Oxygen and hydrogen isotopes measured in the Northeast Atlantic

Only a few studies have examined the variation of oxygen and hydrogen isotopes of seawater in NE Atlantic water masses, and data are especially sparse for intermediate and deep-water masses. The current study greatly expands this record with 527 d18O values from 47 stations located throughout the mid- to low-latitude NE Atlantic. In addition, dD was analyzed in the 192 samples collected along the GEOTRACES North Atlantic Transect GA03 (GA03_e=KN199-4) and the 115 Iberia-Forams cruise samples from the western and southern Iberian margin. An intercomparison study between the two stable isotope measurement techniques (cavity ring-down laser spectroscopy and magnetic-sector isotope ratio mass spectrometry) used to analyze GA03_e samples reveals relatively good agreement for both hydrogen and oxygen isotope ratios. The surface (0-100 m) and central (100-500 m) water isotope data show the typical, evaporation related trend of increasing values equatorward with the exception for the zonal transect off Cape Blanc, NW Africa. Off Cape Blanc, surface water isotope signatures are modified by the upwelling of fresher Antarctic Intermediate Water (AAIW) that generally has isotopic values of 0.0 to 0.5 per mil for d18O and 0 to 2 per mil for dD. Along the Iberian margin the Mediterranean Outflow Water (MOW) is clearly distinguished by its high d18O (0.5-1.1 per mil) and dD (3-6 per mil) values that can be traced into the open Atlantic. Isotopic values in the NE Atlantic Deep Water (NEADW) are relatively low (d18O: -0.1 to 0.5 per mil; dD: -1 to 4 per mil) and show a broader range than observed previously in the northern and southern convection areas. The NEADW is best observed at GA03_e Stations 5 and 7 in the central NE Atlantic basin. Antarctic Bottom Water isotope values are relatively high indicating modification of the original Antarctic source water along the flow path. The reconstructed d18O-salinity relationship for the complete data set has a slope of 0.51, i.e., slightly steeper than the 0.46 described previously by Pierre et al. (1994, J. Mar. Syst. 5 (2), 159-170.) for the tropical to subtropical Northeast Atlantic. This slope decreases to 0.46 for the subtropical North Atlantic Central Water (NACW) and the MOW and to 0.32 for the surface waters of the upper 50 m. The dD-salinity mixing lines have estimated slopes of 3.01 for the complete data, 1.26 for the MOW, 3.47 for the NACW, and 2.63 for the surface waters. The slopes of the d18O-dD relationship are significantly lower than the one for the Global Meteoric Water Line with 5.6 for the complete data set, 2.30 for the MOW, 4.79 for the NACW, and 3.99 for the surface waters. The lower slopes in all the relationships clearly reflect the impact of the evaporation surplus in the subtropics.

Responses of three tropical seagrass species to CO2 enrichment

Increased atmospheric carbon dioxide leads to ocean acidification and carbon dioxide (CO2) enrichment of seawater. Given the important ecological functions of seagrass meadows, understanding their responses to CO2 will be critical for the management of coastal ecosystems. This study examined the physiological responses of three tropical seagrasses to a range of seawater pCO2 levels in a laboratory. Cymodocea serrulata, Halodule uninervis and Thalassia hemprichii were exposed to four different pCO2 treatments (442-1204 µatm) for 2 weeks, approximating the range of end-of-century emission scenarios. Photosynthetic responses were quantified using optode-based oxygen flux measurements. Across all three species, net productivity and energetic surplus (PG:R) significantly increased with a rise in pCO2 (linear models, P < 0.05). Photosynthesis-irradiance curve-derived photosynthetic parameters-maximum photosynthetic rates (P max) and efficiency (alpha) also increased as pCO2 increased (linear models, P < 0.05). The response for productivity measures was similar across species, i.e. similar slopes in linear models. A decrease in compensation light requirement (Ec) with increasing pCO2 was evident in C. serrulata and H. uninervis, but not in T. hemprichii. Despite higher productivity with pCO2 enrichment, leaf growth rates in C. serrulata did not increase, while those in H. uninervis and T. hemprichii significantly increased with increasing pCO2 levels. While seagrasses can be carbon-limited and productivity can respond positively to CO2 enrichment, varying carbon allocation strategies amongst species suggest differential growth response between species. Thus, future increase in seawater CO2 concentration may lead to an overall increase in seagrass biomass and productivity, as well as community changes in seagrass meadows.

