Studies on adhesives for bonding rubber to rubber and rubber to textiles

The primary objective of this investigation has been to develop more efficient and low cost adhesives for bonding various elastomer combinations particularly NR to NR, NR/PB to NR/PB, CR to CR,NR to CR and NR to NBR.A significant achievement of the investigation was the development of solventless and environment friendly solid adhesives for NR to NR and NR/PB to NR/PB particularly for precured retreading. Conventionally used adhesives in this area are mostly NR based adhesive strips in the presence of a dough. The study has shown that an ultra accelerator could be added to the dough just before applying it on the tire which can significantly bring down the retreading time resulting in prolonged tire service and lower energy consumption. Further latex reclaim has been used for the preparation of the solid strip which can reduce the cost considerably.Another significant finding was that by making proper selection of the RF resin, the efficiency and shelflife of the RFL adhesive used for nylon and rayon tire cord dipping can be improved. In the conventionally used RFL adhesive, the resin once prepared has to be added to the latex within 30 minutes and the RFL has to be used after 4 hours maturation time maximum shelf life of the RFL dip solution being 72 hours. In this study a formaldehyde deficient resin was used and hence more flexibility was available for mixing with latex and maturing. It also has a much longer shelf life. In the method suggested in this study, formaldehyde donors were added only in the rubber compound to make up the formaldehyde deficiency in the RFL. The results of this investigation show that the pull through load by employing this method and the conventional method are comparable. This study has also shown that the amount of RF resin with RFL adhesive can be partially replaced by other modifying agents for cost reduction.Cashew nut shell liquid (CNSL) resin can be employed for improving the bonding of dipped nylon and rayon cord with NR.Since CNSL resin cannot be added in the dip solution since it is not soluble in water, it was added in the rubber compound. The amount of wood rosin in the rubber compound can be reduced by using CNSL resin.Another interesting result of the investigation was the use of CR based adhesive modified with chlorinated natural rubber for CR to CR bonding. Addition of chlorinated natural rubber was found to improve sea water resistance of CR based adhesive. In the bonding of a polar rubber like nitrile rubber or polychloroprene rubber to a non polar rubber like natural rubber, an adhesive based on polychloroprene rubber was found to be effective.

Studies on Thermoplastic Elastomers Based on Polyethylene/Elastomer Blends

Department of Polymer Science and Rubber Technology, Cochin University of Science and Technology.

Rubber-Layered Clay Nanocomposites

Department of Polymer Science and Rubber Technology,Cochin University of Science and Technology

Studies on in situ precipitated silica filled rubber composites with special reference to NR, NBR and SBR

Precipitated silica is the most promising alternative for carbon black in tyre tread compounds due to its improved performance in terms of rolling resistance and wet grip.But its poor processability is a serious limitation to its commercial application.This thesis suggests a novel route for the incorporation of silica in rubbers,i.e.,precipitation of silica in rubber latex followed by coagulation of the latex to get rubber-silica maseterbatch.Composites with in situ precipitated silica showed improved processability and mechanical properties,when compared to conventional silica composites.

Molecular Biological investigations on viral diseases affecting farmed penaeid shrimps in Kerala

This thesis covers various aspects of viral diseases affecting shrimp aquaculture. The research component of this thesis can be divided into four areas. The areas covered are: I) A study to determine the prevalence of WSSV among the crustaceans in the Vembanad estuary, the shrimp aquaculture farms surrounding the estuary, and the sea off Cochin coast, India using two , sets of nested PCR primers. 2) An investigation to compare the sequence of six major structural proteins of WSSV; vp28, vp26, vp 19, vp68, vp281, vp466 from different geographical locations with that of an isolate from India. 3) Simultaneous occurrence of HPV, IHHNV, MBV and WSSV in postlarvae of P. monodon from hatcheries in India was monitored by Polymerase Chain Reaction. 4) A real time PCR procedure was developed for the quantitative analysis of WSSV infection. The viral load of postlarvae from hatcheries in Kerala meant for aquaculture was also determined using the quantitative PCR.

Studies on the isolation and characterization of flavones and triterpenoids from a few plants

In the present scenario, there is an increasing demand for natural products in food industry, pharmaceuticals, cosmetics and agricultural sectors. In this context phytochemical study to identify newer chemicals has got great relevance. Phytochemical studies have become more reliable and encouraging with the development of modern analytical techniques.In the present work the leaves of Piper colubrinum (Piperaceae), aerial parts of Mussaenda fiondosa (Rubiaceae) and Humboldtia vahliana (Leguminosae) and the pericarp of fruits of Artocarpus heterophyllus (Moraceae) were investigated for their secondary metabolites. The major compounds isolated belong to the groups of flavonoids and triterpenoids.Naturally occurring flavonoids have been used widely in chemotaxonomic studies of plants. Flavones and flavonols constitute a group of biosynthetically related natural products. No universal function has been established for flavones and flavonols in plants. However, many functions in individual plants have been demonstrated. These include protection of plants from ultraviolet light, insects and pests; pollinator attractants; antioxidants; plant hormone controllers; enzyme inhibitors and allelopathic agents. Flavonoids are attracting the attention of medical scientists in recent years because of their anticarcinogenic, antiallergic and antiinflammatory properties. The recent discovery that flavonoids are involved in the process of nitrogen fixation in plants also opens the way for agricultural application of these constituents.Triterpenoids are another class of compounds that are ubiquitous in plants. Some triterpenoids present in the latex and resins of plants are believed to be involved in chemical defence against pathogens and herbivores. Triterpenoids possess various biological properties including anti-inflammatory, antifeedant, pesticidal, fungitoxic and antimicrobial activities. Triterpenoids with cytotoxic activity and inhibitory effect on seed germination are also known.

