Magnetic shielding properties of a superconducting hollow cylinder containing slits: Modelling and experiment

This paper deals with the magnetic properties of bulk high temperature superconducting cylinders used as magnetic shields. We investigate, both numerically and experimentally, the magnetic properties of a hollow cylinder with two axial slits which cut the cylinder in equal halves. Finite element method modelling has been used with a three-dimensional geometry to help us in understanding how the superconducting currents flow in such a cut cylinder and therefore how the magnetic shielding properties are affected, depending on the magnetic field orientation. Modelling results show that the slits block the shielding current flow and act as an entrance channel for the magnetic flux lines. The contribution of the slits to the total flux density that enters the cylinder is studied through the angle formed between the applied field and the internal field. The modelled data agree nicely with magnetic shielding properties measured on a bulk Bi-2212 hollow cylinder at 77K. The results demonstrate that the magnetic flux penetration in such a geometry can be modelled successfully using only two parameters of the superconductor (constant J c and n value), which were determined from magnetic measurements on the plain cylinder. © 2012 IOP Publishing Ltd.

Novel experiment on in-cylinder desorption of fuel from the oil layer

A technique has been developed to measure the desorption and subsequent oxidation of fuel in the oil layer by spiking the oil with liquid fuel and firing the engine on gaseous fuel or motoring with air. Experiments suggest that fuel desorption is not diffusion limited above 50°C and indicated that approximately two to four percent of the cylinder oil layer is fresh oil from the sump. The increase in hydrocarbon emissions is of the order of 100 ppmC1 per 1% liquid fuel introduced into the fresh oil in a methane fired engine at mid-speed and light load conditions. Calculations indicate that fuel desorbing from oil is much more likely to produce hydrocarbon emissions than fuel emerging from crevices. © Copyright 1994 Society of Automotive Engineers, Inc.

Neutronic optimization in high conversion Th-233U fuel assembly with simulated annealing

This paper reports on fuel design optimization of a PWR operating in a self sustainable Th-233U fuel cycle. Monte Carlo simulated annealing method was used in order to identify the fuel assembly configuration with the most attractive breeding performance. In previous studies, it was shown that breeding may be achieved by employing heterogeneous Seed-Blanket fuel geometry. The arrangement of seed and blanket pins within the assemblies may be determined by varying the designed parameters based on basic reactor physics phenomena which affect breeding. However, the amount of free parameters may still prove to be prohibitively large in order to systematically explore the design space for optimal solution. Therefore, the Monte Carlo annealing algorithm for neutronic optimization is applied in order to identify the most favorable design. The objective of simulated annealing optimization is to find a set of design parameters, which maximizes some given performance function (such as relative period of net breeding) under specified constraints (such as fuel cycle length). The first objective of the study was to demonstrate that the simulated annealing optimization algorithm will lead to the same fuel pins arrangement as was obtained in the previous studies which used only basic physics phenomena as guidance for optimization. In the second part of this work, the simulated annealing method was used to optimize fuel pins arrangement in much larger fuel assembly, where the basic physics intuition does not yield clearly optimal configuration. The simulated annealing method was found to be very efficient in selecting the optimal design in both cases. In the future, this method will be used for optimization of fuel assembly design with larger number of free parameters in order to determine the most favorable trade-off between the breeding performance and core average power density.

Effects of the biodiesel fuel physical properties on the swirl stabilised spray combustion characteristics

