Uso de resíduos de queima de casca de café e argila da região sul da Bahia na obtenção de isolador elétrico cerâmico

The electrical ceramic insulators industry, uses noble raw materials such as siliceous and aluminous clays of white burning, in order to provide plasticity of the mass and contribute to electrical and mechanical properties required of the product, and feldspar with the flux function In literature references the composition of the masses indicates that the clay participates in percentage between 20 and 32, and feldspar 8 to 35, these materials have significant cost. In this research was performed the total replacement of commercial clay, for white burning clay from Santa Luzia region in southern Bahia and partial replacement of feldspar by ash residue of husk conilon coffee burning, from extreme south of Bahia. The objective of replacement these raw materials is to aver its technical feasibility and call attention for the embryo pole of ceramic industry for the existing in the south and extreme south of Bahia, which has significant reserves of noble raw materials such as clay white burning, kaolin, quartz and feldspar, and generates significant volume of gray husk conilon coffee as alternate flux. Clay Santa Luzia is prima noble material whose current commercial application is the production of white roofing. The residue of coffee husk ash is discarded near of production sites and is harmful to the environment. Phase diagrams and statistic design of experiments, were used for optimization and cost savings in research. The results confirmed the expectations of obtaining electrical ceramic insulators, with white burning clay of Santa Luzia and partial replacement up to 35.4% of feldspar, by treaty residue of conilon ash coffee husk burning. The statistic design that showed best results was for formulation with percentages of: clay 26.4 to 30.4%; kaolin 14.85 to 17.1%; feldspar 12.92 to 16.96%; R2 residue 7.08 to 9.2% and Quartz 32.5 to 38.75%, relative to the total mass of the mixture. The best results indicated; 0.2 to 1.4% apparent porosity , water absorption 0.1 to 0.7%, flexural strength 35 to 45MPa , dielectric strength 35-41 kV/cm , the transverse resistivity 8x109 2.5x1010 Ω.cm and for the dielectric constant ε/ε0 7 to 10.4, specification parameters for manufacturing ceramic electrical insulators of low and medium voltage.

Prevalência e fatores associados à diminuição da função pulmonar em obesos em pré-operatório de cirurgia bariátrica

Introduction: Obesity shows changes in pulmonary function and respiratory mechanics, however, little is known regarding the prevalence of worsening respiratory function when considering the increase in central or peripheral adiposity or general obesity. Objectives: To analyze the association between anthropometric adiposity and decreased lung function in obese. Materials and Methods: Patients eligible for this study obese individuals (IMC≥30kg/m2) in pre-bariatric surgery and referred for Treatment Clinic of Obesity and Related Diseases, located at the University Hospital Onofre Lopes (HUOL), from October 2005 and July 2014. The evaluation included clinical information and measurement of anthropometric measures (body mass index (BMI), body fat index (BFI) and waist circumference (WC) and neck (NC)) and spirometric. The prevalence and analysis by Poisson regression was performed considering the following outcome variables: forced vital capacity (FVC), forced expiratory volume in one second (FEV1) and Maximum Voluntary Ventilation (MVV) and as predictor variables were considered: BMI, IAC, WC and NC and as control variables: age, gender, smoking history and comorbidities (diabetes mellitus, dyslipidemia and hypertension). Statistical analysis was performed using Statistical Package for Social Sciences software (SPSS - version 20.0). Results: We analyzed 384 individuals, 75% women, mean BMI: 46.6 (± 8.7) kg/m2, IAC: 49.26 (± 9.48)%, WC: 130.84 (± 16.23) cm and NC: 42.3 (± 4.6) cm. The higher prevalence of FVC and FEV1 <80% was observed in individuals with NC above 42 cm, followed those with a BMI above 45 kg/m2. Multivariate analysis using Poisson regression showed as risk factors associated with FVC <80%, the variables: NC above 42 cm (odds ratio (OR) 2.41) and BMI over 45Kg/m2 (OR 1.71 ). As for FEV1 <80% predicted, all predictor variables were associated, with the largest odds presented by the NC (3.40). MVVV was not associated with any studied varaible. Conclusion: Individuals with NC above 42 cm had higher prevalence of reduced lung function and the NC was the measure with the highest association with reduced lung function in obese.