Short Nylon-6 Fibre/Rubber-Toughened Polystyrene Composites

The thesis describes studies on development of short Nylon-6 fibre composites based on rubber-toughened polystyrene (PS). Toughening was done using natural rubber (NR), styrene-butadiene rubber (SBR) and whole tyre reclaim (WTR). The composites were prepared by melt mixing in an internal mixer at 170 oC. It was found that the optimum blend ratio was 85/15 for PS/NR, 90/10 for PS/SBR and 90/22 for PS/WTR blends. The effect of dynamic vulcanisation on 85/15 PS/NR and 90/10 PS/SBR blends using dicumyl peroxide (DCP) at various concentrations were also studied. The dynamic crosslinking improved the tensile properties, flexural properties, impact strength and dynamic mechanical properties of both the blends. The effect of unmodified and resorcinol formaldehyde latex (RFL)-coated short Nylon-6 fibres on the mechanical properties, morphology and dynamic mechanical properties of 85/15 PS/NR, 90/10 PS/SBR and 90/22 PS/WTR blends were studied. Fibre loading was varied from 0 to 3 wt.%. For 85/15 PS/NR blend, there was a significant enhancement in tensile properties, flexural properties and impact strength with 1 wt.% of both unmodified and RFL-coated fibres. Dynamic mechanical analysis revealed that the storage modulus at room temperature was maximum at 1 wt.% fiber loading for both composites. The surface functionality of the fiber was improved by giving alkali treatment. Maleic anhydride-grafted-polystyrene (MA-g-PS) was prepared and used as a compatibiliser. The effect of MA-g-PS on the composites was investigated with respect to mechanical properties, morphology and dynamic mechanical properties. The compatibiliser loading was varied from 0 to 2 wt.%. The properties were enhanced significantly in the case of treated and untreated fibre composites at a compatibiliser loading of 0.75 wt.%. SEM analysis confirmed better bonding between the fibre and the matrix. Dynamic mechanical studies showed that the storage modulus at room temperature improved for treated fibre composites in the presence of compatibiliser. In the case of 90/10 PS/SBR composites, the addition of short Nylon-6 fibres at 1 wt.% loading improved the tensile modulus, flexural properties and impact strength while the tensile strength was marginally reduced. The surface treated fibers along with compatibiliser at 0.5 wt.% improved the tensile properties, flexural properties and impact strength. DMA reveale that the storage modulus at room temperature was better for composites containing untreated fibre and the compatibiliser. In the case of 90/22 PS/WTR blends, 1 wt.% unmodified fibre and 0.5 wt.% RFL-coated fibres improved tensile modulus, flexural properties and impact strength. Tensile strength was improved marginally. The surface treatment of Nylon fibre and the addition of compatibiliser at 0.5 wt.% enhanced the tensile properties, flexural properties and impact strength. The dynamic mechanical analysis showed that the storage modulus at room temperature was better for untreated fibre composites in conjunction with the compatibiliser. The thermal stability of PS/NR was studied by TGA. Thermal stability of the blends improved with dynamic vulcanisation and with the incorporation of RFL-coated Nylon fibres. The untreated and partially hydrolyzed fibre composites in conjunction with the compatibiliser enhanced the thermal stability. Kinetic studies showed that the degradation of the blends and the composites followed first order kinetics.

Development of Novel Polymer based Adhesives

Novel latex based and solution based adhesives were prepared and evaluated for wood to wood bonding.These adhesive were found to be superior to commercical adhesives like fevicol and dentrite.Novel adhesives were prepared for leather to leather bonding and these were also found to be more efficientt than the polyurethane type and dentrite adhesives used commercially.A novel strip adhesive system employing very low amount of solvents was tried successfully for rubber-to-metal bonding.Further ,a novel adhesive system was investigated successfully for bonding copper coated bead wire and steel cord to rubber by modifying it with chloroprene rubber.

