Fault detection, diagnosis and active fault tolerant control for a satellite attitude control system

Modern control systems are becoming more and more complex and control algorithms more and more sophisticated. Consequently, Fault Detection and Diagnosis (FDD) and Fault Tolerant Control (FTC) have gained central importance over the past decades, due to the increasing requirements of availability, cost efficiency, reliability and operating safety. This thesis deals with the FDD and FTC problems in a spacecraft Attitude Determination and Control System (ADCS). Firstly, the detailed nonlinear models of the spacecraft attitude dynamics and kinematics are described, along with the dynamic models of the actuators and main external disturbance sources. The considered ADCS is composed of an array of four redundant reaction wheels. A set of sensors provides satellite angular velocity, attitude and flywheel spin rate information. Then, general overviews of the Fault Detection and Isolation (FDI), Fault Estimation (FE) and Fault Tolerant Control (FTC) problems are presented, and the design and implementation of a novel diagnosis system is described. The system consists of a FDI module composed of properly organized model-based residual filters, exploiting the available input and output information for the detection and localization of an occurred fault. A proper fault mapping procedure and the nonlinear geometric approach are exploited to design residual filters explicitly decoupled from the external aerodynamic disturbance and sensitive to specific sets of faults. The subsequent use of suitable adaptive FE algorithms, based on the exploitation of radial basis function neural networks, allows to obtain accurate fault estimations. Finally, this estimation is actively exploited in a FTC scheme to achieve a suitable fault accommodation and guarantee the desired control performances. A standard sliding mode controller is implemented for attitude stabilization and control. Several simulation results are given to highlight the performances of the overall designed system in case of different types of faults affecting the ADCS actuators and sensors.

Dynamics and control issues of multi-rotor platforms

This thesis deals with the analytic study of dynamics of Multi--Rotor Unmanned Aerial Vehicles. It is conceived to give a set of mathematical instruments apt to the theoretical study and design of these flying machines. The entire work is organized in analogy with classical academic texts about airplane flight dynamics. First, the non--linear equations of motion are defined and all the external actions are modeled, with particular attention to rotors aerodynamics. All the equations are provided in a form, and with personal expedients, to be directly exploitable in a simulation environment. This has requited an answer to questions like the trim of such mathematical systems. All the treatment is developed aiming at the description of different multi--rotor configurations. Then, the linearized equations of motion are derived. The computation of the stability and control derivatives of the linear model is carried out. The study of static and dynamic stability characteristics is, thus, addressed, showing the influence of the various geometric and aerodynamic parameters of the machine and in particular of the rotors. All the theoretic results are finally utilized in two interesting cases. One concerns the design of control systems for attitude stabilization. The linear model permits the tuning of linear controllers gains and the non--linear model allows the numerical testing. The other case is the study of the performances of an innovative configuration of quad--rotor aircraft. With the non--linear model the feasibility of maneuvers impossible for a traditional quad--rotor is assessed. The linear model is applied to the controllability analysis of such an aircraft in case of actuator block.

Aufbau hochfunktionaler Intralogistik-Knoten mittels kleinskaliger Module als Cognitive Conveyor

Kleinskalige, multifunktionale Module haben ein hohes Potential bei der wirtschaftlichen und flexiblen Gestaltung intralogistischer Systeme mit hoher Funktionalität. Durch dezentrale Steuerung und eigener Intelligenz der Module ist das System frei skalierbar und der Installationsaufwand wird minimiert. Mittels eines neuartigen Konzeptes der Datenkommunikation für Stetigförderer erfolgt der Informationsaustausch drahtlos mit Hilfe optoelektrischer Elemente. Die Kleinskaligkeit der Transportmodule gegenüber der Transporteinheit im Zusammenhang mit dem Steuerungskonzept erlaubt eine selektive Beschaltung der Module nach Bedarf und damit eine optimierte Energieausnutzung im Betrieb. Prototypen auf Basis von Schwenkrollen mit integrierter Antriebstechnik und Steuerung lassen das Potential des Prinzips erkennen. Das neu entwickelte Konzept der Schrägscheibe hilft bei der anspruchsvollen Integration der Antriebstechnik in das Modul durch das Prinzip der koaxialen Aktoren. Durch omnidirektionalen Funktionsumfang der Module entsteht im Zusammenschluss zu einer Modulmatrix ein hochflexibel einsetzbares Intralogistik-Modul. Die Vernetzung dieser hochfunktionalen Knoten durch einfache Fördertechnik bietet die Möglichkeit einfacher Planung flexibler Logistiksysteme.

