Sensitivity of peak positions to flight-path parameters in a deep-inelastic scattering neutron TOF spectrometer

The effects of small changes in flight-path parameters (primary and secondary flight paths, detector angles), and of displacement of the sample along the beam axis away from its ideal position, are examined for an inelastic time-of-flight (TOF) neutron spectrometer, emphasising the deep-inelastic regime. The aim was to develop a rational basis for deciding what measured shifts in the positions of spectral peaks could be regarded as reliable in the light of the uncertainties in the calibrated flight-path parameters. Uncertainty in the length of the primary or secondary flight path has the least effect on the positions of the peaks of H, D and He, which are dominated by the accuracy of the calibration of the detector angles. This aspect of the calibration of a TOF spectrometer therefore demands close attention to achieve reliable outcomes where the position of the peaks is of significant scientific interest and is discussed in detail. The corresponding sensitivities of the position of peak of the Compton profile, J(y), to flight-path parameters and sample position are also examined, focusing on the comparability across experiments of results for H, D and He. We show that positioning the sample to within a few mm of the ideal position is required to ensure good comparability between experiments if data from detectors at high forward angles are to be reliably interpreted.

Experimental investigation of the governing parameters in the electrospinning of poly(3-hydroxybutyrate) scaffolds : structural characteristics of the pores

We sought to determine the impact of electrospinning parameters on a trustworthy criterion that could evidently improve the maximum applicability of fibrous scaffolds for tissue regeneration. We used an image analysis technique to elucidate the web permeability index (WPI) by modeling the formation of electrospun scaffolds. Poly(3-hydroxybutyrate) (P3HB) scaffolds were fabricated according to predetermined conditions of levels in a Taguchi orthogonal design. The material parameters were the polymer concentration, conductivity, and volatility of the solution. The processing parameters were the applied voltage and nozzle-to-collector distance. With a law to monitor the WPI values when the polymer concentration or the applied voltage was increased, the pore interconnectivity was decreased. The quality of the jet instability altered the pore numbers, areas, and other structural characteristics, all of which determined the scaffold porosity and aperture interconnectivity. An initial drastic increase was observed in the WPI values because of the chain entanglement phenomenon above a 6 wt % P3HB content. Although the solution mixture significantly (p < 0.05) changed the scaffold architectural characteristics as a function of the solution viscosity and surface tension, it had a minor impact on the WPI values. The solution mixture gained the third place of significance, and the distance was approved as the least important factor.

The feral horse foot. Part B : radiographic, gross visual and histopathological parameters of foot health in 100 Australian feral horses

Background It has been proposed that the feral horse foot is a benchmark model for foot health in horses. However, the foot health of feral horses has not been formally investigated. Objectives To investigate the foot health of Australian feral horses and determine if foot health is affected by environmental factors, such as substrate properties and distance travelled. Methods Twenty adult feral horses from five populations (n = 100) were investigated. Populations were selected on the basis of substrate hardness and the amount of travel typical for the population. Feet were radiographed and photographed, and digital images were surveyed by two experienced assessors blinded to each other's assessment and to the population origin. Lamellar samples from 15 feet from three populations were investigated histologically for evidence of laminitis. Results There was a total of 377 gross foot abnormalities identified in 100 left forefeet. There were no abnormalities detected in three of the feet surveyed. Each population had a comparable prevalence of foot abnormalities, although the type and severity of abnormality varied among populations. Of the three populations surveyed by histopathology, the prevalence of chronic laminitis ranged between 40% and 93%. Conclusions Foot health appeared to be affected by the environment inhabited by the horses. The observed chronic laminitis may be attributable to either nutritional or traumatic causes. Given the overwhelming evidence of suboptimal foot health, it may not be appropriate for the feral horse foot to be the benchmark model for equine foot health.

Teachers’ knowledge of anxiety and identification of excessive anxiety in children

This study examined primary school teachers’ knowledge of anxiety and excessive anxiety symptoms in children. Three hundred and fifteen primary school teachers completed a questionnaire exploring their definitions of anxiety and the indications they associated with excessive anxiety in primary school children. Results showed that teachers had an understanding of what anxiety was in general but did not consistently distinguish normal anxiety from excessive anxiety, often defining all anxiety as a negative experience. Teachers were able to identify symptoms of excessive anxiety in children by recognizing anxiety-specific and general problem indications. The results provided preliminary evidence that teachers’ knowledge of anxiety and anxiety disorders does not appear to be a barrier in preventing children’s referrals for mental health treatment. Implications for practice and directions for future research are discussed.

