STATE OF CHARGE BALANCING DROOP CONTROL

This thesis presents a load sharing method applied in a distributed micro grid system. The goal of this method is to balance the state-of-charge (SoC) of each parallel connected battery and make it possible to detect the average SoC of the system by measuring bus voltage for all connected modules. In this method the reference voltage for each battery converter is adjusted by adding a proportional SoC factor. Under such setting the battery with a higher SoC will output more power, whereas the one with lower SoC gives out less. Therefore the higher SoC battery will use its energy faster than the lower ones, and eventually the SoC and output power of each battery will converge. And because the reference voltage is related to SoC status, the information of the average SoC in this system could be shared for all modules by measuring bus voltage. The SoC balancing speed is related to the SoC droop factors. This SoC-based load sharing control system is analyzed in feasibility and stability. Simulations in MATLAB/Simulink are presented, which indicate that this control scheme could balance the battery SoCs as predicted. The observation of SoC sharing through bus voltage was validated in both software simulation and hardware experiments. It could be of use to non-communicated distributed power system in load shedding and power planning.

A State of War: Florida from 1939 to 1945

World War II profoundly impacted Florida. The military geography of the State is essential to an understanding the war. The geostrategic concerns of place and space determined that Florida would become a statewide military base. Florida’s attributes of place such as climate and topography determined its use as a military academy hosting over two million soldiers, nearly 15 percent of the GI Army, the largest force theUS ever raised. One-in-eight Floridians went into uniform. Equally,Florida’s space on the planet made it central for both defensive and offensive strategies. The Second World War was a war of movement, and Florida was a major jump off point forUSforce projection world-wide, especially of air power. Florida’s demography facilitated its use as a base camp for the assembly and engagement of this military power. In 1940, less than two percent of the US population lived in Florida, a quiet, barely populated backwater of the United States.[1] But owing to its critical place and space, over the next few years it became a 65,000 square mile training ground, supply dump, and embarkation site vital to the US war effort. Because of its place astride some of the most important sea lanes in the Atlantic World,Florida was the scene of one of the few Western Hemisphere battles of the war. The militarization ofFloridabegan long before Pearl Harbor. The pre-war buildup conformed to theUSstrategy of the war. The strategy of theUS was then (and remains today) one of forward defense: harden the frontier, then take the battle to the enemy, rather than fight them inNorth America. The policy of “Europe First,” focused the main US war effort on the defeat of Hitler’sGermany, evaluated to be the most dangerous enemy. In Florida were established the military forces requiring the longest time to develop, and most needed to defeat the Axis. Those were a naval aviation force for sea-borne hostilities, a heavy bombing force for reducing enemy industrial states, and an aerial logistics train for overseas supply of expeditionary campaigns. The unique Florida coastline made possible the seaborne invasion training demanded for USvictory. The civilian population was employed assembling mass-produced first-generation container ships, while Floridahosted casualties, Prisoners-of-War, and transient personnel moving between the Atlantic and Pacific. By the end of hostilities and the lifting of Unlimited Emergency, officially on December 31, 1946, Floridahad become a transportation nexus. Florida accommodated a return of demobilized soldiers, a migration of displaced persons, and evolved into a modern veterans’ colonia. It was instrumental in fashioning the modern US military, while remaining a center of the active National Defense establishment. Those are the themes of this work. [1] US Census of Florida 1940. Table 4 – Race, By Nativity and Sex, For the State. 14.

Switching Patterns and Steady-State Analysis of Grid-Connected and Stand-Alone Single-Stage Boost-Inverters for PV Applications

