Sperimentazione di algoritmi di localizzazione per sorgenti acustiche

L'obiettivo di questo elaborato è quello di realizzare un sistema di acquisizione real-time e low cost, in grado di stimare la posizione di una sorgente sonora. Per acquisizione real-time si intende un sistema in grado di seguire gli spostamenti della sorgente audio nell'ambiente, limitando il più possibile i tempi di latenza fra un'acquisizione e l'altra. A tal fine si sfrutteranno due coppie di microfoni, che concorrereranno in maniera sequenziale alla stima dell'angolo di arrivo del suono (e quindi della retta su cui giace il punto di provenienza del suono). Combinando i dati raccolti dai quattro microfoni sarà dunque possibile risalire alla posizione di provenienza della sorgente sonora. Il software (implementato in MATLAB) verrà ampiamente discusso nei seguenti capitoli, il suo scopo sarà quello di gestire l'acquisizione dati, garantire il funzionamento real-time e fornire una stima di posizione della sorgente sonora, mostrando il relativo errore commesso durante la misura, nel caso in cui si conosca a priori la posizione della sorgente.

DEVELOPMENT OF A HUMANOID ROBOT ARM FOR USE IN URBAN ENVIRONMENTS

The Bucknell Humanoid Robot Arm project was developed in order toprovide a lightweight robotic arm for the IHMC / Bucknell University bipedal robot that will provide a means of manipulation and facilitate operations in urban environments. The resulting fabricated arm described in this thesis weighs only 13 pounds, and is capable of holding 11 pounds fully outstretched, lifting objects such as tools, and it can open doors. It is also capable of being easily integrated with the IHMC / Bucknell University biped. This thesis provides an introduction to robots themselves, discusses the goals of the Bucknell Humanoid Robot Arm project, provides a background on some of the existing robots, and shows how the Bucknell Humanoid Robot Arm fits in with the studies that have been completed. After reading these studies, important items such as design trees and operational scenarios were completed. The completion of these items led to measurable specifications and later the design requirements and specifications. A significant contribution of this thesis to the robotics discipline involves the design of the actuator itself. The arm uses of individual, lightweight, compactly designed actuators to achieve desired capabilities and performance requirements. Many iterations were completed to get to the final design of each actuator. After completing the actuators, the design of the intermediate links and brackets was finalized. Completion of the design led to the development of a complex controls system which used a combination of Clanguage and Java.

Using Micro-Gravity Techniques to Map Alluvium Thickness and Pleistocene Location of the West Branch of the Susquehanna River Near Muncy, Pennsylvania

Laurentide glaciation during the early Pleistocene (~970 ka) dammed the southeast-flowing West Branch of the Susquehanna River (WBSR), scouring bedrock and creating 100-km-long glacial Lake Lesley near the Great Bend at Muncy, Pennsylvania (Ramage et al., 1998). Local drill logs and well data indicate that subsequent paleo-outwash floods and modern fluvial processes have deposited as much as 30 meters of alluvium in this area, but little is known about the valley fill architecture and the bedrock-alluvium interface. By gaining a greater understanding of the bedrock-alluvium interface the project will not only supplement existing depth to bedrock information, but also provide information pertinent to the evolution of the Muncy Valley landscape. This project determined if variations in the thickness of the valley fill were detectable using micro-gravity techniques to map the bedrock-alluvium interface. The gravity method was deemed appropriate due to scale of the study area (~30 km2), ease of operation by a single person, and the available geophysical equipment. A LaCoste and Romberg Gravitron unit was used to collect gravitational field readings at 49 locations over 5 transects across the Muncy Creek and Susquehanna River valleys (approximately 30 km2), with at least two gravity base stations per transect. Precise latitude, longitude and ground surface elevation at each location were measured using an OPUS corrected Trimble RTK-GPS unit. Base stations were chosen based on ease of access due to the necessity of repeat measurements. Gravity measurement locations were selected and marked to provide easy access and repeat measurements. The gravimeter was returned to a base station within every two hours and a looping procedure was used to determine drift and maximize confidence in the gravity measurements. A two-minute calibration reading at each station was used to minimize any tares in the data. The Gravitron digitally recorded finite impulse response filtered gravity measurements every 20 seconds at each station. A measurement period of 15 minutes was used for each base station occupation and a minimum of 5 minutes at all other locations. Longer or multiple measurements were utilized at some sites if drift or other externalities (i.e. train or truck traffic) were effecting readings. Average, median, standard deviation and 95% confidence interval were calculated for each station. Tidal, drift, latitude, free-air, Bouguer and terrain corrections were then applied. The results show that the gravitational field decreases as alluvium thickness increases across the axes of the Susquehanna River and Muncy Creek valleys. However, the location of the gravity low does not correspond with the present-day location of the West Branch of the Susquehanna River (WBSR), suggesting that the WBSR may have been constrained along Bald Eagle Mountain by a glacial lobe originating from the Muncy Creek Valley to the northeast. Using a 3-D inversion model, the topography of the bedrock-alluvium interface was determined over the extent of the study area using a density contrast of -0.8 g/cm3. Our results are consistent with the bedrock geometry of the area, and provide a low-cost, non-invasive and efficient method for exploring the subsurface and for supplementing existing well data.

