997 resultados para impulsive systems
Resumo:
This paper proposes a wireless EEG acquisition platform based on Open Multimedia Architecture Platform (OMAP) embedded system. A high-impedance active dry electrode was tested for improving the scalp- electrode interface. It was used the sigma-delta ADS1298 analog-to-digital converter, and developed a “kernelspace” character driver to manage the communications between the converter unit and the OMAP’s ARM core. The acquired EEG signal data is processed by a “userspace” application, which accesses the driver’s memory, saves the data to a SD-card and transmits them through a wireless TCP/IP-socket to a PC. The electrodes were tested through the alpha wave replacement phenomenon. The experimental results presented the expected alpha rhythm (8-13 Hz) reactiveness to the eyes opening task. The driver spends about 725 μs to acquire and store the data samples. The application takes about 244 μs to get the data from the driver and 1.4 ms to save it in the SD-card. A WiFi throughput of 12.8Mbps was measured which results in a transmission time of 5 ms for 512 kb of data. The embedded system consumes about 200 mAh when wireless off and 400 mAh when it is on. The system exhibits a reliable performance to record EEG signals and transmit them wirelessly. Besides the microcontroller-based architectures, the proposed platform demonstrates that powerful ARM processors running embedded operating systems can be programmed with real-time constrains at the kernel level in order to control hardware, while maintaining their parallel processing abilities in high level software applications.
Resumo:
The significant number of publications describing unsuccessful cases in the introduction of health information systems makes it advisable to analyze the factors that may be contributing to such failures. However, the very notion of success is not equally assumed in all publications. Based in a literature review, the authors argue that the introduction of systems must be based in an eclectic combination of knowledge fields, adopting methodologies that strengthen the role of organizational culture and human resources in this project, as a whole. On the other hand, the authors argue that the introduction of systems should be oriented by a previously defined matrix of factors, against which the success can be measured.
Resumo:
Graphical user interfaces (GUIs) are critical components of today's open source software. Given their increased relevance, the correctness and usability of GUIs are becoming essential. This paper describes the latest results in the development of our tool to reverse engineer the GUI layer of interactive computing open source systems. We use static analysis techniques to generate models of the user interface behavior from source code. Models help in graphical user interface inspection by allowing designers to concentrate on its more important aspects. One particular type of model that the tool is able to generate is state machines. The paper shows how graph theory can be useful when applied to these models. A number of metrics and algorithms are used in the analysis of aspects of the user interface's quality. The ultimate goal of the tool is to enable analysis of interactive system through GUIs source code inspection.
Resumo:
The objective of this study was to evaluate split nitrogen (N) fertilization of maize applied in band at sowing and top dressing with and without crop rotation, under no-till. The experiment was conducted with six N rates at sowing (0, 20, 30, 40, 50 and 60 kg ha-1) combined with three rates in top dressing (40, 70, 100 kg ha-1) and two management systems: after five cropping sequences of maize and crop rotation (maize + soybean + oat + soybean + corn) in a randomized block design with four replications. The crop rotation system increased yield in approximately 7% in relation to the area without rotation. The split of nitrogen fertilization, in rates above 39 and 54 kg ha-1 at sowing and 70 and 40 kg ha-1 in top dressing, resulted in yield higher than that obtained with the application of 100 kg ha-1 in top dressing. Grain yield was higher with the rates 50 and 70 kg ha-1 of N compared with that obtained with 20 and 100 kg ha-1 at sowing and top dressing, respectively. The rate 70 kg ha-1 of N resulted in the highest yield at the lowest cost compared with the revenues and costs incurred with the rates 40 and 100 kg ha-1.
Resumo:
Purpose – The purpose of this paper is to propose a generic model of Integrated Management System of Quality, Environment and Safety (IMS-QES) that can be adapted and progressively to assimilate various Management Systems, of which highlights: ISO 9001 for Quality; ISO 14001 for Environment; OHSAS 18001 for Occupational Health and Safety. Design/methodology/approach – The model was designed in the real environment of a Portuguese Organization and 160 employees were surveyed. The rate response was equal to 86 percent. The conceived model was implemented in a first phase for the integration of Quality, Environment and Safety Management Systems. Findings – Among the main findings of the survey the paper highlights: the elimination of conflicts between individual systems with resources optimization; creation of added value to the business by eliminating several types of wastes; the integrated management of sustainability components in a global market; the improvement of partnerships with suppliers of goods and services; reducing the number of internal and external audits. Originality/value – This case study is one of the first Portuguese empirical researches about IMS-QES and the paper believes that it can be useful in the creation of a Portuguese guideline for integration, namely the Quality Management Systems; Environmental Management Systems and Occupational Health and Safety Management Systems among others.
