attributes. Perceived risk data, collected through a risk perception survey conducted among the Singapore port pilots, are used to calibrate the model. Intra-class correlation coefficient justifies use of the hierarchical model in comparison with an ordinary model. Results show higher perceived risks in fairways attached to anchorages, and in those featuring sharper bends and higher traffic operating speeds. Lesser risks are perceived in fairways attached to shoreline and confined waters, and in those with one-way traffic, traffic separation scheme, cardinal marks and isolated danger marks. Risk is also found to be perceived higher in night.

Rapid prototyping framework for visual control of autonomous micro aerial vehicles

Rapid prototyping environments can speed up the research of visual control algorithms. We have designed and implemented a software framework for fast prototyping of visual control algorithms for Micro Aerial Vehicles (MAV). We have applied a combination of a proxy-based network communication architecture and a custom Application Programming Interface. This allows multiple experimental configurations, like drone swarms or distributed processing of a drone's video stream. Currently, the framework supports a low-cost MAV: the Parrot AR.Drone. Real tests have been performed on this platform and the results show comparatively low figures of the extra communication delay introduced by the framework, while adding new functionalities and flexibility to the selected drone. This implementation is open-source and can be downloaded from www.vision4uav.com/?q=VC4MAV-FW

See-and-avoid quadcopter using fuzzy control optimized by cross-entropy

In this work we present an optimized fuzzy visual servoing system for obstacle avoidance using an unmanned aerial vehicle. The cross-entropy theory is used to optimise the gains of our controllers. The optimization process was made using the ROS-Gazebo 3D simulation with purposeful extensions developed for our experiments. Visual servoing is achieved through an image processing front-end that uses the Camshift algorithm to detect and track objects in the scene. Experimental flight trials using a small quadrotor were performed to validate the parameters estimated from simulation. The integration of cross- entropy methods is a straightforward way to estimate optimal gains achieving excellent results when tested in real flights.

UAS See-and-Avoid using two different approaches of Fuzzy Control

This work presents two UAS See and Avoid approaches using Fuzzy Control. We compare the performance of each controller when a Cross-Entropy method is applied to optimase the parameters for one of the controllers. Each controller receive information from an image processing front-end that detect and track targets in the environment. Visual information is then used under a visual servoing approach to perform autonomous avoidance. Experimental flight trials using a small quadrotor were performed to validate and compare the behaviour of both controllers

Evaluation of the control of carbon emissions of construction facilities in Hong Kong

This paper investigates the policies and instruments adopted in Hong Kong to control the carbon emissions of construction facilities, including the whole building life cycle: production of material stage, construction stage, operation stage and demolition stage. This commences with a literature review comparing activities world-wide to those in Hong Kong to identify the main issues at stake, followed by a report on a series of local interviews to evaluate the present situation in Hong Kong, as well as future opportunities for local carbon mitigation. The interviewees included practitioners from engineering contracting firms, consulting firms, clients and energy provider, together with two university experts and a counsellor. A small case study is also provided of a building project in Hong Kong to illustrate some of the innovative design aspects being incorporated into buildings in Hong Kong as a result of the current emphasis on sustainability. The paper concludes with a summary of main findings and proposals for improvement in policy related to carbon mitigation and building sustainability in Hong Kong.

Socioeconomic inequalities in weight status among mid-aged adults : the contribution of perceptions of weight status and weight-control behaviours