An increasin g interest in biofuel applications in modern engines requires a better understanding of biodiesel combustion behaviour. Many numerical studies have been carried out on unsteady combustion of biodiesel in situations similar to diesel engines, but very few studies have been done on the steady combustion of biodiesel in situations similar to a gas turbine combustor environment. The study of biodiesel spray combustion in gas turbine applications is of special interest due to the possible use of biodiesel in the power generation and aviation industries. In modelling spray combustion, an accurate representation of the physical properties of the fuel is a first important step, since spray formation is largely influenced by fuel properties such as viscosity, density, surface tension and vapour pressure. In the present work, a calculated biodiesel properties database based on the measured composition of Fatty Acid Methyl Esters (FAME) has been implemented in a multi-dimensional Computational Fluid Dynamics (CFD) spray simulation code. Simulations of non-reacting and reacting atmospheric-pressure sprays of both diesel and biodiesel have been carried out using a spray burner configuration for which experimental data is available. A pre-defined droplet size probability density function (pdf) has been implemented together with droplet dynamics based on phase Doppler anemometry (PDA) measurements in the near-nozzle region. The gas phase boundary condition for the reacting spray cases is similar to that of the experiment which employs a plain air-blast atomiser and a straight-vane axial swirler for flame stabilisation. A reaction mechanism for heptane has been used to represent the chemistry for both diesel and biodiesel. Simulated flame heights, spray characteristics and gas phase velocities have been found to compare well with the experimental results. In the reacting spray cases, biodiesel shows a smaller mean droplet size compared to that of diesel at a constant fuel mass flow rate. A lack of sensitivity towards different fuel properties has been observed based on the non-reacting spray simulations, which indicates a need for improved models of secondary breakup. By comparing the results of the non-reacting and reacting spray simulations, an improvement in the complexity of the physical modelling is achieved which is necessary in the understanding of the complex physical processes involved in spray combustion simulation. Copyright © 2012 SAE International.

The role of cell-surface-bound phosphatases in species competition within natural phytoplankton assemblage: an in situ experiment

Despite it is widely acknowledged that the ability to hydrolyze dissolved organic matter using extracellular phosphatases is diverse in fresh water phytoplankton, the competition within single species related to presence and quantity of cell-surface-bound phosphatases has not been examined in natural conditions yet. Here, we studied phytoplankton species competition in a freshwater reservoir during an in situ experiment. A natural plankton community, with the exclusion of large zooplankton, was enclosed in permeable dialysis bags inside two large containers of different bioavailable phosphate concentrations. Phytoplankton species biomass and the abundance of bacteria were determined in purpose to compare the development of enclosed microbial communities. Total and cell-surface-bound phosphatase activities in the phytoplankton were investigated using the Fluorescently Labelled Enzyme Activity (FLEA) technique that allows for direct microscopic detection of phosphatase-positive cells and, with image cytometry, enables quantification of phosphatase hydrolytic capacity. Production of extracellular phosphatases was not completely inhibited or stopped in the phosphate-enriched environment, phytoplankton cells only showed the activity less often. Under the phosphate-nonenriched conditions, the production of phosphatases was enhanced, but active species did not proliferate amongst phytoplankton assemblage. Further, specific growth rates of the phosphatase-positive species in the non-enriched environment were lower than the same phosphatase-positive species in phosphate-enriched environment. Interestingly, the phosphatase-positive cells of Ankyra ancora increased their size in both treatments equally, although the population in phosphate-enriched environment grew much faster and the cell-specific phosphatase activity was lower. We hypothesize that brand new daughter cells had sufficient phosphorus reserves and therefore did not employ extracellular phosphatases until they matured and needed extra bioavailable phosphorus to support their metabolism before cell division. Based on presented in situ experiment, we propose that the ability to hydrolyze organic polymers and particles with cell-surface-hound phosphatases is advantageous for longer persistence of given population in a phosphate-scarce environment; although phosphatase-positive species cannot dominate the reservoir phytoplankton solely because of specific phosphorus-scavenging strategy.

