Novel high-power-factor isolated electronic ballast for multiple tubular fluorescent lamps

This paper presents a novel isolated electronic ballast for multiple fluorescent lamps, featuring high power-factor, and high efficiency. Two stages compose this new electronic ballast, namely, a new voltage step-down isolated Sepic rectifier, and a classical resonant Half-Bridge inverter. The new isolated Sepic rectifier is obtained from a Zero-Current-Switching (ZCS) Pulse-Width-Modulated (PWM) soft-commutation cell. The average-current control technique is used in this preregulator stage in order to provide low phase displacement and low Total-Harmonic-Distortion (THD) at input current, resulting in high power-factor, and attending properly IEC 61000-3-2 standards. The resonant Half-Bridge inverter performs Zero-Voltage-Switching (ZVS), providing conditions for the obtaining of overall high efficiency. It is developed a design example for the new isolated electronic ballast rated at 200W output power, 220Vrms input voltage, 115Vdc dc link voltage, with rectifier and inverter stages operating at 50kHz. Finally, experimental results are presented in order to verify the developed analysis. The THD at input current is equal to 5.25%, for an input voltage THD equal to 1.63%, and the measured overall efficiency is about 88.25%, at rated load.

Nutrients foliar content for high productivity cultivars of guava in Brazil

Commonly grown in tropical and sub-tropical regions, guava (Psidium guajava L.) is an important fruit crop of Brazil. It is cultivated on a large scale in São Paulo state, and covers about 6,500 hectares. As a result of the guava selection program developed at FCAV/UNESP, two new cultivars were created: 'Rica' and 'Paluma' with a high productivity, and also with higher nutritional requirement. Leaves analysis has become a powerful tool in mineral-nutrition research with fruit crops, not only to determine response to different nutrients, but also for diagnostic techniques in making fertilizer recommendations and assessing deficiency symptoms. Nutrient composition of the leaves varies depending on the leaf maturity, tree age, variety and nutrient supply. For the interpretation of analytical values, selection of the index tissue is important. The results of experiments conducted in the field during 1989-2000 were studied. The nutritional status was evaluated by annual leaf sampling, carried out at full bloom. Recent fully developed leaves, corresponding to the third pair (with the petiole) were collected, starting at the end of the branch, all around the tree, at a height of 1.5 m from the soil, with a total of 30 leaf pairs per sample. The yield was evaluated by weighing all the fruits in the useful area of each lot. Foliar chemical analysis showed excellent correlation with the fruit production. Through the results it was verified that the maximum yield was associated to the following levels: N = 22-26; P = 1.5-1.9; K = 17-20; Ca = 11-15; Mg = 2.5-3.5; S = 3.0-3.5 g kg -1; B = 20-25; Cu = 10-40; Fe = 50-150; Mn = 180-250; Zn = 25-35 mg kg-1 DW in the leaves of the 'Rica' guava and to N = 20-23; P = 1.4-1.8; K = 14-17; Ca = 7-11; Mg = 3.4-4.0; S = 2.5-3.5 g kg-1; B = 20-25; Cu = 20-40; Fe = 60-90; Mn = 40-80; Zn = 25-35 mg kg-1 DW in the leaves of the 'Paluma' guava.

Yield and quality of net melon cultivated in sand in the greenhouse

The behavior of two hybrids of muskmelon ('Bônus no 2' and 'Don Carlos') in relation to the productivity and quality of its fruits, making use of fertigation in sand substrate in protected environment, was studied. Amianthus cement structures of the Canalete runlet type were used to keep the plants 0.30m from each other and 1.0m between lines. 'Don Carlos' hybrid had fruit mean weight, longitudinal and transversal diameter, pulp mean thickness, and total acidity substantially superior in relation to 'Bônus no 2'. Considering the total soluble solid content, 'Bônus no 2' had better results. However, there was no significant difference in fruits/plant or pulp thickness between the two hybrids.