China's Impact on the Exports of Other Asian Countries: A Note

Despite widespread interest in China's growing trade surplus and its impact on other countries, empirical research in these issues is handicapped by the lack of reliable statistics on aggregate import and export prices. Although researchers estimate the trade volumes of China and other East Asian countries using a variety of surrogate price indices, an inappropriate deflator can give rise to a significant bias in econometric analysis. This paper discusses the potential seriousness of this problem by examining recent studies on the export competition between China and other Asian countries.

Food crop diversification as a risk mitigating strategy during conflict : evidence from Cote d'Ivoire

This study examines the significance of food crop diversification as a household risk mitigating strategy to achieve "self-sufficiency" to ensure food security during the civil conflict in Cote d’Ivoire. The main motivation for seeking self-sufficiency stems from the fact that during the period of heightened tension due to conflict, the north–south divide set by the UN peacekeeping line disrupted the agricultural supply chain from the food surplus zone, Savane in the north. While we theoretically predict a positive effect on crop diversification because of interrupted food supply chain, we also consider a negative effect due to the covariate shocks. We find robust and statistically significant empirical outcomes supporting such claims. The baseline outcomes withstand a series of robustness checks. The net effect of conflict on crop diversification is positive but not statistically significant. In addition, we find that increasing vulnerability to poverty and food insecurity during conflict seems to be the underlying factors that motivate farm households to adopt such coping strategies.

Land and labor reallocation in pre-modern Japan : a case of a northeastern village in 1720-1870

In agricultural societies, adjusting land and labor according to changes of labor endowment that result from family life cycle events is premised on making full use of resources for each farming household and for the economy as a whole. This paper examines how and how well households in pre-modern Japan reallocated land and labor, using a population register covering 150 years from 1720–1870 for a village in the Tohoku region. We find that households reacted to equalize their production factors; land-scarce households tended to acquire or rent-in land and out-migrate their kin members, while land-abundant households tended to release or rent-out land, in-migrate kin members, or employ non-kin members. Estimates suggest that more than 80% of the surplus or deficit area of land was resolved if the household rented or "sold" land. We discuss a potential underlying mechanism; namely, that the village's collective responsibility for tax payment (murauke) motivated both individual households and the village as a whole to reallocate land and labor for the efficient use of resources.

Energy efficiency standard and labeling program and consumer welfare : a case of the air conditioner market in China

Improving energy efficiency is an unarguable emergent issue in developing economies and an energy efficiency standard and labeling program is an ideal mechanism to achieve this target. However, there is concern regarding whether the consumers will choose the highly energy efficient appliances because of its high price in consequence of the high cost. This paper estimates how the consumer responds to introduction of the energy efficiency standard and labeling program in China. To quantify evaluation by consumers, we estimated their consumer surplus and the benefits of products based on the estimated parameters of demand function. We found the following points. First, evaluation of energy efficiency labeling by the consumer is not monotonically correlated with the number of grades. The highest efficiency label (Label 1) is not evaluated to be no less higher than labels 2 and 3, and is sometimes lower than the least energy efficient label (Label UI). This goes against the design of policy intervention. Second, several governmental policies affects in mixed directions: the subsidies for energy saving policies to the highest degree of the labels contribute to expanding consumer welfare as the program was designed. However, the replacement for new appliances policies decreased the welfare.

Desarrollo de un modelo de formación del valor inmobiliario en áreas de crecimiento suburbano. Aplicación a la comarca de la Vega Baja del Segura en el litoral alicantino

