Blends based on sulfonated poly[bis(benzimidazobenzisoquinolinones)] and poly(vinylidene fluoride) for polymer electrolyte membrane fuel cell

A new blend system consisting of an amorphous sulfonated poly[bis(benzimidazobenzisoquinolinones)] (SPBIBI) and the semi-crystalline poly(vinylidene fluoride) (PVDF) was prepared for proton exchange membranes. The miscibility behavior of a series of blends of SPBIBI with PVDF at various weight ratios was studied by WXRD, DSC and FTIR. The properties of the blend membranes were investigated, and it was found that the introduction of PVDF in the SPBIBI matrix altered the morphological structure of the blend membranes, which led to the formation of improved connectivity channels. For instance, the conductivity of the blend membrane containing 10 wt% PVDF displayed the highest proton conductivity (i.e., 0.086 S cm(-1)) at room temperature, a value almost twofold that of the pristine SPBIBI membranes (i.e., 0.054S cm(-1)) under identical conditions.

Investigations of the properties of Mg-5Al-0.3Mn-xCe (x=0-3, wt.%) alloys

Mg-5Al-0.3Mn-xCe (x = 0-3, wt.%) alloys were prepared by metal mould casting method. The microstructures and mechanical properties were investigated. The results revealed that the main phases of as-cast Mg-5Al-0.3Mn alloy consist of alpha-Mg matrix and beta-Mg17Al12 phase. With the addition of Ce element, Al11Ce3 precipitates were formed and mainly aggregated along the grain boundaries. The amount of the Al11Ce3 precipitates increased with increasing addition of Ce, but the amount of beta-Mg17Al12 phase decreased. The highest tensile strength was obtained in Mg-5Al-0.3Mn-1.5Ce alloy. The ultimate tensile strength (UTS), yield strength (YS) and elongation at room temperature are 203 MPa, 88 MPa and 20%, separately.

Effect of cerium on microstructure and electrochemical performance of Ti-V-Cr-Ni electrode alloy

Effect of cerium on the microstructure and electrochemical performance of the Ti0.25V0.35-xCexCr0.1Ni0.3 (x = 0, 0.005) electrode alloy was investigated by X-ray diffraction (XRD), field emission scanning electron microscopy/energy dispersive X-ray spectrometry (FESEM-EDS), and electrochemical impedance spectroscopy (EIS) measurements. On the basis of XRD and FESEM-EDS analysis, the alloy was mainly composed of V-based solid solution with body-centered-cubic structure and TiNi-based secondary phase. Ce did not exist in two phases, instead, it existed as Ce-rich small white particles, with irregular edges, distributed near the grain boundaries of the V-based solid solution phase. Discharge capacity, cycle stability, and high-rate discharge ability of the alloy electrode were effectively improved with the addition of Ce at 293 K. It was very surprising that the charge retention was abnormal with larger discharge capacity after standing at the open circuit for 24 h. EIS indicated that addition of Ce improved the dynamic performance, which caused the charge transfer resistance (R-T) to decrease and exchange current density (I-0) to increase markedly. The exchange current density of the electrochemical reaction on the alloy surface with Ce addition was about 2.07 and 3.10 times larger than that of the alloy without Ce at 303 and 343 K, respectively.

CPE-g-HEA/TDI热塑性弹性体的制备和性能研究

采用氯化原位接枝法合成主链为氯化聚乙烯(CPE)、支链为丙烯酸-2-羟基乙酯（HEA）的官能化接枝聚合 物(CPE-g-HEA),制备CPE-g-HEA/2,4-二异氰酸甲苯酯（TDI）热塑性弹性体,并对其性能进行研究。结果表明, CPE-g-HEA/TDI热塑性弹性体的物理性能较好;与溶液法产物相比,共混法CPE-g-HEA/TDI热塑性弹性体的强度 较大、相对分子质量较小、相对分子质量分布较宽,热行为基本无变化;共混法CPE-g-HEA/TDI热塑性弹性体的反 应温度应控制在60～70℃,共混次数(即打三角包次数) 为150次时拉伸强度较高、80次时拉断伸长率较高,HEA/TDI摩尔比为1/0.5时拉伸强度较高。

Negative differential resistance and memory effect in diodes based on 1,4-dibenzyl C60 and zinc phthalocyanine doped polystyrene hybrid material

Negative differential resistance (NDR) and memory effect were observed in diodes based on 1,4-dibenzyl C60 (DBC) and zinc phthalocyanine doped polystyrene hybrid material. Certain negative starting sweeping voltages led to a reproducible NDR, making the hybrid material a promising candidate in memory devices. It was found that the introduction of DBC enhanced the ON/OFF current ratio and significantly improved the memory stability. The ON/OFF current ratio was up to 2 orders of magnitude. The write-read-erase-reread cycles were more than 10(6), and the retention time reached 10 000 s without current degradation.