Generic detection of coronaviruses and differentiation at the prototype strain level by reverse transcription-PCR and nonfluorescent low-density microarray

A nonfluorescent low-cost, low-density oligonucleotide array was designed for detecting the whole coronavirus genus after reverse transcription (RT)-PCR. The limit of detection was 15.7 copies/reaction. The clinical detection limit in patients with severe acute respiratory syndrome was 100 copies/sample. In 39 children suffering from coronavirus 229E, NL63, OC43, or HKU1, the sensitivity was equal to that of individual real-time RT-PCRs.

Design and implementation of a 3D computer game controller using inertial MEMS sensors

Though 3D computer graphics has seen tremendous advancement in the past two decades, most available mechanisms for computer interaction in 3D are high cost and targeted for industry and virtual reality applications. Recent advances in Micro-Electro-Mechanical-System (MEMS) devices have brought forth a variety of new low-cost, low-power, miniature sensors with high accuracy, which are well suited for hand-held devices. In this work a novel design for a 3D computer game controller using inertial sensors is proposed, and a prototype device based on this design is implemented. The design incorporates MEMS accelerometers and gyroscopes from Analog Devices to measure the three components of the acceleration and angular velocity. From these sensor readings, the position and orientation of the hand-held compartment can be calculated using numerical methods. The implemented prototype is utilizes a USB 2.0 compliant interface for power and communication with the host system. A Microchip dsPIC microcontroller is used in the design. This microcontroller integrates the analog to digital converters, the program memory flash, as well as the core processor, on a single integrated circuit. A PC running Microsoft Windows operating system is used as the host machine. Prototype firmware for the microcontroller is developed and tested to establish the communication between the design and the host, and perform the data acquisition and initial filtering of the sensor data. A PC front-end application with a graphical interface is developed to communicate with the device, and allow real-time visualization of the acquired data.

Structural and surface property characterization of titanium dioxide nanotubes for orthopedic implants

This research focused on the to modification of the surface structure of titanium implants with nanostructured morphology of TiO2 nanotubes and studied the interaction of nanotubes with osteoblast cells to understand the parameters that affect the cell growth. The electrical, mechanical, and structural properties of TiO2 nanotubes were characterized to establish a better understanding on the properties of such nanoscale morphological structures. To achieve the objectives of this research work I transformed the titanium and its alloys, either in bulk sheet form, bulk machined form, or thin film deposited on another substrate into a surface of titania nanotubes using a low cost and environmentally friendly process. The process requires only a simple electrolyte, low cost electrode, and a DC power supply. With this simple approach of scalable nanofabrication, a typical result is nanotubes that are each approximately 100nm in diameter and have a wall thickness of about 20nm. By changing the fabrication parameters, independent nanotubes can be fabricated with open volume between them. Titanium in this form is termed onedimensional since electron transport is narrowly confined along the length of the nanotube. My Ph.D. accomplishments have successfully shown that osteoblast cells, the cells that are the precursors to bone, have a strong tendency to attach to the inside and outside of the titanium nanotubes onto which they are grown using their filopodia – cell’s foot used for locomotion – anchored to titanium nanotubes. In fact it was shown that the cell prefers to find many anchoring sites. These sites are critical for cell locomotion during the first several weeks of maturity and upon calcification as a strongly anchored bone cell. In addition I have shown that such a surface has a greater cell density than a smooth titanium surface. My work also developed a process that uses a focused and controllably rastered ion beam as a nano-scalpel to cut away sections of the osteoblast cells to probe the attachment beneath the main cell body. Ultimately the more rapid growth of osteoblasts, coupled with a stronger cell-surface interface, could provide cost reduction, shorter rehabilitation, and fewer follow-on surgeries due to implant loosening.

