Considerations in light truck suspension design

The present work aims at to approach considerations of trucks suspension design. The proposal of the work consists of discussing the aspects related to the acting of the suspension and of factors that interact with the system through representative models of the dynamic behaviour of the vehicle ride when operating in total load and/or empty conditions. The importance of this work is to revise some procedures of suspension study in the sense of adapting them to the Brazilian reality, tends in view the importance of the design characterisation and adaptation to the typical roads of Brazil. Copyright © 2000 Society of Automotive Engineers, Inc.

Curauá fibers in the automobile industry - a sustainability assessment

Replacing glass fibers with natural fibers in the automobile industry can yield economic, environmental and social benefits. This article evaluates the prospective environmental impacts of automobile applications of curauá fiber (Ananas erectifolius), which nearly equates the physical properties of glass fibers. The study identified economic and social advantages of applying curauá fiber composites in car parts. Besides costing 50% less than fiber glass, the use of curauá fibers can promote regional development in the Amazon region. In order to realize significant environmental benefits, however, the curauá-based composites would have to be lighter than their glass fiber-based counterparts. © 2006 Elsevier Ltd. All rights reserved.

Improvement and evaluation of the MS2SV for mixed systems design described in abstraction high level

This paper presents an important improvement of the MS2SV tool. The MS2SV performs the translation of mixed systems developed in MATLAB / Simulink for a structural or behavioral description in VHDL-AMS. Previously, the MS2SV translated only models of the LIB MS2SV library. This improvement allows designer to create your own library to translation. As case study was used a rudder controller employed in an unmanned aerial vehicle. For comparison with the original model the VHDL-AMS code obtained by the translation was simulated in SystemVision environment. The results proved the efficiency of the tool using the translation improvement proposed in this paper.

Design of a labVIEW system applied to predictive maintenance

The implementation of vibration analysis techniques based on virtual instrumentation has spread increasingly in the academic and industrial branch, since the use of any software for this type of analysis brings good results at low cost. Among the existing software for programming and creation of virtual instruments, the LabVIEW was chosen for this project. This software has good interface with the method of graphical programming. In this project, it was developed a system of rotating machine condition monitoring. This monitoring system is applied in a test stand, simulating large scale applications, such as in hydroelectric, nuclear and oil exploration companies. It was initially used a test stand, where an instrumentation for data acquisition was inserted, composed of accelerometers and inductive proximity sensors. The data collection system was structured on the basis of an NI 6008 A/D converter of National Instruments. An electronic circuit command was developed through the A/D converter for a remote firing of the test stand. The equipment monitoring is performed through the data collected from the sensors. The vibration signals collected by accelerometers are processed in the time domain and frequency. Also, proximity probes were used for the axis orbit evaluation and an inductive sensor for the rotation and trigger measurement. © (2013) Trans Tech Publications, Switzerland.

O designer e a prática profissional na indústria automobilística no Brasil

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Capas de Vicente Di Grado na década de 1960: análises e leituras

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Capas de Vicente Di Grado na década de 1960

O resgate da história e da memória do design gráfico brasileiro ainda possui algumas lacunas, pois muitos profissionais, seus projetos e obras não são lembrados ou ainda não foram estudados e registrados, deixando uma lacuna na história gráfico-visual de nosso país. Este artigo pretende contribuir nesse sentido, resgatando as capas de livros projetadas por Vicente Di Grado. Designer gráfico, artista plástico e docente, Di Grado (1922-2005) atuou como principal capista para a Editora Clube do Livro entre as décadas de 1950 e 1970, sendo seu maior período de produção a década de 1960, justamente o objeto deste estudo. Pelo conjunto de seu trabalho, recebeu o Prêmio Jabuti em 1963. Sua obra representa uma grande fonte de elementos e referências gráficas, além de ter marcado a linguagem editorial da Editora Clube do Livro.