Una de las principales líneas de investigación de la economía urbana es el comportamiento del mercado inmobiliario y sus relaciones con la estructura territorial. Dentro de este contexto, la reflexión sobre el significado del valor urbano, y abordar su variabilidad, constituye un tema de especial importancia, dada la relevancia que ha supuesto y supone la actividad inmobiliaria en España. El presente estudio ha planteado como principal objetivo la identificación de aquellos factores, ligados a la localización que explican la formación del valor inmobiliario y justifican su variabilidad. Definir este proceso precisa de una evaluación a escala territorial estableciendo aquellos factores de carácter socioeconómico, medioambiental y urbanístico que estructuran el desarrollo urbano, condicionan la demanda de inmuebles y, por tanto, los procesos de formación de su valor. El análisis se centra en valores inmobiliarios residenciales localizados en áreas litorales donde la presión del sector turístico ha impulsado un amplio. Para ello, el ámbito territorial seleccionado como objeto de estudio se sitúa en la costa mediterránea española, al sur de la provincia de Alicante, la comarca de la Vega Baja del Segura. La zona, con una amplia diversidad ecológica y paisajística, ha mantenido históricamente una clara distinción entre espacio urbano y espacio rural. Esta dicotomía ha cambiado drásticamente en las últimas décadas, experimentándose un fuerte crecimiento demográfico y económico ligado a los sectores turístico e inmobiliario, aspectos que han tenido un claro reflejo en los valores inmobiliarios. Este desarrollo de la comarca es un claro ejemplo de la política expansionista de los mercados de suelo que ha tenido lugar en la costa española en las dos últimas décadas y que derivado en la regeneración de un amplio tejido suburbano. El conocimiento del marco territorial ha posibilitado realizar un análisis de variabilidad espacial mediante un tratamiento masivo de datos, así como un análisis econométrico que determina los factores que se valoran positivamente y negativamente por el potencial comprador. Estas relaciones permiten establecer diferentes estructuras matemáticas basadas en los modelos de precios hedónicos, que permiten identificar rasgos diferenciales en los ámbitos económico, social y espacial y su incidencia en el valor inmobiliario. También se ha sistematizado un proceso de valoración territorial a través del análisis del concepto de vulnerabilidad estructural, entendido como una situación de fragilidad debida a circunstancias tanto sociales como económicas, tanto actual como de tendencia en el futuro. Actualmente, esta estructura de demanda de segunda residencia y servicios ha mostrado su fragilidad y ha bloqueado el desarrollo económico de la zona al caer drásticamente la inversión en el sector inmobiliario por la crisis global de la deuda. El proceso se ha agravado al existir un tejido industrial marginal al que no se ha derivado inversiones importantes y un abandono progresivo de las explotaciones agropecuarias. El modelo turístico no sería en sí mismo la causa del bloqueo del desarrollo económico comarcal, sino la forma en que se ha implantado en la Costa Blanca, con un consumo del territorio basado en el corto plazo, poco respetuoso con aspectos paisajísticos y medioambientales, y sin una organización territorial global. Se observa cómo la vinculación entre índices de vulnerabilidad y valor inmobiliario no es especialmente significativa, lo que denota que las tendencias futuras de fragilidad no han sido incorporadas a la hora de establecer los precios de venta del producto inmobiliario analizado. El valor muestra una clara dependencia del sistema de asentamiento y conservación de las áreas medioambientales y un claro reconocimiento de tipologías propias del medio rural aunque vinculadas al sector turístico. En la actualidad, el continuo descenso de la demanda turística ha provocado una clara modificación en la estructura poblacional y económica. Al incorporar estas modificaciones a los modelos especificados podemos comprobar un verdadero desmoronamiento de los valores. Es posible que el remanente de vivienda construida actualmente vaya dirigido a un potencial comprador que se encuentra en retroceso y que se vincula a unos rasgos territoriales ya no existentes. Encontrar soluciones adaptables a la oferta existente, implica la viabilidad de renovación del sistema poblacional o modificaciones a nivel económico. La búsqueda de respuestas a estas cuestiones señala la necesidad de recanalizar el desarrollo, sin obviar la potencialidad del ámbito. SUMMARY One of the main lines of research regarding the urban economy focuses on the behavior of the real estate market and its relationship to territorial structure. Within this context, one of the most important themes involves considering the significance of urban property value and dealing with its variability, particularly given the significant role of the real estate market in Spain, both in the past and present. The main objective of this study is to identify those factors linked to location, which explain the formation of property values and justify their variability. Defining this process requires carrying out an evaluation on a territorial scale, establishing the socioeconomic, environmental and urban planning factors that constitute urban development and influence the demand for housing, thereby defining the processes by which their value is established. The analysis targets residential real estate values in coastal areas where pressure from the tourism industry has prompted large-scale transformations. Therefore, the focal point of this study is an area known as Vega Baja del Segura, which is located on the Spanish Mediterranean coast in southern Alicante (province). Characterized by its scenic and ecological diversity, this area has historically maintained a clear distinction between urban and rural spaces. This dichotomy has drastically changed in past decades due to the large increase in population attributed to the tourism and real estate markets – factors which have had a direct effect on property values. The development of this area provides a clear example of the expansionary policies which have affected the housing market on the coast of Spain during the past two decades, resulting in a large increase in suburban development. Understanding the territorial framework has made it possible to carry out a spatial variability analysis through massive data processing, as well as an econometric analysis that determines the factors that are evaluated positively and negatively by potential buyers. These relationships enable us to establish different mathematical systems based on hedonic pricing models that facilitate the identification of differential features in the economic, social and spatial spheres, and their impact on property values. Additionally, a process for land valuation was established through an analysis of the concept of structural vulnerability, which is understood to be a fragile situation resulting from either social or economic circumstances. Currently, this demand structure for second homes and services has demonstrated its fragility and has inhibited the area’s economic development as a result of the drastic fall in investment in the real estate market, due to the global debt crisis. This process has been worsened by the existence of a marginal industrial base into which no important investments have been channeled, combined with the progressive abandonment of agricultural and fishing operations. In and of itself, the tourism model did not inhibit the area’s economic development, rather it is the result of the manner in which it was implemented on the Costa Brava, with a land consumption based on the short-term, lacking respect for landscape and environmental aspects and without a comprehensive organization of the territory. It is clear that the link between vulnerability indexes and property values is not particularly significant, thereby indicating that future fragility trends have not been incorporated into the problem in terms of establishing the sale prices of the analyzed real estate product in question. Urban property values are clearly dependent on the system of development and environmental conservation, as well as on a clear recognition of the typologies that characterize rural areas, even those linked to the tourism industry. Today, the continued drop in tourism demand has provoked an obvious modification in the populational and economic structures. By incorporating these changes into the specified models, we can confirm a real collapse in values. It’s possible that the surplus of already-built homes is currently being marketed to a potential buyer who is in recession and linked to certain territorial characteristics that no longer exist. Finding solutions that can be adapted to the existing offer implies the viability of renewing the population system or carrying out modifications on an economic level. The search for answers to these questions suggests the need to reform the development model, without leaving out an area’s potentiality.