The Cost-Effectiveness of Monitoring Strategies for Antiretroviral Therapy of HIV Infected Patients in Resource-Limited Settings: Software Tool.

BACKGROUND The cost-effectiveness of routine viral load (VL) monitoring of HIV-infected patients on antiretroviral therapy (ART) depends on various factors that differ between settings and across time. Low-cost point-of-care (POC) tests for VL are in development and may make routine VL monitoring affordable in resource-limited settings. We developed a software tool to study the cost-effectiveness of switching to second-line ART with different monitoring strategies, and focused on POC-VL monitoring. METHODS We used a mathematical model to simulate cohorts of patients from start of ART until death. We modeled 13 strategies (no 2nd-line, clinical, CD4 (with or without targeted VL), POC-VL, and laboratory-based VL monitoring, with different frequencies). We included a scenario with identical failure rates across strategies, and one in which routine VL monitoring reduces the risk of failure. We compared lifetime costs and averted disability-adjusted life-years (DALYs). We calculated incremental cost-effectiveness ratios (ICER). We developed an Excel tool to update the results of the model for varying unit costs and cohort characteristics, and conducted several sensitivity analyses varying the input costs. RESULTS Introducing 2nd-line ART had an ICER of US$1651-1766/DALY averted. Compared with clinical monitoring, the ICER of CD4 monitoring was US$1896-US$5488/DALY averted and VL monitoring US$951-US$5813/DALY averted. We found no difference between POC- and laboratory-based VL monitoring, except for the highest measurement frequency (every 6 months), where laboratory-based testing was more effective. Targeted VL monitoring was on the cost-effectiveness frontier only if the difference between 1st- and 2nd-line costs remained large, and if we assumed that routine VL monitoring does not prevent failure. CONCLUSION Compared with the less expensive strategies, the cost-effectiveness of routine VL monitoring essentially depends on the cost of 2nd-line ART. Our Excel tool is useful for determining optimal monitoring strategies for specific settings, with specific sex-and age-distributions and unit costs.

A cost-effective surgical navigation solution for periacetabular osteotomy (PAO) surgery

In this chapter a low-cost surgical navigation solution for periacetabular osteotomy (PAO) surgery is described. Two commercial inertial measurement units (IMU, Xsens Technologies, The Netherlands), are attached to a patient’s pelvis and to the acetabular fragment, respectively. Registration of the patient with a pre-operatively acquired computer model is done by recording the orientation of the patient’s anterior pelvic plane (APP) using one IMU. A custom-designed device is used to record the orientation of the APP in the reference coordinate system of the IMU. After registration, the two sensors are mounted to the patient’s pelvis and acetabular fragment, respectively. Once the initial position is recorded, the orientation is measured and displayed on a computer screen. A patient-specific computer model generated from a pre-operatively acquired computed tomography (CT) scan is used to visualize the updated orientation of the acetabular fragment. Experiments with plastic bones (7 hip joints) performed in an operating room comparing a previously developed optical navigation system with our inertial-based navigation system showed no statistical difference on the measurement of acetabular component reorientation (anteversion and inclination). In six out of seven hip joints the mean absolute difference was below five degrees for both anteversion and inclination.

A cost-effective surgical navigation solution for periacetabular osteotomy (PAO) surgery.

