Experimental validation of a fracture model for pearlitic steel bars based on the cohesive zone model

Steel is, together with concrete, the most widely used material in civil engineering works. Not only its high strength, but also its ductility is of special interest, since it allows for more energy to be stored before failure. A better understanding of the material behaviour before failure may lead to better structural safety strategies.

Polyolefin fiber-reinforced concrete enhanced with steel-hooked fibers in low proportions

Over the past few years, polyolefin fiber reinforced self-compacting concrete has shown high performance in both fresh and hardened state. Its fracture behavior for small deformations could be enhanced with a small amount of steel-hooked fibers, obtaining a hybrid fiber-reinforced concrete well suited for structural use. Four types of conventional fiber-reinforced concrete with steel and polyolefin fibers were produced on the basis of the same self-compacting concrete also manufactured as reference. These concrete mixtures were manufactured separately with the same fiber contents being subsequently used for two more hybrid mixtures. Fracture properties, in addition to fresh and mechanical properties, were assessed. The research showed both synergies (with the two types of fibers working together in the fracture processes) and an improvement of the orientation and distribution of the fibers on the fracture surface

Measurement of wide frequency range structural microvibrations with a pocket digital camera and sub-pixel techniques

Analysis of vibrations and displacements is a hot topic in structural engineering. Although there is a wide variety of methods for vibration analysis, direct measurement of displacements in the mid and high frequency range is not well solved and accurate devices tend to be very expensive. Low-cost systems can be achieved by applying adequate image processing algorithms. In this paper, we propose the use of a commercial pocket digital camera, which is able to register more than 420 frames per second (fps) at low resolution, for accurate measuring of small vibrations and displacements. The method is based on tracking elliptical targets with sub-pixel accuracy. Our proposal is demonstrated at a 10 m distance with a spatial resolution of 0.15 mm. A practical application over a simple structure is given, and the main parameters of an attenuated movement of a steel column after an impulsive impact are determined with a spatial accuracy of 4 µm.

Measurement of wide frequency range structural microvibrations with a pocket digital camera and sub-pixel techniques

Analysis of vibrations and displacements is a hot topic in structural engineering. Although there is a wide variety of methods for vibration analysis, direct measurement of displacements in the mid and high frequency range is not well solved and accurate devices tend to be very expensive. Low-cost systems can be achieved by applying adequate image processing algorithms. In this paper, we propose the use of a commercial pocket digital camera, which is able to register more than 420 frames per second (fps) at low resolution, for accurate measuring of small vibrations and displacements. The method is based on tracking elliptical targets with sub-pixel accuracy. Our proposal is demonstrated at a 10 m distance with a spatial resolution of 0.15 mm. A practical application over a simple structure is given, and the main parameters of an attenuated movement of a steel column after an impulsive impact are determined with a spatial accuracy of 4 µm.

Feasibility of electrochemical chloride extraction from structural reinforced concrete using a sprayed conductive graphite powder–cement paste as anode

This article summarizes research on the application of a conductive cement paste as an anode in the now classical technique of electrochemical extraction of chlorides applied to a concrete structural element by spraying the paste on the surface of a concrete structural element, a pillar. Sprayed conductive cement paste, by adding graphite powder, is particularly useful to treat sizable vertical surfaces such are structural supports. Outcomes indicate that this kind of anode not only provides electrochemical chloride removal with similar efficiency, but also is able to retain moisture even without the use of a continuous dampening system.

Steel Pedestrian Bridge to Protect a Unique Tree

This paper describes the “Variation Guggenheim 3: Mirador de la palmera” project, situated in Daya Vieja (Alicante-Spain). This structure is inspired by the Guggenheim museum of New York and is designed to protect a land-mark palm-tree from wind loads. This six – trunk palm tree was declared monument by the Valencian government in 2012. The structure that now protect it appears to fly around de palm tree creating a helicoidally skywalk made of steel, while retrofitting the lateral trunks of the tree to protect them from collapse. An 18 m. long straight beam starts on the top of this helix, and stretches towards a lookout point that offers a view of the whole village and its surroundings. The reduction of the visual impact of the structure on the tree was a major aim for the project design. The structural elements are as slender as possible to avoid the visual obstruction of tree. They are painted white, while the walkway steel corrugated plate is painted green in order to highlight its neat shape among the blur created by the apparent mess of bars of the supporting structure. The two main piles of this pedestrian bridge were designed in steel and geometrically resemble trees. A Ground Penetrating Radar analysis was performed to detect the palm root location and to decide the best foundation system. Slender cast in-situ steel-concrete micropiles along with a concrete pile-cap, raised some centimeters above the ground level, were used to reduce the damage to the roots. The projected pile-cap is a slender, continuous, circular ring; which geometry resembles a concrete bench. This structure has been a finalist in the Architecture Awards for the 2010-2014 best construction projects, held by the Diputación de Alicante.