Kollaborative Planung dezentral gesteuerter Materialflusssysteme in der Intralogistik

Der Beitrag stellt eine Kollaborationssoftware vor, die im Rahmen des AiF-Forschungsprojektes „KoDeMat“ entwickelt wurde. Der Fokus wird auf die Problemfelder der fehlenden Standardisierung und Anpassbarkeit im Bereich von fördertechnischen Anlagen gerichtet. Ziel ist, unter Zuhilfenahme von standardisierten, kollaborativen Engineeringprozessen, eine unternehmensübergreifende Planung, Realisierung und einen Umbau von komplexen dezentral gesteuerten Intralogistiksystemen sowie deren Betrieb effizient zu ermöglichen.

Simulation of SLA-based VM-scaling algorithms for cloud-distributed applications

Cloud Computing has evolved to become an enabler for delivering access to large scale distributed applications running on managed network-connected computing systems. This makes possible hosting Distributed Enterprise Information Systems (dEISs) in cloud environments, while enforcing strict performance and quality of service requirements, defined using Service Level Agreements (SLAs). {SLAs} define the performance boundaries of distributed applications, and are enforced by a cloud management system (CMS) dynamically allocating the available computing resources to the cloud services. We present two novel VM-scaling algorithms focused on dEIS systems, which optimally detect most appropriate scaling conditions using performance-models of distributed applications derived from constant-workload benchmarks, together with SLA-specified performance constraints. We simulate the VM-scaling algorithms in a cloud simulator and compare against trace-based performance models of dEISs. We compare a total of three SLA-based VM-scaling algorithms (one using prediction mechanisms) based on a real-world application scenario involving a large variable number of users. Our results show that it is beneficial to use autoregressive predictive SLA-driven scaling algorithms in cloud management systems for guaranteeing performance invariants of distributed cloud applications, as opposed to using only reactive SLA-based VM-scaling algorithms.

A comparative analysis of hospital -based physician monitoring systems

The purpose of the multiple case-study was to determine how hospital subsystems (such as physician monitoring and credentialing; quality assurance; risk management; and peer review) were supporting the monitoring of physicians? Three large metropolitan hospitals in Texas were studied and designated as hospitals #1, #2, and #3. Realizing that hospital subsystems are a unique entity and part of a larger system, conclusions were made on the premises of a quality control system, in relation to the tools of government (particularly the Health Care Quality Improvement Act (HCQIA)), and in relation to itself as a tool of a hospital.^ Three major analytical assessments were performed. First, the subsystems were analyzed as to their "completeness"; secondly, the subsystems were analyzed for "performance"; and thirdly, the subsystems were analyzed in reference to the interaction of completeness and performance.^ The physician credentialing and monitoring and the peer review subsystems as quality control systems were most complete, efficient, and effective in hospitals #1 and #3. The HCQIA did not seem to be an influencing factor in the completeness of the subsystem in hospital #1. The quality assurance and risk management subsystem in hospital #2 was not representative of completeness and performance and the HCQIA was not an influencing factor in the completeness of the Q.A. or R.M. systems in any hospital. The efficiency (computerization) of the physician credentialing, quality assurance and peer review subsystems in hospitals #1 and #3 seemed to contribute to their effectiveness (system-wide effect).^ The results indicated that the more complete, effective, and efficient subsystems were characterized by (1) all defined activities being met, (2) the HCQIA being an influencing factor, (3) a decentralized administrative structure, (4) computerization an important element, and (5) staff was sophisticated in subsystem operations. However, other variables were identified which deserve further research as to their effect on completeness and performance of subsystems. They include (1) medical staff affiliations, (2) system funding levels, (3) the system's administrative structure, and (4) the physician staff "cultural" characteristics. Perhaps by understanding other influencing factors, health care administrators may plan subsystems that will be compatible with legislative requirements and administrative objectives. ^

