Report of the baseline survey undertaken on the Chinese cage site in Napoleon Gulf, Northern Lake Victoria, 12 March 2012

The government of the People's Republic of China through a 2007 agreement with the Government of the Republic of Uganda, has establishment of an Agricultural Technology Demonstration Center (ATDC). The first phase covering the building of aquaculture infrastructure at Kajjansi ARDC is complete and the second operation phase has started in which facilities for cage culture have been set up in the Napoleon gulf, northern Lake Victoria near Jinja. The cage facility is aimed at boosting fish farming within the lake as a diversification to the traditional pond fish culture technology. NaFIRRI scientists as well as Chinese experts undertook a baseline survey in the chosen cage site on 12 March 2012. The survey covered determination of water depth, water transparency, measurement of selected physical-chemical parameters (temperature,dissolved oxygen, conductivity and pH; determination of the nutrient status and study of algae, invertebrate and fish communities at the site. Materials and methodologies used in the survey were based on the Standard Operating Procedures (SOPs) of NaFIRRI. The study area was divided into three study sites. Site 1 (upstream) was at 8.9 metre depth while site 2 (proposed cage site) and site 3 (downstream) were 6 and 4.3 metres deep respectively. Water transparency was lowest at site 1 (1.58 m) and highest at site 3 (1.64 m). Dissolved oxygen at the three sites ranged from 6.0 to 8 mg/I. Water temperature profiles fluctuated within narrow limits between 26.5 and 27.5 DC. Measurements of pH were between 7 (neutral) and 8 (alkaline) while electrical conductivity was between 98 and 101 uS/em. These observed physical-chemical parameters at the study site were considered suitable for cage fish rearing purposes. Nitrite-nitrogen levels varied within narrow limits from 0.043 to 0.0453 mgtl. Similarly, Ammonia-nitrogen varied between 0.015 and 0.0185 mg/1. Soluble reactive phosphorus (SRP) level was highest at site 3 (O.012mgll) compared to that at sites 1 and 2 (0.009mgll). Total suspended solids (TSS) were higher at site 1 (83.3mgll), thereafter decreasing to lower levels at sites 2 (24.8mgtl) and 3 (19.8mgl) respectively. The nutrient level results observed here all fall below the maximum permissible limits by NEMA and therefore the site is recommended for cage culture The algal community was constituted by four major groups: Blue greens,Greens, Cryptophytes, and Diatoms with blue greens as the common and dominant group. High algal biomass (19944961 ugtL) of the dominant blue green algae was observed at site 1 compared site 2 and 3 (58655.2 & 27487. 7 ugtL) respectively. Occurrence of toxicin producing algae: microsytis and cylindrospermopsis in the proposed cage area was considered to be of not much significance as their concentrations were below harmful levels. However, monitoring their presence, biomass and seasonality will be critical in order to follow when and where they occur and at what time of the year for ease of management of the cages

Fishery resource assessment and monitoring in the development and control of fisheries in the Lake Volta

Gill-netting and rotenoning have been used for assessing and monitoring fish stock abundance in Volta Lake. The lake and the main gear types used on it have been described. Before a gill-net sampling plan was set up, a preliminary survey was undertaken which largely determined the final form of the plan. An investigation as to whether or not the lake was being overfished concluded that it was being underfished. Commercial and experimental catch data analyses disclosed that the adults of the small species were being little utilized. Commercial sized species were also not being harvested according to their apparent proportion in the population. Production is presently fluctuating between approximately 37,000 and 40,000 tonnes. A high correlation between commercial and experimental catch was realized. Developments which have followed in the wake of stock assessment and monitoring studies include: introduction of monofilament nylon net, development of a special scoop net to permit mass harvest of clupeids after they have been attracted to light, and the design of a larger canoe which would help to extend the fishery into open water. New regulation and management policies will have to be formulated in the light of new findings before a rational exploitation of all the species can be achieved.

Studies on induced breeding of Clarias gariepinus (Burchell, 1822) in hapa pens

Induced breeding of Clarias gariepinus was conducted monthly in hapa pens, set up in Otamiri river for nineteen months (June 1993 - December 1994). Results of natural fertilization were unsatisfactory as few eggs were fertilized. Mean relative fecundity, percentage fertilization, percentage hatching and percentage fry survival were: 15.86 ± 1.95 x 10', 18.92 ± 5.28%, 13.50 ± 3.8% and 6.42 ± 0.72%. Results from artificial fertilization were as follows: Mean relative fecundity, 13.80 ± 2.85 x 10', percentage fertilization, 81.91 ± 2.28%, percentage hatching, 86.10 ± 2.46% and percentage fry survival, 21.40 ± 1.89% respectively. The success of artificial fertilization depended largely on the latency period of 9-11 hours and this suggests that induced breeding in pens is feasible. The poor results from natural fertilization were attributed to lack of adequate substrate for the male fish to display courtship and subsequent fertilization of eggs.