Resumo:
Nowadays, there exist various standards for individual management systems (MSs), at least, one for each stakeholder. New ones will be published. An integrated management system (IMS) aims to integrate some or all components of the business into one coherent and efficient MS. Maximizing integration is more and more a strategic priority in that it constitutes an opportunity to eliminate and/or reduce potential factors of destruction of value for the organizations and also to be more competitive and consequently promote its sustainable success. A preliminary investigation was conducted on a Portuguese industrial company which, over the years, has been adopting gradually, in whole or in part, individualized management system standards (MSSs). A research, through a questionnaire, was performed with the objective to develop, in a real business environment, an adequate and efficient IMS-QES (quality, environment, and safety) model and to potentiate for the future a generic IMS model to integrate other MSSs. The strategy and research methods have taken into consideration the case study. It was obtained a set of relevant conclusions resulting from the statistical analyses of the responses to the survey. Globally, the investigation results, by themselves, justified and prioritized the conception of a model of development of the IMS-QES and consequent definition and validation of a structure of an IMS-QES model, to be implemented at the small- and medium-sized enterprise (SME) where the investigation was conducted.
Resumo:
The performance, carcass traits and finishing costs of Suffolk lambs were evaluated in three systems: (1) lambs weaned with 22 kg of body weight (BW) and supplemented with concentrate on pasture until slaughter; (2) lambs weaned with 22 kg BW and fed in feedlot until slaughter; (3) lambs maintained in controlled nursing after 22 kg BW and creep fed in feedlot until slaughter. Average daily gain (ADG) was 224 g/d for lambs weaned and supplemented with concentrate on pasture, 386 g/d for lambs weaned in feedlot and 481 g/d for lambs under controlled nursing. Empty body weight and visceral fat deposition were highest in lambs from feedlot systems. Carcass weights and carcass yields were highest for lambs in controlled nursing. Finishing total costs were highest in controlled nursing and lowest in the system with weaning in feedlot. High concentrate diet associated with controlled nursing in feedlot allowed lambs to reach the growth potential and carcasses with higher weights, higher yields and higher fat content. After weaning, lambs in feedlot fed with high concentrate diet had higher weight gain than lambs supplemented with concentrate on pasture. Carcasses produced under these two systems presented the same characteristics. The system with weaning in feedlot showed the lowest cost per kg carcass.
Resumo:
Lettuce (Lactuca sativa L.) is the most commonly consumed leaf vegetable in the Brazilian diet, and it is a good source of vitamins and minerals. It is widely grown in the conventional farming system. However, the hydroponic farming system has been gaining importance in the market, wining confidence from consumers, who are becoming increasingly more demanding on food quality. The objective of this study was to evaluate the performance of two lettuce cultivars on hydroponic and conventional farming systems for the production of fresh mass (FM) and dry mass (DM), photosynthesis, contents of chlorophyll and anthocyanin. The following two experiments were carried out: hydroponics farming (HF) and conventional farming (CF), performed in protect and unprotect environments, respectively, in Florianópolis, SC. Mimosa Verde cultivar (MV) showed greater fresh mass than Mimosa Roxa (MR), in both farming systems and the two cultivars presented better performance in the hydroponic system (287.7 g MV and 139.1 g MR) than the conventional system (129.7 g MV and 111.8 g MR). Mimosa Verde cultivar presented lower average contents of total chlorophyll (7.7 mg g-¹ FM) than Mimosa Roxa (11.8 mg g-¹FM), and both cultivars displayed higher means for this variable in the hydroponic farming system. Mimosa Roxa presented higher contents of anthocyanin in the conventional system (88.24 mg g-¹ FM) than the ones in the hydroponic system (36.89 mg g-¹ FM). The best results for CO2 net assimilation rate regarded to photosyntheticaly active photon flux density were found in the hydroponic system, for both lettuce cultivars. Variation in the contents of chlorophyll were also found. Those variations were higher in the protected system than in the hydroponic system and contents of anthocyanin were higher in the conventional system.
Resumo:
This study aimed to analyze the economic viability of the third milking in production systems using mechanical milking in a closed circuit, aiming to provide technicians and farmers with information to assist them in decision-making. Specifically, it intended: (a) to estimate the cost of one milking; (b) to estimate the cost of the third milking; (c) to develop a mathematical equation to estimate the minimum amount of milk produced with two milkings, from which it would be economically feasible to do the third milking. Data were collected from three dairy farms, from November 2010 to March 2011, keeping a twice-a-day milking frequency, with three data collections in each farm, totalizing nine collections. Considering the average data, it would be feasible to do the third milking if the average milk yield per day of lactating cows in a twice-a-day milking frequency was greater than or equal to 24.43 kg of milk.
Resumo:
Nanotechnology is the manipulation of matter on na almost atomic scale to produce new structures, materials, and devices. As potential occupational exposure to nanomaterials (NMs) becomes more prevalente, it is importante that the principles of medical surveillance and risk management be considered for workers in the nanotechnology industry.However, much information about health risk is beyond our current knowledge. Thus, NMs presente new challenges to understanding, predicting, andmanageing potential health risks. First, we briefly describe some general features of NMs and list the most importante types of NMs. This review discusses the toxicological potential of NMs by comparing possible injury mechanism and know, or potentially adverse, health effects. We review the limited research to date for occupational exposure to these particles and how a worker might be exposed to NMs. The principles of medical surveillance are reviewed to further the discussion of occupational health surveillance are reviewed to further the discussion of occupational health surveillance for workers exposed to NMs. We outlinehow occupational health professionals could contribute to a better knowledge of health effects by the utilization of a health surveillance program and by minimizing exposure. Finally, we discuss the early steps towards regulation and the difficulties facing regulators in controlling potentially harmful exposures in the absence of suficiente scientific evidence.