Análise do uso de escalas nas simulações de processos de estampagem

The purpose of using software based on numerical approximations for metal forming is given by the need to ensure process efficiency in order to get high quality products at lowest cost and shortest time. This study uses the theory of similitude in order to develop a technique capable of simulating the stamping process of a metal sheet, obtaining results close to the real values, with shorter processing times. The results are obtained through simulations performed in the finite element software STAMPACK®. This software uses the explicit integration method in time, which is usually applied to solve nonlinear problems involving contact, such as the metal forming processes. The technique was developed from a stamping model of a square box, simulated with four different scale factors, two higher and two smaller than the real scale. The technique was validated with a bending model of a welded plate, which had a high simulation time. The application of the technique allowed over 50% of decrease in the time of simulation. The results for the application of the scale technique for forming plates were satisfactory, showing good quantitative results related to the decrease of the total time of simulation. Finally, it is noted that the decrease in simulation time is only possible with the use of two related scales, the geometric and kinematic scale. The kinematic scale factors should be used with caution, because the high speeds can cause dynamic problems and could influence the results of the simulations.

Métodos de extração de fósforo e micronutrientes em latossolos com uso de energia ultrassônica

Assessing the soil nutrient availability to plants under lab conditions is one of the main challenges to Soil Fertility and Chemistry, due to the complex behavior and the interaction of the soil properties. Many extractant solutions associated with mechanical forms of agitation have been proposed, showing different correlations with plant growth and nutrients absorption. Using ultrasonic energy is a agitation procedure of the soil:extractant solution suspension (based on the cavitation phenomenon). It allows the establishment of relations between the amount of extracted nutrient and the ultrasonic energy level. Thus, this work aims: to evaluate the effect of cavitation intensity on the extraction of P, Zn, Cu, Mn and Fe in soil samples from five Latosols under different uses around Uberlândia and Uberaba, Minas Gerais State; to obtain extracting curves as function of ultrasonic energy levels; and to obtain an index from extracting curves to expresses the nutrient retention by the soil solid phase. A soil-solution suspension (ratio 1:10) was sonicated using a probe ultrasound equipment under different combinations of power and time: i) 30 W for 35, 70, 140 and 280 s; ii) 50 W for 21, 42, 84 and 168 s; and iii) 70 W for 15, 30, 60 and 120 s. The extractant solutions used were Mehlich-1 (for all elements), Olsen and distilled water for P. After each sonication, P concentration was quantified by molybdenum blue colorimetric method and Zn, Cu, Mn and Fe by flame atomic absorption spectrophotometry. The cavitation intensity did not affect the P extraction, only the total energy applied. The P extraction was influenced by extractant solution, decreasing as follows: Mehlich-1>Olsen>water. In cultivated Latosols, the P extraction increased linearly with ultrasonic energy, and the slope of the 1:1 linear regression reflects the P retention in the soil. The Zn and Fe extractions were influenced only by total energy applied. Mn and Cu extractions were influenced by both cavitation intensity and total ultrasonic energy. Soils containing similar amounts of P, Cu, Zn, Mn, and Fe may have a different extraction rate. Likewise, soils containing different amounts of those elements may have the same extraction rate.

Ventilação e prescrições urbanísticas: uma aplicação simulada para a Orla da Praia do Meio em Natal/RN

