Avaliação da camada intermetálica em placas de circuito impresso com acabamento superficial HASL com diferentes processos de soldagem

Dissertação de mestrado integrado em Engenharia de Materiais

Numerical simulation of the reflow soldering process

Dissertação de mestrado integrado em Mechanical Engineering

Estudo do comportamento tribológico de materiais compósitos à base de titânio reforçado com partículas cerâmicas para aplicação em implantes articulares

Dissertação de mestrado integrado em Engenharia Biomédica

Elaboration et caractérisation des nanocristaux de Zn F O enfouis 1-x x dans des diélectriques pour des applications en spin-électronique

Tese de Doutoramento em Ciências - Especialidade em Física

High performance screen printable lithium-ion battery cathode ink based on C-LiFePO4

Lithium-ion battery cathodes have been fabricated by screen-printing through the development of CLiFePO4 inks. It is shown that shear thinning polymer solutions in N-methyl-2-pyrrolidone (NMP) with Newtonian viscosity above 0.4 Pa s are the best binders for formulating a cathode paste with satisfactory film forming properties. The paste shows an elasticity of the order of 500 Pa and, after shear yielding, shows an apparent viscosity of the order of 3 Pa s for shear rates corresponding to those used during screen-printing. The screen-printed cathode produced with a thickness of 26 mm shows a homogeneous distribution of the active material, conductive additive and polymer binder. The total resistance and diffusion coefficient of the cathode are 450 V and 2.5 10 16cm2 s 1, respectively. The developed cathodes show an initial discharge capacity of 48.2 mAh g 1 at 5C and a discharge value of 39.8 mAh g 1 after 50 cycles. The capacity retention of 83% represents 23% of the theoretical value (charge and/or discharge process in twenty minutes), demonstrating the good performance of the battery. Thus, the developed C-LiFePO4 based inks allow to fabricate screen-printed cathodes suitable for printed lithium-ion batteries

Development of sensing systems for environmental monitoring

This project focused on the investigation and the development of a chemical sensing system for the determination of chromium Cr6+ and a bio-reactor followed by electrochemical detection at a glassy carbon electrode, for the determination of organochlorine compounds. The conjugation of Cr6+ with 1,5-diphenylcarbazide was studied at various types of electrodes such as glassy carbon, ultra-trace epoxy-graphite, chemically or un-modified carbon-paste and dropping-mercury. The cyclic voltammetric behaviour of the complex was also investigated. In addition, the possibility of developing a chemical sensor, Le. an electrochemical probe capable of sensing Cr6+ through its complexation with 1,5-diphenylacarbazide was studied. The conjugations of l-chloro-2,4-dinitrobenzene, 2,4-dichloronitrobenzene and ethacrynic, which are electrophilic organochlorine compounds, with reduced glutathione, were studied in order to test the bioreactor developed, based on the immobilisation of glutathione s-transferase. This was carried out at different types of electrodes such as glassy-carbon, gold, silver, platinum, epoxy-graphite, hangingmercury, and ferrocene-modified rotating-disc electrodes.

Optimisation of a surface mount technology process using a SnAgCu lead-free alloy

The impending introduction of lead-free solder in the manufacture of electrical and electronic products has presented the electronics industry with many challenges. European manufacturers must transfer from a tin-lead process to a lead-free process by July 2006 as a result of the publication of two directives from the European Parliament. Tin-lead solders have been used for mechanical and electrical connections on printed circuit boards for over fifty years and considerable process knowledge has been accumulated. Extensive literature reviews were conducted on the topic and as a result it was found there are many implications to be considered with the introduction of lead-free solder. One particular question that requires answering is; can lead-free solder be used in existing manufacturing processes? The purpose of this research is to conduct a comparative study of a tin-lead solder and a lead-free solder in two key surface mount technology (SMT) processes. The two SMT processes in question were the stencil printing process and the reflow soldering process. Unreplicated fractional factorial experimental designs were used to carry out the studies. The quality of paste deposition in terms of height and volume were the characteristics of interest in the stencil printing process. The quality of solder joints produced in the reflow soldering experiment was assessed using x-ray and cross sectional analysis. This provided qualitative data that was then uniquely scored and weighted using a method developed during the research. Nested experimental design techniques were then used to analyse the resulting quantitative data. Predictive models were developed that allowed for the optimisation of both processes. Results from both experiments show that solder joints of comparable quality to those produced using tin-lead solder can be produced using lead-free solder in current SMT processes.

