Estudo da influência da temperatura de brasagem nas uniões zircônia/aço inox 304 utilizando metalização mecânica

Metal-Ceramic (M/C) Zirconia-stainless steel interfaces have been processed through brazing techniques due to the excellent combination of properties such as high temperature stability, high corrosion resistance and good mechanical properties. However, some M/C interfaces show some defects, like porosity and cracks results in the degradation of the interfaces, leading even to its total rupture. Most of time, those defects are associated with an improper brazing parameters selection to the M/C system. In this work, ZrO2 Y-TZP and ZrO2 Mg - PSZ were joint with the stainless steel grade 304 by brazing using a eutectic silver-copper (Ag28Cu) interlayer alloy with different thermal cycles. Ceramic surfaces were previous mechanically metallized with titanium to improve adhesion of the system. The effect of temperature on the M/C interface was studied. SEM-EDS and 3 point flexural bend test were performed to evaluate morphology, chemical composition and mechanical resistance of the M/C interfaces. Lower thermal cycle temperatures produced better results of mechanical resistance, and more regular/ homogeneous reaction layers between braze alloy and metal-ceramic surfaces. Also was proved the AgCu braze alloy activation in situ by titanium

Propiedades dieléctricas y térmicas de cristales líquidos: dímeros y bent-core

194 p.

Optical Waveguides and Structures for Short Haul Optical Communication Channels within Printed Circuit Boards

Optical waveguides have shown promising results for use within printed circuit boards. These optical waveguides have higher bandwidth than traditional copper transmission systems and are immune to electromagnetic interference. Design parameters for these optical waveguides are needed to ensure an optimal link budget. Modeling and simulation methods are used to determine the optimal design parameters needed in designing the waveguides. As a result, optical structures necessary for incorporating optical waveguides into printed circuit boards are designed and optimized. Embedded siloxane polymer waveguides are investigated for their use in optical printed circuit boards. This material was chosen because it has low absorption, high temperature stability, and can be deposited using common processing techniques. Two sizes of waveguides are investigated, 50 $unit{mu m}$ multimode and 4 - 9 $unit{mu m}$ single mode waveguides. A beam propagation method is developed for simulating the multimode and single mode waveguide parameters. The attenuation of simulated multimode waveguides are able to match the attenuation of fabricated waveguides with a root mean square error of 0.192 dB. Using the same process as the multimode waveguides, parameters needed to ensure a low link loss are found for single mode waveguides including maximum size, minimum cladding thickness, minimum waveguide separation, and minimum bend radius. To couple light out-of-plane to a transmitter or receiver, a structure such as a vertical interconnect assembly (VIA) is required. For multimode waveguides the optimal placement of a total internal reflection mirror can be found without prior knowledge of the waveguide length. The optimal placement is found to be either 60 µm or 150 µm away from the end of the waveguide depending on which metric a designer wants to optimize the average output power, the output power variance, or the maximum possible power loss. For single mode waveguides a volume grating coupler is designed to couple light from a silicon waveguide to a polymer single mode waveguide. A focusing grating coupler is compared to a perpendicular grating coupler that is focused by a micro-molded lens. The focusing grating coupler had an optical loss of over -14 dB, while the grating coupler with a lens had an optical loss of -6.26 dB.

Species and size selectivity in a 'red' sea bream longline 'metier' in the Algarve (southern Portugal)

A longline 'metier' using small hooks for 'red' sea breams (Pagellus acarne and Pagellus erythrinus) in the Algarve (south of Portugal) was studied. Experimental longlining was carried out with three sizes of "Mustad" round bend, flatted, spade end Quality 2316 DT hooks (numbers 11, 13 and 15) and two types of bait: razor shell (Ensis siliqua) and mud shrimp (Upogebia pusilla). A total of 3 328 fish and at least 36 species were caught with 33 600 hooks fished in 28 longline sets. Five species of sea breams (Sparidae) accounted for 79% of the catch: Pagellus acarne, Pagellus erythrinus, Diplodus vulgaris, Spondyliosoma cantharus, and Boops boops. High catch rates of 20-30 fish per 100 hooks were made in a number of 1 200 hook longline sets, with total catch weights of 40 to more than 60 kg per set. In general, the smallest hook (number 15) had the highest catch rate. Bait type did not significantly affect the catch size distributions. Although more fish were caught with the razor shell bait, higher catch rates of 'red' sea breams were obtained with mud shrimp. Catch rates were also affected by the location of the fishing grounds and the time of the set, with the highest catch rates obtained when the longline was set within two hours before sunrise. A wide size range was caught for each species, with highly overlapped catch size frequency distributions for the three hook sizes used. Except for Spondyliosoma cantharus, few illegal-sized fish were caught, even with the smallest hook. The logistic model fitted by maximum likelihood was used to describe hook selectivity for Diplodus vulgaris, Pagellus acarne, Pagellus erythrinus, and Spondyliosoma cantharus. (C) Ifremer-Elsevier, Paris.