Role of carbon nanotube dispersion in fracture toughening of plasma sprayed aluminum oxide - carbon nanotube nanocomposite coating

Aluminum oxide (A1203, or alumina) is a conventional ceramic known for applications such as wear resistant coatings, thermal liners, heaters, crucibles, dielectric systems, etc. However applications of A1203 are limited owing to its inherent brittleness. Due to its excellent mechanical properties and bending strength, carbon nanotubes (CNT) is an ideal reinforcement for A1203 matrix to improve its fracture toughness. The role of CNT dispersion in the fracture toughening of the plasma sprayed A1203-CNT nanocomposite coating is discussed in the current work. Pretreatment of powder feedstock is required for dispersing CNTs in the matrix. Four coatings namely spray dried A1203 (A-SD), A1203 blended with 4wt.% CNT (A4C-B), composite spray dried A1203-4wt.% CNT (A4C-SD) and composite spray dried A1203-8wt.% CNT (A8CSD), are synthesized by plasma spraying. Owing to extreme temperatures and velocities involved in the plasma spraying of ceramics, retention of CNTs in the resulting coatings necessitates optimizing plasma processing parameters using an inflight particle diagnostic sensor. A bimodal microstructure was obtained in the matrix that consists of fully melted and resolidified structure and solid state sintered structure. CNTs are retained both in the fully melted region and solid-state sintered regions of processed coatings. Fracture toughness of A-SD, A4C-B, A4C-SD and A8C-SD coatings was 3.22, 3.86, 4.60 and 5.04 MPa m1/2 respectively. This affirms the improvement of fracture toughness from 20 % (in A4C-B coating) to 43% (in A4C-SD coating) when compared to the A-SD coating because of the CNT dispersion. Fracture toughness improvement from 43 % (in A4C-SD) to 57% (in A8C-SD) coating is evinced because of the CNT content. Reinforcement by CNTs is described by its bridging, anchoring, hook formation, impact alignment, fusion with splat, and mesh formation. The A1203/CNT interface is critical in assisting the stress transfer and utilizing excellent mechanical properties of CNTs. Mathematical and computational modeling using ab-initio principle is applied to understand the wetting behavior at the A1203/CNTinterface. Contrasting storage modulus was obtained by nanoindentation (~ 210, 250, 250-350 and 325-420 GPa in A-SD, A4C-B, A4C-SD, and A8C-SD coatings respectively) depicting the toughening associated with CNT content and dispersion.

Le Facce del Coating

Studio degli elementi frontali, posteriori e di collegamento di una macchina per il coating continuo di prodotti farmaceutici.

Observation of manganese coating and encrustation in different environments of the North-Western Atlantic ocean

The major topographic features, or provinces, beyond the continental slope off the Atlantic coast of the United States are (1) Sohm Plain, (2) Hatteras Plain, (3) Nares Plain, (4) Blake Basin, (5) Blake Plateau-Bahama Banks, and (6) Bermuda Rise. The whole of the described area is commonly referred to as the North American Basin. This basin is bounded on the north by Newfoundland Ridge and on the south by Puerto Rico Trench. Topographic features of note within the basin are the divide and the area of depressions between Sohm and Hatteras Plains, the sharply crested Blake Ridge, and the Puerto Rico Ridge. Recently accumulated data on deep-sea oores has given good evidence that the silt and sand covering the abyssal plains are displaced continental sediments in a virtually quartz-free oceanic environment. These sediments were deposited on a primary volcanic bottom. The primary or volcanic bottom is characterized by abyssal hills and seamounts, and the sediment bottom is characterized by abyssal plains, which extend seaward from the continental margins. On the Blake Plateau, bottom photographs and dredge hauls in the axis of the stream show that locally sediment has been removed and the bottom is paved with crusts and nodules of manganese. Photographs and dredged samples from the outer part of the New England Seamount, Chain and Caryn Peak also indicate extensive encrustations of manganese oxide which acts as a binding agent in areas of ooze or other organic debris and thus helps to stabilize the bottom.

Design of experiments to study the impact of process parameters on droplet size and development of non-invasive imaging techniques in tablet coating

Atomisation of an aqueous solution for tablet film coating is a complex process with multiple factors determining droplet formation and properties. The importance of droplet size for an efficient process and a high quality final product has been noted in the literature, with smaller droplets reported to produce smoother, more homogenous coatings whilst simultaneously avoiding the risk of damage through over-wetting of the tablet core. In this work the effect of droplet size on tablet film coat characteristics was investigated using X-ray microcomputed tomography (XμCT) and confocal laser scanning microscopy (CLSM). A quality by design approach utilising design of experiments (DOE) was used to optimise the conditions necessary for production of droplets at a small (20 μm) and large (70 μm) droplet size. Droplet size distribution was measured using real-time laser diffraction and the volume median diameter taken as a response. DOE yielded information on the relationship three critical process parameters: pump rate, atomisation pressure and coating-polymer concentration, had upon droplet size. The model generated was robust, scoring highly for model fit (R2 = 0.977), predictability (Q2 = 0.837), validity and reproducibility. Modelling confirmed that all parameters had either a linear or quadratic effect on droplet size and revealed an interaction between pump rate and atomisation pressure. Fluidised bed coating of tablet cores was performed with either small or large droplets followed by CLSM and XμCT imaging. Addition of commonly used contrast materials to the coating solution improved visualisation of the coating by XμCT, showing the coat as a discrete section of the overall tablet. Imaging provided qualitative and quantitative evidence revealing that smaller droplets formed thinner, more uniform and less porous film coats.