PURPOSE To evaluate a low-cost, inertial sensor-based surgical navigation solution for periacetabular osteotomy (PAO) surgery without the line-of-sight impediment. METHODS Two commercial inertial measurement units (IMU, Xsens Technologies, The Netherlands), are attached to a patient's pelvis and to the acetabular fragment, respectively. Registration of the patient with a pre-operatively acquired computer model is done by recording the orientation of the patient's anterior pelvic plane (APP) using one IMU. A custom-designed device is used to record the orientation of the APP in the reference coordinate system of the IMU. After registration, the two sensors are mounted to the patient's pelvis and acetabular fragment, respectively. Once the initial position is recorded, the orientation is measured and displayed on a computer screen. A patient-specific computer model generated from a pre-operatively acquired computed tomography scan is used to visualize the updated orientation of the acetabular fragment. RESULTS Experiments with plastic bones (eight hip joints) performed in an operating room comparing a previously developed optical navigation system with our inertial-based navigation system showed no statistically significant difference on the measurement of acetabular component reorientation. In all eight hip joints the mean absolute difference was below four degrees. CONCLUSION Using two commercially available inertial measurement units we show that it is possible to accurately measure the orientation (inclination and anteversion) of the acetabular fragment during PAO surgery and therefore to successfully eliminate the line-of-sight impediment that optical navigation systems have.

A comparative review of water disinfection methods appropriate for developing countries and their efficacy, cost-efficiency, and usability

Developing countries are heavily burdened by limited access to safe drinking water and subsequent water-related diseases. Numerous water treatment interventions combat this public health crisis, encompassing both traditional and less-common methods. Of these, water disinfection serves as an important means to provide safe drinking water. Existing literature discusses a wide range of traditional treatment options and encourages the use of multi-barrier approaches including coagulation-flocculation, filtration, and disinfection. Most sources do not delve into approaches specifically appropriate for developing countries, nor do they exclusively examine water disinfection methods.^ The objective of this review is to focus on an extensive range of chemical, physio-chemical, and physical water disinfection techniques to provide a compilation, description and evaluation of options available. Such an objective provides further understanding and knowledge to better inform water treatment interventions and explores alternate means of water disinfection appropriate for developing countries. Appropriateness for developing countries corresponds to the effectiveness of an available, easy to use disinfection technique at providing safe drinking water at a low cost.^ Among chemical disinfectants, SWS sodium hypochlorite solution is preferred over sodium hypochlorite bleach due to consistent concentrations. Tablet forms are highly recommended chemical disinfectants because they are effective and very easy to use, but also because they are stable. Examples include sodium dichloroisocyanurate, calcium hypochlorite, and chlorine dioxide, which vary in cost depending on location and availability. Among physio-chemical disinfection options, electrolysis which produces mixed oxidants (MIOX) provides a highly effective disinfection option with a higher upfront cost but very low cost over the long term. Among physical disinfection options, solar disinfection (SODIS) applications are effective, but they treat only a fixed volume of water at a time. They come with higher initial costs but very low on-going costs. Additional effective disinfection techniques may be suitable depending on the location, availability and cost.^

The determinants of improvements in health outcomes and of cost reduction in hospital inpatient care

This study aims to address two research questions. First, ‘Can we identify factors that are determinants both of improved health outcomes and of reduced costs for hospitalized patients with one of six common diagnoses?’ Second, ‘Can we identify other factors that are determinants of improved health outcomes for such hospitalized patients but which are not associated with costs?’ The Healthcare Cost and Utilization Project (HCUP) Nationwide Inpatient Sample (NIS) database from 2003 to 2006 was employed in this study. The total study sample consisted of hospitals which had at least 30 patients each year for the given diagnosis: 954 hospitals for acute myocardial infarction (AMI), 1552 hospitals for congestive heart failure (CHF), 1120 hospitals for stroke (STR), 1283 hospitals for gastrointestinal hemorrhage (GIH), 979 hospitals for hip fracture (HIP), and 1716 hospitals for pneumonia (PNE). This study used simultaneous equations models to investigate the determinants of improvement in health outcomes and of cost reduction in hospital inpatient care for these six common diagnoses. In addition, the study used instrumental variables and two-stage least squares random effect model for unbalanced panel data estimation. The study concluded that a few factors were determinants of high quality and low cost. Specifically, high specialty was the determinant of high quality and low costs for CHF patients; small hospital size was the determinant of high quality and low costs for AMI patients. Furthermore, CHF patients who were treated in Midwest, South, and West region hospitals had better health outcomes and lower hospital costs than patients who were treated in Northeast region hospitals. Gastrointestinal hemorrhage and pneumonia patients who were treated in South region hospitals also had better health outcomes and lower hospital costs than patients who were treated in Northeast region hospitals. This study found that six non-cost factors were related to health outcomes for a few diagnoses: hospital volume, percentage emergency room admissions for a given diagnosis, hospital competition, specialty, bed size, and hospital region.^

