The effect of feeding a high fibre diet on the welfare of sows housed in large dynamic groups

This study assessed the effect of increasing fibre levels in the concentrate ration on the welfare of sows housed in a large dynamic group. One hundred and twelve Large White x Landrace sows were allocated to one of two treatments over six replicates. Treatments were as follows: (i) High Fibre diet (similar to 15% CF [Crude Fibre]), and (ii) Control diet (similar to 5% CF). Treatments were applied to two separate dynamic groups each containing 33 (+/- 3) sows in a cross-over design, after three replicates the treatments were switched between the groups. Approximately nine sows were replaced in each of these groups at 3-week intervals (each replacement constituting a replicate of the study). Sows on the high fibre diet spent a greater percentage of time lying (High Fibre: 43.8, Control. 28.0, SEM 3.25%), while sows on the control diet spent more time sham chewing (High Fibre: 7.2, Control: 28.8, SEM 1.55%). Sows newly introduced to the group on the high fibre treatment spent proportionally more time in the kennel areas compared to newly introduced sows in the control treatment (High Fibre. 0.893, Control. 0 788, SEM 5 10) In general, aggression occurred at a very low frequency and overall levels did not differ between treatments (High Fibre: 0.005, Control: 0.003, SEM 0.0007 [occurrences per min)). However, sows in the control treatment performed head thrusting (High Fibre: 0.02, Control: 0.00, SEM 0.001 [occurrences per mini), and biting behaviour (High Fibre. 002, Control. 0.01, SEM 0.002 [occurrences per min]) more frequently than sows on the high fibre diet. There was no effect of treatment on physiological parameters such as plasma cortisol (High Fibre: 1.34, Control: 1.44, SEM 0.114 ng ml(-1)) or haptoglobin levels (High Fibre. 0.73, Control. 0.64, SEM 0.080 mg ml(-1)). In summary, provision of a high fibre diet had a positive effect on the welfare of group-housed dry sows Sows on the high fibre treatment spent more time resting in the kennel areas, less time performing stereotypic behaviours and showed a reduction in some aggressive behaviours relative to sows fed the control diet.

Monitoring of Corrosion in Structural Reinforcing Bars: performance comparison using in-situ fibre optic and electric wire strain gauge systems

Abstract This work addresses the problems of effective in situ measurement of the initiation or the rate of steel corrosion in reinforced concrete structures through the use of optical fiber sensor systems. By undertaking a series of tests over prolonged periods, coupled with acceleration of corrosion, the performance of fiber Bragg grating-based sensor systems attached to high-tensile steel reinforcement bars (ldquorebarsrdquo), and cast into concrete blocks was determined, and the results compared with those from conventional strain gauges where appropriate. The results show the benefits in the use of optical fiber networks under these circumstances and their ability to deliver data when conventional sensors failed.

Chemical etching of optical fibre tips - experiment and model

The formation of chemically etched fibre tips for use in optical scanning probe microscopy is addressed. For tips formed at a cleaved fibre end in the bulk of a buffered HF acid solution the morphological features (tip height, cone angle) are found to depend strongly on the temperature and etchant composition. The tip formation process is analysed and explained in terms of a simple model in which the only pertinent physical parameters are the fibre core diameter and etch rates of the fibre core and cladding. The etch rates are determined in separate experiments as a function of temperature (in the range 24-50 degreesC) for etchant solutions of de ionised water: 50% HF acid: 40% NH4F in the volume ratio 1 : 1 : X for X=2, 4 and 6, and used in the model to yield a correct description of the experimental tip cone angles. The model is successfully extended to the intriguing case of negative tip formation which initiates in a normal, positive tip structure. By contrast, tip formation in the meniscus region of a bare fibre/etchant/organic solvent system is found to be independent of etchant composition and temperature. (C) 2000 Elsevier Science B.V. All rights reserved.

Thermoforming carbon fibre-reinforced thermoplastic composites

The use of carbon fibre composites is growing in many sectors but their use remains stronger in very high value industries such as aerospace where the demands of the application more easily justify the high energy input needed and the corresponding costs incurred. This energy and cost input is returned through gains over the whole life of the product, with for example, longer maintenance intervals for an aircraft and lower fuel burn. Thermoplastic composites however have a different energy and cost profile compared to traditional thermosets with notable differences in recyclability, but this profile is not well quantified or documented. This study considers the key process control parameters and identifies an optimal window for processing, along with the effect this has on the final characteristics of the manufactured parts. Interactions between parameters and corresponding sensitivities are extracted from the results.