Renewable or sustainable energy (SE) sources have attracted the attention of many countries because the power generated is environmentally friendly, and the sources are not subject to the instability of price and availability. This dissertation presents new trends in the DC-AC converters (inverters) used in renewable energy sources, particularly for photovoltaic (PV) energy systems. A review of the existing technologies is performed for both single-phase and three-phase systems, and the pros and cons of the best candidates are investigated. In many modern energy conversion systems, a DC voltage, which is provided from a SE source or energy storage device, must be boosted and converted to an AC voltage with a fixed amplitude and frequency. A novel switching pattern based on the concept of the conventional space-vector pulse-width-modulated (SVPWM) technique is developed for single-stage, boost-inverters using the topology of current source inverters (CSI). The six main switching states, and two zeros, with three switches conducting at any given instant in conventional SVPWM techniques are modified herein into three charging states and six discharging states with only two switches conducting at any given instant. The charging states are necessary in order to boost the DC input voltage. It is demonstrated that the CSI topology in conjunction with the developed switching pattern is capable of providing the required residential AC voltage from a low DC voltage of one PV panel at its rated power for both linear and nonlinear loads. In a micro-grid, the active and reactive power control and consequently voltage regulation is one of the main requirements. Therefore, the capability of the single-stage boost-inverter in controlling the active power and providing the reactive power is investigated. It is demonstrated that the injected active and reactive power can be independently controlled through two modulation indices introduced in the proposed switching algorithm. The system is capable of injecting a desirable level of reactive power, while the maximum power point tracking (MPPT) dictates the desirable active power. The developed switching pattern is experimentally verified through a laboratory scaled three-phase 200W boost-inverter for both grid-connected and stand-alone cases and the results are presented.

Development of Physics-based Models and Design Optimization of Power Electronic Conversion Systems

The main objective for physics based modeling of the power converter components is to design the whole converter with respect to physical and operational constraints. Therefore, all the elements and components of the energy conversion system are modeled numerically and combined together to achieve the whole system behavioral model. Previously proposed high frequency (HF) models of power converters are based on circuit models that are only related to the parasitic inner parameters of the power devices and the connections between the components. This dissertation aims to obtain appropriate physics-based models for power conversion systems, which not only can represent the steady state behavior of the components, but also can predict their high frequency characteristics. The developed physics-based model would represent the physical device with a high level of accuracy in predicting its operating condition. The proposed physics-based model enables us to accurately develop components such as; effective EMI filters, switching algorithms and circuit topologies [7]. One of the applications of the developed modeling technique is design of new sets of topologies for high-frequency, high efficiency converters for variable speed drives. The main advantage of the modeling method, presented in this dissertation, is the practical design of an inverter for high power applications with the ability to overcome the blocking voltage limitations of available power semiconductor devices. Another advantage is selection of the best matching topology with inherent reduction of switching losses which can be utilized to improve the overall efficiency. The physics-based modeling approach, in this dissertation, makes it possible to design any power electronic conversion system to meet electromagnetic standards and design constraints. This includes physical characteristics such as; decreasing the size and weight of the package, optimized interactions with the neighboring components and higher power density. In addition, the electromagnetic behaviors and signatures can be evaluated including the study of conducted and radiated EMI interactions in addition to the design of attenuation measures and enclosures.

Hybrid power system intelligent operation and protection involving plug-in electric vehicles

Two key solutions to reduce the greenhouse gas emissions and increase the overall energy efficiency are to maximize the utilization of renewable energy resources (RERs) to generate energy for load consumption and to shift to low or zero emission plug-in electric vehicles (PEVs) for transportation. The present U.S. aging and overburdened power grid infrastructure is under a tremendous pressure to handle the issues involved in penetration of RERS and PEVs. The future power grid should be designed with for the effective utilization of distributed RERs and distributed generations to intelligently respond to varying customer demand including PEVs with high level of security, stability and reliability. This dissertation develops and verifies such a hybrid AC-DC power system. The system will operate in a distributed manner incorporating multiple components in both AC and DC styles and work in both grid-connected and islanding modes. ^ The verification was performed on a laboratory-based hybrid AC-DC power system testbed as hardware/software platform. In this system, RERs emulators together with their maximum power point tracking technology and power electronics converters were designed to test different energy harvesting algorithms. The Energy storage devices including lithium-ion batteries and ultra-capacitors were used to optimize the performance of the hybrid power system. A lithium-ion battery smart energy management system with thermal and state of charge self-balancing was proposed to protect the energy storage system. A grid connected DC PEVs parking garage emulator, with five lithium-ion batteries was also designed with the smart charging functions that can emulate the future vehicle-to-grid (V2G), vehicle-to-vehicle (V2V) and vehicle-to-house (V2H) services. This includes grid voltage and frequency regulations, spinning reserves, micro grid islanding detection and energy resource support. ^ The results show successful integration of the developed techniques for control and energy management of future hybrid AC-DC power systems with high penetration of RERs and PEVs.^

