Estudio de los materiales que componen el sistema constructivo de las viviendas del casco histórico de Maracaibo (Venezuela)

En este trabajo de investigación que se presenta para optar al grado de Doctor, se analizan y estudian los materiales que conforman las viviendas de mampostería de arenisca “Piedra de Ojo” del casco histórico de Maracaibo, Venezuela, construidas en el siglo XIX. No existe una bibliografía descriptiva técnico-constructiva del sistema constructivo, por lo que esta tesis complementa la escasa descripción estilística existente donde apenas se mencionan algunos materiales de construcción. Definido el marco histórico y las manzanas del área en donde se encontraban las viviendas preseleccionadas a estudiar, en la visita de campo se seleccionaron 12 que se encontraban en estado de deterioro, y que permitieron recolectar las muestras más fácilmente. Para realizar la caracterización y comportamientos de los diferentes materiales utilizados: piedra y morteros en los cerramientos, maderas en armaduras de tejados, techos y carpintería de puertas y ventanas, cerámicos en muros y acabados, etc. Para complementar lo antes dicho se ha dividido esta tesis en seis capítulos: En el capítulo I se desarrolla el estado del arte a nivel nacional e internacional de trabajos de investigación, similares. Se aborda la memoria histórica, que es una reseña de la evolución de la vivienda en la ciudad de Maracaibo. En el capítulo II se describe la metodología empleada en la tesis, de acuerdo a los objetivos, tanto generales como específicos de la investigación. Que ha cubierto diferentes frentes: consulta bibliográfica, levantamiento planimétrico, toma de muestras, análisis de visu, caracterización físico-química y correlación de resultados. Se ha desarrollado el trabajo tanto in situ como en laboratorio y despacho. El capítulo III presenta la caracterización de la arenisca “Piedra de Ojo”, se desarrolla: la descripción geológica y caracterización petrológica. Se reseñan los ensayos realizados en laboratorio como: caracterización de visu, caracterización petrográfica, estudio petrográfico por microcopia óptica de trasmisión, estudio petrográfico por microcopia electrónica de barrido, microscopia electrónica de barrido en modo electrones secundarios (SSE) y microscopia electrónica de barrido en modo electrones retrodispersados. También las propiedades escalares de los mampuestos y los siguientes valores: densidades, porosidades y resistencia mecánicas, entre otros. En el capítulo IV se analizan las características de los morteros aplicados en las viviendas, y la patología o lesiones que presentan. Se clasifican en tres tipos: mortero de junta o asiento, de enfoscado y revoco. Se documenta la realización de los ensayos físicos y químicos, resistencia mecánica y de granulometría; se explican sus componentes principales: conglomerante de cal, áridos y aditivos y la tecnología de fabricación, así como las características físicas, hídricas, químicas y granulométricas. El capítulo V, contiene las aplicaciones constructivas de los materiales de albañilería, Se describen otros elementos de la vivienda como; cimentaciones, muros mixtos, molduras, apliques y pinturas y finalmente pavimentos. Y en el capítulo VI se analizan las especies de madera más representativas usadas en las armaduras de las cubiertas, así como los elementos de cubrición. De igual forma se describe la carpintería de puertas y ventanas, así como sus dinteles o cargaderos de madera y se realiza la identificación anatómica, las propiedades físicas y mecánicas de las utilizadas. Entre los resultados y conclusiones se determinó que el 90% de los materiales utilizados en su construcción proceden de zonas cercanas a la construcción de la vivienda, como la formación El Milagro convertida en cantera de piedra y que el resto de los materiales provenían de la Isla de Toas y de la exportación de las islas del Caribe y de Europa como el cemento. El principal aporte de esta investigación es el análisis técnico constructivo y la caracterización física, mecánica y química de los materiales de la vivienda, con el fin de que dicha información sea usada para definir los materiales nuevos a utilizar en las restauraciones de las viviendas y en futuras líneas de investigación. ABSTRACT In this research paper submitted to opt to the degree of Doctor, the materials that make the “Piedra de Ojo” sandstone masonry houses of the historical center of Maracaibo, Venezuela, built in the XIX century, are analyzed and studied. There exists no technical-constructive descriptive literature of the constructive system, so this thesis complements the very limited existing stylistic description, where barely some construction materials are mentioned. With the historical context and the blocks of the area where the preselected houses to be studied being defined, 12 of these houses that were in a state of decay (deterioration) were selected and this condition allowed to collect samples more easily, in order to carry out the characterization and behavior of the different materials used: stone and mortars in the walls, wood trusses in roofs, ceilings and woodwork of doors and windows, walls and ceramic finishes, etc. To complement the foregoing, this thesis has been divided in six chapters: In Chapter I, the state of art at national and international levels of similar research is developed, which is a review of the evolution of housing in the city of Maracaibo. In Chapter II, the methodology used in the thesis is described, according to the research’s objectives, general and specific ones, which have covered several fronts: literature survey, planimetric survey, sampling, visu analysis, physical-chemical characterization and correlation of results. Chapter III presents the characterization of the “Piedra de Ojo” sandstone; geological description and petrologic characterization are developed. Essays performed in the laboratory are reviewed, such as: visu characterization, petrographic characaterization, petrographic study by optical microscopy of transmission, petrographic study by electronic scanning microscopy in secondary electron mode (SSE) and electron microscopy scaning by backscattered electron mode. Also scalar properties of the masonry and the following: density, porosity and mechanical resistance, among others. In Chapter IV, characteristics of the mortars used in the houses are analyzed and pathology or damages are presented. They are classified into three types: grout, cement render and plaster. Physical and chemical testing, mechanical strength and grain size (granulometric) is documented; its main components are explained: lime binder, aggregates and additives and manufacturing technology as well as the physical, water, chemical and granulometric characteristics. Chapter V contains the constructive applications of masonry materials. Other housing elements are described, such as; foundations, mixed walls, moldings, wall paintings and finally floorings (pavements). And in chapter VI the most representative species of wood used in the overhead fixtures and cover elements are analyzed. Likewise, woodwork of doors and windows and their wooden lintels or landings are described; anatomical identification and physical and mechanical properties of the ones used is made. The results and conclusions determined that 90% of the materials used in its construction came from areas near the construction of housing, such as El Milagro formation, converted into stone quarry and other materials came from the Toas Island and from the export of the Caribbean islands and Europe, such as cement. The main contribution of this research is the constructive technical analysis and physical, mechanical and chemical characterization of the materials of the houses, in order that such information is used to define the new materials to be used in the housing restoration and future research lines.