Design and Test of a High QoS Radio Network for CBTC Systems in Subway Tunnels

Communications Based Train Control Systems require high quality radio data communications for train signaling and control. Actually most of these systems use 2.4GHz band with proprietary radio transceivers and leaky feeder as distribution system. All them demand a high QoS radio network to improve the efficiency of railway networks. We present narrow band, broad band and data correlated measurements taken in Madrid underground with a transmission system at 2.4 GHz in a test network of 2 km length in subway tunnels. The architecture proposed has a strong overlap in between cells to improve reliability and QoS. The radio planning of the network is carefully described and modeled with narrow band and broadband measurements and statistics. The result is a network with 99.7% of packets transmitted correctly and average propagation delay of 20ms. These results fulfill the specifications QoS of CBTC systems.

Spacecraft thermal control design data

This paper shows the actual state of a compilation work on Thermal Control Design Data being done at Madrid (Lamf-ETSIA) under several ESTEC contracts, introducing a Handbook already issued, its additions and updatings.

Bases moleculares de la resistencia a insecticidas en la mosca mediterránea de la fruta Ceratitis Capitata (Wiedemann)

La mosca mediterránea de la fruta Ceratitis capitata (Wiedemann, 1824) está considerada una de las plagas clave para la fruticultura. El malatión es un insecticida organofosforado que fue empleado mayoritariamente en España para el control de C. capitata hasta 2009, año en el que dejó de utilizarse por no estar incluido en el anexo I de la Directiva Europea 91/414/ECC. El incremento del uso del malatión, debido a las graves pérdidas económicas causadas por C. capitata, provocó la aparición de poblaciones de campo resistentes. El estudio de una población resistente a malatión, recogida en Castelló en 2004, permitió la identificación de dos mecanismos de resistencia: una mutación puntual (G328A) en la acetilcolinesterasa (AChE) y un mecanismo de resistencia metabólica, probablemente mediado por carboxilesterasas. Teniendo en cuenta estos antecedentes, nos propusimos estudiar los mecanismos implicados en la resistencia a malatión en C. capitata. Además, durante el desarrollo de esta Tesis, el malatión fue sustituido por otros insecticidas como el espinosad y la lambda-cialotrina para el control de la plaga. En este nuevo contexto, es extremadamente importante analizar la susceptibilidad de poblaciones de campo frente a espinosad y estudiar la posible existencia de resistencia cruzada a estos insecticidas, así como sentar las bases para el estudio de futuros mecanismos de resistencia. En primer lugar, analizamos mediante bioensayos con dosis discriminante la susceptibilidad a malatión y espinosad en doce poblaciones de C. capitata de Andalucía, Aragón, Cataluña, Comunidad Valenciana e Islas Baleares; y nuestros resultados sugirieron la presencia de individuos resistentes a malatión en la mayoría de las poblaciones analizadas. En el caso del espinosad, observamos que la susceptibilidad a este insecticida de origen biológico fue elevada en la mayoría de las poblaciones, sin embargo, la población recogida en Xàbia (Alicante) mostró un nivel de susceptibilidad unas dos veces menor al resto de poblaciones. Mediante la selección en laboratorio, obtuvimos dos líneas resistentes a malatión, W-4Km y W-10Km, con unos niveles de resistencia con respeto a la línea susceptible C de 178 y 400 veces, respectivamente. Además, se seleccionó por primera vez en C. capitata una línea altamente resistente a espinosad (Xàbia-W-100s), que actualmente es unas 500 veces más resistente que la línea de laboratorio C. Con el objetivo de escoger la estrategia más adecuada para el manejo de la plaga, estudiamos la susceptibilidad a diferentes tipos de insecticidas en la línea resistente a malatión W- 4Km. En esta línea detectamos resistencia cruzada moderada a los organofosforados fentión, diazinón, fosmet, triclorfón y metil-clorpirifos (de 7 a 16 veces) y frente al carbamato carbaril, al piretroide lambda-cialotrina y al quimioesterilizante lufenurón (de 4 a 6 veces). Por otra parte, la resistencia cruzada frente a espinosad fue baja (1,5 veces). Es importante destacar que los niveles de resistencia estimados frente a todos los insecticidas fueron de uno o dos órdenes de magnitud inferiores al observado en la línea W-4Km frente a malatión (178 veces), hecho que podría deberse, al menos, a dos posibles hipótesis: que la mutación AChE G328A confiera mayor insensibilidad al malaoxón (forma activa del malatión) que a otros insecticidas