An investigation into the properties of non-digestible carbohydrates that selectively promote colonic propionate production

Short chain fatty acids (SCFA), including propionate, are produced by the bacterial fermentation of carbohydrates in the colon. Propionate has many potential roles in health, including inhibiting cholesterol synthesis, de novo lipogenesis and increasing satiety. The profile of SCFA produced is determined by both the substrate available and the bacteria present and may be influenced by environmental conditions within the lumen of the colon. Whilst it may be beneficial to increase colonic propionate production, dietary strategies to achieve this are unproven. Adding propionate to food leads to poorer organoleptic properties, and oral propionate is absorbed in the small intestine. The optimum way to selectively increase colonic propionate would be to select fermentable carbohydrates that selectively promote propionate production. To date, few studies have undertaken a systematic assessment of the factors leading to increased colonic propionate production making the selection of propiogenic carbohydrates challenging. The aim of this thesis was to identify the best carbohydrates for selectively increasing propionate production, and to explore the factors which control propionate production. This work started with a systematic review of the literature for evidence of candidate carbohydrates, which led to a screen of ‘propiogenic’ substrates using in vitro batch fermentations and mechanistic analysis of the impact of pH, bond linkage and orientation using a range of sugars, polysaccharides and fibre sources. A new unit for SCFA production was developed to allow comparison of results from in vitro studies encompassing a range different methodologies found in the literature. The systematic review found that rhamnose yielded the highest rate and proportion of propionate production whereas, for polysaccharides, β-glucan ranked highest for rate and guar gum ranked highest for molar production, but this was not replicated across all studies. Thus, no single NDC was established as highly propiogenic. Some substrates appeared more propiogenic than others and when these were screened in vitro. Laminarin, and other β-glucans ranked highest for propionate production. Legume fibre and mycoprotein fibre were also propiogenic. A full complement of glucose disaccharides were tested to examine the role glycosidic bond orientation and position on propionate production. Of the glucose disaccharides tested, β(1-4) bonding was associated with increased proportion of propionate and α(1-1) and β(1-4) increased the rate and proportion of butyrate production. In conclusion, it appears that for fibre to affect satiety, high intakes of fibre are needed, and which a major mechanism is thought to occur via propionate. Within this thesis it was identified that rather than selecting specific fibres, increasing overall intakes of highly fermentable carbohydrates is as effective at increasing propionate production. Selecting carbohydrates with beta-bonding, particularly laminarin and other β(1-4) fermentable carbohydrates leads to marginal increases in propionate production. Compared with targeted delivery of propionate to the colon, fermentable carbohydrates examined in this thesis have lesser and variable effects on propionate production. A more complete understanding of the impact of bond configurations in polysaccharides, rather than disaccharides, may help selection or design of dietary carbohydrates which selectively promote colonic propionate production substrates for inclusion in functional foods. Overall this study has concluded that few substrates are selectively propiogenic and the evidence suggests that similar changes in propionate production may be achieved by modest changes in dietary fibre intake

The impact of gamma irradiation on the cytotoxic properties and phenolic composition of Thymus vulgaris L. and Menta x piperita L.

Irradiation has been increasingly recognized as an effective decontamination technique, also ensuring the chemical and organoleptic quality of medicinal and aromatic plants 1 . The use of medicinal plants in the prevention and or treatment of several diseases has revealed satisfactory results as anti-inflammatory, antimutagenic, anti-cancer and antioxidant agents 2 . The aim of the present study was to evaluate the effects of gamma irradiation on the cytotoxic properties and phenolic composition of Thymus vulgaris L. and Menta x piperita L. (methanolic extracts). Phenolic compounds were analyzed by HPLC-DAD-ESI MS, while the cytotoxicity of the samples was assessed in MCF-7 (breast adenocarcinoma), NCI-H460 (non-small cell lung cancer), HeLa (cervical carcinoma), HepG2 (hepatocellular carcinoma) cell lines, as also in non-tumor cells (PLP2). Thirteen and fourteen phenolic compounds were detected in T. vulgaris and M. piperita, respectively, but none of them was affected by the irradiation up to a dose of 10 kGy. However, despite there were no changes in the cytotoxic properties of irradiated peppermint samples in tumor cell lines, the thyme samples irradiated with 10 kGy showed higher cytotoxicity in comparison with the samples submitted to other doses (2 and 5 kGy). This highlights that 10 kGy can be a suitable dose to ensure the sanitary treatment, without modifying the bioactive composition and properties of these aromatic plants.