Potencial del cultivo de la chumbera (Opuntia ficus-indica (L) Miller) para la obtención de biocombustibles

El presente trabajo trata sobre el potencial del cultivo de chumbera (Opuntia ficus-indica (L) Miller) para la obtención de dos biocombustibles: bioetanol y biogás. Para lograr este objetivo se ha estudiado, por una parte, el empleo de procedimientos orientados a la producción de bioetanol no celulósico a partir de cladodios de chumbera, lo que ha dado como resultado rendimientos de entre 156 y 221 litros de etanol por cada tonelada de materia seca de biomasa, y, por otra, la obtención de biogás mediante la digestión anaeróbica de los mismos en régimen mesófilo, donde se han hallado rendimientos en torno a 198 m3 de metano por tonelada de materia seca. Una vez determinado el potencial de la materia prima se han diseñado procesos para una escala industrial que permitan la transformación de los cladodios de chumbera en ambos biocombustibles y se han determinado sus balances energéticos, los cuales han dado como resultado la autosuficiencia de ambos procesos, obteniéndose, además, un excedente térmico de 1.235 kcal L-1 de etanol producido, y en torno a 140 kep de energía total (térmica + eléctrica) por tonelada de materia seca empleada en la digestión anaeróbica. Por último se ha estimado el potencial de producción de ambos combustibles en un área apta para el cultivo de la chumbera. En concreto, este estudio se ha llevado a cabo para la provincia de Almería, elegida por tratarse de una zona con cierta tradición en el manejo de esta planta y presentar un clima semiárido mediterráneo. La superficie apta para el cultivo de la chumbera en esta provincia se ha estimado en 100.616 ha y el rendimiento medio del cultivo en 5 t MS ha-1 año-1. En el caso del bioetanol esto implicaría un potencial de producción en torno a 82.158 m3 año-1 que podrían dar lugar a la creación de dos macrodestilerías (con una producción de 100.000 L diarios) o de 49 microdestilerías (con 5.000 L diarios de producción). Si se optara por la transformación de la biomasa de chumbera en metano, podrían obtenerse 99,4 M de metros cúbicos, lo cual permitiría el establecimiento de 79 plantas de cogeneración de 500 kW cada una. ABSTRACT The present work deals with the potential of prickly pear (Opuntia ficus-indica (L) Mill.) biomass as a feedstock for bioethanol and biogas. In order to reach this objective different procedures aiming at the production of non-cellulosic bioethanol from cladodes were carried out; yields from156 to 221 litres of bioethanol per ton of dry matter were found. Mesophilic anaerobic digestion of cladodes was also studied and yields around 198 m3 of methane per ton of dry matter were reached. From these results, processes on an industrial scale were designed for both pathways of energy conversion of prickly-pear biomass and the respective energy balances were calculated. They resulted to be self-sufficient from an energetic point of view; the bioethanol pathway generated a thermal energy surplus of 1,235 kcal per litre of ethanol, while around 140 kep of total energy (heat + electricity) were obtained from the anaerobic digestion of one ton of dry cladodes. Finally, the potential production of both biofuels from prickly pear biomass was estimated for a specific area. The province of Almeria was chosen because of its climate conditions and the previous existence of prickly pear plantations. The area suitable for prickly pear cultivation in the province was estimated at a maximum of 100.616 ha, with an average yield of about 5 t DM ha-1 year-1. If prickly pear biomass were cropped for bioethanol in Almeria, the potential production of bioethanol could reach 82,158 m3 year-1, in either two macrodistilleries (100,000 L day-1) or 49 microdestilleries (5,000 L day-1). If the biogas pathway were preferred, 99. 4 Mm3 of methane could be reached and this would represent 79 CHP plants (500 kW each one).