que tienen como diana la AChE y/o, en segundo lugar, que el mecanismo de resistencia mediado por carboxilesterasas hidrolice el malatión de manera más eficiente que los otros insecticidas analizados. En el estudio de nuevos mecanismos de resistencia en C. capitata, por un lado, analizamos la diversidad de enzimas citocromo P450, asociadas con resistencia metabólica en otras especies, y por otro lado, desarrollamos un sistema para la detección de nuevas mutaciones puntuales que pudiesen aparecer en los genes que codifican la AChE (Ccace2) y la aliesterasa (Ccae7). Mediante el empleo de cebadores degenerados obtuvimos 37 genes CYP, que codifican enzimas P450, pertenecientes a cinco familias. Posteriormente, en un estudio de inducción con fenobarbital, observamos que la expresión de cuatro de los seis genes analizados era susceptible de ser inducida. Por otro lado, se puso a punto un sistema que permite amplificar y secuenciar, a partir de DNA genómico, los exones de los genes Ccace2 y Ccae7 en los que se han encontrado mutaciones relacionadas con resistencia a insecticidas en otras especies. Los resultados obtenidos facilitarán el estudio de nuevos mecanismos de resistencia mediados por estas enzimas en C. capitata. Se diseñó un método PCR-RFLP para identificar los individuos portadores de la mutación AChE G328A (alelo de resistencia Ccace2R) sin la necesidad de realizar bioensayos y que, además, permite detectar resistencia cuando ésta se encuentra a baja frecuencia. Según el análisis realizado, el alelo Ccace2R se observó en 25 de las 27 localidades españolas muestreadas en el territorio español, incluyendo las Islas Baleares y Canarias. Sin embargo, este alelo no se detectó en poblaciones procedentes de once países y de cinco continentes. El análisis de la presencia del alelo Ccace2R en las líneas resistentes a malatión durante el proceso de selección en el laboratorio mostró una rápida disminución de los homocigotos, tanto para el alelo susceptible como para el alelo de resistencia, en favor de los individuos heterocigotos. Así, después de 52 generaciones de selección, se observó que la totalidad de los individuos analizados de la línea W-10Km presentaban un genotipo heterocigoto para la mutación AChE G328A. Este desequilibrio contradice la segregación mendeliana esperada para un gen con dos alelos pero podría ser explicado por la existencia de una duplicación del gen Ccace2. La demostración de la presencia de esta duplicación se realizó mediante: i) el cruzamiento de individuos heterocigotos de la línea W-10Km con homocigotos susceptibles de la línea C, que dio lugar a una descendencia en la que el 100% de los individuos eran heterocigotos; ii) la evaluación del número de copias del gen Ccace2 por PCR cuantitativa en tiempo real (qPCR), que resultó dos veces mayor en individuos de la línea W-10Km en comparación con los de la línea C; iii) el análisis del nivel de expresión de Ccace2, que fue el doble en la línea W-10Km con respecto a la línea C, y iv) el estudio de la actividad AChE, que resultó mayor en los individuos de la línea W-10Km. Según los resultados obtenidos, una duplicación del gen Ccace2 provoca la coexistencia en un mismo cromosoma del alelo silvestre y del alelo mutado y, además, las dos copias del gen Ccace2, al estar ligadas, producen una heterocigosis permanente (Ccace2RS). De esta manera se explica que el hecho de que 100% de los individuos de la línea W-10Km mostrasen un perfil de restricción correspondiente a un individuo heterocigoto ya que, en realidad, eran homocigotos estructurales para la duplicación (genotipo CCace2RS/RS). Se ha detectado un coste biológico asociado a la duplicación que consiste en un incremento en la mortalidad acumulada de los adultos a partir del séptimo día después de la emergencia. La descripción de la duplicación Ccace2RS supone la identificación de un nuevo mecanismo de resistencia a malatión en C. capitata. Finalmente, mediante el diseño de un método de doble PCR-RFLP se determinó la presencia de la duplicación Ccace2RS en la mayoría de las poblaciones españolas. La proporción de individuos portadores de la duplicación osciló entre el 5% y el 35%, observándose los mayores valores de frecuencia en las poblaciones de C. capitata recogidas en la cuenca mediterránea. Podemos por lo tanto concluir que la resistencia a malatión asociada a la mutación AChE G328A y a la duplicación Ccace2RS está ampliamente establecida en las poblaciones españolas de C. capitata. Nuestros resultados desaconsejan la utilización del malatión (si fuera de nuevo autorizado) o de otros organofosforados para el control de esta plaga. Además, una de las líneas resistentes a malatión mostró resistencia cruzada frente a insecticidas