This work analyses a study on natural ventilation and its relation to the urban legislation versus the building types in an urban fraction of coastal area of Praia do Meio in the city of Natal/RN, approaching the type or types of land use most appropriate to this limited urban fraction. The objective of this study is to analyse the effects of the present legislation as well as the types of buildings in this area on the natural ventilation. This urban fraction was selected because it is one of the sites from where the wind flows into the city of Natal. This research is based on the hypothesis stating that the reduction on the porosity of the urban soil (decrease in the set back/boundary clearance), and an increase in the form (height of the buildings) rise the level of the ventilation gradient, consequently causing a reduction on the wind speed at the lowest part of the buildings. Three-dimensional computational models were used to produce the modes of occupation allowed in the urban fraction within the area under study. A Computational Fluid Dynamics (CFD) software was also used to analyse the modes of land occupation. Following simulation, a statistical assessment was carried out for validation of the hypothesis. It was concluded that the reduction in the soil porosity as a consequence of the rates that defined the minimum boundary clearance between the building and the boundary of the plot (and consequently the set back), as well as the increase in the building form (height of the buildings) caused a reduction in the wind speed, thus creating heat islands

Análise de componentes arquitetônicos para potencialização da ventilação natural com ênfase em captadores de vento

The building envelope is the principal mean of interaction between indoors and environment, with direct influence on thermal and energy performance of the building. By intervening in the envelope, with the proposal of specific architectural elements, it is possible to promote the use of passive strategies of conditioning, such as natural ventilation. The cross ventilation is recommended by the NBR 15220-3 as the bioclimatic main strategy for the hot and humid climate of Natal/RN, offering among other benefits, the thermal comfort of occupants. The analysis tools of natural ventilation, on the other hand, cover a variety of techniques, from the simplified calculation methods to computer fluid dynamics, whose limitations are discussed in several papers, but without detailing the problems encountered. In this sense, the present study aims to evaluate the potential of wind catchers, envelope elements used to increase natural ventilation in the building, through CFD simplified simulation. Moreover, it seeks to quantify the limitations encountered during the analysis. For this, the procedure adopted to evaluate the elements implementation and efficiency was the CFD simulation, abbreviation for Computer Fluid Dynamics, with the software DesignBuilder CFD. It was defined a base case, where wind catchers were added with various settings, to compare them with each other and appreciate the differences in flows and air speeds encountered. Initially there has been done sensitivity tests for familiarization with the software and observe simulation patterns, mapping the settings used and simulation time for each case simulated. The results show the limitations encountered during the simulation process, as well as an overview of the efficiency and potential of wind catchers, with the increase of ventilation with the use of catchers, differences in air flow patterns and significant increase in air speeds indoors, besides changes found due to different element geometries. It is considered that the software used can help designers during preliminary analysis in the early stages of design

Conhecimento das mães acerca do uso da chupeta, amamentação e desenvolvimento da criança