Gamma radiation preserves chemical and bioactive properties of Boletus edulis wild mushrooms

Boletus edulis Bull: Fr. is an edible mushroom quite appreciated for its organoleptic and nutritional properties. However, the seasonality and perishability cause some difficulties in its distribution and marketing in fresh form; losses associated with this type of food during marketing can reach 40% [1]. Irradiation is recognized as a safe and effective method for food preservation, being used worldwide to increase shelf life of fresh and dehydrated products (e.g. fruits, vegetables and spices) [2]. In particular, gamma irradiation has already been applied to cultivated mushrooms (especially Agaricus, Lentinula and Pleurotus Genus) and proved to be an interesting conservation technology [3]. However, the studies with added-value wild species are scarce. In this work, the effects of gamma irradiation on chemical and antioxidant properties of wild B. edulis, were evaluated. Fruiting bodies were obtained in Trás-os-Montes, in the Northeast of Portugal, in November 2012. The irradiation was performed in experimental equipment with 60Co sources at 1 and 2 kGy. All the results were compared with nonirradiated samples (control). Macronutrients and energy value were determined following official procedures of food analysis; fatty acids were analyzed by gas-chromatography coupled to flame ionization detection (GC-FID), while sugars and tocopherols were determined by high performance liquid chromatography (HPLC) coupled to refraction index (RI) and fluorescence detectors, respectively. Antioxidant activity was evaluated in the methanolic extracts by in vitro assays measuring DPPH (1,1-diphenyl-2-picrylhydrazyl) radical scavenging activity, reducing power, inhibition of β- carotene bleaching and inhibition of lipid peroxidation using thiobarbituric acid reactive substances (TBARS) assay. Total phenolics were also determined by the Folin-Ciocalteu assay. The nutritional profiles were not affected in high extension. Fatty acids and sugars were slightly affected, decreasing with the increasing doses. The performed assays for antioxidant activity, indicate that irradiated samples tended to have lower scavenging activity and reducing power, but higher lipid peroxidation inhibition. Despite the detected differences in individual compounds, the results of nutritional parameters, the most relevant in terms of mushroom acceptability by consumers, were less affected, indicating an interesting potential of gamma-irradiation to be used as an effective conservation technology for the studied mushrooms.

Nitrogen vs argon: what is the most effective atmosphere for shelf-life extension of buckler sorrel leaves?

Buckler sorrel (Rumex induratus Boiss. & Reut.) is an underutilized leafy vegetable with peculiar sensory properties and potential as a gourmet food. In the food industry, different packaging methods have been used for shelf-life extension, but it is important to know how the quality of minimally processed vegetable is affected by these treatments. Recently, nitrogen and argon have been used for food packaging. Nitrogen is low soluble in water and other food constituents and does not support the growth of aerobic microbes. In turn, argon is biochemically active and appears to interfere with enzymatic oxygen receptor sites. In this study, modified atmospheres enriched with nitrogen and argon were evaluated for shelf-life extension of buckler sorrel leaves. Wild samples were gathered in Bragança, Portugal, considering local consumers’ sites and criteria. Healthy and undamaged leaves were selected, rinsed in tap water, and a portion was immediately analyzed (non-stored control). The remaining fresh material was packaged in polyethylene bags under nitrogen- and argon-enriched atmospheres and a conventional control atmosphere (air). All packaged samples were stored at 4 ºC for 12 days and then analyzed. The headspace gas composition was monitored during storage. Different quality attributes were evaluated, including visual (colour), nutritional (macronutrients, individual sugars and fatty acids) and bioactive (hydrophilic and lipophilic molecules and antioxidant properties) parameters. Different statistical tools were used; the one-way analysis of variance (ANO VA) was applied for analyse the differences among treatments and a linear discriminant analysis (LDA ) was used to evaluate the effects on the overall postharvest quality. The argon-enriched atmosphere better prevent the samples yellowing. The proximate composition did not change significantly during storage. Samples in control atmosphere revealed higher protein and ash contents and lower levels of lipids. The non-stored control samples presented the higher amounts of fructose, glucose and trehalose. The storage time increased the palmitic acid levels and decreased the content in α-linolenic and linoleic acids. The γ- e δ-tocopherols were higher after the 12 days of cold storage. Probably, the synthesis of these lipophilic compounds was a plant strategy to fight against the abiotic stress induced by storage. Higher levels of total phenolics and flavonoids and increased reducing power and β-carotene bleaching inhibition capacity were also found in the stored control samples. Once again, this result may be attributed to the intrinsic plant-protection mechanisms. Overall, the argon atmosphere was more suitable for quality preservation and shelf-life extension of buckler sorrel.