Optimal and Long-Term Dynamic Transport Policy Design: Seeking Maximum Social Welfare through a Pricing Scheme.

This article presents an alternative approach to the decision-making process in transport strategy design. The study explores the possibility of integrating forecasting, assessment and optimization procedures in support of a decision-making process designed to reach the best achievable scenario through mobility policies. Long-term evaluation, as required by a dynamic system such as a city, is provided by a strategic Land-Use and Transport Interaction (LUTI) model. The social welfare achieved by implementing mobility LUTI model policies is measured through a cost-benefit analysis and maximized through an optimization process throughout the evaluation period. The method is tested by optimizing a pricing policy scheme in Madrid on a cordon toll in a context requiring system efficiency, social equity and environmental quality. The optimized scheme yields an appreciable increase in social surplus through a relatively low rate compared to other similar pricing toll schemes. The results highlight the different considerations regarding mobility impacts on the case study area, as well as the major contributors to social welfare surplus. This leads the authors to reconsider the cost-analysis approach, as defined in the study, as the best option for formulating sustainability measures.

User benefit assessment by a dynamic LUTI model for Madrid

Assessing users’ benefit in a transport policy implementation has been studied by many researchers using theoretical or empirical measures. However, few of them measure users’ benefit in a different way from the consumer surplus. Therefore, this paper aims to assess a new measure of user benefits by weighting consumer surplus in order to include equity assessment for different transport policies simulated in a dynamic middle-term LUTI model adapted to the case study of Madrid. Three different transport policies, including road pricing, parking charge and public transport improvement have been simulated through the Metropolitan Activity Relocation Simulator, MARS, the LUTI calibrated model for Madrid). A social welfare function (WF) is defined using a cost benefit analysis function that includes mainly costs and benefits of users and operators of the transport system. Particularly, the part of welfare function concerning the users, (i.e. consumer surplus), is modified by a compensating weight (CW) which represents the inverse of household income level. Based on the modified social welfare function, the effects on the measure of users benefits are estimated and compared with the old WF ́s results as well. The result of the analysis shows that road pricing leads a negative effect on the users benefits specially on the low income users. Actually, the road pricing and parking charge implementation results like a regressive policy especially at long term. Public transport improvement scenario brings more positive effects on low income user benefits. The integrated (road pricing and increasing public services) policy scenario is the one which receive the most user benefits. The results of this research could be a key issue to understanding the relationship between transport systems policies and user benefits distribution in a metropolitan context.

Morteros acumuladores con parafinas microencapsuladas para el aprovechamiento de la energía solar en suelos radiantes