con diferentes modos de acción y que se utilizan actualmente para el control de C. capitata, tales como lambda-cialotrina y lufenurón. La alta susceptibilidad a espinosad observada en las poblaciones españolas, así como la reducida resistencia cruzada estimada para este insecticida, sugieren que su utilización es adecuada para el control de la plaga. Sin embargo, la utilización de un sólo insecticida puede entrañar riesgos por favorecer la selección de resistencia, de hecho, mediante selección en laboratorio se obtuvo una población altamente resistente a espinosad. Por tanto, es recomendable implementar programas de control integrado y de manejo de la resistencia en C. capitata utilizando distintos sistemas de control e insecticidas con diferentes mecanismos de acción que permitan su sostenibilidad en el tiempo. Los sistemas de detección de alelos de resistencia desarrollados en este trabajo permitirán la detección precoz de resistencia en campo, facilitando la decisión sobre el sistema de control más adecuado. Además, los conocimientos generados podrán contribuir al desarrollo de nuevos sistemas de detección para otros mecanismos de resistencia. Abstract. The Mediterranean fruit fly, Ceratitis capitata (Wiedemann, 1824), is considered one of the most harmful pests in fruit crops. Until 2009, when malathion use was banned due to its not inclusion in the Annex I of Directive 91/414/EEC, the application of this organophosphate (OP) insecticide in Spain increased gradually due to the large economic losses caused by C. capitata. The increase in the frequency of treatments resulted in the development of resistant field populations. The study of a malathion-resistant population, collected in 2004 in Castelló (Comunidad Valenciana), allowed the identification of two resistance mechanisms: a single point mutation (G328A) in the target acetylcholinesterase (AChE), as well as a metabolic resistance mechanism, most likely carboxylesterase-mediated. Taking all the preceding into account, we studied the malathion resistance mechanisms in C. capitata. During the development of this PhD Thesis malathion use was banned by the European Union, being replaced by other insecticides, such as spinosad and lambda-cyhalotrin. Within this new working frame, the need to analyse the possible existence of cross-resistance to these insecticides and the susceptibility to spinosad in field populations was raised. This would define the baseline for future studies on resistance mechanisms. Firstly, through discriminant dose bioassays, we analysed malathion and spinosad susceptibility in twelve C. capitata populations from Andalucia, Aragon, Cataluña, C. Valenciana and the Baleares Islands. Our results suggest the presence of malathion-resistant individuals in most of the populations analysed. Regarding spinosad, we noticed a high susceptibility to this biologically derived insecticide in most of the populations, but in the one collected in Xabia (Alicante), which had a susceptibility level two times lower than the rest of populations. Through laboratory selection, we obtained two malathion-resistant strains, W-4Km and W-10Km, with resistance levels 178- and 400-fold, respectively, compared to the control susceptible C strain. Besides, a strain highly-resistant to spinosad (Xabia-W-100s), 500-times more resistant than control C strain, was selected. In order to decide the most appropriate management strategy for the pest, we studied the susceptibility to different insecticides in the malathion-resistant W-4Km strain. We detected a moderated cross-resistance to the OPs fenthion, diazinon, phosmet, trichlorphon and methylchlorpyrifos (7- to 16-fold), and to the carbamate carbaryl, the pyretroid lambda-cyhalotrin and the chemosterilizer lufenuron (4- to 6-fold). On the other hand, cross-resistance to spinosad was low (1.5-fold). It is important to note that resistance levels to all insecticides were one or two orders of magnitude less than that observed against malathion in W-4Km strain (178-fold), a fact that might be due to, at least, two possible causes: mutation AChE G328A may provide a higher insensitivity to malaoxon (the active form of malathion) than to other insecticides having AChE as target, and/or, secondly, the carboxylesterase-mediated resistance mechanism hydrolyzes malathion more efficiently than all other analysed insecticides. To investigate new resistance mechanisms in C. capitata we analysed the diversity of the cytochrome P450 enzymes, which have been associated to metabolic resistance in insects, and we developed a new method to detect single point mutations in acetylcholinesterase (Ccace2) and aliesterase (Ccae7) genes that could appear. Using degenerate