The Impact of Banking Structural Reform on Household Retail Finance. ECRI Commentary No. 13, 7 October 2014

There are two main objectives behind the EC proposal on banking structural reform: the financial stability objective and the economic efficiency objective. If it is implemented, the reform should reinforce the stability and economic efficiency of household retail activities through lower contagion, better resolvability in the event of failure, more harmonised supervisory practices across the EU and more resilient household demand for retail loans. However, it could also trigger counterproductive effects that could partly undermine the expected benefits. These potential negative effects are not appropriately assessed in the impact study of the proposal published in January 2014 and will require further consideration in the coming months. In particular, the stability of household retail finance could be strengthened by placing more emphasis on bankruptcy risks of retail banks; the transfer of existing systemic activities towards less regulated and supervised markets and reputational risk. A better analysis of the borrowing costs for households (impacted by the potential decreasing diversification of the funding base of banks and scarcer liquidity) and implementation costs could help regulators to achieve the objective of efficient household activities.

A success story for the EU and seasonal workers’ rights without reinventing the wheel. EPC Policy Brief, 28 March 2014

Despite the economic crisis with resulting high unemployment, EU economies face vacancies across the skill spectrum. At the low end there is a structural need when it comes to seasonal work. The Seasonal Workers Directive was launched at the same time as the Inter-Corporate Transferees (ICTs) Directive in 2010 – as part of the Commission’s 2005 Policy Plan on Legal Migration – and initially appeared to be more troublesome, with the stigma of ‘migrants stealing local jobs’ haunting it. However, without the provisions for intra-EU mobility that have plagued the ICTs Directive, the Seasonal Workers Directive became less problematic despite the fact that seasonal workers are more numerous than intra-corporate transferees. This Policy Brief looks at how negotiating parties ensured a focus not only on the needs of the European labour market, but also saw an opportunity to bring added value to seasonal workers’ rights, through equal treatment to EU nationals. It assesses the final outcome of three and a half years of intra-EU negotiation, looking at the rights gained for seasonal migrants, the level of harmonization achieved, and the future of migration policy with the strategic guidelines for the area of freedom, security and justice in mind.

Application of the Equivalent Static Analysis method to the design of a steel frame structure with added viscous dampers

All the structures designed by engineers are vulnerable to natural disasters including floods and earthquakes. The energy released during strong ground motions should be dissipated by structural elements. Before 1990’s, this energy was expected to be dissipated through the beams and columns which at the same time were a part of gravity-load-resisting system. However, the main disadvantage of this idea was that gravity-resisting-frame was not repairable. Hence, during 1990’s, the idea of designing passive energy dissipation systems, including dampers, emerged. At the beginning, main problem was lack of guidelines for passive energy dissipation systems. Although till 2000 many guidelines and procedures where published, yet most of them were based on complicated analysis which was not so convenient for engineers and practitioners. In order to solve this problem recently some alternative design methods are proposed including 1. Lopez Garcia (2001) simple procedure for optimal damper configuration in MDOF structures 2. Christopoulos and Filiatrault (2006) trial and error procedure 3. Silvestri et al. (2010) Five-Step Method. 4. Palermo et al. (2015) Direct Five-Step Method. 5. Palermo et al. (2016) Simplified Equivalent Static Analysis (ESA). In this study, effectiveness and differences between last three alternative methods have been evaluated.

Studies on the seismic design of low-rise steel buildings /

Mode of access: Internet.

Methods to reduce built-in residual stresses in steel bridge diaphragms (Phase I) /

"July 2000."

Structural steelwork.

Includes index.

Identification of dislocated workers utilizing unemployment insurance administrative data : results from a five state analysis /

"April 1984."

Displaced workers : new options for a changing economy /

Bibliography: p. 16.

Hourly compensation costs for production workers : 40 manufacturing industries ... countries, 1975 and ... /

Latest issue consulted: 1983-93.