A new, fast and flexible radiative transfer method for Venus general circulation models

We present a new radiation scheme for the Oxford Planetary Unified Model System for Venus, suitable for the solar and thermal bands. This new and fast radiative parameterization uses a different approach in the two main radiative wavelength bands: solar radiation (0.1-5.5 mu m) and thermal radiation (1.7-260 mu m). The solar radiation calculation is based on the delta-Eddington approximation (two-stream-type) with an adding layer method. For the thermal radiation case, a code based on an absorptivity/emissivity formulation is used. The new radiative transfer formulation implemented is intended to be computationally light, to allow its incorporation in 3D global circulation models, but still allowing for the calculation of the effect of atmospheric conditions on radiative fluxes. This will allow us to investigate the dynamical-radiative-microphysical feedbacks. The model flexibility can be also used to explore the uncertainties in the Venus atmosphere such as the optical properties in the deep atmosphere or cloud amount. The results of radiative cooling and heating rates and the global-mean radiative-convective equilibrium temperature profiles for different atmospheric conditions are presented and discussed. This new scheme works in an atmospheric column and can be easily implemented in 3D Venus global circulation models. (C) 2014 Elsevier Ltd. All rights reserved.

Sonochemical synthesis of CuO nanostructures and their morphology dependent optical and visible light driven photocatalytic properties

A controlled synthesis of CuO nanostructures with various morphologies were successfully achieved by presence/absence of low frequency (42 kHz) ultrasound with two different methods. The size, shape and morphology of the CuO nanostructures were tailored by altering the ultrasound, mode of addition and solvent medium. The crystalline structure and molecular vibrational modes of the prepared nanostructures were analysed through X-ray diffraction and FTIR measurement, respectively which confirmed that the nanostructures were phase pure high-quality CuO with monoclinic crystal structure. The morphological evaluation and elemental composition analysis were done using TEM and EDS attached with SEM, respectively. Furthermore, we demonstrated that the prepared CuO nanostructures could be served as an effective photocatalyst towards the degradation of methyl orange (MO) under visible light irradiation. Among the various nanostructures, the spherical shape CuO nanostructures were found to have the better catalytic activities towards MO dye degradation. The catalytic degradation performance of MO in the presence of CuO nanostructures showed the following order: spherical\nanorod \layered oval \nanoleaf \triangular \shuttles structures. The influence of loading and reusability of catalyst revealed that the efficiency of visible light assisted degradation of MO was effectively enhanced and more than 95 % of degradation was achieved after 3 cycles

CHARACTERIZATION OF THERMAL AND MECHANICAL PROPERTIES OF POLYPROPYLENE–BASED COMPOSITES FOR FUEL CELL BIPOLAR PLATES AND DEVELOPMENT OF EDUCATIONAL TOOLS IN HYDROGEN AND FUEL CELL TECHNOLOGIES