The role of satellite lakes in conservation of fish species diversity in the Lake Kyoga basin

Lakes Victoria and Kyoga had, a diverse fish fauna, which was important as food for local population and valuable in scientific studies. Over the past twenty years, the diversity of fish in these lakes had declined due to over-exploitation, introduction of new fish species including the piscivorous Nile perch and degradation of fish habitat. Studies of satellite lakes in the Victoria and Kyoga lake basins suggested that some of these lakes harboured species which had been lost from the main lakes. In order to better understand the extent, to which these satellite lakes may serve as refugia, a faunal survey was undertaken to determine the distribution and nature of the taxa found. Seven satellite lakes and the eastern end of the main Lake Kyoga adjacent to these minor lakes were surveyed over a two-year period for fish species diversity. A total of 68 fish species were recorded of which 41 were haplochromines. Almost all the native non cichlids which occurred in the main lakes (Victoria and Kyoga) before the Nile perch upsurge recorded. Lakes Nawampasa, Gigati, Kawi, Agu and Nyaguo had the highest fish species and trophic diversity. The trophic diversity of haplochromines (based on Shannon Weaver Index) was highest in Lake Nawampasa (1.28), followed by Gigati (1.25), Kawi (1.18), Agu (0.8), Lemwa (0.81), Nyaguo (0.35) and was lowest in the main Lake Kyoga. Potential threats to these lakes were from collectors of ornamental fish species, especially the haplochromines, the spread of the predatory Nile perch and the water hyacinth, which are already in Lake Kyoga, and the destruction of macrophytes through harvesting of papyrus and reclamation for agriculture. The human population around these lakes harvested the fishes for food but the levels of exploitation were still low because the lakes were adjacent to main Lake Kyoga, the major supply of fish. Ornamental fish dealers were encouraged to start captive breeding of the fish for export to reduce pressure on the lakes and demonstrations for breeding were set up at FIRI in Jinja. Meetings and seminars were held with some of the communities living around the lakes sampled and the importance of fish species found in these lakes and the dangers of destructive practices discussed. Representatives of all taxa of fish caught from the lakes were preserved, catalogued and stored in the FIRI Museum. Results from this survey support the motion that these satellite lakes are important refugia for endemic diversity. Based on survey, we recommend that SaIne of these lakes like Nawampasa, Gigati, Kawi, Agu and Nyaguo could be designated as conservation areas of species threatened in the main lakes. One of the factors that seem to have prevented the spread of Nile perch into Kyoga Minor lakes seems to have been the presence of extensive swamps around these lakes and the low oxygen levels that exist in these habitats. Clearing of swamps and vegetation that separate Kyoga minor lakes from the main lake should be avoided to prevent Nile perch from spreading into these lakes.

Everywhere and nowhere: nearshore software development in the context of globalisation

Offshore software development has been identified as one of the most striking manifestations of contemporary globalisation and as evidence of placelessness, the idea that information and communication technologies have rendered location irrelevant. Research in the International Business and Information Systems fields, in contrast, has suggested that all locations are not equal and has identified a number of characteristics that may influence the attractiveness of a location for multinational investment and offshoring, respectively. These literatures, however, focus almost exclusively on quantitative, economic characteristics that are seen as fixed and applying uniformly throughout a whole country. They therefore offer little guidance on the suitability of particular locations as offshoring destinations, especially in countries without a track record in offshore software development. Drawing on two cases of nearshore software development centres set up by offshore service providers in the Caribbean, this paper illustrates that, while the initial decision to establish the ventures reflected a logic of placelessness, characteristics of these particular locations affected their subsequent success. Through the findings, we therefore develop a typology of espoused, unanticipated and remediable locational characteristics, which illustrates that locational attractiveness may vary significantly within countries and that offshore service providers and government agencies can modify locational characteristics to their advantage.

Impact of carbon fibre/epoxy corrugated cores

The dynamic compressive response of corrugated carbon-fibre reinforced epoxy sandwich cores has been investigated using a Kolsky-bar set-up. Compression at quasi-static rates up to v 0=200ms -1 have been tested on three different slenderness ratios of strut. High speed photography was used to capture the failure mechanisms and relate these to the measured axial compressive stress. Experiments show significant strength enhancement as the loading rate increases. Although material rate sensitivity accounts for some of this, it has been shown that the majority of the strength enhancement is due to inertial stabilisation of the core members. Inertial strength enhancement rises non-linearly with impact velocity. The largest gains are associated with a shift to buckle modes composed of 2-3 half sine waves. The loading rates tested within this study are similar to those that are expected when a sandwich core is compressed due to a blast event. © 2012 Elsevier Ltd.