Enterobactérias Patogênicas: seu isolamento das águas superficiais por meio de precipitação química

Enterobacteria of pathogenic group were isolated directly of superficial waters using Alumina Milk as precipitate, being 23 Salmonella, 19 Shigella and 17 Proteus from 18 samples which were collected in brooks and rivers of São Paulo, Brazil.

Ocorrência de montmorilonita em alguns solos desenvolvidos do arenito de Botucatu

Este trabalho foi realizado com o objetivo de estudar a ocorrência de montmorilonita em solos desenvolvidos do arenito de Botucatu no município de Piracicaba. Tais solos são os seguintes: Regossol (série Ribeirão Claro), Podzólico Vermelho Amarelo-variação Laras (série Ibitiruna) e Regossol "intergrade". para Podzólico Vermelho Amarelo. Foram selecionados cinco perfis, sendo dois pertencentes ao Regossol (perfis P1, e Ρ2), dois ao Podzólico (perfis P3 e P4) e um ao Regossol "intergrade" (perfil Ρ5). As amostras dos cinco perfis, em número de 33, foram tratadas convenientemente para se processar a eliminação de sais solúveis e agentes cimentantes (matéria orgânica, óxidos de ferro livres, etc), e assim facilitar o estudo da fração argila. Nesta fração foram feitas as determinações químicas (% de K2O, silica, alumina e C.T.C.) e mineralógicas (raios X e análise térmica diferencial). Também determinações granulométricas e químicas foram realizadas em todas as amostras. Os perfis Ρ1 e P2, que não apresentaram rocha consolidada, tiveram a caolinita como mineral dominante (acima de 50%). Os perfis Ρ3, Ρ4 e Ρ5, que apresentaram como material de origem a rocha arenítica consolidada, tiveram a montmorilonita como mineral dominante, apresentando todavia, diferenças quanto ao teor desse mineral. Assim, o Podzólico Vermelho Amarelo-variação Laras, que possui o arenito de Botucatu de estratificação plano-paralela como material originário, teve um teor médio de montmorilonita de 35%, enquanto que o Regossol "intergrade" para Podzólico Vermelho Amarelo, com o mesmo arenito, mas de estratificação cruzada como material originário apresentou um teor médio de montmorilonita de 57%. A presença da montmorilonita nestes dois solos se deve a uma herança do material originário e não à formação local, por intemperização. Neste caso, o material originário deve ter tido, em outras épocas, condições favoráveis para a formação deste mineral, ou seja, clima semi-árido, riqueza de Ca, Mg, Na, baixa relação Si/Al e baixo teor de H. Pelos resultados obtidos, os perfis Ρ1 e P2), parecem não pertencer ao arenito de Botucatu. Infelizmente, devido à falta de dados mineralógicos da rocha do arenito de Botucatu de outras regiões do Estado, não foi possível verificar se a ocorrência da montmorilonita é ou não comum neste arenito. Outras pesquisas devem ser executadas visando este objetivo.

Decoloración de tintes por lacasa

Informe de investigación realizado a partir de una estancia en el Instituto de Biotecnología Medioambiental de la Universidad Tecnológica de Graz, Austria, entre Julio y Agosto de 2006. Se ha estudiado la decoloración de varios tintes sintéticos de estructuras químicas diferentes (Rojo Congo, Azul de Naftol, Indigo Carmín, Lanaset Gris, Azul de Nilo) por la enzima lacasa inmovilizada. La inmovilización de la enzima lacasa se llevó a cabo sobre esferas de alúmina (Al2O3) de 3 mm de diámetro debido a la resistecia mecánica de este material. La lacasa y la proteína inmovilizada se determinaron como la diferencia entre las concentraciones iniciales y residuales (obtenidas en los lavados). El porcentaje de lacasa inmovilizada fue del 68% y la cantidad de proteína inmovilizada por gramo de soporte de 5,6 mg. La enzima lacasa inmovilizada fue capaz de decolorar tintes de diferente estructura sin la necesidad de añadir mediadores redox, lo cual la hace una enzima muy adecuada para su aplicación en la decoloración de efluentes procedentes de la industria textil. De todas formas, son necesarios más estudios para optimizar la técnica de inmovilización así como el proceso de decoloración. Es interesante destacar que aunque hay muchos estudios basados en la oxidación de tintes textiles por lacasa la mayoría utilizan la enzima libre y hay muy poca información disponible sobre la aplicación de lacasas inmovilizadas, por lo que el presente estudio constituye una aportación muy interesante y novedosa.