primers we obtained 37 CYP genes, coding P450 enzymes, included in five families. Afterwards, in a phenobarbital-induction study, we observed that the expression of 4 out of the 6 analysed genes could be induced. On the other hand, a system was set up to amplify and to sequence from genomic DNA the exons of genes Ccace2 and Ccae7 where mutations related to insecticide resistance have been found in other species. The results obtained could facilitate the study of new resistance mechanisms in C. capitata mediated by these enzymes. A PCR-RFLP method was designed to detect the presence of the mutation AChE G328A (resistance allele Ccace2R), with no need to perform bioassays and allowing detecting resistance at low frequency. According to the analysis, the resistance allele was found in 25 out of 27 sampled locations in Spain, including the Balearic and the Canary Islands. However, this allele was not detected in other populations collected in 11 countries from 5 continents. The follow-up of the presence of the allele Ccace2R in the malathion-resistant strains during the selection process in the laboratory showed a quick decrease in homozygous individuals, for both the susceptible and the resistant alleles, favouring heterozygous. Thus, after 52 generations of selection, all the individuals analysed from W-10Km strain showed a heterozygous genotype for mutation AChE G328A, contradicting mendelian segregation as expected for a gene with two alleles. Afterwards, we were able to demonstrate that this was caused by the presence of a duplication of the gene coding acetylcholinesterase by: i) crossing heterozygous individuals from W-10Km strain with susceptible homozygous from C strain, originating a F1 population in which 100% of individuals were heterozygous; ii) evaluating the number of copies of gen Ccace2 by quantitative PCR in real time (qPCR), that happened to be twice higher in individuals from W-10Km VII strain when compared with C strain; iii) analysing the level of expression of Ccace2, twice in W- 10Km strain when compared to C strain; iv) studying the acetylcholinesterase activity, that was higher in individuals from W-10Km strain. According to these results, duplication of gen Ccace2 originates the coexistence of the susceptible and the resistant allele in the same chromosome. The two linked copies of the gene Ccace2 provoke the existence of permanent heterozygosis (Ccace2RS). This explains why the 100% of individuals from W-10Km strain showed an heterozygous restriction pattern since, in fact, they were structural homozygotes for the duplication (genotype Ccace2RS/RS). A biological cost has been detected associated to this duplication, consisting in a rise in accumulated adult mortality from the seventh day after emergence. The Ccace2RS duplication described in this study represents a new resistance mechanism to malathion in C. capitata. Finally, by the design of a double PCR-RFLP method, the presence of Ccace2RS duplication was confirmed in most of the Spanish populations. We observed that the proportion of individuals carrying the duplication oscillated between 5 and 35%, the frequency being higher in those C. capitata populations collected in the area of the Mediterranean basin. Therefore, we can conclude that malathion resistance associated to mutation AChE G328A and to Ccace2RS duplication are widely distributed in Spanish populations of C. capitata. Our results advice against the use of malathion (if it came to be newly authorized for use) or other OPs for the control of this pest. Besides, one of the malathion-resistant strains showed cross-resistance against insecticides with diverse action modes that are currently used for pest control, such as lambdacyhalotrin and lufenuron. High susceptibility to spinosad in the Spanish populations, as well as the reduced cross-resistance estimated for this insecticide suggests its adequacy for Medfly control. However, the use of a single insecticide is a risky strategy since it favours the selection of resistance. In fact, a population highly resistant to spinosad was obtained through laboratory selection. Therefore, it is advisable to implement integrated pest management (IPM) and resistance management programs for C. capitata control. Using insecticides with different modes of action and diverse control systems would contribute to the sustainability of the pest control. The resistance allele detection systems developed through this work will allow the early detection of resistance in the field, making possible the selection of the most appropriate method for pest control. Besides, the generated knowledge may also contribute to the development of new detection systems for other resistance mechanisms.