In this project we developed conductive thermoplastic resins by adding varying amounts of three different carbon fillers: carbon black (CB), synthetic graphite (SG) and multi–walled carbon nanotubes (CNT) to a polypropylene matrix for application as fuel cell bipolar plates. This component of fuel cells provides mechanical support to the stack, circulates the gases that participate in the electrochemical reaction within the fuel cell and allows for removal of the excess heat from the system. The materials fabricated in this work were tested to determine their mechanical and thermal properties. These materials were produced by adding varying amounts of single carbon fillers to a polypropylene matrix (2.5 to 15 wt.% Ketjenblack EC-600 JD carbon black, 10 to 80 wt.% Asbury Carbons’ Thermocarb TC-300 synthetic graphite, and 2.5 to 15 wt.% of Hyperion Catalysis International’s FIBRILTM multi-walled carbon nanotubes) In addition, composite materials containing combinations of these three fillers were produced. The thermal conductivity results showed an increase in both through–plane and in–plane thermal conductivities, with the largest increase observed for synthetic graphite. The Department of Energy (DOE) had previously set a thermal conductivity goal of 20 W/m·K, which was surpassed by formulations containing 75 wt.% and 80 wt.% SG, yielding in–plane thermal conductivity values of 24.4 W/m·K and 33.6 W/m·K, respectively. In addition, composites containing 2.5 wt.% CB, 65 wt.% SG, and 6 wt.% CNT in PP had an in–plane thermal conductivity of 37 W/m·K. Flexural and tensile tests were conducted. All composite formulations exceeded the flexural strength target of 25 MPa set by DOE. The tensile and flexural modulus of the composites increased with higher concentration of carbon fillers. Carbon black and synthetic graphite caused a decrease in the tensile and flexural strengths of the composites. However, carbon nanotubes increased the composite tensile and flexural strengths. Mathematical models were applied to estimate through–plane and in–plane thermal conductivities of single and multiple filler formulations, and tensile modulus of single–filler formulations. For thermal conductivity, Nielsen’s model yielded accurate thermal conductivity values when compared to experimental results obtained through the Flash method. For prediction of tensile modulus Nielsen’s model yielded the smallest error between the predicted and experimental values. The second part of this project consisted of the development of a curriculum in Fuel Cell and Hydrogen Technologies to address different educational barriers identified by the Department of Energy. By the creation of new courses and enterprise programs in the areas of fuel cells and the use of hydrogen as an energy carrier, we introduced engineering students to the new technologies, policies and challenges present with this alternative energy. Feedback provided by students participating in these courses and enterprise programs indicate positive acceptance of the different educational tools. Results obtained from a survey applied to students after participating in these courses showed an increase in the knowledge and awareness of energy fundamentals, which indicates the modules developed in this project are effective in introducing students to alternative energy sources.

Mechanical and Electrical Properties of Single-walled Carbon Nanotubes Synthesized by Chemical Vapor Deposition

Despite the tremendous application potentials of carbon nanotubes (CNTs) proposed by researchers in the last two decades, efficient experimental techniques and methods are still in need for controllable production of CNTs in large scale, and for conclusive characterizations of their properties in order to apply CNTs in high accuracy engineering. In this dissertation, horizontally well-aligned high quality single-walled carbon nanotubes (SWCNTs) have been successfully synthesized on St-cut quartz substrate by chemical vapor deposition (CVD). Effective radial moduli (Eradial) of these straight SWCNTs have been measured by using well-calibrated tapping mode and contact mode atomic force microscopy (AFM). It was found that the measured Eradial decreased from 57 to 9 GPa as the diameter of the SWCNTs increased from 0.92 to 1.91 nm. The experimental results were consistent with the recently reported theoretical simulation data. The method used in this mechanical property test can be easily applied to measure the mechanical properties of other low-dimension nanostructures, such as nanowires and nanodots. The characterized sample is also an ideal platform for electrochemical tests. The electrochemical activities of redox probes Fe(CN)63-/4-, Ru(NH3)63+, Ru(bpy)32+ and protein cytochrome c have been studied on these pristine thin films by using aligned SWCNTs as working electrodes. A simple and high performance electrochemical sensor was fabricated. Flow sensing capability of the device has been tested for detecting neurotransmitter dopamine at physiological conditions with the presence of Bovine serum albumin. Good sensitivity, fast response, high stability and anti-fouling capability were observed. Therefore, the fabricated sensor showed great potential for sensing applications in complicated solution.

Meshfree Method for Prediction of Thermal Properties of Porous Ceramic Materials

In the presented thesis work, meshfree method with distance fields is applied to create a novel computational approach which enables inclusion of the realistic geometric models of the microstructure and liberates Finite Element Analysis(FEA) from thedependance on and limitations of meshing of fine microstructural feature such as splats and porosity.Manufacturing processes of ceramics produce materials with complex porosity microstructure.Geometry of pores, their size and location substantially affect macro scale physical properties of the material. Complex structure and geometry of the pores severely limit application of modern Finite Element Analysis methods because they require construction of spatial grids (meshes) that conform to the geometric shape of the structure. As a result, there are virtually no effective tools available for predicting overall mechanical and thermal properties of porous materials based on their microstructure. This thesis is a separate handling and controls of geometric and physical computational models that are seamlessly combined at solution run time. Using the proposedapproach we will determine the effective thermal conductivity tensor of real porous ceramic materials featuring both isotropic and anisotropic thermal properties. This work involved development and implementation of numerical algorithms, data structure, and software.