Total and harvest-date yield of processing tomato cultivars

The productivity of 28 tomato cultivars was evaluated over three stages of harvest. The study was carried out during from June to December of 1999 in an open field at the experimental area of the Section of Olericulture and Aromatic Medicinal Plants, Department of Crop Production at FCAV-UNESP, Jaboticabal, SP, Brazil. The cultivars studied were H 7155, Hypeel, Andino, U 573, H 9036, IPA 6, H 9494, AG 33, Yuba, RPT 1294, AG 72, Pelmeech, Curico, Hypeel 45, RPT 1478, H 9492, H 9498, H 2710, Hitech 45, Halley, Botu 13, H 9553, U 646, NK 1570, AG 45, RPT 1095, RPT 1570, and PSX 37511. The experimental design was a randomized block design with four repetitions, with five plants per plot. Productivity was evaluated at three stages of harvest at 119, 149 and 179 days after seeding. There were no significant differences among the cultivars at the first harvest (119 days). The majority of the cultivars produced their highest yield at the second harvest; the most productive cultivars were Curicó and AG 72, which yielded 4.69 and 4.67 kg/plant, respectively, although they did not differ statistically from the cultivars Hypeel 45 (4.35 kg/plant) and H 9498 (4.16 kg/plant). Yields of the cultivars Andino and H 9494 were evenly distributed between the second and third harvests. At the third harvest, cultivar IPA 6 had the highest yield (2.9 kg/plant) and was statistically different from all other cultivars except H 9036 (2.34 kg). These two cultivars had the most delayed and concentrated maturity, making them suitable for mechanical harvesting, although at a later time. Cultivar AG 72 had the greatest total yield (5.76 kg/plant), but it was not statistically different from cultivars Hypeel 45 (5.43 kg), Curico (4.17 kg), H 9498 (4.83 kg), H 7155 (4.58 kg) and Halley (4.55 kg). All of the cultivars, with the exception of cultivars H 9036, IPA 6, Andino and H 9494 showed in the second harvest concentrated maturity, making it suitable for mechanical harvesting.

Dimmable electronic ballast with high power-factor SEPIC preregulator, for multiple tubular fluorescent lamps

An electronic ballast for multiple tubular fluorescent lamps is presented in this paper. The proposed structure features high power-factor, dimming capability, and soft-switching to the semiconductor devices operated in high frequencies. A Zero-Current-Switching - Pulse-Width-Modulated (ZCS-PWM) SEPIC converter composes the rectifying stage, controlled by the instantaneous average input current technique, performing soft-commutations and high input power factor. Regarding the inverting stage, it is composed by a classical resonant Half-Bridge converter, associated to Series Parallel-Loaded Resonant (SPLR) filters. The dimming control technique employed in this Half-Bridge inverter is based on the phase-shift in the current processed through the sets of filter + lamp. In addition, experimental results are shown in order to validate the developed analysis.

An AC voltage regulator with high-power-factor, and control using a FPGA device

This paper presents the analysis, design, simulation, and experimental results for a high frequency high Power-Factor (PF) AC (Alternate Current) voltage regulator, using a Sepic converter as power stage. The control technique employed to impose a sinusoidal input current waveform, with low Total Harmonic Distortion (THD), is the sinusoidal variable hysteresis control. The control technique was implemented in a FPGA (Field Programmable Gate Array) device, using a Hardware Description Language (VHDL). Through the use of the proposed control technique, the AC voltage regulator performs active power-factor correction, and low THD in the input current, for linear and non-linear loads, satisfying the requirements of the EEC61000-3-2 standards. Experimental results from an example prototype, designed for 300W of nominal output power, 50kHz (switching frequency), and 127Vrms of nominal input and output voltages, are presented in order to validate the proposed AC regulator. © 2005 IEEE.

Productivity of cherry tomatoes under protected cultivation carried out with different types of pruning and spacing

The aim of the study was to evaluate production and determine the level of total soluble solids for cherry tomatoes, under protected cultivation carried out with different types of spacing and pruning. The experiment was performed according to a randomized block design in a 2×2 factorial scheme, with two types of spacing between plants and two types of pruning, and with five repetitions. The cultivar 'Sindy' (De Ruiter) was utilized. Each experimental parcel contained seven plants, and fruits were collected from the five central plants. The seedlings were produced in Styrofoam trays of 128 cells and transplanted at 33 days after planting using two types of spacing between plants (0.3 and 0.5 m) and 1 m spacing between rows. The plants were grown as single-or double-stem form and staked individually. The parameters evaluated were the number of fruit per plant, fresh weight of fruit and the level of total soluble solids expressed in °Brix. There was no evidence of significant interaction between the treatments. For fresh weight of fruit per plant, there was a significant effect when the plants were grown with a spacing of 1 × 0.5 m, with 4.12 kg per plant, compared to a production of 3.00 kg per plant with a spacing of 1 × 0.3 m. With regard to the number of fruit per plant, a significant difference was seen between the two types of spacing, where a spacing of 1 × 0.3 m yielded a lower number of fruit per plant (188.8), compared to that observed with a spacing of 1 × 0.5 m (238.1). With regard to the two types of pruning, there was a significant effect for only the number of fruit per plant, where the mean number of fruit was 188.4 with one stem and 238.4 with two stems. No significant difference was observed between the treatments for the level of total soluble solids. It is concluded that for the cultivar 'Sindy', under protected cultivation, production is better with a spacing of 0.5 m between plants and the use of two stems per plant.