A platform for real-time control education with LEGO MINDSTORMS.

A set of software development tools for building real-time control systems on a simple robotics platform is described in the paper. The tools are being used in a real-time systems course as a basis for student projects. The development platform is a low-cost PC running GNU/Linux, and the target system is LEGO MINDSTORMS NXT, thus keeping the cost of the laboratory low. Real-time control software is developed using a mixed paradigm. Functional code for control algorithms is automatically generated in C from Simulink models. This code is then integrated into a concurrent, real-time software architecture based on a set of components written in Ada. This approach enables the students to take advantage of the high-level, model-oriented features that Simulink oers for designing control algorithms, and the comprehensive support for concurrency and real-time constructs provided by Ada.

ClimApp: A Novel Approach of an Intelligent HVAC Control System

This paper describes a novel deployment of an intelligent user-centered HVAC (Heating, Ventilating and Air Conditioner) control system. The main objective of this system is to optimize user comfort and to reduce energy consumption in office buildings. Existing commercial HVAC control systems work in a fixed and predetermined way. The novelty of the proposed system is that it adapts dynamically to the user and to the building environment. For this purpose the system architecture has been designed under the paradigm of Ambient Intelligence. A prototype of the system proposed has been tested in a real-world environment.

Experiences on the specification of algorithms for fire and smoke control in road tunnels

The main objective of ventilation systems in case of fire is the reduction of the possible consequences by achieving the best possible conditions for the evacuation of the users and the intervention of the emergency services. The required immediate transition, from normal to emergency functioning of the ventilation equipments, is being strengthened by the use of automatic and semi-automatic control systems, what reduces the response times through the help to the operators, and the use of pre-defined strategies. A further step consists on the use of closed-loop algorithms, which takes into account not only the initial conditions but their development (air velocity, traffic situation, etc.), optimizing smoke control capacity.

Knowledge-based models for adaptive traffic management systems

This paper describes a general approach for real time traffic management support using knowledge based models. Recognizing that human intervention is usually required to apply the current automatic traffic control systems, it is argued that there is a need for an additional intelligent layer to help operators to understand traffic problems and to make the best choice of strategic control actions that modify the assumption framework of the existing systems.