The modern state and the re-creation of the indigenous other: The case of the authentic Sami in Sweden and the white man's Indian in the United States of America

The present study comparatively examined the socio-political and economic transformation of the indigenous Sámi in Sweden and the Indian American in the United States of America occurring first as a consequence of colonization and later as a product of interaction with the modern territorial and industrial state, from approximately 1500 to 1900. ^ The first colonial encounters of the Europeans with these autochthonous populations ultimately created an imagery of the exotic Other and of the noble savage. Despite these disparaging representations, the cross-cultural settings in which these interactions took place also produced the hybrid communities and syncretic life that allowed levels of cultural accommodation, autonomous space, and indigenous agency to emerge. By the nineteenth century, however, the modern territorial and industrial state rearranges the dynamics and reaches of power across a redefined territorial sovereign space, consequently, remapping belongingness and identity. In this context, the status of indigenous peoples, as in the case of Sámi and of Indian Americans, began to change at par with industrialization and with modernity. At this point in time, indigenous populations became a hindrance to be dealt with the legal re-codification of Indigenousness into a vacuumed limbo of disenfranchisement. It is, thus, the modern territorial and industrial state that re-creates the exotic into an indigenous Other. ^ The present research showed how the initial interaction between indigenous and Europeans changed with the emergence of the modern state, demonstrating that the nineteenth century, with its fundamental impulses of industrialism and modernity, not only excluded and marginalized indigenous populations because they were considered unfit to join modern society, it also re-conceptualized indigenous identity into a constructed authenticity.^

Probabilistic Security Constrained Fuzzy Power Flow Models

In restructured power systems, generation and commercialization activities became market activities, while transmission and distribution activities continue as regulated monopolies. As a result, the adequacy of transmission network should be evaluated independent of generation system. After introducing the constrained fuzzy power flow (CFPF) as a suitable tool to quantify the adequacy of transmission network to satisfy 'reasonable demands for the transmission of electricity' (as stated, for instance, at European Directive 2009/72/EC), the aim is now showing how this approach can be used in conjunction with probabilistic criteria in security analysis. In classical security analysis models of power systems are considered the composite system (generation plus transmission). The state of system components is usually modeled with probabilities and loads (and generation) are modeled by crisp numbers, probability distributions or fuzzy numbers. In the case of CFPF the component’s failure of the transmission network have been investigated. In this framework, probabilistic methods are used for failures modeling of the transmission system components and possibility models are used to deal with 'reasonable demands'. The enhanced version of the CFPF model is applied to an illustrative case.

A NEW DC UPS FOR DC POWER DISTRIBUTION SYSTEM IN DATA CENTER

In recent years, the 380V DC and 48V DC distribution systems have been extensively studied for the latest data centers. It is widely believed that the 380V DC system is a very promising candidate because of its lower cable cost compared to the 48V DC system. However, previous studies have not adequately addressed the low reliability issue with the 380V DC systems due to large amount of series connected batteries. In this thesis, a quantitative comparison for the two systems has been presented in terms of efficiency, reliability and cost. A new multi-port DC UPS with both high voltage output and low voltage output is proposed. When utility ac is available, it delivers power to the load through its high voltage output and charges the battery through its low voltage output. When utility ac is off, it boosts the low battery voltage and delivers power to the load form the battery. Thus, the advantages of both systems are combined and the disadvantages of them are avoided. High efficiency is also achieved as only one converter is working in either situation. Details about the design and analysis of the new UPS are presented. For the main AC-DC part of the new UPS, a novel bridgeless three-level single-stage AC-DC converter is proposed. It eliminates the auxiliary circuit for balancing the capacitor voltages and the two bridge rectifier diodes in previous topology. Zero voltage switching, high power factor, and low component stresses are achieved with this topology. Compared to previous topologies, the proposed converter has a lower cost, higher reliability, and higher efficiency. The steady state operation of the converter is analyzed and a decoupled model is proposed for the converter. For the battery side converter as a part of the new UPS, a ZVS bidirectional DC-DC converter based on self-sustained oscillation control is proposed. Frequency control is used to ensure the ZVS operation of all four switches and phase shift control is employed to regulate the converter output power. Detailed analysis of the steady state operation and design of the converter are presented. Theoretical, simulation, and experimental results are presented to verify the effectiveness of the proposed concepts.