Background Socioeconomically-disadvantaged adults in developed countries experience a higher prevalence of a number of chronic diseases, such as cardiovascular disease, type 2 diabetes, osteoarthritis and some forms of cancer. Overweight and obesity are major risk factors for these diseases. Lower socioeconomic groups have a greater prevalence of overweight and obesity and this may contribute to their higher morbidity and mortality. International studies suggest that socioeconomic groups may differ in their self-perceptions of weight status and their engagement in weightcontrol behaviours (WCBs). Research has shown that lower socioeconomic adults are more likely to underestimate their weight status, and are less likely to engage in WCBs. This may contribute (in part) to the marked inequalities in weight status observed at the population level. There are few, and somewhat limited, Australian studies that have examined the types of weight-control strategies people adopt, the barriers to their weight control, the determinants of their perceived weight status and WCBs. Furthermore, there are no known Australian studies that have examined socioeconomic differences in these factors to better understand the reasons for socioeconomic inequalities in weight status. Hence, the overall aim of this Thesis is to examine why socioeconomically-disadvantaged group experience a greater prevalence of overweight and obesity than their more-advantaged counterparts. Methods This Thesis used data from two sources. Men and women aged 45 to 60 years were examined from both data source. First, the longitudinal Australian Diabetes, Obesity and Lifestyle (AusDiab) Study were used to advance our knowledge and understanding of socioeconomic differences in weight change, perceived weight status and WCBs. A total of 2753 participants with measured weights at both baseline (1999-2000) and follow-up (2004-2005) were included in the analyses. Percent weight change over the five-year interval was calculated and perceived weight status, WCBs and highest attained education were collected at baseline. Second, the Candidate conducted a postal questionnaire from 1013 Brisbane residents (69.8 % response rate) to investigate the relationship between socioeconomic position, determinants of perceived weight status, WCBs, and barriers and reasons to weight control. A test-retest reliability study was conducted to determine the reliability of the new measures used in the questionnaire. Most new measures had substantial to almost perfect reliability when considering either kappa coefficient or crude agreement. Results The findings from the AusDiab Study (accepted for publication in the Australian and New Zealand Journal of Public Health) showed that low-educated men and women were more likely to be obese at baseline compared to their higheducated respondents (O.R. = 1.97, 95 % C.I. = 1.30-2.98 and O.R. = 1.52, 95 % C.I. = 1.03-2.25, respectively). Over the five year follow-up period (1999-2000 to 2004- 05) there were no socioeconomic differences in weight change among men, however socioeconomically-disadvantaged women had greater weight gains. Participants perceiving themselves as overweight gained less weight than those who saw themselves as underweight or normal weight. There was no relationship between engaging in WCBs and five-year weight change. The postal questionnaire data showed that socioeconomically-disadvantaged groups were less likely to engage in WCBs. If they did engage in weight control, they were less likely to adopt exercise strategies, including moderate and vigorous physical activities but were more likely to decrease their sitting time to control their weight. Socioeconomically-disadvantaged adults reported more barriers to weight control; such as perceiving weight loss as expensive, requiring a lot of cooking skills, not being a high priority and eating differently from other people in the household. These results have been accepted for publication in Public Health Nutrition. The third manuscript (under review in Social Science and Medicine) examined socioeconomic differences in determinants of perceived weight status and reasons for weight control. The results showed that lower socioeconomic adults were more likely to specify the following reasons for weight control: they considered themselves to be too heavy, for occupational requirements, on recommendation from their doctor, family members or friends. Conversely, high-income adults were more likely to report weight control to improve their physical condition or to look more attractive compared with those on lower-incomes. There were few socioeconomic differences in the determinants of perceived weight status. Conclusions Education inequalities in overweight/obesity among men and women may be due to mis-perceptions of weight status; overweight or obese individuals in loweducated groups may not perceive their weight as problematic and therefore may not pay attention to their energy-balance behaviours. Socioeconomic groups differ in WCBs, and their reasons and perceived barriers to weight control. Health promotion programs should encourage weight control among lower socioeconomic groups. More specifically, they should encourage the engagement of physical activity or exercise and dietary strategies among disadvantaged groups. Furthermore, such programs should address potential barriers for weight control that disadvantaged groups may encounter. For example, disadvantaged groups perceive that weight control is expensive, requires cooking skills, not a high priority and eating differently from other people in the household. Lastly, health promotion programs and policies aimed at reducing overweight and obesity should be tailored to the different reasons and motivations to weight control experienced by different socioeconomic groups. Weight-control interventions targeted at higher socioeconomic groups should use improving physical condition and attractiveness as motivational goals; while, utilising social support may be more effective for encouraging weight control among lower socioeconomic groups.

A hierarchical evolutionary algorithmic design (HEAD) system for generating and evolving building design models