A SIMPLIFIED MODEL FOR EVALUATING TIRE WEAR DURING CONCEPTUAL DESIGN

In the field of vehicle dynamics, commercial software can aid the designer during the conceptual and detailed design phases. Simulations using these tools can quickly provide specific design metrics, such as yaw and lateral velocity, for standard maneuvers. However, it remains challenging to correlate these metrics with empirical quantities that depend on many external parameters and design specifications. This scenario is the case with tire wear, which depends on the frictional work developed by the tire-road contact. In this study, an approach is proposed to estimate the tire-road friction during steady-state longitudinal and cornering maneuvers. Using this approach, a qualitative formula for tire wear evaluation is developed, and conceptual design analyses of cornering maneuvers are performed using simplified vehicle models. The influence of some design parameters such as cornering stiffness, the distance between the axles, and the steer angle ratio between the steering axles for vehicles with two steering axles is evaluated. The proposed methodology allows the designer to predict tire wear using simplified vehicle models during the conceptual design phase.

le mostre di moda

le genealogie di judith clark e l'algebra di anna piaggi

Design and control techniques of optical networks

The world of communication has changed quickly in the last decade resulting in the the rapid increase in the pace of peoples’ lives. This is due to the explosion of mobile communication and the internet which has now reached all levels of society. With such pressure for access to communication there is increased demand for bandwidth. Photonic technology is the right solution for high speed networks that have to supply wide bandwidth to new communication service providers. In particular this Ph.D. dissertation deals with DWDM optical packet-switched networks. The issue introduces a huge quantity of problems from physical layer up to transport layer. Here this subject is tackled from the network level perspective. The long term solution represented by optical packet switching has been fully explored in this years together with the Network Research Group at the department of Electronics, Computer Science and System of the University of Bologna. Some national as well as international projects supported this research like the Network of Excellence (NoE) e-Photon/ONe, funded by the European Commission in the Sixth Framework Programme and INTREPIDO project (End-to-end Traffic Engineering and Protection for IP over DWDM Optical Networks) funded by the Italian Ministry of Education, University and Scientific Research. Optical packet switching for DWDM networks is studied at single node level as well as at network level. In particular the techniques discussed are thought to be implemented for a long-haul transport network that connects local and metropolitan networks around the world. The main issues faced are contention resolution in a asynchronous variable packet length environment, adaptive routing, wavelength conversion and node architecture. Characteristics that a network must assure as quality of service and resilience are also explored at both node and network level. Results are mainly evaluated via simulation and through analysis.

Reduced-order modelling, circuit-level design and SOI fabrication of microelectromechanical resonators

This thesis deals with two important research aspects concerning radio frequency (RF) microresonators and switches. First, a new approach for compact modeling and simulation of these devices is presented. Then, a combined process flow for their simultaneous fabrication on a SOI substrate is proposed. Compact models for microresonators and switches are extracted by applying mathematical model order reduction (MOR) to the devices finite element (FE) description in ANSYS c° . The behaviour of these devices includes forms of nonlinearities. However, an approximation in the creation of the FE model is introduced, which enables the use of linear model order reduction. Microresonators are modeled with the introduction of transducer elements, which allow for direct coupling of the electrical and mechanical domain. The coupled system element matrices are linearized around an operating point and reduced. The resulting macromodel is valid for small signal analysis around the bias point, such as harmonic pre-stressed analysis. This is extremely useful for characterizing the frequency response of resonators. Compact modelling of switches preserves the nonlinearity of the device behaviour. Nonlinear reduced order models are obtained by reducing the number of nonlinearities in the system and handling them as input to the system. In this way, the system can be reduced using linear MOR techniques and nonlinearities are introduced directly in the reduced order model. The reduction of the number of system nonlinearities implies the approximation of all distributed forces in the model with lumped forces. Both for microresonators and switches, a procedure for matrices extraction has been developed so that reduced order models include the effects of electrical and mechanical pre-stress. The extraction process is fast and can be done automatically from ANSYS binary files. The method has been applied for the simulation of several devices both at devices and circuit level. Simulation results have been compared with full model simulations, and, when available, experimental data. Reduced order models have proven to conserve the accuracy of finite element method and to give a good description of the overall device behaviour, despite the introduced approximations. In addition, simulation is very fast, both at device and circuit level. A combined process-flow for the integrated fabrication of microresonators and switches has been defined. For this purpose, two processes that are optimized for the independent fabrication of these devices are merged. The major advantage of this process is the possibility to create on-chip circuit blocks that include both microresonators and switches. An application is, for example, aswitched filter bank for wireless transceiver. The process for microresonators fabrication is characterized by the use of silicon on insulator (SOI) wafers and on a deep reactive ion etching (DRIE) step for the creation of the vibrating structures in single-crystal silicon and the use of a sacrificial oxide layer for the definition of resonator to electrode distance. The fabrication of switches is characterized by the use of two different conductive layers for the definition of the actuation electrodes and by the use of a photoresist as a sacrificial layer for the creation of the suspended structure. Both processes have a gold electroplating step, for the creation of the resonators electrodes, transmission lines and suspended structures. The combined process flow is designed such that it conserves the basic properties of the original processes. Neither the performance of the resonators nor the performance of the switches results affected by the simultaneous fabrication. Moreover, common fabrication steps are shared, which allows for cheaper and faster fabrication.