Anàlisi dels contaminants orgànics persistents en Citharus linguatula en el litoral català

S’ha estudiat la bioacumulació de contaminants orgànics persistents en el múscul d’una espècie de peix en dos punts del litoral català: al Port de Barcelona i a la costa de Blanes. Citharus linguatula ha estat escollida per les seves característiques d’hàbitats (està més exposada a la contaminació al ser una espècie bentònica). La metodologia emprada consisteix en la homogeneïtzació amb sulfat de sodi i una extracció assistida amb microones amb n-hexà-acetona(1:1 v/v) durant 20 minuts. Els extractes es netegen i es fraccionen amb una columna cromatogràfica d’alúmina que permet la separació dels extractes en dos fraccions: un amb la majoria dels compostos organoclorats (hexaclorbenzè, DDTs, ciclodiens clorats i policlorbifenils) i l’altre amb els isòmers hexaclorciclohexans i els PAHs. Aquestes dos fraccions són posteriorment analitzades en el GC-MS. S’ha pogut corroborar l’elevada presència de PCBs a Barcelona, així com que en aquest punt de mostreig les espècies estan més exposades a la contaminació per organoclorats. S’ha identificat la presència de DDTs en els dos llocs estudiats. Pel que fa als PAHs s’ha pogut observar que a Barcelona també hi ha més presència d’aquests. Cal destacar que la concentració obtinguda dels compostos no es pot donar com a vàlida per l’existència d’indicis d’errors experimentals o d’injecció.

Enriched basaltic andesites from mid-crustal fractional crystallization, recharge, and assimilation (Pilavo Volcano, Western Cordillera of Ecuador)

The origin of andesite is an important issue in petrology because andesite is the main eruptive product at convergent margins, corresponds to the average crustal composition and is often associated with major Cu-Au mineralization. In this study we present petrographic, mineralogical, geochemical and isotopic data for basaltic andesites of the latest Pleistocene Pilavo volcano, one of the most frontal volcanoes of the Ecuadorian Quaternary arc, situated upon thick (30-50 km) mafic crust composed of accreted Cretaceous oceanic plateau rocks and overlying mafic to intermediate Late Cretaceous-Late Tertiary magmatic arcs. The Pilavo rocks are basaltic andesites (54-57 center dot 5 wt % SiO(2)) with a tholeiitic affinity as opposed to the typical calc-alkaline high-silica andesites and dacites (SiO(2) 59-66 wt %) of other frontal arc volcanoes of Ecuador (e.g. Pichincha, Pululahua). They have much higher incompatible element contents (e.g. Sr 650-1350 ppm, Ba 650-1800 ppm, Zr 100-225 ppm, Th 5-25 ppm, La 15-65 ppm) and Th/La ratios (0 center dot 28-0 center dot 36) than Pichincha and Pululahua, and more primitive Sr ((87)Sr/(86)Sr similar to 0 center dot 7038-0 center dot 7039) and Nd (epsilon(Nd) similar to +5 center dot 5 to +6 center dot 1) isotopic signatures. Pilavo andesites have geochemical affinities with modern and recent high-MgO andesites (e.g. low-silica adakites, Setouchi sanukites) and, especially, with Archean sanukitoids, for both of which incompatible element enrichments are believed to result from interactions of slab melts with peridotitic mantle. Petrographic, mineral chemistry, bulk-rock geochemical and isotopic data indicate that the Pilavo magmatic rocks have evolved through three main stages: (1) generation of a basaltic magma in the mantle wedge region by flux melting induced by slab-derived fluids (aqueous, supercritical or melts); (2) high-pressure differentiation of the basaltic melt (at the mantle-crust boundary or at lower crustal levels) through sustained fractionation of olivine and clinopyroxene, leading to hydrous, high-alumina basaltic andesite melts with a tholeiitic affinity, enriched in incompatible elements and strongly impoverished in Ni and Cr; (3) establishment of one or more mid-crustal magma storage reservoirs in which the magmas evolved through dominant amphibole and clinopyroxene (but no plagioclase) fractionation accompanied by assimilation of the modified plutonic roots of the arc and recharge by incoming batches of more primitive magma from depth. The latter process has resulted in strongly increasing incompatible element concentrations in the Pilavo basaltic andesites, coupled with slightly increasing crustal isotopic signatures and a shift towards a more calc-alkaline affinity. Our data show that, although ultimately originating from the slab, incompatible element abundances in arc andesites with primitive isotopic signatures can be significantly enhanced by intra-crustal processes within a thick juvenile mafic crust, thus providing an additional process for the generation of enriched andesites.