A quasi-maximum likelihood method for estimating the parameters of multivariate diffusions

A quasi-maximum likelihood procedure for estimating the parameters of multi-dimensional diffusions is developed in which the transitional density is a multivariate Gaussian density with first and second moments approximating the true moments of the unknown density. For affine drift and diffusion functions, the moments are exactly those of the true transitional density and for nonlinear drift and diffusion functions the approximation is extremely good and is as effective as alternative methods based on likelihood approximations. The estimation procedure generalises to models with latent factors. A conditioning procedure is developed that allows parameter estimation in the absence of proxies.

Identification of symptom clusters in patients with chronic venous leg ulcers

Context Patients with venous leg ulcers experience multiple symptoms, including pain, depression, and discomfort from lower leg inflammation and wound exudate. Some of these symptoms impair wound healing and decrease quality of life (QOL). The presence of co-occurring symptoms may have a negative effect on these outcomes. The identification of symptom clusters could potentially lead to improvements in symptom management and QOL. Objectives To identify the prevalence and severity of common symptoms and the occurrence of symptom clusters in patients with venous leg ulcers. Methods For this secondary analysis, data on sociodemographic characteristics, medical history, venous history, ulcer and lower limb clinical characteristics, symptoms, treatments, healing, and QOL were analyzed from a sample of 318 patients with venous leg ulcers who were recruited from hospital outpatient and community nursing clinics for leg ulcers. Exploratory factor analysis was used to identify symptom clusters. Results Almost two-thirds (64%) of the patients experienced four or more concurrent symptoms. The most frequent symptoms were sleep disturbance (80%), pain (74%), and lower limb swelling (67%). Sixty percent of patients reported three or more symptoms at a moderate-to-severe level of intensity (e.g., 78% reported disturbed sleep frequently or always; the mean pain severity score was 49 of 100, SD 26.5). Exploratory factor analysis identified two symptom clusters: pain, depression, sleep disturbance, and fatigue; and swelling, inflammation, exudate, and fatigue. Conclusion Two symptom clusters were identified in this sample of patients with venous leg ulcers. Further research is needed to verify these symptom clusters and to evaluate their effect on patient outcomes.

Identification and evaluation of service bundles for governmental one-stop portals