O leite humano é considerado a base da alimentação da criança, porque para além de ser nutritivo ao fornecer-lhe os nutrientes necessários ao seu crescimento, ainda lhe transmite fatores imunológicos e enzimas, protegendo o lactente contra infeções e alergias, bem como facilita o seu desenvolvimento psicossocial. Pedroso (2011, p.40) ao citar Parizotto e Zorzi (2008) refere também que "amamentar é muito mais do que alimentar a criança. Envolve uma interacção complexa, multi-factorial, entre duas pessoas, que interfere no estado nutricional de uma criança, em sua habilidade de se defender de infecções, em sua fisiologia e no seu desenvolvimento cognitivo e emocional". A criança ao mamar, ao sugar o leite materno realiza movimentos musculares a nível da região oral. Ao realizar esses movimentos, a criança obtém uma tonicidade muscular adequada e uma estimulação da estrutura óssea e dos músculos faciais, o que contribui para o correto desenvolvimento dos órgãos fono-articulatórios, prevenindo alterações de hipo-desenvolvimento, mal oclusões e problemas de articulação (Delgado & Halpern, 2005). Pereira (2008) ao citar (Sousa, 1997) refere que a criança durante a amamentação, aprende a respirar corretamente pelo nariz, evitando amigdalites, pneumonias, entre outras doenças. O aleitamento materno proporciona ao bebé um padrão de respiração correto, favorecendo o encerramento labial e a postura adequada da língua, garantindo a boa relação entre as estruturas do Sistema Estomatognático (Tollara et al, 2005), citados por Pereira (2015, p. 15). Cada vez mais as informações veiculadas através dos meios de comunicação social chamam a atenção para a importância da amamentação. No entanto, a promoção comercial desenvolvida pela indústria e empresas do setor podem diminuir a promoção do aleitamento materno, ao oferecerem amostras às mães nas maternidades, o que pode promover o abandono progressivo do aleitamento materno. Segundo Andrezza et al (2013) os bicos de qualquer natureza, quando utilizados por um determinado período, podem causar o fenómeno denominado de confusão de bicos, acabando por levar ao desmame precoce. Um estudo desenvolvido por França et al (2008) referem que o uso da chupeta é um dos determinantes principais que levam as mães a interromper precocemente o aleitamento. O uso da chupeta, referido desde o período neolítico (Castilho e Rocha, 2009), temática controversa, merece a atenção dos vários profissionais de saúde, e é considerado como um problema de Saúde Pública. Pereira (2015) no estudo que desenvolveu concluiu que as crianças que usaram chupeta apresentaram mais alterações na fala, na postura, mobilidade da língua e na mordida comparativamente com as que não a utilizaram. Galvão (2006, p. 25), ao citar a OMS e a UNICEF (1995), afirma que "as práticas adoptadas nos serviços de saúde podem ter um efeito importante sobre a amamentação. Práticas desfavoráveis interferem com a amamentação e contribuem para a disseminação do aleitamento artificial. Boas práticas apoiam o aleitamento materno e favorecem que as mães amamentem com sucesso e continuem a amamentar por longo tempo". Torna-se igualmente importante que as orientações fornecidas pelos profissionais de saúde não sejam diferentes, ambíguas ou contraditórias, pois pode aumentar a ansiedade e angústia das mães. Neste sentido, importa saber: o que sabem as mães que amamentam ou amamentaram sobre a influência do uso da chupeta no processo da amamentação e no desenvolvimento da criança? O que levou as mães que amamentam ou amamentaram a decidir colocar ou não chupeta aos filhos?

Layout, conforto e satisfação dos usuários em escritórios: uma avaliação pós-ocupação no edifício da sede administrativa do INPE-CRN

This research aimed to identify the link between the layout of workspaces in offices and the design strategies for environmental comfort. Strategies surveyed were focused on the thermal, visual and luminic comfort. In this research, visual comfort is related to issues of visual integration within and between the interior and exterior of the building. This is a case study conducted at the administrative headquarters of Centro Regional Nordeste do Instituto de Pesquisas Espaciais (INPE-CRN), located in Natal/RN. The methodological strategy used was the Post-Occupancy Evaluation, which combined the survey data on the building (layout of workspaces, bioclimatic strategies adopted in the design, use of these strategies) with some techniques aimed at acquiring qualitative information related to users. The workspace layout is primordial to satisfaction and productivity of workers. Issues such as concentration, communication, privacy, personal identity, density and space efficiency, barriers (access, visual and even ventilation and lighting), among others, are associated with the layout. The environmental comfort is one of the essential elements to maintaining life quality in workplace. Moreover, it is an important factor in user`s perception of the space in which he or she are inserted. Both layout and environmental comfort issues should be collected and analyzed in the establishment phase of the programming step. That way, it is possible to get adequate answers to these questions in subsequent project phases. It was found that changes in the program that occurred over time, especially concerning persons (number and characteristics), resulted in changes in layout, generating high density and inflexible environments. It turns difficult to adjust the furniture to the occupants` requirement, including comfort needs. However, the presence of strategies for environmental quality provides comfort to spaces, ensuring that, even in situations not considered optimal, users perceive the environment in a positive way. It was found that the relationship between environmental comfort and layout takes the following forms: in changing the perception of comfort, depending on the layout of the arrangements; adjustments in layout, due to needs for comfort; and the elevation of user satisfaction and environmental quality due to the presence of strategies comfort even in situations of inadequate layout

Ventilação e prescrições urbanísticas: uma aplicação simulada no bairro de Petrópolis em Natal/RN