Light histories influence the impacts of solar ultraviolet radiation on photosynthesis and growth in a marine diatom, Skeletonema costatum

Phytoplanktonic species acclimated to high light are known to show less photoinhibition. However, little has been documented on how cells grown under indoor conditions for decades without exposure to UV radiation (UVR, 280-400 nm) would respond differently to solar UVR compared to those in situ grown under natural solar radiation. Here, we have shown the comparative photosynthetic and growth responses to solar UVR in an indoor-(IS) and a naturally grown (WS) Skeletonema costatum type. In short-term experiment (<1 day), phi(PSII) and photosynthetic carbon fixation rate were more inhibited by UVR in the IS than in the WS cells. The rate of UVR-induced damages of PSII was faster and their repair was significantly slower in IS than in WS. Even under changing solar radiation simulated for vertical mixing, solar UVR-induced higher inhibition of photosynthetic rate in IS than in WS cells. During long-term (10 days) exposures to solar radiation, the specific growth rate was much lower in IS than WS at the beginning, then increased 3 days later to reach an equivalent level as that of WS. UVR-induced inhibition of photosynthetic carbon fixation in the IS was identical with that of WS at the end of the long-term exposure. The photosynthetic acclimation was not accompanied with increased contents of UV-absorbing compounds, indicating that repair processes for UVR-induced damages must have been accelerated or upgraded. (C) 2008 Elsevier B.V. All rights reserved.

Material point method for coupled hydromechanical problems

This paper describes a new formulation of the material point method (MPM) for solving coupled hydromechanical problems of fluid-saturated soil subjected to large deformation. A soil-pore fluid coupled MPM algorithm based on Biot's mixture theory is proposed for solving hydromechanical interaction problems that include changes in water table location with time. The accuracy of the proposed method is examined by comparing the results of the simulation of a one-dimensional consolidation test with the corresponding analytical solution. A sensitivity analysis of the MPM parameters used in the proposed method is carried out for examining the effect of the number of particles per mesh and mesh size on solution accuracy. For demonstrating the capability of the proposed method, a physical model experiment of a large-scale levee failure by seepage is simulated. The behavior of the levee model with time-dependent changes in water table matches well to the experimental observations. The mechanisms of seepage-induced failure are discussed by examining the pore-water pressures, as well as the effective stresses computed from the simulations © 2013 American Society of Civil Engineers.

Electrical addressing of polymer stabilized hyper-twisted chiral nematic liquid crystals with interdigitated electrodes: Experiment and model

Electro-optic switching in short-pitch polymer stabilized chiral nematic liquid crystals was studied and the relative contributions of flexoelectric and dielectric coupling were investigated: polymer stabilization was found to effectively suppress unwanted textural transitions of the chiral nematic liquid crystal and thereby enhance the electro-optical performance (high optical contrast for visible light, a near ideal optical hysteresis, fast electro-optic response). Test cells were studied that possessed interdigitated electrodes to electrically address the liquid crystal. Based on simulations, a well-fitted phenomenological description of the electro-optic response was derived considering both flexoelectro-optic and Kerr-effect based electro-optic response. © 2014 AIP Publishing LLC.

Stable dynamic walking over rough terrain: Theory and experiment

We propose a constructive control design for stabilization of non-periodic trajectories of underactuated mechanical systems. An important example of such a system is an underactuated "dynamic walking" biped robot walking over rough terrain. The proposed technique is to compute a transverse linearization about the desired motion: a linear impulsive system which locally represents dynamics about a target trajectory. This system is then exponentially stabilized using a modified receding-horizon control design. The proposed method is experimentally verified using a compass-gait walker: a two-degree-of-freedom biped with hip actuation but pointed stilt-like feet. The technique is, however, very general and can be applied to higher degree-of-freedom robots over arbitrary terrain and other impulsive mechanical systems. © 2011 Springer-Verlag.