Resumo:
Risk management can be considered as part of the Occupational Health and Safety System (OHS) of an organization and can be used to develop and implement the OHS policy and manage the associated risks. The success of the integration of risk management in OHS depends on both technical and human aspects. Thus, this paper presents and discusses the case of a company working in the area of solid waste treatment. This company was certified in 2009 with an Integrated Management Systems for Quality, Environment, Occupational Health and Safety. The evolution of accidents before and after the implementation of the integrated system was analysed and a questionnaire was used to capture the perceptions of the technicians on the risk management system. The analysis of the findings showed that the frequency of accidents increased since 2009 but the severity has been reduced. Several interrelated causes and consequences were analysed and discussed. Furthermore, the analysis of the opinions of the company’s technicians permitted to highlight some important aspects on the integration of risk management in the OHS system of the company. In line with this discussion some hypothesis have been formulated.
Resumo:
The purpose of this paper is to, in a holistic way, identify and explore the critical success factors (CSFs) that are considered in the context of the growing discussions, movements, proposed models, and case studies about the integration of management systems (MSs). This work is an investigation focused on the integration of MSs into an integrated management system (IMS) and the proposed approach takes into account the literature review as well as the experience gained by the authors on researches about Portuguese enterprises. This qualitative and empirical research, investigated the integration of MSs from existing scientific publications for the period 1999 to 2014, on-going case studies and one inquiry conducted by the authors. This research contributes to a better understanding of the CSFs regarding the integration of MSs and thus provides an insight on the preventive management. This research shows an evident lack of information regarding case studies on CSFs for integrated management systems (IMSs) and has identified a set of relevant CSFs, for MSs integration and associated guidelines that organizations should take as a priority, in order to be able to manage, on a preventive way, the implementation of IMSs, and consequently to become more competitive with added value for the stakeholders.
Resumo:
Abstract: The growing proliferation of management systems standards (MSSs), and their individualized implementation, is a real problem faced by organizations. On the other hand, MSSs are aimed at improving efficiency and effectiveness of organizational responses in order to satisfy the requirements, needs and expectations of the stakeholders. Each organization has its own identity and this is an issue that cannot be neglected; hence, two possible approaches can be attended. First, continue with the implementation of individualized management systems (MSs); or, integrate the several MSSs versus related MSs into an integrated management system (IMS). Therefore, in this context, organizations are faced with a dilemma, as a result of the increasing proliferation and diversity of MSSs. This paper takes into account the knowledge gained through a case study conducted in the context of a Portuguese company and unveils some of the advantages and disadvantages of integration. A methodology is also proposed and presented to support organizations in developing and structuring the integration process of their individualized MSs, and consequently minimize problems that are generators of inefficiencies, value destruction and loss of competitiveness. The obtained results provide relevant information that can support Top Management decision in solving that dilemma and consequently promote a successful integration, including a better control of business risks associated to MSSs requirements and enhancing sustainable performance, considering the context in which organizations operate.
Resumo:
ABSTRACTIn no-tillage systems, straw coverage on soil surface is the key to success, and the choice of crops for rotation is crucial to achieve the sustainability and quality that conservation agriculture requires. The objective of this study was to evaluate the agronomic performance of the common bean cultivar IAC Formoso sown in succession to three straw mulch systems (corn alone, corn/Urochloa ruziziensisintercrop and U. ruziziensisalone) and topdress nitrogen rates (0; 40; 80; 120 and 160 kg ha-1N), at the four-leaf stage, three years after the implementation of no-tillage. The experiment was arranged in a randomized block split plot design, with three replications. Common bean highest yields were achieved in succession to U. ruziziensisalone and intercropped with corn. The corn/U. ruziziensisintercrop provided both straw and seed production, allowing for quality no-tillage. Topdressed nitrogen influenced the common bean yield when in succession to corn alone, U. ruziziensisalone and corn/U. ruziziensisintercrop in no-tillage.
Resumo:
Effective environmental management within companies, integrated with other management areas like quality and occupational health and safety, is nowadays assumed to be a strategic way to implement and improve lean and cleaner production. Also, sustainable development (SD) and business sustainability can be achieved through a better coordinated management of processes versus associated resources. This paper presents an in depth discussion regarding the promotion of integrated management systems, their benefits and major contribution towards the sustainable development of cleaner production related features. It addresses issues regarding the contributions resulting from the integration of standardized Management System (MS) from both internal and external perspectives. Complementing the overall review of aspects to the development of integrated management systems a survey was conducted in order to better understand the relevance of the identified success factors. The main findings in this paper are as follows: a contextualization model of sustainable development and integrated management systems considering the Triple Bottom Line: economic, social and environmental; and, a method and associated model to support the development of integrated management systems as well as general guidelines to support integration. It can be concluded that a proactive approach and commitment to cleaner production, supported by an integrated management system, brings relevant savings for organizations as well as providing value to the relevant interested parties.