Integration of a data acquisition system based on FlexRIO technology with EPICS

EPICS (Experimental Physics and Industrial Control System) lies in a set of software tools and applications which provide a software infrastructure for building distributed data acquisition and control systems. Currently there is an increase in use of such systems in large Physics experiments like ITER, ESS, and FREIA. In these experiments, advanced data acquisition systems using FPGA-based technology like FlexRIO are more frequently been used. The particular case of ITER (International Thermonuclear Experimental Reactor), the instrumentation and control system is supported by CCS (CODAC Core System), based on RHEL (Red Hat Enterprise Linux) operating system, and by the plant design specifications in which every CCS element is defined either hardware, firmware or software. In this degree final project the methodology proposed in Implementation of Intelligent Data Acquisition Systems for Fusion Experiments using EPICS and FlexRIO Technology Sanz et al. [1] is used. The final objective is to provide a document describing the fulfilled process and the source code of the data acquisition system accomplished. The use of the proposed methodology leads to have two diferent stages. The first one consists of the hardware modelling with graphic design tools like LabVIEWFPGA which later will be implemented in the FlexRIO device. In the next stage the design cycle is completed creating an EPICS controller that manages the device using a generic device support layer named NDS (Nominal Device Support). This layer integrates the data acquisition system developed into CCS (Control, data access and communication Core System) as an EPICS interface to the system. The use of FlexRIO technology drives the use of LabVIEW and LabVIEW FPGA respectively. RESUMEN. EPICS (Experimental Physics and Industrial Control System) es un conjunto de herramientas software utilizadas para el desarrollo e implementación de sistemas de adquisición de datos y control distribuidos. Cada vez es más utilizado para entornos de experimentación física a gran escala como ITER, ESS y FREIA entre otros. En estos experimentos se están empezando a utilizar sistemas de adquisición de datos avanzados que usan tecnología basada en FPGA como FlexRIO. En el caso particular de ITER, el sistema de instrumentación y control adoptado se basa en el uso de la herramienta CCS (CODAC Core System) basado en el sistema operativo RHEL (Red Hat) y en las especificaciones del diseño del sistema de planta, en la cual define todos los elementos integrantes del CCS, tanto software como firmware y hardware. En este proyecto utiliza la metodología propuesta para la implementación de sistemas de adquisición de datos inteligente basada en EPICS y FlexRIO. Se desea generar una serie de ejemplos que cubran dicho ciclo de diseño completo y que serían propuestos como casos de uso de dichas tecnologías. Se proporcionará un documento en el que se describa el trabajo realizado así como el código fuente del sistema de adquisición. La metodología adoptada consta de dos etapas diferenciadas. En la primera de ellas se modela el hardware y se sintetiza en el dispositivo FlexRIO utilizando LabVIEW FPGA. Posteriormente se completa el ciclo de diseño creando un controlador EPICS que maneja cada dispositivo creado utilizando una capa software genérica de manejo de dispositivos que se denomina NDS (Nominal Device Support). Esta capa integra la solución en CCS realizando la interfaz con la capa EPICS del sistema. El uso de la tecnología FlexRIO conlleva el uso del lenguaje de programación y descripción hardware LabVIEW y LabVIEW FPGA respectivamente.

Hardware timestamping for image acquisition system based on FlexRIO and IEEE 1588 v2 Standard

Current fusion devices consist of multiple diagnostics and hundreds or even thousands of signals. This situation forces on multiple occasions to use distributed data acquisition systems as the best approach. In this type of distributed systems, one of the most important issues is the synchronization between signals, so that it is possible to have a temporal correlation as accurate as possible between the acquired samples of all channels. In last decades, many fusion devices use different types of video cameras to provide inside views of the vessel during operations and to monitor plasma behavior. The synchronization between each video frame and the rest of the different signals acquired from any other diagnostics is essential in order to know correctly the plasma evolution, since it is possible to analyze jointly all the information having accurate knowledge of their temporal correlation. The developed system described in this paper allows timestamping image frames in a real-time acquisition and processing system using 1588 clock distribution. The system has been implemented using FPGA based devices together with a 1588 synchronized timing card (see Fig.1). The solution is based on a previous system [1] that allows image acquisition and real-time image processing based on PXIe technology. This architecture is fully compatible with the ITER Fast Controllers [2] and offers integration with EPICS to control and monitor the entire system. However, this set-up is not able to timestamp the frames acquired since the frame grabber module does not present any type of timing input (IRIG-B, GPS, PTP). To solve this lack, an IEEE1588 PXI timing device its used to provide an accurate way to synchronize distributed data acquisition systems using the Precision Time Protocol (PTP) IEEE 1588 2008 standard. This local timing device can be connected to a master clock device for global synchronization. The timing device has a buffer timestamp for each PXI trigger line and requires tha- a software application assigns each frame the corresponding timestamp. The previous action is critical and cannot be achieved if the frame rate is high. To solve this problem, it has been designed a solution that distributes the clock from the IEEE 1588 timing card to all FlexRIO devices [3]. This solution uses two PXI trigger lines that provide the capacity to assign timestamps to every frame acquired and register events by hardware in a deterministic way. The system provides a solution for timestamping frames to synchronize them with the rest of the different signals.