Effect of nano-Si2O and nano-Al2O3 on cement mortars for use in agriculture and livestock production

The effect of nano-silica, nano-alumina and binary combinations on surface hardness, resistance to abrasion and freeze-thaw cycle resistance in cement mortars was investigated. The Vickers hardness, the Los Angeles coefficient (LA) and the loss of mass in each of the freeze–thaw cycles to which the samples were subjected were measured. Four cement mortars CEM I 52.5R were prepared, one as control, and the other three with the additions: 5% nano-Si, 5% nano-Al and mix 2.5% n-Si and 2.5% n-Al. Mortars were tested at 7, 28 and 90 d of curing to determine compression strength, total porosity and pore distribution by mercury intrusion porosimetry (MIP) and the relationship between the CSH gel and Portlandite total by thermal gravimetric analysis (TGA). The capillary suction coefficient and an analysis by a scanning electron microscope (SEM) was made. There was a large increase in Vickers surface hardness for 5% n-Si mortar and a slight increase in resistance to abrasion. No significant difference was found between the mortars with nano-particles, whose LA was about 10.8, classifying them as materials with good resistance to abrasion. The microstructure shows that the addition of n-Si in mortars refines their porous matrix, increases the amount of hydrated gels and generates significant changes in both Portlandite and Ettringite. This produced a significant improvement in freeze–thaw cycle resistance. The effect of n-Al on mortar was null or negative with respect to freeze–thaw cycle resistance.

Effect of carbon fibres on the mechanical properties and corrosion levels of reinforced portland cement mortars

The changes in mechanical properties of portland cement mortars due to the addition of carbon fibres (CF) to the mix have been studied. Compression and flexural strengths have been determined in relation to the amount of fibres added to the mix, water/binder ratio, curing time and porosity. Additionally, the corrosion level of reinforcing steel bars embedded in portland cement mortars containing CF and silica fume (SF) have also been investigated and reinforcing steel corrosion rates have been determined. As a consequence of the large concentration of oxygen groups in CF surface, a good interaction between the CF and the water of the mortar paste is to be expected. A CF content of 0.5% of cement weight implies an optimum increase in flexural strength and an increase in embedded steel corrosion.