State-narco networks and the ‘War on Drugs’ in post-transition Bolivia, with special reference to 1989-1993

This thesis examines the development of state-narco networks in post-transition Bolivia. Mainstream discourses of drugs tend to undertheorise such relationships, holding illicit economies, weak states and violence as synergistic phenomena. Such assumptions fail to capture the nuanced relations that emerge between the state and the drug trade in different contexts, their underlying logics and diverse effects. As an understudied case, Bolivia offers novel insights into these dynamics. Bolivian military authoritarian governments (1964-1982), for example, integrated drug rents into clientelistic systems of governance, helping to establish factional coalitions and reinforce regime authority. Following democratic transition in 1982 and the escalation of US counterdrug efforts, these stable modes of exchange between the state and the coca-cocaine economy fragmented. Bolivia, though, continued to experience lower levels of drug-related violence than its Andean neighbours, and sustained democratisation despite being a major drug producer. Focusing on the introduction of the Andean Initiative (1989-1993), I explore state-narco interactions during this period of flux: from authoritarianism to (formal) democracy, and from Cold War to Drug War. As such, the thesis transcends the conventional analyses of the drugs literature and orthodox readings of Latin American narco-violence, providing insights into the relationship between illicit economies and democratic transition, the regional role of the US, and the (unintended) consequences of drug policy interventions. I utilise a mixed methods approach to offer discrete perspectives on the object of study. Drawing on documentary and secondary sources, I argue that state-narco networks were interwoven with Bolivia’s post-transition political settlement. Uneven democratisation ensured pockets of informalism, as clientelistic and authoritarian practices continued. This included police and military autonomy, and tolerance of drug corruption within both institutions. Non-enforcement of democratic norms of accountability and transparency was linked to the maintenance of fragile political equilibrium. Interviews with key US and Bolivian elite actors also revealed differing interpretations of state-narco interactions. These exposed competing agendas, and were folded into alternative paradigms and narratives of the ‘war on drugs’. The extension of US Drug War goals and the targeting of ‘corrupt’ local power structures, clashed with local ambivalence towards the drug trade, opposition to destabilising, ‘Colombianised’ policies and the claimed ‘democratising mission’ of the Bolivian government. In contrasting these US and Bolivian accounts, the thesis shows how real and perceived state-narco webs were understood and navigated by different actors in distinct ways. ‘Drug corruption’ held significance beyond simple economic transaction or institutional failure. Contestation around state-narco interactions was enmeshed in US-Bolivian relations of power and control.

Locating the maximum power point for thermoelectric generators for constant heat operation

Thermoelectric generators (TEGs) are solid-state devices that can be used for the direct conversion between heat and electricity. These devices are an attractive option for generating clean energy from heat. There are two modes of operation for TEGs; constant heat and constant temperature. It is a well-known fact that for constant temperature operation, TEGs have a maximum power point lying at half the open circuit voltage of the TEG, for a particular temperature. This work aimed to investigate the position of the maximum power point for Bismuth Telluride TEGs working under constant heat conditions i.e. the heat supply to the TEG is fixed however the temperature across the TEG can vary depending upon its operating conditions. It was found that for constant heat operation, the maximum power point for a TEG is greater than half the open circuit voltage of the TEG.