Solar and thermal radiative effects during the 2011 extreme desert dust episode over Portugal

This paper analyses the influence of the extreme Saharan desert dust (DD) event on shortwave (SW) and longwave (LW) radiation at the EARLINET/AERONET Évora station (Southern Portugal) from 4 up to 7 April 2011. There was also some cloud occurrence in the period. In this context, it is essential to quantify the effect of cloud presence on aerosol radiative forcing. A radiative transfer model was initialized with aerosol optical properties, cloud vertical properties and meteorological atmospheric vertical profiles. The intercomparison between the instantaneous TOA shortwave and longwave fluxes derived using CERES and those calculated using SBDART, which was fed with aerosol extinction coefficients derived from the CALIPSO and lidar-PAOLI observations, varying OPAC dataset parameters, was reasonably acceptable within the standard deviations. The dust aerosol type that yields the best fit was found to be the mineral accumulation mode. Therefore, SBDART model constrained with the CERES observations can be used to reliably determine aerosol radiative forcing and heating rates. Aerosol radiative forcings and heating rates were derived in the SW (ARFSw, AHRSw) and LW (ARFLw, AHRLw) spectral ranges, considering a cloud-aerosol free reference atmosphere. We found that AOD at 440 nm increased by a factor of 5 on 6 April with respect to the lower dust load on 4 April. It was responsible by a strong cooling radiative effect pointed out by the ARFSw value (−99 W/m2 for a solar zenith angle of 60°) offset by a warming radiative effect according to ARFLw value (+21.9 W/m2) at the surface. Overall, about 24% and 12% of the dust solar radiative cooling effect is compensated by its longwave warming effect at the surface and at the top of the atmosphere, respectively. Hence, larger aerosol loads could enhance the response between the absorption and re-emission processes increasing the ARFLw with respect to those associated with moderate and low aerosol loads. The unprecedented results derived from this work complement the findings in other regions on the modifications of radiative energy budget by the dust aerosols, which could have relevant influences on the regional climate and will be topics for future investigations.

Mesoporous Carbon as effective and sustainable catalyst for fine chemistry

It is well known that activated carbon with welldeveloped porosity is a promising material that have been used for several applications, from adsorption to catalysis. Research in this field has intensified in recent years, looking for new and improved characteristics and applications. Our research group, recently renamed Materials for Adsorption and Catalysis group (MAC) in LAQV-REQUIMTE, has also devoted many research work in this subject, and has developed several collaboration works with other national and international research groups in the field. Among our research group interests there is the study of catalytic properties of carbon materials and specifically mesoporous carbon. Some of the promising results were selected and summarized here, demonstrating that mesoporous carbon is an efficient and environmentally friendly heterogeneous catalyst.

Emerging plant-based proteins: comparison from extraction to functional properties and food application

The increasing demand for alternatives to meat food products, which is linked to ethical and environmental reasons, highlights the necessity of using different protein sources. Plant proteins provide a valid option, thanks to the relative low costs, high availability and wide supply sources. The current process used to produce plant concentrates and isolates is the alkaline extraction followed by isoelectric precipitation. However, despite the high purity of the proteins, it presents some drawbacks. Innovative protein extraction processes are emerging, with the aim of reducing the environmental impact and the costs, as well as improving the functional properties. In this study, the traditional wet protein extraction and another simplified wet process were used to obtain protein-rich extracts out of different plants. The sources considered in the project were de-oiled sunflower and canola, chickpea, lentils, and the camelina meal, an emerging oleaginous seed interesting for its high content of omega 3. The extracts obtained from the two processes were then analysed for their capacities to hold water and fat, to form gel and a stable foam. Results highlighted strong differences concerning the protein content, yield and functionalities. The extracts obtained with the alkaline process confirmed the literature data about the four plant sources (sunflower, canola, chickpea and lentils) and allow to obtain a camelina concentrate with a protein content of 63 % and a protein recovery of 41 %. The second easiest process was not effective to obtain a protein enrichment in oleaginous sources, whereas an enrichment of 10 and 15 % was obtained in chickpea and lentils, respectively. The functional properties were also completely different: the easiest process produced protein ingredients completely water-soluble at pH 7, with a discrete foaming capacity compared to the extracts obtained with alkaline process. These characteristics could make these extracts suitable for the plant milk-analogue products.