一种钛白粉表面无机-有机包覆的方法

一种钛白粉表面无机－有机包覆的方法是在钛白粉表面包覆一层铝，以增加钛白粉的耐候性和白度以及水中分散性，然后再利用甲基含氢硅油和六甲基二硅氮烷与钛白粉表面反应生成特殊的表面膜层，从而改善钛白粉在醇酸树脂中的分散性能。本发明具有操作简单、制作方便、反应条件温和，无二次污染，成本低的优点。

Electropolymerization of azure B on a screen-printed carbon electrode and its application to the determination of NADH in a flow injection analysis system

The electrooxidation polymerization of azure B on screen-printed carbon electrodes in neutral phosphate buffer was studied. The poly(azure B) modified electrodes exhibited excellent electrocatalysis and stability for dihydronicotinamide adenine dinucleotide (NADH) oxidation in phosphate buffer (pH 6.9), with an overpotential of more than 400 mV lower than that at the bare electrodes. Different techniques, including cyclic voltammetry, scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy have been employed to characterize the poly (azure B) film. Furthermore, the modified screen-printed carbon electrodes were found to be promising as an amperometric detector for the flow injection analysis (FIA) of NADH, typically with a dynamic range of 0.5 muM to 100 muM.

Independence of the brittle-ductile transition from the rubber particle size for impact-modified poly(vinyl chloride)

A series of acrylic impact modifiers (AIMS) with different particle sizes ranging from 55.2 to 927.0 nm were synthesized by seeded emulsion polymerization, and the effect of the particle size on the brittle-ductile transition of impact-modified poly(vinyl chloride) (PVC) was investigated. For each AIM, a series of PVC/AIM blends with compositions of 6, 8, 10, 12, and 15 phr AIM in 100 phr PVC were prepared, and the Izod impact strengths of these blends were tested at 23 degrees C. For AIMs with particle sizes of 55.2, 59.8, 125.2, 243.2, and 341.1 nm, the blends fractured in the brittle mode when the concentration of AIM was lower than 10 phr, whereas the blends showed ductile fracture when the AIM concentration reached 10 phr. It was concluded that the brittle-ductile transition of the PVC/AIM blends was independent of the particle size in the range of 55.2-341.1 nm. When the particle size was greater than 341.1 nm, however, the brittle-ductile transition shifted to a higher AIM concentration with an increase in the particle size. Furthermore, the critical interparticle distance was found not to be the criterion of the brittle-ductile transition for the PVC/AIM blends.

High-efficiency spin-coated organic light-emitting diodes based on a europium complex

An organic light-emitting diode fabricated by doping a europium, complex tris(dibiphenoylmethane)-mono (phenanthroline)-europium (Eu(DBPM)(3) (Phen)) into polymer poly(2-methoxy-5-(2-ethyl-hexyloxy)-1,4-phenylene) and poly(N-carbazole) was realized by spin coating. Comparison with other europium complexes, due to the existence of a larger spectral overlap between Eu(DBPM)(3)(Phen) and poly(2-methoxy-5-(2-ethyl-hexyloxy)-1,4phenylene), a high efficiency red emission was achieved. The device showed a turn-on voltage of 5.2 V The maximum efficiency reached 0.47 cd/A at luminance of 50 cd/m(2). The maximum luminance can reach 150 cd/m(2) at 95 mA/cm(2). To the best of our knowledge, this is one of the best results based on europium complexes by spin-casting method.