Esta Tesis plantea la pregunta de si el uso de morteros con parafinas microencapsuladas combinado con colectores solares térmicos puede reducir el consumo de energías convencionales, en un sistema tradicional de suelo radiante. Se pretende contribuir al conocimiento acerca del efecto que produce en el edificio, el calor latente acumulado en suelos radiantes, utilizando morteros de cemento Portland con material de cambio de fase (PCM), en conjunto con la energía solar. Para cumplir con este propósito, la investigación se desarrolla considerando diversos aspectos. En primer lugar, se revisa y analiza la documentación disponible en la actualidad, de almacenamiento de energía mediante calor latente en la construcción, y en particular la aplicación de microcápsulas de PCM en morteros y suelos radiantes. También se revisa la documentación relacionada con la aplicación de la energía solar térmica y en suelo radiante. Se analiza la normativa vigente respecto al material, a los colectores solares y al suelo radiante. Se verifica que no hay normativa relacionada con mortero-PCM, debido a esto se aplica en la investigación una adaptación de la existente. La fase experimental desarrollada esta principalmente dirigida a la cuantificación, caracterización y evaluación de las propiedades físicas, mecánicas y térmicas del mortero de cemento Portland con parafinas microencapsuladas. Los resultados obtenidos y su análisis, permiten conocer el comportamiento de este tipo de morteros, con las diferentes variables aplicadas en la investigación. Además, permite disponer de la información necesaria, para crear una metodología para el diseño de morteros con parafina microencapsulada, tanto del punto de vista de su resistencia a la compresión y contenido de PCM, como de su comportamiento térmico como acumulador de calor. Esto se logra procesando la información obtenida y generando modelos matemáticos, para dosificar mezclas, y predecir la acumulación de calor en función de su composición. Se determinan los tipos y cantidades de PCM, y el cemento más adecuado. Se obtienen importantes conclusiones respecto a los aspectos constructivos a considerar en la aplicación de morteros con PCM, en suelo radiante. Se analiza y evalúa la demanda térmica que se puede cubrir con el suelo radiante, utilizando morteros con parafina microencapsulada, a través de la acumulación de energía solar producida por colectores solares, para condiciones climáticas, técnicas y tipologías constructivas específicas. Se determina que cuando los paneles cubren más de 60 % de la demanda por calefacción, se puede almacenar en los morteros con PCM, el excedente generado durante el día. Se puede cubrir la demanda de acumulación de energía con los morteros con PCM, en la mayoría de los casos analizados. Con esto, se determina que el uso de morteros con PCM, aporta a la eficiencia energética de los edificios, disminuyendo el consumo de energías convencionales, reemplazándola por energía solar térmica. En esta investigación, el énfasis está en las propiedades del material mortero de cemento-PCM y en poder generar metodologías que faciliten su uso. Se aborda el uso de la energía solar, para verificar que es posible su acumulación en morteros con PCM aplicados en suelo radiante, posibilitando el reemplazo de energías convencionales. Quedan algunos aspectos de la aplicación de energía solar a suelo radiante con morteros con PCM, que no han sido tratados con la profundidad que requieren, y que resultan interesantes de evaluar en este tipo de aplicaciones constructivas, como entre otros, los relacionados con la cuantificación de los ahorros de energía en las diferentes estaciones del año, de la estabilización de temperaturas internas, su análisis de costo y la optimización de este tipo de sistemas para utilización en verano, los que dan pie para otras Tesis o proyectos de investigación. ABSTRACT This Thesis proposes the question of whether the use of mortars with microencapsulated paraffin combined with solar thermal collectors can reduce conventional energy consumption in a traditional heating floor system. It aims to contribute to knowledge about the effect that it has on the building, the latent heat accumulated in heating floor, using Portland cement mortars with phase change material (PCM), in conjunction with solar energy. To fulfill this purpose, the research develops it considering various aspects. First, it reviews and analyzes the documentation available today, about energy storage by latent heat in the building, and in particular the application of PCM microcapsules in mortars and heating floors. It also reviews the documentation related to the application of solar thermal energy and heating floor. Additionally, it analyzes the current regulations regarding to material, solar collectors and heating floors. It verifies that there aren’t regulations related to PCM mortar, due to this, it applies an adaptation in the investigation. The experimental phase is aimed to the quantification, mainly, characterization and evaluation of physical, mechanical and thermal properties of Portland cement mortar with microencapsulated paraffin. The results and analysis, which allow us to know the behavior of this type of mortars with different variables applied in research. It also allows having the information necessary to create a methodology for designing mortars with microencapsulated paraffin, both from the standpoint of its resistance to compression and PCM content, and its thermal performance as a heat accumulator. This accomplishes by processing the information obtained, and generating mathematical models for dosing mixtures, and predicting heat accumulation depending on their composition. The research determines the kinds and amounts of PCM, and the most suitable cement. Relevant conclusions obtain it regarding constructive aspects to consider in the implementation of PCM mortars in heating floor. Also, it analyzes and evaluates the thermal demand that it can be covered in heating floor using microencapsulated paraffin mortars, through the accumulation of solar energy produced by solar collectors to weather conditions, technical and specific building typologies. It determines that if the panels cover more than 60% of the demand for heating, the surplus generated during the day can be stored in PCM mortars. It meets the demand of energy storage with PCM mortars, in most of the cases analyzed. With this, it determines that the use of PCM mortars contributes to building energy efficiency, reducing consumption of conventional energy, replacing it with solar thermal energy. In this research approaches the use of solar energy to determine that it’s possible to verify its accumulation in PCM mortars applied in heating floor, enabling the replacement of conventional energy. The emphasis is on material properties of PCM mortar and, in order to generate methodologies to facilitate their use. There are some aspects of solar energy application in PCM mortars in heating floor, which have not been discussed with the depth required, and that they are relevant to evaluate in this kind of construction applications, including among others: the applications related to the energy savings quantification in different seasons of the year, the stabilizing internal temperatures, its cost analysis and optimization of these systems for use in summer, which can give ideas for other thesis or research projects.