CO2 utilization and alternative solvents: effective tools for sustainable applications

The growing concentration of CO2 in the atmosphere and its harmful consequences has led the scientific community to direct its efforts towards sustainable processes. Among the possible approaches, the use of CO2 and alternative solvents are two strategies that are having widespread diffusion. In this work the reuse of CO2 is expressed by using it as a reaction reagent and as trigger to change the physical properties of a catalyst thus facilitating its recovery. As regards the CO2 use as reagent, two catalytic systems have been developed for the conversion of CO2 and epoxides into cyclic carbonates, used in the synthesis of polymers and as aprotic solvents. Homogeneous catalysts made by choline-based eutectic mixtures and heterogeneous catalysts made from biopolymers and waste pyrolysis have been synthesized and tested on this reaction. The carbonate interchange reaction (CIR) of a diol with a linear carbonate (as dimethyl carbonate) is an interesting alternative, for the synthesis of cyclic carbonates; as the second application of CO2 as polarity trigger, it was used for catalyst recovery. In fact DBU, here used as catalyst, is part of the so called “switchable solvents”: they can pass from a less-polar to a more-polar form (and from being soluble to non-soluble in the reaction mixture) when reacting with CO2 in presence of water or alcohols. Also in this case, heterogeneous catalysts made from biopolymers and waste pyrolysis have been synthesized and tested on CIR. As for the use of alternative solvents, this work focuses on the use of Deep Eutectic Solvents (DESs). They are a new generation of solvents composed by a mixture of two or more substances, liquid at room temperature, and non-volatile. New and biobased DESs were here used: i) as reaction media to carry out chemoenzymatic epoxidation; ii) in the extraction of astaxanthin from microalgae culture.

The Crosslinking Degree Controls The Mechanical, Rheological, And Swelling Properties Of Hyaluronic Acid Microparticles.

Viscosupplements, used for treating joint and cartilage diseases, restore the rheological properties of synovial fluid, regulate joint homeostasis and act as scaffolds for cell growth and tissue regeneration. Most viscosupplements are hydrogels composed of hyaluronic acid (HA) microparticles suspended in fluid HA. These microparticles are crosslinked with chemicals to assure their stability against enzyme degradation and to prolong the action of the viscosupplement. However, the crosslinking also modifies the mechanical, swelling and rheological properties of the HA microparticle hydrogels, with consequences on the effectiveness of the application. The aim of this study is to correlate the crosslinking degree (CD) with these properties to achieve modulation of HA/DVS microparticles through CD control. Because divinyl sulfone (DVS) is the usual crosslinker of HA in viscosupplements, we examined the effects of CD by preparing HA microparticles at 1:1, 2:1, 3:1, and 5:1 HA/DVS mass ratios. The CD was calculated from inductively coupled plasma spectrometry data. HA microparticles were previously sized to a mean diameter of 87.5 µm. Higher CD increased the viscoelasticity and the extrusion force and reduced the swelling of the HA microparticle hydrogels, which also showed Newtonian pseudoplastic behavior and were classified as covalent weak. The hydrogels were not cytotoxic to fibroblasts according to an MTT (3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyltetrazolium bromide) assay. © 2014 Wiley Periodicals, Inc. J Biomed Mater Res Part A, 2014.

Psychometric Properties Evaluation Of A New Ergonomics-related Job Factors Questionnaire Developed For Nursing Workers.

The objectives of this study were to develop a questionnaire that evaluates the perception of nursing workers to job factors that may contribute to musculoskeletal symptoms, and to evaluate its psychometric properties. Internationally recommended methodology was followed: construction of domains, items and the instrument as a whole, content validity, and pre-test. Psychometric properties were evaluated among 370 nursing workers. Construct validity was analyzed by the factorial analysis, known-groups technique, and convergent validity. Reliability was assessed through internal consistency and stability. Results indicated satisfactory fit indices during confirmatory factor analysis, significant difference (p < 0.01) between the responses of nursing and office workers, and moderate correlations between the new questionnaire and Numeric Pain Scale, SF-36 and WRFQ. Cronbach's alpha was close to 0.90 and ICC values ranged from 0.64 to 0.76. Therefore, results indicated that the new questionnaire had good psychometric properties for use in studies involving nursing workers.