A compositional data analysis package for R providing multiple approaches

”compositions” is a new R-package for the analysis of compositional and positive data.It contains four classes corresponding to the four different types of compositional andpositive geometry (including the Aitchison geometry). It provides means for computation,plotting and high-level multivariate statistical analysis in all four geometries.These geometries are treated in an fully analogous way, based on the principle of workingin coordinates, and the object-oriented programming paradigm of R. In this way,called functions automatically select the most appropriate type of analysis as a functionof the geometry. The graphical capabilities include ternary diagrams and tetrahedrons,various compositional plots (boxplots, barplots, piecharts) and extensive graphical toolsfor principal components. Afterwards, ortion and proportion lines, straight lines andellipses in all geometries can be added to plots. The package is accompanied by ahands-on-introduction, documentation for every function, demos of the graphical capabilitiesand plenty of usage examples. It allows direct and parallel computation inall four vector spaces and provides the beginner with a copy-and-paste style of dataanalysis, while letting advanced users keep the functionality and customizability theydemand of R, as well as all necessary tools to add own analysis routines. A completeexample is included in the appendix

Effects of Crypthecodiniumcohnii, Chlorela spp. e Isochrysisgalbana addition to milk replacer on goat kids and lamb growth.

The effects of Crypthecodinium cohnii (Cryp.), Chlorela spp. (Chlo.) and Isochrysis galbana (Iso.) addition to milk replacer on goat kids and lambs growth were evaluated. About 80 Majorera goat kids (males and females) and 80 Canarian sheep lambs were randomly assigned into four different groups (by specie) according to diet. Control groups were fed with a commercial milk replacer at 16% (w/w); Cryp. groups received a commercial milk replacer (15.1% w/w) supplemented with 9 g of a paste of C. cohnii; Chlo. groups received a commercial milk replacer (15.1% w/w) supplemented with 9 g of a paste of Chlorela spp.; Iso. groups received a commercial milk replacer (15.1% w/w) supplemented with 9 g of a paste of I. galbana. After colostrum period, animals were individually bottle-fed twice daily (8 am and 8 pm) ad libitum with the corresponding diet until day 60 of life. Animals were weighted every week at 8 am and liquid diet intake was recorded weekly. No effects of microseaweed addition were observed, neither growth nor milk replacer intake.

Synthesis of bone-like structured foams

Here we present a processing route to produce multi-structured ceramic foams based on the combination of particle-stabilized foams with polymeric sponges to produce positive and negative templating structures. Polyester sponges are infiltrated with freshly produced calcium aluminate alumina foams and upon sintering either positive templating structures are produced when wetting the sponges, or negative templating foams with a percolating pore network are obtained when completely filling the sponges. Additionally, by combining different layers of these particle-stabilized foam infiltrated sponges, various different structures can be produced, including sandwich structures, pore size gradients, and ceramic bone-like structures applying to different types of bone. The particle-stabilized foams used were in situ self-hardening calcium aluminate cement enriched alumina foams to obtain crack-free samples with pore interconnections and tailorable pore sizes.