The rise heights of low-and high-Froude-number turbulent axisymmetric fountains

We present the results of an experimental investigation across a broad range of source Froude numbers, 0. 4 ≤ Fr 0 ≤ 45, into the dynamics, morphology and rise heights of Boussinesq turbulent axisymmetric fountains in quiescent uniform environments. Typically, these fountains are thought to rise to an initial height, z i, before settling back and fluctuating about a lesser (quasi-) steady height, z ss. Our measurements show that this is not always the case and the ratio of the fountain's initial rise height to steady rise height, λ = z i/z ss, varies widely, 0. 5 ≈ λ ≈ 2, across the range of Fr 0 investigated. As a result of near-ideal start-up conditions provided by the experimental set-up we were consistently able to form a vortex at the fountain's front. This enabled new insights into two features of the initial rise of turbulent fountains. Firstly, for 1. 0 ≈ Fr 0 ≈ 1. 7 the initial rise height is less than the steady rise height. Secondly, for Fr 0 ≈ 5. 5, the vortex formed at the fountain's front pinches off, separates from the main body and rises high above the fountain; there is thus a third rise height to consider, namely, the maximum vortex rise height, z v. From our observations we propose classifying turbulent axisymmetric fountains into five regimes (as opposed to the current three regimes) and present detailed descriptions of the flow in each. Finally, based on an analysis of the rise height fluctuations and the width of fountains in (quasi-) steady state we provide further insight into the physical cause of height fluctuations. © 2011 Cambridge University Press.

A six sensor method for measuring acoustic properties in ducts.

An accurate description of sound propagation in a duct is important to obtain the sound power radiating from a source in both near and far fields. A technique has been developed and applied to decompose higher-order modes of sound emitted into a duct. Traditional experiments and theory based on two-sensor methods are limited to the plane-wave contribution to the sound field at low frequency. Due to the increase in independent measurements required, a computational method has been developed to simulate sensitivities of real measurements (e.g., noise) and optimize the set-up. An experimental rig has been constructed to decompose the first two modes using six independent measurements from surface, flush-mounted microphones. Experiments were initially performed using a loudspeaker as the source for validation. Subsequently, the sound emitted by a mixed-flow fan has been investigated and compared to measurements made in accordance with the internationally standardized in-duct fan measurement method. This method utilizes large anechoic terminations and a procedure involving averaging over measurements in space and time to account for the contribution from higher-order modes. The new method does not require either of these added complications and gives detail about the underlying modal content of the emitted sound.

Designing intrinsically motivating user interfaces for the ageing population

Older people often find it difficult to learn to use new technology. Although they may want to adopt it, they can find the learning process challenging and frustrating and subsequently lose motivation. This paper looks at how psychological theories of intrinsic motivation could be applied to make the ICT learning process more engaging for older users and describes an experiment set up to test the applicability of these theories to user interface (UI) design. The results of the experiment confirmed that intrinsic motivation theory is a valid lens through which to look at current ICT design and also uncovered significant gender differences in reaction to different kinds of learning tasks. © 2013 Springer-Verlag Berlin Heidelberg.

Carbonating magnesia for soil stabilization

This paper investigates the potential for carbonating reactive magnesia (MgO) to serve as a more sustainable soil stabilization method by providing rapid and significant strength development of the stabilized soil through absorbing substantial quantities of CO2. Gaseous CO2 was forced through laboratory-prepared reactive MgO-treated soil samples in a triaxial cell set-up, and their resulting mechanical and microstructural properties were investigated using unconfined compressive strength, X-ray diffraction, and scanning electron microscopy. The results showed that adequately carbonated MgO-treated soils could, in a few hours, reach a similar strength range to corresponding 28 day Portland cement (PC)-stabilized soils. Hydrated magnesium carbonates, namely nesquehonite and hydromagnesite-dypingite, were the main products of the carbonated MgO in the soil, and were responsible for the significant strength development.

Sand column impact onto a Kolsky pressure bar

A laboratory-based methodology to launch cylindrical sand slugs at high velocities is developed. The methodology generates well-characterised soil ejecta without the need for detonation of an explosive; this laboratory-based tool thereby allows for the experimental investigation of the soil-structure events. The experimental set-up comprises a launcher with a cylindrical cavity and a piston to push out the sand slug. The apparatus is used to launch both dry and water-saturated sand slugs. High speed photography is used to characterise the evolution of the sand slugs after launch. We find that the diameter of the slugs remains unchanged, and the sand particles possess only an axial component of velocity. However, the sand particles have a uniform spatial gradient of axial velocity and this results in lengthening of the slugs as they travel towards their target. Thus, the density of the sand slugs remains spatially homogenous but decreases with increasing time. The velocity gradient is typically higher in the dry sand slugs than that of the water-saturated slugs. The pressure exerted by the slugs on a rigid-stationary target is measured by impacting the slugs against a direct impact Kolsky bar. After an initial high transient pressure, the pressure reduces to a value of approximately ρv 2 where ρ is the density of the impacting sand slug and v is the particle velocity. This indicates that loading due to the sand is primarily inertial in nature. The momentum transmitted to the Kolsky bar was approximately equal to the incident momentum of the sand slugs, regardless of whether they are dry or water-saturated. © 2013 Elsevier Ltd. All rights reserved.