Microparticle surface layering through dry coating:impact of moisture content and process parameters on the properties of orally disintegrating tablets

OBJECTIVES: The aim of this study was to investigate the influence of process parameters during dry coating on particle and dosage form properties upon varying the surface adsorbed moisture of microcrystalline cellulose (MCC), a model filler/binder for orally disintegrating tablets (ODTs). METHODS: The moisture content of MCC was optimised using the spray water method and analysed using thermogravimetric analysis. Microproperty/macroproperty assessment was investigated using atomic force microscopy, nano-indentation, scanning electron microscopy, tablet hardness and disintegration testing. KEY FINDINGS: The results showed that MCC demonstrated its best flowability at a moisture content of 11.2% w/w when compared to control, comprising of 3.9% w/w moisture. The use of the composite powder coating process (without air) resulted in up to 80% increase in tablet hardness, when compared to the control. The study also demonstrated that surface adsorbed moisture can be displaced upon addition of excipients during dry processing circumventing the need for particle drying before tabletting. CONCLUSIONS: It was concluded that MCC with a moisture content of 11% w/w provides a good balance between powder flowability and favourable ODT characteristics.

Chemical Sensor Based on a Long-Period Fibre Grating Modified by a Functionalized Polydimethylsiloxane Coating

A chemical sensor based on a coated long-period grating has been prepared and characterized. Designer coatings based on polydimethylsiloxane were prepared by the incorporation of diphenylsiloxane and titanium cross-linker in order to provide enhanced sensitivity for a variety of key environmental pollutants and optimal refractive index of the coating. Upon microextraction of the analyte into the polymer matrix, an increase in the refractive index of the coating resulted in a change in the attenuation spectrum of the long-period grating. The grating was interrogated using ring-down detection as a means to amplify the optical loss and to gain stability against misalignment and power fluctuations. Chemical differentiation of cyclohexane and xylene was achieved and a detection limit of 300 ppm of xylene vapour was realized.

Detection of Human Enteric Viruses in Freshwater from European Countries

The transmission of water-borne pathogens typically occurs by a faecal–oral route, through inhalation of aerosols, or by direct or indirect contact with contaminated water. Previous molecular-based studies have identified viral particles of zoonotic and human nature in surface waters. Contaminated water can lead to human health issues, and the development of rapid methods for the detection of pathogenic microorganisms is a valuable tool for the prevention of their spread. The aims of this work were to determine the presence and identity of representative human pathogenic enteric viruses in water samples from six European countries by quantitative polymerase chain reaction (q-PCR) and to develop two quantitative PCR methods for Adenovirus 41 and Mammalian Orthoreoviruses. A 2-year survey showed that Norovirus, Mammalian Orthoreovirus and Adenoviruses were the most frequently identified enteric viruses in the sampled surface waters. Although it was not possible to establish viability and infectivity of the viruses considered, the detectable presence of pathogenic viruses may represent a potential risk for human health. The methodology developed may aid in rapid detection of these pathogens for monitoring

Detection of Human Enteric Viruses in Freshwater from European Countries

The transmission of water-borne pathogens typically occurs by a faecal–oral route, through inhalation of aerosols, or by direct or indirect contact with contaminated water. Previous molecular-based studies have identified viral particles of zoonotic and human nature in surface waters. Contaminated water can lead to human health issues, and the development of rapid methods for the detection of pathogenic microorganisms is a valuable tool for the prevention of their spread. The aims of this work were to determine the presence and identity of representative human pathogenic enteric viruses in water samples from six European countries by quantitative polymerase chain reaction (q-PCR) and to develop two quantitative PCR methods for Adenovirus 41 and Mammalian Orthoreoviruses. A 2-year survey showed that Norovirus, Mammalian Orthoreovirus and Adenoviruses were the most frequently identified enteric viruses in the sampled surface waters. Although it was not possible to establish viability and infectivity of the viruses considered, the detectable presence of pathogenic viruses may represent a potential risk for human health. The methodology developed may aid in rapid detection of these pathogens for monitoring

Analysis of friction factor reduction in turbulent water flow using a superhydrophobic coating

This study provides experimental and theoretical evidence that the coating of the inner surface of copper pipes with superhydrophobic (SH) materials induces a Cassie state flow regime on the flow of water. This results in an increase in the fluid's dimensionless velocity distribution coefficient, a, which gives rise to an increase in the apparent Reynolds number, which may approach the "plug flow state". Experimental evidence from the SH coating of a classic unsteady-state flow system resulted in a significant decrease in the friction factor and associated energy loss. The friction factor decrease can be attributed to an increase in the apparent Reynolds number. The study demonstrates that the Cassie effects imposed by SH coating can be quantitatively shown to decrease the frictional resistance to flow in commercial pipes.