A statistical analysis of loss factor to determine the energy losses

Given that the total amount of losses in a distribution system is known, with a reliable methodology for the technical loss calculation, the non-technical losses can be obtained by subtraction. A usual method of calculation technical losses in the electric utilities uses two important factors: load factor and the loss factor. The load factor is usually obtained with energy and demand measurements, whereas, to compute the loss factor it is necessary the learning of demand and energy loss, which are not, in general, prone of direct measurements. In this work, a statistical analysis of this relationship using the curves of a sampling of consumers in a specific company is presented. These curves will be summarized in different bands of coefficient k. Then, it will be possible determine where each group of consumer has its major concentration of points. ©2008 IEEE.

Structural change and productivity growth, 20 years later: old problems, new opportunities

Includes bibliography

Leaf spray fertilization of boron and zinc on productivity and fruit quality of Japanese pear tree

The cultivation of fruit plants from temperate climate in tropical or subtropical regions can be a good income alternative for the producer. However, due to the little existent information about cultivation of those fruit plants, the producers use imported techniques of other producing areas, or even an association of practices used for other fruit plants, pointing out the leaf spray fertilization of micronutrients without appropriate scientific base. In this context, the objective of this study was to verify the effect of the leaf spray fertilization of B and Zn on productivity and fruit quality of Japanese pear tree. The experiment was conducted from 2004 to 2005, in Ilha Solteira, in northwestern São Paulo State-Brazil. The climate is, according to the Köpppen Classification, tropical wet and dry (Aw). The 'Okusankichi' cultivar, grafted on Pyrus communis L. rootstock was used as well as doses of 110 g.ha-1 of B and 250 g.ha-1 of Zn in each application. The treatments were: T1. water, T2. boric acid, T3. zinc sulfate, T4. T2 + T3, T5. boric acid + urea + citric acid + EDTA, T6. zinc sulfate + urea + citric acid + EDTA, T7. T5 + T6, T8. boric acid + urea + citric acid + EDTA + sodium molibdate + sulfur + calcium chloride, T9. zinc sulfate + urea + citric acid + EDTA + Fe sulfate + Mn sulfate + Mg sulfate and, T10. T8+T9. A randomized blocks design was used and the averages were compared by Tukey test. In the first crop the mixture of boric acid with quelating agents were efficient to supply B to the plants and zinc sulfate plus quelating agents were efficient to increase Zn leaf content. However, the productivity and the fruit quality were not influenced by the leaf spray of B and Zn. In the second crop the leaf content of B and Zn and the productivity were not influenced by the leaf spray; the boric acid and the zinc sulfate with or without quelating agents increased the contents of total soluble solids and, the boric acid with or without quelating agents increased the contents of total titratable acidity.

Contribution of energy services to the Millennium Development Goals and to poverty alleviation in Latin America and the Caribbean: executive summary

Includes bibliography

Contribution of energy services to the millennium development goals and to poverty alleviation in Latin America and the Caribbean

Includes bibliography

Economic growth and performance in Latin America

Includes bibliography

Quality management promotion to improve competitiveness

Includes bibliography

Principal components and factor analytic models for birth to mature weights in Nellore cattle

A total of 61,528 weight records from 22,246 Nellore animals born between 1984 and 2002 were used to compare different multiple-trait analysis methods for birth to mature weights. The following models were used: standard multivarite model (MV), five reduced-rank models fitting the first 1, 2, 3, 4 and 5 genetic principal components, and five models using factor analysis with 1, 2, 3, 4 and 5 factors. Direct additive genetic random effects and residual effects were included in all models. In addition, maternal genetic and maternal permanent environmental effects were included as random effects for birth and weaning weight. The models included contemporary group as fixed effect and age of animal at recording (except for birth weight) and age of dam at calving as linear and quadratic effects (for birth weight and weaning weight). The maternal genetic, maternal permanent environmental and residual (co)variance matrices were assumed to be full rank. According to model selection criteria, the model fitting the three first principal components (PC3) provided the best fit, without the need for factor analysis models. Similar estimates of phenotypic, direct additive and maternal genetic, maternal permanent environmental and residual (co)variances were obtained with models MV and PC3. Direct heritability ranged from 0.21 (birth weight) to 0.45 (weight at 6 years of age). The genetic and phenotypic correlations obtained with model PC3 were slightly higher than those estimated with model MV. In general, the reduced-rank model substantially decreased the number of parameters in the analyses without reducing the goodness-of-fit. © 2013 Elsevier B.V.