Farm nitrogen balances in six European landscapes as an indicator for nitrogen losses and basis for improved management.

Improved management of nitrogen (N) in agriculture is necessary to achieve a sustainable balance between the production of food and other biomass, and the unwanted effects of N on water pollution, greenhouse gas emissions, biodiversity deterioration and human health. To analyse farm N-losses and the complex interactions within farming systems, efficient methods for identifying emissions hotspots and evaluating mitigation measures are therefore needed. The present paper aims to fill this gap at the farm and landscape scales. Six agricultural landscapes in Poland (PL), the Netherlands (NL), France (FR), Italy (IT), Scotland (UK) and Denmark (DK) were studied, and a common method was developed for undertaking farm inventories and the derivation of farm N balances, N surpluses and for evaluating uncertainty for the 222 farms and 11 440 ha of farmland included in the study. In all landscapes, a large variation in the farm N surplus was found, and thereby a large potential for reductions. The highest average N surpluses were found in the most livestock-intensive landscapes of IT, FR, and NL; on average 202 ± 28, 179 ± 63 and 178 ± 20 kg N ha−1 yr−1, respectively. All landscapes showed hotspots, especially from livestock farms, including a special UK case with large-scale landless poultry farming. Overall, the average N surplus from the land-based UK farms dominated by extensive sheep and cattle grazing was only 31 ± 10 kg N ha−1 yr−1, but was similar to the N surplus of PL and DK (122 ± 20 and 146 ± 55 kg N ha−1 yr−1, respectively) when landless poultry farming was included. We found farm N balances to be a useful indicator for N losses and the potential for improving N management. Significant correlations to N surplus were found, both with ammonia air concentrations and nitrate concentrations in soils and groundwater, measured during the period of N management data collection in the landscapes from 2007–2009. This indicates that farm N surpluses may be used as an independent dataset for validation of measured and modelled N emissions in agricultural landscapes. No significant correlation was found with N measured in surface waters, probably because of spatial and temporal variations in groundwater buffering and biogeochemical reactions affecting N flows from farm to surface waters. A case study of the development in N surplus from the landscape in DK from 1998–2008 showed a 22% reduction related to measures targeted at N emissions from livestock farms. Based on the large differences in N surplus between average N management farms and the most modern and N-efficient farms, it was concluded that additional N-surplus reductions of 25–50%, as compared to the present level, were realistic in all landscapes. The implemented N-surplus method was thus effective for comparing and synthesizing results on farm N emissions and the potentials of mitigation options. It is recommended for use in combination with other methods for the assessment of landscape N emissions and farm N efficiency, including more detailed N source and N sink hotspot mapping, measurements and modelling.

Optimal and Long-Term Dynamic Transport Policy Design: Seeking Maximum Social Welfare through a Pricing Scheme

This article presents an alternative approach to the decision-making process in transport strategy design. The study explores the possibility of integrating forecasting, assessment and optimization procedures in support of a decision-making process designed to reach the best achievable scenario through mobility policies. Long-term evaluation, as required by a dynamic system such as a city, is provided by a strategic Land-Use and Transport Interaction (LUTI) model. The social welfare achieved by implementing mobility LUTI model policies is measured through a cost-benefit analysis and maximized through an optimization process throughout the evaluation period. The method is tested by optimizing a pricing policy scheme in Madrid on a cordon toll in a context requiring system efficiency, social equity and environmental quality. The optimized scheme yields an appreciable increase in social surplus through a relatively low rate compared to other similar pricing toll schemes. The results highlight the different considerations regarding mobility impacts on the case study area, as well as the major contributors to social welfare surplus. This leads the authors to reconsider the cost-analysis approach, as defined in the study, as the best option for formulating sustainability measures.