Soft Power del Vaticano en el reconocimiento de Palestina como Estado

Desde 1945, el inicio de la cuestión palestina, el país ha sufrido una serie de transformaciones e intervenciones en su soberanía y en legitimidad, las cuales siguen en discusión actualmente; y han dado como resultado el estudio del reconocimiento de Palestina como Estado. Es pertinente hacer un acercamiento a este tema desde la variable religiosa (Vaticano), teniendo en cuenta el gran número de lugares sagrados que hay en la región de Palestina y la variable religiosa del conflicto Palestino-israelí. Desde la mirada del Soft Power, concepto que ha venido tomando fuerza en la academia desde 1980, podemos acercarnos al objeto de estudio y dilucidar las injerencias de este actor. Mediante una aproximación cualitativa, que conlleva análisis del discurso, análisis histórico y análisis de política exterior, se logrará obtener el resultado esperado, que es entender de qué manera el Vaticano ejerce influencia (ideológica y cultural) en el Sistema Internacional, en el asunto del reconocimiento de Palestina como Estado.

Advances in integration of photovoltaic power and energy production in practical systems

This thesis presents advances in integration of photovoltaic (PV) power and energy in practical systems, such as existing power plants in buildings or directly integrated in the public electrical grid. It starts by providing an analyze of the current state of PV power and some of its limitations. The work done in this thesis begins by providing a model to compute mutual shading in large PV plants, and after provides a study of the integration of a PV plant in a biogas power plant. The remainder sections focus on the work done for project PVCROPS, which consisted on the construction and operation of two prototypes composed of a PV system and a novel battery connected to a building and to the public electrical grid. These prototypes were then used to test energy management strategies and validate the suitability of the two advanced batteries (a lithium-ion battery and a vanadium redox ow battery) for households (BIPV) and PV plants. This thesis is divided in 7 chapters: Chapter 1 provides an introduction to explain and develop the main research questions studied for this thesis; Chapter 2 presents the development of a ray-tracing model to compute shading in large PV elds (with or without trackers); Chapter 3 shows the simulation of hybridizing a biogas plant with a PV plant, using biogas as energy storage; Chapters 4 and 5 present the construction, programming, and initial operation of both prototypes (Chapter 4), EMS testing oriented to BIPV systems (Chapter 5). Finally, Chapters 6 provides some future lines of investigation that can follow this thesis, and Chapter 7 shows a synopsis of the main conclusions of this work; Resumo: Avanços na integracão de potência fotovoltaica e producão de energia em sistemas práticos Esta tese apresenta avanços na integração de potência e energia fotovoltaica (PV) em sistemas práticos, tais como centrais existentes ou a rede eléctrica pública. Come ça por analisar o estado corrente do fotovoltaico no mundo e aborda algumas das suas limitações. O trabalho feito para esta tese de doutoramento começou pelo desenvolvimento de um modelo para calcular os sombreamentos que ocorrem em grandes campos fotovoltaicos, e depois apresenta um estudo sobre a integração um sistema fotovoltaico em uma central eléctrica a bióg as. As ultimas secções da tese focam-se no trabalho feito para o projecto PVCROPS, que consistiu na construção e operação de dois demonstratores, cada um formado por um sistema fotovoltaico e bateria conectados a um edíficio e a rede eléctrica pública. Estes protótipos foram posteriormente utilizados para testar estratégias de gestão de energia (EMS) e para validar a operação de duas baterias avançadas (bateria de Iões de Li tio e bateria de Fluxo Redox de Van adio) e a sua utiliza ção para habitações e centrais PV. A tese está dividida em 7 capitulos: O capitulo 1 apresenta uma introdução para explicar e desenvolver as principais questões que foram investigadas nesta tese; O capitulo 2 mostra o desenvolvimento de um modelo baseado em traçados de raios para calcular sombreamentos mútuos em grandes centrais PV (com e sem seguidores); O capitulo 3 mostra a simulação da hibridização de uma central electrica a biogas com uma central PV, e utilizando o biógas como armazenamento de energia. Os capitulos 4 e 5 apresentam a construção, programação e operação inicial dos dois demonstradores (Capitúlo 4), o teste de EMS orientadas para sistemas PV em habitações (Capítulo 5). Finalmente, o capítulo 6 sugere algumas futuras linhas de investigação que poderão seguir esta tese, e o Capítulo 7 faz uma sinopse das principais conclusões deste trabalho.