Compatibilità aeronautica. Definizione dei vincoli fisici per le aree limitrofe all'Aeroporto "G. Marconi" di Bologna

Per garantire la sicurezza di tutte le operazioni in volo (avvicinamento, decollo, holding, ecc..) il decreto legge del 15 marzo del 2006 n. 151 ha imposto la redazione di opportune cartografie basate sul Regolamento ENAC per la Costruzione e l’Esercizio degli Aeroporti e sulla normativa internazionale ICAO così da poterle annettere agli Strumenti Urbanistici del territorio e governare lo sviluppo delle costruzioni. La sicurezza delle operazioni in volo è garantita attraverso delle Superfici di Delimitazione Ostacoli che impongono dei vincoli plano-altimetrici nelle aree limitrofe agli Aeroporti, quindi costruzioni, alberi e lo stesso terreno non devono forare queste superfici altrimenti diventerebbero “Ostacoli” alla navigazione aerea. Per gli ostacoli già presenti sono definiti dei provvedimenti da adottarsi in funzione della superficie che questi forano: potranno essere abbattuti se ricadenti in aree critiche come in prossimità delle piste oppure essere segnalati in mappe in uso ai piloti e anche con segnali visivi posizionati sugli stessi. Per quanto riguarda le future costruzioni, queste non potranno mai diventare Ostacolo in quanto sarà obbligatorio rispettare i vincoli plano-altimetrici. La tesi di laurea in questione vuole illustrare come si è arrivati alla redazione delle sopraccitate mappe nel caso specifico dell'Aeroporto Guglielmo Marconi di Bologna; sono analizzate nel primo capitolo le caratteristiche fisiche degli Aeroporti per acquisire una certa padronanza su termini tecnici che compaiono nei capitoli successivi (è inoltre presente un glossario). Nel secondo capitolo è individuato il percorso normativo che ha portato alla redazione dell’ultima revisione al Codice della Navigazione. Il capitolo 3 introduce le superfici di delimitazione ostacoli secondo quanto esposto nel Regolamento per la Costruzione e l’Esercizio degli Aeroporti di ENAC; il capitolo 4 è dedicato al lay-out dell’Aeroporto Guglielmo Marconi di Bologna. Infine la tesi si conclude con il capitoli 5 nel quale sono esposte le fasi e le metodologie usate per la realizzazione delle planimetrie e con il capitolo 6 in cui si discute delle problematiche sorte a causa dell’orografia del territorio che deve tenersi nella giusta considerazione per la definizione dei suddetti vincoli aeronautici.