Anion coordination and molecular assembly in C2-substituted thiamine-anion systems: effects of the anion and molecular conformation

The compounds (het)(PtCl6)2H(2)O 1, (het)(HgI4).H2O 2 (het = 2-(alpha-hydroxyethyl)thiamine) and (hpt)(Hg2Br6) 3 (hpt = 2-(alpha-hydroxypropyl)thiamine) have been prepared and structurally characterized by X-ray crystallography in order to study the influence of the anion and molecular conformation on the formation of supramolecular architectures that adsorb anionic species. Both het and hpt molecules adopt the usual S conformation for C2-substituted thiamine but differ from the F conformation for C2-free thiamine derivatives. Two types of characteristic ligand-anion complexation are observed, being of the forms C(6')-H...anion...thiazolium-ring (in 1 and 2) and N(4'1)-H...anion...thiazolium-ring (in 3). The reaction of het with PtCl62- or HgI42- gives a 1-D double-chain in 1, consisting of two hydrogen-bonded het chains, which are cross-linked by anions through hydrogen bonding and anion...aromatic-ring interactions, or a cationic 3-D framework in 2 formed by the stacking of hydrogen-bonded sheets with anion-and-water-filled channels. In the case of 3, hydrogen-bonded hpt dimers and HgBr62- anions form alternate cation-anion columns. A comparison with the cases of C2-free thiamine-anion complexes indicates that the change in molecular conformation results in novel supramolecular assemblies in 1 and 2 and an analogous architecture in 3, which also depends on the nature of the anions.

Synthesis and structural characterization of a new molecule-based complex constructed from dodecamolybdophosphoric acid and imidazole

A new compound, (CH5N2)(3)(PMo12O40CH4N23H2O)-C-.-H-. (1), was synthesized and structurally characterized by elemental analyses, IR spectra, UV spectra, NMR spectra and ESR spectra. This is, to our knowledge, the first example of an imidazole-polyoxometalate species. The compound was recrystallized from N,N-dimethylformamide (DMF), and then black block-like crystals of (C3H5N2)(4)((PMoMo11O40)-Mo-V-O-VI)(.)4C(3)H(7)NO(.) 2H(2)O (2), were obtained. It crystallizes in a triclinic space group P (1) over bar with n=12.423(3) Angstrom, b=12.666(3) Angstrom, c=13.341(3) Angstrom, alpha=70.56(3)degrees, beta=71.16(3)degrees, gamma=64.18(3)degrees, V= 1742.3(6) Angstrom(3), Z=1, R1 = 0.0585, wR2 = 0.1885. An X-ray crystallographic study showed that the crystal structure is constructed by electrostatic attractions and hydrogen bonds between a dodecamolybdophosphoric anion and an imidazole. The imidazole and DMF molecules occupy cavities in a polyoxometalate lattice ordered along a c-axis. The structure of (2) is similar to that of (1) from a comparison of both IR spectra and TGA Curves.

Hydrothermal synthesis and crystal structure of an unusual compound: [Cu(en)(2)](4)[(SiMo8V4O40)-O-V((VO)-O-IV)(2)][MoO4](2)center dot 5H(2)O

A novel compound [Cu(en)(2)](4)[(SiMo8V4O40)-O-v(V-IV O)(2)] [MoO4](2) . 5H(2)O has been hydrothermally synthesized and structurally characterized by single-crystal X-ray diffraction. Black crystals crystallize in the tetragonal. system, space group 14/m, a = b = 14.019(2) Angstrom, c = 20.341(4) Angstrom, V = 3997.9(11) Angstrom(3), Z = 2, lambda(MoKalpha) = 0.71073 Angstrom (R(F) = 0.0443 for 1819 reflections). Data were collected on a Siemens P4 four-circle diffractometer at 293 K in the range of 1.76 < theta < 24.98degrees using the omega-scan technique. The structure was solved by the direct method and refined by the full-matrix least squares on F-2 method using the SHELXL-97 software. X-ray crystallographic study showed that the title compound contained a bicapped alpha-Keggin fragment [SiMo8 (V4O40)-O-v((VO)-O-IV)(2)](4-) polyoxoanion.

拟除虫菊酯类农药结构/急性毒性的三维定量构效关系

用比较分子力场分析(CoMFA)研究了拟除虫菊酯类农药的结构与急性毒性DL50(大鼠,口服)的关系,考察了网格结构和探针原子对结果的影响。得到模型的R2为0 99,标准偏差为0 88,说明立体效应和静电作用场是描述拟除虫菊酯类农药急性毒性和进行结构活性关系研究的重要结构参数。在模型中,立体能与静电能的贡献为0 82/0 18,说明起主要作用的是立体项,建立三维定量构效关系模型可以对该类新化合物的DL50进行预测。构建的三维结构/毒性模型用三维等高图来表示,如果结合分子杀虫活性的相关研究,可以用来指导新分子的结构设计。