Evaluación de la tecnología CAES como sistema de almacenamiento de energía eólica. Caso de estudio en España

Se presenta a continuación un modelo de una planta del almacenamiento de energía mediante aire comprimido siguiendo un proceso adiabático. En esta planta la energía eólica sobrante se usa para comprimir aire mediante un tren de compresión de 25 MW, el aire comprimido será después almacenado en una caverna de sal a 770 metros de profundidad. La compresión se llevará a cabo por la noche, durante 6 horas, debido a los bajos precios de electricidad. Cuando los precios de la electricidad suben durante el día, el aire comprimido es extraído de la caverna de sal y es utilizado para producir energía en un tren de expansión de 70 MW durante 3 horas. La localización elegida para la planta es el norte de Burgos (Castilla y León, España), debido a la coincidencia de la existencia de muchos parques eólicos y una formación con las propiedades necesarias para el almacenamiento. El aspecto más importante de este proyecto es la utilización de un almacenamiento térmico que permitirá aprovechar el calor de la compresión para calentar el aire a la entrada de la expansión, eliminando combustibles fósiles del sistema. Por consiguiente, este proyecto es una atractiva solución en un posible futuro con emisiones de carbono restringidas, cuando la integración de energía renovable en la red eléctrica supone un reto importante. ABSTRACT: A model of an adiabatic compressed air energy storage plant is presented. In this plant surplus wind energy is used to compress air by means of a 25 MW compression train, the compressed air will be later stored in a salt cavern at 770 meters depth. Compression is carried out at night time, during 6 hours, because power prices are lower. When power prices go up during the day, the compressed air is withdrawn from the salt cavern and is used to produce energy in an expansion train of 70 MW during 3 hours. The chosen location for the plant is in the north of Burgos (Castilla y León, Spain), due to both the existence of several wind farms and a suitable storage facility with good properties at the same place. The relevance of this project is that it is provided with a thermal storage, which allows using the generated heat in the compression for re-heating the air before the expansion, eliminating fossil fuels from the system. Hence, this system is an attractive load balancing solution in a possibly carbon-constrained future, where the integration of renewable energy sources into the electric grid is a major challenge.

Elaboración de un nuevo modelo económico para la contribución al desarrollo sostenible de países del África subsahariana: implementación en Guinea Bissau

El escaso crecimiento de los países del África subsahariana, lleva a la necesidad de plantear un tipo de modelo económico que se adapte a sus especiales características y que en definitiva, conduzca a las sociedades que viven en estos países a un aumento de su calidad de vida, mediante mejoras en todos los campos sociales tales como: la enseñanza, la salud y la nutrición, que puedan ayudar a transformar las perspectivas del crecimiento económico, especialmente en los países objeto de estudio, que se caracterizan por presentar bajos ingresos y escaso desarrollo humano. Se puede concluir, por tanto, diciendo que en definitiva, el fin es el desarrollo humano y que el crecimiento económico es un medio. El propósito del crecimiento económico debe ser enriquecer la vida de la gente. Los adelantos a corto plazo en materia de desarrollo humano son posibles, merced a un mayor crecimiento económico que a su vez no debe desligarse del respeto por el medioambiente y el entorno. Para conseguir estos objetivos, se plantea en la presente tesis un modelo económico, elaborado siguiendo las directrices de la Dinámica de Sistemas, mediante el uso del programa informático VENSIM. El modelo planteado se basa en la producción de energía eléctrica, que sería capaz de abastecer a una población y generar unos excedentes que podrían ser vendidos y las ganancias reinvertidas para impulsar el crecimiento económico de la población a la que abastece. ABSTRACT Low growth in sub-Saharan Africa, leading to the need to establish a type of economic model that suits their special characteristics and ultimately lead to societies that live in these countries to increase human capacity through improvements in all social fields such as education, health and nutrition that can help transform the prospects for economic growth, especially in the countries under study, which are characterized by low income and low human development. It can be concluded, therefore, saying that ultimately, the end is human development and economic growth is a means. The purpose of economic growth should be to enrich the lives of people. The short-term advances in human development are possible, thanks to higher economic growth which in turn should not be separated from respect for the environment and intone. To achieve these objectives, we propose in this thesis an economic model, developed under the guidance of dynamic systems, using the computer program VENSIM. The proposed model is based on the production of electricity, which would be able to supply a population and generate a surplus that could be sold and the proceeds reinvested to boost economic growth in the population it serves.