Study on acceleratore in rubber vulcanization with special reference to the binary systems containing substituted dithiobiurets

The thesis entitled Study on Accelerators in Rubber Vulcanization with Special Reference to the Binary Systems Containing Substituted Dithiobiurets. It includes a detailed study on the binary accelerator systems containing substituted dithiobiurets in natural rubber and NR latex and dithiobiurets in SBR and NR-SBR blends vulcanization systems. It deals with the experimental procedure adopted for the preparation of DTB-II and DTB-III; the procedure for compounding and vulcanization and determination of physical properties like modulus, tensile strength, elongation at break, hardness, compression set, heat build up etc. The results indicate that there is efficient acceleration activity of the dithiobiurets in the vulcanization of natural rubber latex containing TMT. The study of dithiobiurets in natural rubber and NR latex reveal that they are having definite accelerating effect in SBR vulcanization systems.

Development of energy saving forms of natural rubber

Although the physical and technological properties of modified rubbers were compared with those of conventional rubbers in the earlier studies reviewed above, the extent of energy saving possible by their use has not been quantified. In the present work it is proposed to determine the energy saving possible by using the following forms of natural rubber: 1. Oil extended natural rubber, 2. peptised natural rubber, 3. latex stage compounds. The process of production and quality control of the above types of processed rubbers are proposed to be standardised. It is also planned to work out a methodology for utilising field coagula for production of constant viscosity rubbers. The variation in processing properties of rubber from popular Indian clones will be examined and those with energy advantages in the processing stage will be identified. In conclusion a recommendation for adoption of a commercially advantageous processing procedure among Indian rubber plantation industry is also given.

Studies on a New Vulcanization Syste

Studies on the chemistry of vulcanization” play a central role in the efforts to achieve better product performance from natural and synthetic rubbers. They provide rubber technologists with an increasingly realistic picture of molecular framework of vulcanizates, from which relation between physical properties and chemical constitution may be deduced. Moreover, these studies are also aimed at the understanding of the vulcanization process, in sufficiently advanced chemical mechanistic terms, so that the effect of changes on vulcanizate structure can rationally be predicted.“ The study of accelerator activity ofthe binary system containing ATU with TMTD, and with MBTS in sulphur vulcanization of dry natural rubber using standard procedures for compounding and vulcanization is described in the third chapter. The study of the gum vulcanizates form part I of this chapter The behaviour of the experimental mixes were compared with those of the controls containing thiourea; diphenyl guanidine

Studies on the treatment of effluents from natural rubber processing units

The present study was undertaken to evaluate the effectiveness of a few physico-chemical and biological methods for the treatment of effluents from natural rubber processing units. The overall objective of this study is to evaluate the effectiveness of certain physico-chemical and biological methods for the treatment of effluents from natural rubber processing units. survey of the chemical characteristics of the effluents discharged from rubber processing units showed that the effluents from latex concentration units were the most polluting

Molecular breakdown of different forms of natural rubber and its influence on properties of their mixes and vulcanizates

The forms of natural rubber studied were sheet [RSS 4 and RSS 5], ISNR 20 and EBC. In the case of the latter two forms samples from estate and nonestate sectors were included. The samples were collected from different locations at specified intervals, for a particular period. The effect of the extent of mastication on raw rubber properties as well as the properties of the compounds and vulcanizates also studied. The consistency in raw rubber properties and breakdown behavior of skim rubber were studied by collecting samples periodically from selected processing units. The effect of incorporation of skim with ISNR 20 has also been investigated

New accelerator system for low temperature curing of elastomers with special reference to NR, NBR and NR/BR blends

The primary objective of this work is to develop an efficient accelerator system for low temperature vulcanization of rubbers. Although xanthates are known to act as accelerators for low temperature vulcanization, a systematic study on the mechanism of vulcanization, the mechanical properties of the vulcanizates at varying temperatures of vulcanization, cure characteristics etc are not reported. Further. xanthate based curing systems are not commonly used because of their chance for premature vulcanization during processing. The proposed study is to develop a novel accelerator system for the low temperature vulcanization of rubbers having enough processing safely. lt is also proposed to develop a method for the prevulcanisation of natural rubber latex at room temperature. As already mentioned the manufacture of rubber products at low temperature will improve its quality and appearance. Also, energy consumption can be reduced by low temperature vulcanization. in addition, low temperature vulcanization will be extremely useful in the area of repair of defective products, since subjecting finished products to high temperatures during the process of repair will adversely affect the quality of the product. Further. room temperature curing accelerator systems will find extensive applications in surface coating industries.

Amidino Thiourea as a Secondary Accelerator in Rubber Vulcanization

Earlier studies5773 in our laboratory showed that when a nucleophile is used along with disulphide or sulphenamide accelerators the vulcanization is accelerated greatly and the reaction mechanism is generally nucleophilic in nature. However it was observed that it also changes with the systems under review. The present study, deals with the use of unsubstituted amidino thiourea i.e. aminoimino methyl thiourea(AMT) V in the vulcanization studies of different elastorners and their blends. One of the aims of this study was to get further proof with regard to the theory of nucleophilic reaction mechanism in such binary systems.Mixes containing thiourea are used as controls. AMT is more nucleophilic than TU and this is clear from the fact that the fonner can condense with isothiocynate even in the absence of alkali while TU cannot". Also the guanidinyl group in AMT can facilitate the polarization of the C=S bond favouring a nucleophilic reaction