Radiological impact of cement, concrete and admixtures in Spain

It has been analyzed samples of portland cement (PC) with and without admixtures, samples of calcium aluminate cement (CAC) with different content of Al2O3 and specimens of concrete made with PC and CAC using High Resolution Gamma Spectrometry. The activity concentration index (I) is much less than 0.5 mSv y-1 for all the concrete specimens according to the Radiation protection document 112 of the European Commission. The PC without admixtures (CEM I 52,5 R) and the PC with addition of limestone (CEM II/BL 32,5 N) also have an I value much lower than 0.5 and the PC with the addition of fly ash and blast furnace slag (CEM IV/B (V) 32,5 N and III/A 42.5 N/SR) have an I value close to 0.6. The I value of the CAC used in the manufacture of structural precast concrete is of the order of 1 mSv y-1. Some of the CAC used in refractory concrete reaches a value close to 2 mSv y-1.

Multifunctional cement composites strain and damage sensors applied on reinforced concrete (RC) structural elements

In this research, strain-sensing and damage-sensing functional properties of cement composites have been studied on a conventional reinforced concrete (RC) beam. Carbon nanofiber (CNFCC) and fiber (CFCC) cement composites were used as sensors on a 4 m long RC beam. Different casting conditions (in situ or attached), service location (under tension or compression) and electrical contacts (embedded or superficial) were compared. Both CNFCC and CFCC were suitable as strain sensors in reversible (elastic) sensing condition testing. CNFCC showed higher sensitivities (gage factor up to 191.8), while CFCC only reached gage factors values of 178.9 (tension) or 49.5 (compression). Furthermore, damage-sensing tests were run, increasing the applied load progressively up to the RC beam failure. In these conditions, CNFCC sensors were also strain sensitive, but no damage sensing mechanism was detected for the strain levels achieved during the tests. Hence, these cement composites could act as strain sensors, even for severe damaged structures near to their collapse.

Strain and damage sensing properties on multifunctional cement composites with CNF admixture

Both strain and damage sensing properties on carbon nanofiber cement composites (CNFCC) are reported in the present paper. Strain sensing tests were first made on the material’s elastic range. The applied loading levels have been previously calculated from mechanical strength tests. The effect of several variables on the strain-sensing function was studied, e.g. cement pastes curing age, current density, loading rate or maximum stress applied. All these parameters were discussed using the gage factor as reference. After this first set of elastic experiments, the same specimens were gradually loaded until material’s failure. At the same time both strain and resistivity were measured. The former was controlled using strain gages, and the latter using a multimeter on a four probe setup. The aim of these tests was to prove the sensitivity of these CNF composites to sense their own damage, i.e. check the possibility of fabricating structural damage sensors with CNFCC’s. All samples with different CNF dosages showed good strain-sensing capacities for curing periods of 28 days. Furthermore, a 2%CNF reinforced cement paste has been sensitive to its own structural damage.

Mechanical Properties and Durability of CNT Cement Composites

In the present paper, changes in mechanical properties of Portland cement-based mortars due to the addition of carbon nanotubes (CNT) and corrosion of embedded steel rebars in CNT cement pastes are reported. Bending strength, compression strength, porosity and density of mortars were determined and related to the CNT dosages. CNT cement paste specimens were exposed to carbonation and chloride attacks, and results on steel corrosion rate tests were related to CNT dosages. The increase in CNT content implies no significant variations of mechanical properties but higher steel corrosion intensities were observed.

Self-heating function of carbon nanofiber cement pastes

The viability of carbon nanofiber (CNF) composites in cement matrices as a self-heating material is reported in this paper. This functional application would allow the use of CNF cement composites as a heating element in buildings, or for deicing pavements of civil engineering transport infrastructures, such as highways or airport runways. Cement pastes with the addition of different CNF dosages (from 0 to 5% by cement mass) have been prepared. Afterwards, tests were run at different fixed voltages (50, 100 and 150V), and the temperature of the specimens was registered. Also the possibility of using a casting method like shotcrete, instead of just pouring the fresh mix into the mild (with no system’s efficiency loss expected) was studied. Temperatures up to 138 °C were registered during shotcrete-5% CNF cement paste tests (showing initial 10 °C/min heating rates). However a minimum voltage was required in order to achieve a proper system functioning.