Cost and energy efficient reconfigurable embedded platform using Spartan-6 FPGAs

Modern FPGAs with run-time reconfiguration allow the implementation of complex systems offering both the flexibility of software-based solutions combined with the performance of hardware. This combination of characteristics, together with the development of new specific methodologies, make feasible to reach new points of the system design space, and make embedded systems built on these platforms acquire more and more importance. However, the practical exploitation of this technique in fields that traditionally have relied on resource restricted embedded systems, is mainly limited by strict power consumption requirements, the cost and the high dependence of DPR techniques with the specific features of the device technology underneath. In this work, we tackle the previously reported problems, designing a reconfigurable platform based on the low-cost and low-power consuming Spartan-6 FPGA family. The full process to develop the platform will be detailed in the paper from scratch. In addition, the implementation of the reconfiguration mechanism, including two profiles, is reported. The first profile is a low-area and low-speed reconfiguration engine based mainly on software functions running on the embedded processor, while the other one is a hardware version of the same engine, implemented in the FPGA logic. This reconfiguration hardware block has been originally designed to the Virtex-5 family, and its porting process will be also described in this work, facing the interoperability problem among different families.

Digital Control Implementation to Reduce the Cost and Improve the Performance of the Control Stage of an Industrial Switched-Mode Power Supply

The main objective of this work is the design and implementation of the digital control stage of a 280W AC/DC industrial power supply in a single low-cost microcontroller to replace the analog control stage. The switch-mode power supply (SMPS) consists of a PFC boost converter with fixed frequency operation and a variable frequency LLC series resonant DC/DC converter. Input voltage range is 85VRMS-550VRMS and the output voltage range is 24V-28V. A digital controller is especially suitable for this kind of SMPS to implement its multiple functionalities and to keep the efficiency and the performance high over the wide range of input voltages. Additional advantages of the digital control are reliability and size. The optimized design and implementation of the digital control stage it is presented. Experimental results show the stable operation of the controlled system and an estimation of the cost reduction achieved with the digital control stage.

Implementación de Algoritmos de Procesado de Señal sobre FPGA: Especificación, Reutilización y Exploración del Espacio de Diseño

