Functionally graded porous scaffolds made of Ti-based agglomerates

Mono- and double-layer porous scaffolds were successfully fabricated using ball-milled agglomerates of Ti and Ti-10Nb-3Mo alloy. For selectively controlling the level of porosity and pore size, the agglomerates were sieved into two different size fractions of 100-300μm and 300-500μm. Compressive mechanical properties were measured on a series of cylindrical sintered compacts with different ratios of solid core diameter to porous layer width. The graded porous scaffolds exhibited stress-strain curves typical for metallic foams with a defined plateau region after yielding. The compressive strengths and elastic moduli ranged from 300 to 700MPa and 14 to 55GPa, respectively, depending on the core diameter and the material used. The obtained properties make these materials suitable for load-bearing implant applications.

The Processing of Aluminum Gasarites via Thermal Decomposition of Interstitial Hydrides

Gasarite structures are a unique type of metallic foam containing tubular pores. The original methods for their production limited them to laboratory study despite appealing foam properties. Thermal decomposition processing of gasarites holds the potential to increase the application of gasarite foams in engineering design by removing several barriers to their industrial scale production. The following study characterized thermal decomposition gasarite processing both experimentally and theoretically. It was found that significant variation was inherent to this process therefore several modifications were necessary to produce gasarites using this method. Conventional means to increase porosity and enhance pore morphology were studied. Pore morphology was determined to be more easily replicated if pores were stabilized by alumina additions and powders were dispersed evenly. In order to better characterize processing, high temperature and high ramp rate thermal decomposition data were gathered. It was found that the high ramp rate thermal decomposition behavior of several hydrides was more rapid than hydride kinetics at low ramp rates. This data was then used to estimate the contribution of several pore formation mechanisms to the development of pore structure. It was found that gas-metal eutectic growth can only be a viable pore formation mode if non-equilibrium conditions persist. Bubble capture cannot be a dominant pore growth mode due to high bubble terminal velocities. Direct gas evolution appears to be the most likely pore formation mode due to high gas evolution rate from the decomposing particulate and microstructural pore growth trends. The overall process was evaluated for its economic viability. It was found that thermal decomposition has potential for industrialization, but further refinements are necessary in order for the process to be viable.

Cell Pattern in Adult Human Corneal Endothelium

A review of the current data on the cell density of normal adult human endothelial cells was carried out in order to establish some common parameters appearing in the different considered populations. From the analysis of cell growth patterns, it is inferred that the cell aging rate is similar for each of the different considered populations. Also, the morphology, the cell distribution and the tendency to hexagonallity are studied. The results are consistent with the hypothesis that this phenomenon is analogous with cell behavior in other structures such as dry foams and grains in polycrystalline materials. Therefore, its driving force may be controlled by the surface tension and the mobility of the boundaries.

DFT STUDIES ON THE MECHANISM OF RING-OPENING POLYMERIZATION OF LACTIDE WITH ADENINE

The use of organic molecules as catalysts for the ring-opening polymerization (ROP) of cyclic esters has gained much interest last years.[1] The use of a molecule of biological interest, able to initiate ROP of cyclic esters without any cocatalyst is even more interesting, as the resulting material will not contain any catalytic residue. Nucleobase-polymer conjugates development is thus an emerging area envisaging biomedical applications.[2] However, they are usually synthesized by tedious multistep procedures. Recently, adenine was used as organoinitiator for the ROP of L-lactide.[3] Reaction conditions involving short reaction times and relatively low temperatures enable the access to adenine-polylactide(Adn-PLA)conjugates in a simple one-step procedure, without additional catalyst and in the absence of solvent. In this study, computational investigations with density functional theory (DFT) were performed in order to clarify the reaction mechanism leading to the desired Adn-PLA. The results show that a hydrogen bond catalytic mechanism, involving a nucleophilic attack of the activated amine group of adenine onto the carbonyl group of lactide, seem to be plausible.

NEW METAL-BASED MICELLES AS ANTICANCER AGENTS

Cancer is a leader cause of death worldwide. One of the problems associated with the current chemotherapeutic options is the noxious side effects caused by the lack of selectivity. In this frame, our research group has been committed to the development of a new Ru and Fe macrometallodrugs.[1] The data obtained so far shows that these compounds present an intrinsic selectivity towards cancer cells (relatively to healthy cells) due to the incorporation of polymeric ligands that promote a passive targeting through the cancer cell membrane. These results prompted us to the development of new macrometallodrugs bearing bioessential metals such as Fe, Zn and Co. We used a ‘M(bipy) 3 ’ scaffold (bipy = 2,2’-bipyridine derivatives) for the synthesis of the new compounds due to the promising cytotoxicity results observed for related compounds.[2] As polymeric ligands we have chosen the polylactide-co-polyethylene glycol amphiphilic copolymer that is able to self-assemble into micelles in water, keeping the metal center hidden, like a Trojan horse. We will present the synthesis and characterization of the new compounds and some preliminary data on their ability to form stable micelles (Figure 1).