In situ study on the control of toxic Microcystis blooms using phytoplanktivorous fish in the subtropical Lake Taihu of China: A large fish pen experiment

Three large fish pens (0.36 km(2) of each) stocked with silver and bighead carp were set up in Meiliang Bay for controlling toxic Microcystis blooms. The responses of plankton communities and food consumption of silver and bighead carp were studied. Crustacean zooplankton were significantly suppressed in the fish pens. Total phytoplankton biomass, Microcystis biomass and microcystin concentration were lower in the fish pens than in the surrounding lake water, but the difference was not statistically significant. The present stocking density of silver plus bighead carp (about 40 g/m(3) in July) was likely too low to achieve an adequate control of Microcystis. Silver carp fed mainly on phytoplankton but bighead carp mainly on zooplankton: mean zooplankton contribution in the gut was 31.5% for silver carp and 64.7% for bighead carp. Compared with previous studies, both carp species preyed upon more zooplankton because of the abundant food resource. Daily rations of silver and bighead carp were estimated by Egger's model in the main growing season. Filtration rate was calculated from the daily ration and the density of plankton in the lake. During May-October, filtration rates of silver and bighead carp for phytoplankton were 0.22-1.53 L g(-1) h(-1) and 0.02-0.68 L g(-1) h(-1), respectively, and filtration rates for zooplankton were 0.24-0.44 L g(-1) h(-1) and 0.08-1.41 L g(-1) h(-1), respectively. Silver carp had a stronger ability of eliminating phytoplankton than bighead carp. To achieve a successful bioniampulation with a minimum effect of ichthyoeutrophication, the stocking proportion of bighead carp should be controlled in the future practice. (c) 2007 Elsevier B.V All rights reserved.

Effects of the phytoplanktivorous silver carp (Hypophthalmichthys molitrixon) on plankton and the hepatotoxic microcystins in an enclosure experiment in a eutrophic lake, Lake Shichahal in Beijing

The responses of nutrients, water transparency, zooplankton, phytoplankton and microcystins to a gradient of silver carp biomass (0, 18, 55, 110 g/m(3)) were assessed using enclosures in Lake Shichahai (Beijing). Picophytoplankton biomass increased with increasing fish stocking density (r=0.64, p=0.09). Silver carp significantly depressed zooplankton biomass, and thus, zooplankton grazing was too low to control phytoplankton. Intracellular microcystin (MC) content in the enclosures was correlated only to Microcystis biomass in the present study. Microcystis spp. biomass and intracellular microcystins content were much higher in lake water than those of enclosures with and without stocking fish. Stocking of silver carp could be an appropriate in highly productive Lake Shichahai, which naturally lacks of large cladoceran zooplankton. A fish stocking density of 55 g/m(3) was most efficient at controlling Microcystis blooms and increasing water clarity. Mean extracellular MC concentration in the lake water was almost the same with that of the enclosures with fish. (c) 2006 Elsevier B.V. All rights reserved.

Negative effects of Microcystis blooms on the crustacean plankton in an enclosure experiment in the subtropical China

Effects of Microcystis blooms on the crustacean plankton were studied using enclosure experiments during July-September, 2000. Eight enclosures were set in the hypereutrophic Donghu Lake. Different nutrient concentrations through additional nutrient and sediment in enclosures were expected to result in different abundance of Micropystis. From July to early August, the phytoplankton community was dominated by Chlorophyta, Cryptophyta, Bacillariophyta and Cyanophyta other than Microcystis aeruginosa. M. aeruginosa showed a rapid increase during early August in all enclosures and predominated. Crustacean plankton was dominated by the herbivorous Moina micrura, Diaphanosoma brachyurum and Ceriodaphnia cornuta, and the predaceous Mesocyclops sp. and Thermocyclops taihokuensis. During the pre-bloom period, the dynamics of M. micrura population appeared to be mainly affected by the predaceous cyclopoids. With the development of Microcystis blooms, such interaction between M. micrura and cyclopoids seemed weakened, especially when the Microcystis biomass was high. But there was no apparent influence on the interaction between Leptodora kindti and its zooplanktonic prey. The density of two cyclopoids decreased with the enhancement of Microcystis. The density decline of M. micrura was caused by both predation and inhibition by Micropystis. The low food availability of other edible phytoplankton during the blooms led to low densities of both C. cornuta and D. brachyurum by late August. It appears that dense Microcystis blooms exert strong negative effects on the herbivorous cladocerans and the predaceous cyclopoids.