The present work studies the natural ventilation and its relationship with the urban standards, which establishes the form of occupation and use of the land in our cities. The method simulates the application of the urban standards of the City Master Plan over the last three years. The simulation takes place in the District of Petrópolis, in the city of Natal , Brazil and analyses the effects of the standards of natural ventilation. The formulated hypothesis states that the reductions in the urban spaces between buildings rises up the vertical profile of ventilation, reducing, therefore, the velocity of the wind at the lower levels of the buildings. To develop the study, occupation models were built, using computerized, three-dimensional models. These occupation models were analyzed using the CFD (Computational Fluid Dynamics) code. The conclusion is that the more we reduce the urban space between buildings, the more we reduce the wind speed in constructed areas, increasing, therefore, the possibility to generate heat islands

Diseño y construcción de un banco de refrigeración por absorción para uso didáctico, utilizando Agua y Sales de Bromuro de Litio

En este trabajo de graduación se presenta paso a paso, el diseño y construcción de una unidad de laboratorio que permite familiarizarse con los principios, y la demostración de la refrigeración por absorción para uso didáctico, utilizando agua como refrigerante y sales de bromuro de litio como absorbente, enfatizando en las ventajas e inconvenientes que este tipo de equipos presenta comparado con el sistema de refrigeración por compresión de vapor; como un insumo a la Facultad de Ingeniería y Arquitectura de la Universidad de El Salvador, fomentando el uso de energías renovables y el uso eficiente de los recursos energéticos. Se muestra el detalle del método de diseño y fabricación de cada componente del sistema, los materiales utilizados, planos constructivos y costos de fabricación. Las guías de laboratorio como una serie de pasos para impulsar en la comunidad estudiantil de la facultad la formación en el área, y un manual de operaciones para hacer correcto uso del banco de refrigeración por absorción, además de una manipulación segura y responsable de las sustancias de trabajo

Simulação em uso dos pisos de madeira de Eucalyptus sp e Corymbia maculata

A caracterização anatômica, física, mecânica e química da madeira fornece informações importantes para sua melhor utilização. Contudo, para que madeiras se tornem boa opção para o mercado de pisos, adicionalmente é necessária a realização de ensaios que simulem suas reais condições em serviço. Esses ensaios simulam o pisoteio executado pelos sapatos de salto com pequenas áreas de pressão, o arraste e a queda de objetos, a resistência à abrasão da superfície e o atrito oferecido durante o deslocamento de pessoas que caminham sobre ele. Grande dificuldade da seleção de novas madeiras para pisos está na ausência de valores de referência físico-mecânicos. O presente trabalho visou a caracterizar as madeiras de Eucalyptus clöeziana F. Muell, de Eucalyptus microcorys F. Muell e de Corymbia maculata Hook, para as propriedades de densidade básica, retratibilidade, aplicação de carga rolante, de atrito estático e dinâmico, endentação causada por cargas aplicadas em pequenas áreas, impacto da esfera de aço cadente e resistência à abrasão. Foi observado que as madeiras estudadas podem ser utilizadas para a confecção de pisos, de acordo com seus resultados obtidos e por meio de comparações com resultados de literatura.

Caracterização termo-mecânica de interconectores metálicos recobertos com filmes de LaCrO3