Effect of aspect ratio on strain sensing capacity of carbon fiber reinforced cement composites

The electrical resistivity of carbon fiber reinforced cement composites (CFRCCs) has been widely studied, because of their utility as multifunctional materials. The percolation phenomenon has also been reported and modeled when the electrical behavior of those materials had to be characterized. Amongst the multiple applications of multifunctional cement composites the ability of a CFRCC to act as a strain sensor is attractive. This paper provides experimental data relating self-sensing function and percolation threshold, and studying the effect of fiber aspect ratio on both phenomena. Higher fiber slenderness permitted percolation at lower carbon fiber addition, affected mechanical properties and improved strain-sensing sensitivity of CFRCC, which was also improved if percolation had not been achieved.

Influence of using slag cement on the microstructure and durability related properties of cement grouts for micropiles

Today, the use of micropiles for different applications has become very common. In Spain, the cement grouts for micropiles are prepared using ordinary Portland cement and w:c ratio 0.5, although the micropiles standards do not restrict the cement type to use, provided that it reaches a certain compressive strength. In this study, the influence of using slag cement on the microstructure and durability related properties of cement grouts for micropiles have been studied until 90 hardening days, compared to an ordinary Portland cement. Finally, slag cement grouts showed good service properties, better than ordinary Portland cement ones.

Blending of industrial waste from different sources as partial substitution of Portland cement in pastes and mortars

Binary and ternary combinations of sewage sludge ash (SSA) with marble dust (MD), fly ash (FA) and rice husk ash (RHA) as replacement in Portland cement pastes, were assessed. Several tests were carried out at different curing ages: thermogravimetry, density, water absorption, ultrasonic pulse velocity and mechanical strengths. Pozzolanic effects of the mineral admixtures, densities similar to control sample and improved absorptions when combining waste materials were identified. In general, the compressive strength reaches or exceeds the cement strength class, and blending SSA, FA and RHA (30% cement replacement) increase of strength by 9%, compared to the control sample, was achieved.

Efficiency of a conductive cement-based anodic system for the application of cathodic protection, cathodic prevention and electrochemical chloride extraction to control corrosion in reinforced concrete structures

This article describes the research carried out regarding the application of cathodic protection (CP) and cathodic prevention (CPrev), in some cases with a pre-treatment of electrochemical chloride extraction (ECE), on representative specimens of reinforced concrete structures, using an anodic system consisting of a graphite-cement paste applied as a coating on the surface. The aim of this research is to find out the competence of this anode for the aforementioned electrochemical treatments. The efficiency of this anode has been clearly demonstrated, as well as its capability to apply a combined process of ECE and after CP.

Shape Effect of Electrochemical Chloride Extraction in Structural Reinforced Concrete Elements Using a New Cement-Based Anodic System

This article shows the research carried out by the authors focused on how the shape of structural reinforced concrete elements treated with electrochemical chloride extraction can affect the efficiency of this process. Assuming the current use of different anode systems, the present study considers the comparison of results between conventional anodes based on Ti-RuO2 wire mesh and a cement-based anodic system such as a paste of graphite-cement. Reinforced concrete elements of a meter length were molded to serve as laboratory specimens, to closely represent authentic structural supports, with circular and rectangular sections. Results confirm almost equal performances for both types of anode systems when electrochemical chloride extraction is applied to isotropic structural elements. In the case of anisotropic ones, such as rectangular sections with no uniformly distributed rebar, differences in electrical flow density were detected during the treatment. Those differences were more extreme for Ti-RuO2 mesh anode system. This particular shape effect is evidenced by obtaining the efficiencies of electrochemical chloride extraction in different points of specimens.

Emissions of polybrominated dibenzo-p-dioxins and dibenzofurans (PBDD/Fs) and polycyclic aromatic hydrocarbons (PAHs) from a cement kiln using a continuous monitoring system

Resumen de la comunicación presentada en PIC2015 – the 14th International Congress on Combustion By-Products and Their Health Effects, Umeå, Sweden, 14-17 June 2015.

Impedance spectroscopy study of the effect of environmental conditions in the microstructure development of OPC and slag cement mortars

In this work, the microstructure of mortars made with an ordinary Portland cement and slag cement has been studied. These mortars were exposed to four different constant temperature and relative humidity environments during a 180-day period. The microstructure has been studied using impedance spectroscopy, and mercury intrusion porosimetry as a contrast technique. The impedance spectroscopy parameters make it possible to analyze the evolution of the solid fraction formation for the studied mortars and their results are confirmed with those obtained using mercury intrusion porosimetry. The development of the pore network of mortars is affected by the environment. However, slag cement mortars are more influenced by temperature while the relative humidity has a greater influence on the OPC mortars. The results show that slag cement mortars hardened under non-optimal environments have a more refined microstructure than OPC mortars for the studied environmental conditions.