This thesis develops a detailed conceptual design method and a system software architecture defined with a parametric and generative evolutionary design system to support an integrated interdisciplinary building design approach. The research recognises the need to shift design efforts toward the earliest phases of the design process to support crucial design decisions that have a substantial cost implication on the overall project budget. The overall motivation of the research is to improve the quality of designs produced at the author's employer, the General Directorate of Major Works (GDMW) of the Saudi Arabian Armed Forces. GDMW produces many buildings that have standard requirements, across a wide range of environmental and social circumstances. A rapid means of customising designs for local circumstances would have significant benefits. The research considers the use of evolutionary genetic algorithms in the design process and the ability to generate and assess a wider range of potential design solutions than a human could manage. This wider ranging assessment, during the early stages of the design process, means that the generated solutions will be more appropriate for the defined design problem. The research work proposes a design method and system that promotes a collaborative relationship between human creativity and the computer capability. The tectonic design approach is adopted as a process oriented design that values the process of design as much as the product. The aim is to connect the evolutionary systems to performance assessment applications, which are used as prioritised fitness functions. This will produce design solutions that respond to their environmental and function requirements. This integrated, interdisciplinary approach to design will produce solutions through a design process that considers and balances the requirements of all aspects of the design. Since this thesis covers a wide area of research material, 'methodological pluralism' approach was used, incorporating both prescriptive and descriptive research methods. Multiple models of research were combined and the overall research was undertaken following three main stages, conceptualisation, developmental and evaluation. The first two stages lay the foundations for the specification of the proposed system where key aspects of the system that have not previously been proven in the literature, were implemented to test the feasibility of the system. As a result of combining the existing knowledge in the area with the newlyverified key aspects of the proposed system, this research can form the base for a future software development project. The evaluation stage, which includes building the prototype system to test and evaluate the system performance based on the criteria defined in the earlier stage, is not within the scope this thesis. The research results in a conceptual design method and a proposed system software architecture. The proposed system is called the 'Hierarchical Evolutionary Algorithmic Design (HEAD) System'. The HEAD system has shown to be feasible through the initial illustrative paper-based simulation. The HEAD system consists of the two main components - 'Design Schema' and the 'Synthesis Algorithms'. The HEAD system reflects the major research contribution in the way it is conceptualised, while secondary contributions are achieved within the system components. The design schema provides constraints on the generation of designs, thus enabling the designer to create a wide range of potential designs that can then be analysed for desirable characteristics. The design schema supports the digital representation of the human creativity of designers into a dynamic design framework that can be encoded and then executed through the use of evolutionary genetic algorithms. The design schema incorporates 2D and 3D geometry and graph theory for space layout planning and building formation using the Lowest Common Design Denominator (LCDD) of a parameterised 2D module and a 3D structural module. This provides a bridge between the standard adjacency requirements and the evolutionary system. The use of graphs as an input to the evolutionary algorithm supports the introduction of constraints in a way that is not supported by standard evolutionary techniques. The process of design synthesis is guided as a higher level description of the building that supports geometrical constraints. The Synthesis Algorithms component analyses designs at four levels, 'Room', 'Layout', 'Building' and 'Optimisation'. At each level multiple fitness functions are embedded into the genetic algorithm to target the specific requirements of the relevant decomposed part of the design problem. Decomposing the design problem to allow for the design requirements of each level to be dealt with separately and then reassembling them in a bottom up approach reduces the generation of non-viable solutions through constraining the options available at the next higher level. The iterative approach, in exploring the range of design solutions through modification of the design schema as the understanding of the design problem improves, assists in identifying conflicts in the design requirements. Additionally, the hierarchical set-up allows the embedding of multiple fitness functions into the genetic algorithm, each relevant to a specific level. This supports an integrated multi-level, multi-disciplinary approach. The HEAD system promotes a collaborative relationship between human creativity and the computer capability. The design schema component, as the input to the procedural algorithms, enables the encoding of certain aspects of the designer's subjective creativity. By focusing on finding solutions for the relevant sub-problems at the appropriate levels of detail, the hierarchical nature of the system assist in the design decision-making process.

Control and application of minimally-actuated underwater vehicles

Establishing a persistent presence in the ocean with an Autonomous Underwater Vehicle capable of observing temporal variability of large-scale ocean processes requires a unique sensor platform. In this paper, we examine the utility of Lagrangian profiling floats for such extended deployments. We propose a strategy that utilizes ocean model predictions to facilitate a basic level of autonomy to achieve general control of this minimally-actuated underwater vehicle. We extend experimentally validated techniques for utilising ocean current models to control under-actuated autonomous underwater vehicles by presenting this investigation into the application of these methods on profiling floats. With the appropriate vertical actuation, and utilising spatiotemporal variations in water speed and direction, we show that broad controllability results can be met. First, we apply an A* planner to a local controllability map generated from predictions of ocean currents. This computes a path between start and goal waypoints that has the highest likelihood of successful execution over a given duration. The computed depth plan is generated with a model predictive controller, and selects the depths for the vehicle so that ambient currents guide it toward the goal. Mission constraints are included to simulate and motivate a practical data collection mission. Results are presented in simulation for a mission off the coast of Los Angeles, CA USA, that show surprising results in the ability of a drifting vehicle to maintain a prescribed course and reach a desired location.

Bayesian hierarchical analysis on crash prediction models

Traditional crash prediction models, such as generalized linear regression models, are incapable of taking into account the multilevel data structure, which extensively exists in crash data. Disregarding the possible within-group correlations can lead to the production of models giving unreliable and biased estimates of unknowns. This study innovatively proposes a -level hierarchy, viz. (Geographic region level – Traffic site level – Traffic crash level – Driver-vehicle unit level – Vehicle-occupant level) Time level, to establish a general form of multilevel data structure in traffic safety analysis. To properly model the potential cross-group heterogeneity due to the multilevel data structure, a framework of Bayesian hierarchical models that explicitly specify multilevel structure and correctly yield parameter estimates is introduced and recommended. The proposed method is illustrated in an individual-severity analysis of intersection crashes using the Singapore crash records. This study proved the importance of accounting for the within-group correlations and demonstrated the flexibilities and effectiveness of the Bayesian hierarchical method in modeling multilevel structure of traffic crash data.