The cells unitaria of the solid oxide fuel cell are separated by means of interconnects, which serve as electrical contact between the cells. Lanthanum Chromite (LaCrO3) has been the most common material used as interconnect in solid oxide fuel cells. Reducing the operating temperature around 800 º C of cells to solid oxide fuel make possibilite the use of metallic interconnects as an alternative to ceramic LaCrO3. Metallic interconnects have advantages over ceramic interconnects such as high thermal conductivity, electricity, good ductility, low cost, good physical and mechanical properties. In this work evaluate the thermo-mechanical properties of the metallic substrate and coated metallic substrate with the ceramic LaCrO3 film via spray-pyrolysis, in order to demonstrate the feasibility of using this material as a component of a fuel cell solid oxide. The materials were characterized by X-ray diffraction, oxidation behavior, mechanical strength, optical microscopy (OM) and scanning electron microscopy (SEM). The X-ray diffraction proved the formation phase of the LaCrO3 on the metallic substrate and the identification of the phases formed after the oxidative test and mechanical strength at high temperature. The oxidation behavior showed the increased oxidation resistance of the coated metallic substrate. It was noted that the mechanical resistance to bending of the coated metallic substrate only increases at room temperature. The optical microscopy (OM) has provided an assessment of both the metallic substrate and the LaCrO3 film deposited on the metal substrate that, in comparison with the micrographs obtained from SEM. The SEM one proved the formation of Cr2O3 layer on the metallic substrate and stability of LaCrO3 film after oxidative test, it can also observe the displacement of the ceramic LaCrO3 film after of mechanical testing and mapping of the main elements as chromium, manganese, oxygen, lanthanum in samples after the thermo-mechanical tests.

Análisis de los conceptos del movimiento vibracional y sonido con el uso de las TIC's

Los sonidos y vibraciones de estas toman una importancia muy grande en nuestras vidas, nos ayudan a estar más atentos y a comunicarnos a diario, un mundo sin sonidos no hubiera funcionado de la misma manera ya que ha sido parte en descubrir cosas grandes .A diario nos comunicamos por medio de comunicación verbal que es transmitida atreves de ondas invisibles que escuchamos a través de nuestros oídos que conocemos como sonidos. El timbre de un sonido es aquello que nos permite distinguir la voz de dos personas que cantan una misma canción, o bien diferentes instrumentos que emiten una misma nota musical. Longitud de onda: La distancia existente entre dos crestas o valles consecutivos es lo que llamamos longitud de onda. La reflexión es una propiedad de la propagación del sonido, junto con la atenuación, dispersión, absorción y la refracción. Todo el mundo suele tener claro lo que significa la reflexión de una onda. Este fenómeno, que se aprecia muy claramente con la luz en un espejo, se produce de igual forma con el sonido. Cuando el sonido tropieza con un obstáculo, lo que hace la mayor parte de la energía de la onda, es cambiar de fase y volver por el mismo camino por el que ha llegado, pero en sentido contrario.

Facilitador de enfermera con el uso de aplicaciones móviles

El proyecto Facilitador de Enfermera (F.E) es un servicio que estará disponible en todo momento para los estudiantes de la Facultad de Enfermería en sus celulares, esta aplicación ayudara a cumplir las necesidades de los alumnos de poder obtener la información correcta de terminología médica y de fórmulas para la implantación de medicamentos que necesitan para sus materias dentro de la facultad y para ofrecer un mejor servicio a los pacientes en donde ellos estén haciendo su servicio o prácticas profesionales. Con esta aplicación los alumnos ahorraran tiempo de investigación, ofrecerán un servicio eficiente y rápido a los pacientes ya que lo tendrán siempre en mano sin necesidad de moverse de donde están, solamente necesitaran abrir la aplicación y a través del menú podrán elegir lo que desean y listo, podrán ver cuanta solución de agua necesitan los medicamentos para ser inyectados, la descripción del medicamento y como aplicar dicho medicamento, además contendrá un diccionario con la descripción de los diferentes medicamentos. En esta aplicación no se utilizó un sistema de usuario y contraseña ya que perdería tiempo y requeriría un servicio de internet, se trata que la aplicación sea lo más rápida posible y siempre accesible, se utilizó programación Android para sistemas móviles, la aplicación acepta desde la versión 1.6 hasta la 4.7 y se utilizó un sistemas en línea llamada Appinventor2 creada por la MIT de E.U. para su creación rápida y segura.

Síntese verde de nanopartículas de prata a partir de extrato aquoso do tubérculo de Curcuma longa associadas à quitosana e avaliação da atividade antitumoral in vitro em câncer de pele não melanoma (linhagem A431)

Dissertação (mestrado)—Universidade de Brasília, Instituto de Ciências Biológicas, Programa de Pós-Graduação Nanociência e Nanobiotecnologia, 2016.