Aeroacoustic source measurement methods for characterizing the sound generated by ducted flow devices with higher-order modes.

The International Organization for Standardization (ISO) method 5136 is widely used in industry and academia to determine the sound power radiated into a duct by fans and other flow devices. The method involves placing the device at the center of a long cylindrical duct with anechoic terminations at each end to eliminate reflections. A single off-axis microphone is used on the inlet and outlet sides that can theoretically capture the plane-wave mode amplitudes but this does not provide enough information to fully account for higher-order modes. In this study, the "two-port" source model is formulated to include higher-order modes and applied for the first three modes. This requires six independent surface pressure measurements on each side or "port." The resulting experimental set-up is much shorter than the ISO rig and does not require anechoic terminations. An array of six external loudspeaker sources is used to characterize the passive part of the two-port model and the set-up provides a framework to account for transmission of higher-order modes through a fan. The relative importance of the higher-order modes has been considered and their effect on inaccuracies when using the ISO method to find source sound power has been analyzed.

Effects of constructed wetland system on the removal of dibutyl phthalate (DBP)

Phthalic acid esters (PAEs) have become widely diffused in the environment via the manufacturing process. Numerous experiments have shown that the bioaccumulation of PAEs occurred in the aquatic and terrestrial food chain; meanwhile, it was found that some of PAEs were considered as potential carcinogens, teratogens and mutagens. In this research, two vertical/reverse-vertical flow constructed wetland systems were set up to study its removal efficiency of dibutyl, phthalate (DBP) pollution. The results showed that the constructed wetland system could remove DBP effectively, and the removal rates reached nearly 100%. Substrate microorganism and enzymatic activities probably played key roles during DBP removal, and the removal of DBP probably mainly took place in the upper layer of chamber A in the constructed wetland systems. (C) 2007 Elsevier GmbH. All rights reserved.

Noise and vibration in brushless doubly fed machine and brushless doubly fed reluctance machine

This study investigates modes of vibration in brushless doubly fed machine and brushless doubly fed reluctance machine due to the interaction of its fundamental magnetic fields, via the bending forces they set up in the back iron. It is shown that the presence of two field components of different pole numbers leads to vibration components in addition to those that would be expected in single field machines such as the induction motor. Formulations for the frequencies and magnitudes of the expected vibration components are given and verified experimentally. It is shown that the strength of the vibration components is highly dependent on the choice of pole numbers in the machine, with some much worse than equivalent induction machines and some very similar. The methodology presented enables designers to determine whether their machines are likely to suffer from vibration problems in advance of construction, and to apply remedies where appropriate. © The Institution of Engineering and Technology 2014.

Physical properties of a hybrid and a nanohybrid dental light-cured resin composite.

This work was aimed at the study of some physical properties of two current light-cured dental resin composites, Rok (hybrid) and Ice (nanohydrid). As filler they both contain strontium aluminosilicate particles, however, with different size distribution, 40 nm-2.5 mum for Rok and 10 nm-1 mum for Ice. The resin matrix of Rok consists of UDMA, that of Ice of UDMA, Bis-EMA and TEGDMA. Degree of conversion was determined by FT-IR analysis. The flexural strength and modulus were measured using a three-point bending set-up according to the ISO-4049 specification. Sorption, solubility and volumetric change were measured after storage of composites in water or ethanol/water (75 vol%) for 1 day, 7 or 30 days. Thermogravimetric analysis was performed in air and nitrogen atmosphere from 30 to 700 degrees C. Surface roughness and morphology of the composites was studied by atomic force microscopy (AFM). The degree of conversion was found to be 56.9% for Rok and 61.0% for Ice. The flexural strength of Rok does not significantly differ from that of Ice, while the flexural modulus of Rok is higher than that of Ice. The flexural strengths of Rok and Ice did not show any significant change after immersion in water or ethanol solution for 30 days. The flexural modulus of Rok and Ice did not show any significant change either after immersion in water for 30 days, while it decreased significantly, even after 1 day immersion, in ethanol solution. Ice sorbed a higher amount of water and ethanol solution than Rok and showed a higher volume increase. Thermogravimetric analysis showed that Rok contains about 80 wt% inorganic filler and Ice about 75 wt%.