Enteric methane emissions and nitrogen utilisation efficiency for two genotype of hill hoggets offered fresh, ensiled and pelleted ryegrass

Thirty-six 12-month-old hill hoggets were used in a 2 genotype (18 Scottish Blackface vs. 18 Swaledale×Scottish Blackface)×3 diet (fresh vs. ensiled vs. pelleted ryegrass) factorial design experiment to evaluate the effects of hogget genotype and forage type on enteric methane (CH4) emissions and nitrogen (N) utilisation. The hoggets were offered 3 diets ad libitum with no concentrate supplementation in a single period study with 6 hoggets for each of the 6 genotype×diet combinations (n=6). Fresh ryegrass was harvested daily in the morning. Pelleted ryegrass was sourced from a commercial supplier (Aylescott Driers & Feeds, Burrington, UK) and the ryegrass silage was ensiled with Ecosyl (Lactobacillus plantarum, Volac International Limited, Hertfordshire, UK) as an additive. The hoggets were housed in individual pens for at least 14 d before being transferred to individual respiration chambers for a further 4 d with feed intake, faeces and urine outputs and CH4 emissions measured. There was no significant interaction between genotype and forage type on any parameter evaluated. Sheep offered pelleted grass had greater feed intake (e.g. DM, energy and N) but less energy and nutrient apparent digestibility (e.g. DM, N and neutral detergent fibre (NDF)) than those given fresh grass or grass silage (P<0.001). Feeding pelleted grass, rather than fresh grass or grass silage, reduced enteric CH4 emissions as a proportion of DM intake and gross energy (GE) intake (P<0.01). Sheep offered fresh grass had a significantly lower acid detergent fibre (ADF) apparent digestibility, and CH4 energy output (CH4-E) as a proportion of GE intake than those offered grass silage (P<0.001). There was no significant difference, in CH4 emission rate or N utilisation efficiency when compared between Scottish Blackface and Swaledale × Scottish Blackface. Linear and multiple regression techniques were used to develop relationships between CH4 emissions or N excretion and dietary and animal variables using data from sheep offered fresh ryegrass and grass silage. The equation relating CH4-E (MJ/d) to GE intake (GEI, MJ/d), energy apparent digestibility (DE/GE) and metabolisability (ME/GE) resulted in a high r2 (CH4-E=0.074 GEI+9.2 DE/GE−10.2 ME/GE−0.37, r2=0.93). N intake (NI) was the best predictor for manure N excretion (Manure N=0.66 NI+0.96, r2=0.85). The use of these relationships can potentially improve the precision and decrease the uncertainty in predicting CH4 emissions and N excretion for sheep production systems managed under the current feeding conditions.

A simply effective double-coating cathode with MnO2 nanosheets/graphene as functionalized interlayer for high performance lithium-sulfur batteries

Herein, we report a facile and effective adsorption strategy to improve the performance of Lithium-Sulfur (Li-S) batteries. MnO₂ nanosheets grown on the surface of highly conductive graphene resulted in a coupled composite bilayer electrode when coated onto a sulfur cathode. In this way, a high initial specific capacity of 1395 mA h g^-1 at a rate of 0.5C, a coulombic efficiency approaching 100% and steady cyclic efficiency with a fade rate of 0.3% per cycle from 10 to 100 cycles has been achieved. This hybrid electrode not only shows enhanced electrochemical performance but can also be easily controlled and scaled thereby aiding future commercialization of high-performance Li-S batteries.

Corrosion resistance of self-growing TiC coating on SIMP steel in LBE at 600 °C

SIMP steel was newly developed as a candidate structural material for the accelerator driven subcritical system. The serious decarburization of SIMP steel because of the high Si content was used to successfully form a self-growing TiC coating on the surface, after the Ti deposition as a first step. This TiC layer can effectively protect the surface from the static liquid lead-bismuth eutectic (LBE) corrosion at 600 °C up to 2000 h in the low oxygen LBE. However, in the oxygen saturated LBE, the TiC coating is oxidized into porous TiO2 after only 500 h and fails to protect. Therefore, the self-growing TiC coating is desired only when the oxygen content of LBE is strictly controlled on a low level.

SOL-GEL Lanthanum Phosphate, Composite and coating for functional Applications.

Lanthanum phosphate is one among the lanthanide family of “Rare Earths” following the periodic table of elements. Known under the generic name, Monazite, the rare earth phosphates have melting points above 1900 °C, high thermal phase stability, low thermal conductivity and thermal expansion coefficient similar to some of the high temperature oxides like alumina and zirconia.