Design and characterization of wideband Hall current sensors in BCD technology for smart power and metering applications

Power electronic circuits are moving towards higher switching frequencies, exploiting the capabilities of novel devices to shrink the dimension of passive components. This trend demands sensors capable enough to operate at such high frequencies. This thesis aims to demonstrate through experimental characterization, the broadband capability of a fully integrated CMOS X-Hall current sensor in current mode interfaced with a transimpedance amplifier (TIA), chip CH09, realized in CMOS technology for power electronics applications such as power converters. The system exploits a common-mode control system to operate the dual supply system, 5-V for the X-Hall probe and 1.2-V for the readout. The developed prototype achieves a maximum acquisition bandwidth of 12 MHz, a power consumption of 11.46 mW, resolution of 39 mArms, a sensitivity of 8 % /T, and a FoM of 569-MHz/A2mW, significantly higher than current state-of-the-art. Further enhancements were proposed to CH09 as a new chip CH100, aiming for accuracy levels prerequisite for a real-time power electronic application. The TIA was optimized for a wider bandwidth of 26.7 MHz with nearly 30% reduction of the integrated input referred noise of 26.69 nArms at the probe-AFE interface in the frequency band of DC-30 MHz, and a 10% improvement in the dynamic range. The expected input range is 5-A. The chip incorporates a dual sensing chain for differential sensing to overcome common mode interferences. A novel offset cancellation technique is proposed that would require switching of polarity of bias currents. Thermal gain drift was improved by a factor of 8 and will be digitally calibrated utilizing a new built-in temperature sensor with a post calibration measurement accuracy greater than 1%. The estimated power consumption of the entire system is 55.6 mW. Both prototypes have been implemented through a 90-nm microelectronic process from STMicroelectronics and occupy a silicon area of 2.4 mm2.

Power converters in WBG device technology for automotive applications and characterization setups for GaN power transistors

This PhD dissertation envisages the design of innovative power converters exploiting WBG devices to get state-of-the-art performance in products intended for industrial applications of automotive field. The collaborations with different specialized companies, provided the opportunity to access commercially-available state-of-the-art SiC and GaN technologies and the possibility to realize innovative converter prototypes. Concerning SiC technology, the complete design of a $350kW$ Battery Emulator instrument in collaboration with a company leader in the automotive testing sector, was carried out from scratch exploiting state-of-the-art SiC power-modules, planar magnetics and top-notch MCU technologies. Discrete high-voltage GaN switches were exploited in the Power Supplies design for automotive charger application to target improved performances compared to the market state-of-the-art. Specifically, two high-efficiency prototypes, an AC/DC converter and a DC/DC converter of $7.5kW$, have been realized for this purpose. To further investigate the characteristics of state-of-the-art GaN power devices two measurement set-ups have been designed. In particular, the trapping phenomenon causing the collapse of drain current during ON-state with a consequent degradation of ON-resistance has been analyzed.

Long-term reliability of power GaN HEMTS

The world is quickly changing, and the field of power electronics assumes a pivotal role in addressing the challenges posed by climate change, global warming, and energy management. The introduction of wide-bandgap semiconductors, particularly gallium nitride (GaN), in contrast to the traditional silicon technology, is leading to lightweight, compact and evermore efficient circuitry. However, GaN technology is not mature yet and still presents reliability issues which constrain its widespread adoption. Therefore, GaN reliability is a hotspot for the research community. Extensive efforts have been directed toward understanding the physical mechanisms underlying the performance and reliability of GaN power devices. The goal of this thesis is to propose a novel in-circuit degradation analysis in order to evaluate the long-term reliability of GaN-based power devices accurately. The in-circuit setup is based on measure-stress-measure methodology where a high-speed synchronous buck converter ensures the stress while the measure is performed by means of full I-V characterizations. The switch from stress mode to characterization mode and vice versa is automatic thanks to electromechanical and solid-state relays controlled by external unit control. Because these relays are located in critical paths of the converter layout, the design has required a comprehensive study of electrical and thermal problems originated by the use of GaN technology. In addition, during the validation phase of the converter, electromagnetic-lumped-element circuit simulations are carried out to monitor the signal integrity and junction temperature of the devices under test. However, the core of this work is the in-circuit reliability analysis conducted with 80 V GaN HEMTs under several operating conditions of the converter in order to figure out the main stressors which contribute to the device's degradation.