Esta Tesis aborda el diseño e implementación de aplicaciones en el campo de procesado de señal, utilizando como plataforma los dispositivos reconfigurables FPGA. Esta plataforma muestra una alta capacidad de lógica, e incorpora elementos orientados al procesado de señal, que unido a su relativamente bajo coste, la hacen ideal para el desarrollo de aplicaciones de procesado de señal cuando se requiere realizar un procesado intensivo y se buscan unas altas prestaciones. Sin embargo, el coste asociado al desarrollo en estas plataformas es elevado. Mientras que el aumento en la capacidad lógica de los dispositivos FPGA permite el desarrollo de sistemas completos, los requisitos de altas prestaciones obligan a que en muchas ocasiones se deban optimizar operadores a muy bajo nivel. Además de las restricciones temporales que imponen este tipo de aplicaciones, también tienen asociadas restricciones de área asociadas al dispositivo, lo que obliga a evaluar y verificar entre diferentes alternativas de implementación. El ciclo de diseño e implementación para estas aplicaciones se puede prolongar tanto, que es normal que aparezcan nuevos modelos de FPGA, con mayor capacidad y mayor velocidad, antes de completar el sistema, y que hagan a las restricciones utilizadas para el diseño del sistema inútiles. Para mejorar la productividad en el desarrollo de estas aplicaciones, y con ello acortar su ciclo de diseño, se pueden encontrar diferentes métodos. Esta Tesis se centra en la reutilización de componentes hardware previamente diseñados y verificados. Aunque los lenguajes HDL convencionales permiten reutilizar componentes ya definidos, se pueden realizar mejoras en la especificación que simplifiquen el proceso de incorporar componentes a nuevos diseños. Así, una primera parte de la Tesis se orientará a la especificación de diseños basada en componentes predefinidos. Esta especificación no sólo busca mejorar y simplificar el proceso de añadir componentes a una descripción, sino que también busca mejorar la calidad del diseño especificado, ofreciendo una mayor posibilidad de configuración e incluso la posibilidad de informar de características de la propia descripción. Reutilizar una componente ya descrito depende en gran medida de la información que se ofrezca para su integración en un sistema. En este sentido los HDLs convencionales únicamente proporcionan junto con la descripción del componente la interfaz de entrada/ salida y un conjunto de parámetros para su configuración, mientras que el resto de información requerida normalmente se acompaña mediante documentación externa. En la segunda parte de la Tesis se propondrán un conjunto de encapsulados cuya finalidad es incorporar junto con la propia descripción del componente, información que puede resultar útil para su integración en otros diseños. Incluyendo información de la implementación, ayuda a la configuración del componente, e incluso información de cómo configurar y conectar al componente para realizar una función. Finalmente se elegirá una aplicación clásica en el campo de procesado de señal, la transformada rápida de Fourier (FFT), y se utilizará como ejemplo de uso y aplicación, tanto de las posibilidades de especificación como de los encapsulados descritos. El objetivo del diseño realizado no sólo mostrará ejemplos de la especificación propuesta, sino que también se buscará obtener una implementación de calidad comparable con resultados de la literatura. Para ello, el diseño realizado se orientará a su implementación en FPGA, aprovechando tanto los elementos lógicos generalistas como elementos específicos de bajo nivel disponibles en estos dispositivos. Finalmente, la especificación de la FFT obtenida se utilizará para mostrar cómo incorporar en su interfaz información que ayude para su selección y configuración desde fases tempranas del ciclo de diseño. Abstract This PhD. thesis addresses the design and implementation of signal processing applications using reconfigurable FPGA platforms. This kind of platform exhibits high logic capability, incorporates dedicated signal processing elements and provides a low cost solution, which makes it ideal for the development of signal processing applications, where intensive data processing is required in order to obtain high performance. However, the cost associated to the hardware development on these platforms is high. While the increase in logic capacity of FPGA devices allows the development of complete systems, high-performance constraints require the optimization of operators at very low level. In addition to time constraints imposed by these applications, Area constraints are also applied related to the particular device, which force to evaluate and verify a design among different implementation alternatives. The design and implementation cycle for these applications can be tedious and long, being therefore normal that new FPGA models with a greater capacity and higher speed appear before completing the system implementation. Thus, the original constraints which guided the design of the system become useless. Different methods can be used to improve the productivity when developing these applications, and consequently shorten their design cycle. This PhD. Thesis focuses on the reuse of hardware components previously designed and verified. Although conventional HDLs allow the reuse of components already defined, their specification can be improved in order to simplify the process of incorporating new design components. Thus, a first part of the PhD. Thesis will focus on the specification of designs based on predefined components. This specification improves and simplifies the process of adding components to a description, but it also seeks to improve the quality of the design specified with better configuration options and even offering to report on features of the description. Hardware reuse of a component for its integration into a system largely depends on the information it offers. In this sense the conventional HDLs only provide together with the component description, the input/output interface and a set of parameters for its configuration, while other information is usually provided by external documentation. In the second part of the Thesis we will propose a formal way of encapsulation which aims to incorporate with the component description information that can be useful for its integration into other designs. This information will include features of the own implementation, but it will also support component configuration, and even information on how to configure and connect the component to carry out a function. Finally, the fast Fourier transform (FFT) will be chosen as a well-known signal processing application. It will be used as case study to illustrate the possibilities of proposed specification and encapsulation formalisms. The objective of the FFT design is not only to show practical examples of the proposed specification, but also to obtain an implementation of a quality comparable to scientific literature results. The design will focus its implementation on FPGA platforms, using general logic elements as base of the implementation, but also taking advantage of low-level specific elements available on these devices. Last, the specification of the obtained FFT will be used to show how to incorporate in its interface information to assist in the selection and configuration process early in the design cycle.

Towards a ground navigation system based in visual feedback provided by a mini UAV

This paper addresses initial efforts to develop a navigation system for ground vehicles supported by visual feedback from a mini aerial vehicle. A visual-based algorithm computes the ground vehicle pose in the world frame, as well as possible obstacles within the ground vehicle pathway. Relying on that information, a navigation and obstacle avoidance system is used to re-plan the ground vehicle trajectory, ensuring an optimal detour. Finally, some experiments are presented employing a unmanned ground vehicle (UGV) and a low cost mini unmanned aerial vehicle (UAV).