Recent advances in the area of ‘Transformational Government’ position the citizen at the centre of focus. This paradigm shift from a department-centric to a citizen-centric focus requires governments to re-think their approach to service delivery, thereby decreasing costs and increasing citizen satisfaction. The introduction of franchises as a virtual business layer between the departments and their citizens is intended to provide a solution. Franchises are structured to address the needs of citizens independent of internal departmental structures. For delivering services online, governments pursue the development of a One-Stop Portal, which structures information and services through those franchises. Thus, each franchise can be mapped to a specific service bundle, which groups together services that are deemed to be of relevance to a specific citizen need. This study focuses on the development and evaluation of these service bundles. In particular, two research questions guide the line of investigation of this study: Research Question 1): What methods can be used by governments to identify service bundles as part of governmental One-Stop Portals? Research Question 2): How can the quality of service bundles in governmental One-Stop Portals be evaluated? The first research question asks about the identification of suitable service bundle identification methods. A literature review was conducted, to, initially, conceptualise the service bundling task, in general. As a consequence, a 4-layer model of service bundling and a morphological box were created, detailing characteristics that are of relevance when identifying service bundles. Furthermore, a literature review of Decision-Support Systems was conducted to identify approaches of relevance in different bundling scenarios. These initial findings were complemented by targeted studies of multiple leading governments in the e-government domain, as well as with a local expert in the field. Here, the aim was to identify the current status of online service delivery and service bundling in practice. These findings led to the conceptualising of two service bundle identification methods, applicable in the context of Queensland Government: On the one hand, a provider-driven approach, based on service description languages, attributes, and relationships between services was conceptualised. As well, a citizen-driven approach, based on analysing the outcomes from content identification and grouping workshops with citizens, was also conceptualised. Both methods were then applied and evaluated in practice. The conceptualisation of the provider-driven method for service bundling required the initial specification of relevant attributes that could be used to identify similarities between services called relationships; these relationships then formed the basis for the identification of service bundles. This study conceptualised and defined seven relationships, namely ‘Co-location’, ‘Resource’, ‘Co-occurrence’, ‘Event’, ‘Consumer’, ‘Provider’, and ‘Type’. The relationships, and the bundling method itself, were applied and refined as part of six Action Research cycles in collaboration with the Queensland Government. The findings show that attributes and relationships can be used effectively as a means for bundle identification, if distinct decision rules are in place to prescribe how services are to be identified. For the conceptualisation of the citizen-driven method, insights from the case studies led to the decision to involve citizens, through card sorting activities. Based on an initial list of services, relevant for a certain franchise, participating citizens grouped services according to their liking. The card sorting activity, as well as the required analysis and aggregation of the individual card sorting results, was analysed in depth as part of this study. A framework was developed that can be used as a decision-support tool to assist with the decision of what card sorting analysis method should be utilised in a given scenario. The characteristic features associated with card sorting in a government context led to the decision to utilise statistical analysis approaches, such as cluster analysis and factor analysis, to aggregate card sorting results. The second research question asks how the quality of service bundles can be assessed. An extensive literature review was conducted focussing on bundle, portal, and e-service quality. It was found that different studies use different constructs, terminology, and units of analysis, which makes comparing these models a difficult task. As a direct result, a framework was conceptualised, that can be used to position past and future studies in this research domain. Complementing the literature review, interviews conducted as part of the case studies with leaders in e-government, indicated that, typically, satisfaction is evaluated for the overall portal once the portal is online, but quality tests are not conducted during the development phase. Consequently, a research model which appropriately defines perceived service bundle quality would need to be developed from scratch. Based on existing theory, such as Theory of Reasoned Action, Expectation Confirmation Theory, and Theory of Affordances, perceived service bundle quality was defined as an inferential belief. Perceived service bundle quality was positioned within the nomological net of services. Based on the literature analysis on quality, and on the subsequent work of a focus group, the hypothesised antecedents (descriptive beliefs) of the construct and the associated question items were defined and the research model conceptualised. The model was then tested, refined, and finally validated during six Action Research cycles. Results show no significant difference in higher quality or higher satisfaction among users for either the provider-driven method or for the citizen-driven method. The decision on which method to choose, it was found, should be based on contextual factors, such as objectives, resources, and the need for visibility. The constructs of the bundle quality model were examined. While the quality of bundles identified through the citizen-centric approach could be explained through the constructs ‘Navigation’, ‘Ease of Understanding’, and ‘Organisation’, bundles identified through the provider-driven approach could be explained solely through the constructs ‘Navigation’ and ‘Ease of Understanding’. An active labelling style for bundles, as part of the provider-driven Information Architecture, had a larger impact on ‘Quality’ than the topical labelling style used in the citizen-centric Information Architecture. However, ‘Organisation’, reflecting the internal, logical structure of the Information Architecture, was a significant factor impacting on ‘Quality’ only in the citizen-driven Information Architecture. Hence, it was concluded that active labelling can compensate for a lack of logical structure. Further studies are needed to further test this conjecture. Such studies may involve building alternative models and conducting additional empirical research (e.g. use of an active labelling style for the citizen-driven Information Architecture). This thesis contributes to the body of knowledge in several ways. Firstly, it presents an empirically validated model of the factors explaining and predicting a citizen’s perception of service bundle quality. Secondly, it provides two alternative methods that can be used by governments to identify service bundles in structuring the content of a One-Stop Portal. Thirdly, this thesis provides a detailed narrative to suggest how the recent paradigm shift in the public domain, towards a citizen-centric focus, can be pursued by governments; the research methodology followed by this study can serve as an exemplar for governments seeking to achieve a citizen-centric approach to service delivery.

Development of optimal designs of insulated rail joints

Proper functioning of Insulated Rail Joints (IRJs) is essential for the safe operation of the railway signalling systems and broken rail identification circuitries. The Conventional IRJ (CIRJ) resembles structural butt joints consisting of two pieces of rails connected together through two joint bars on either side of their web and the assembly is held together through pre-tensioned bolts. As the IRJs should maintain electrical insulation between the two rails, a gap between the rail ends must be retained at all times and all metal contacting surfaces should be electrically isolated from each other using non-conductive material. At the gap, the rail ends lose longitudinal continuity and hence the vertical sections of the rail ends are often severely damaged, especially at the railhead, due to the passage of wheels compared to other continuously welded rail sections. Fundamentally, the reason for the severe damage can be related to the singularities of the wheel-rail contact pressure and the railhead stress. No new generation designs that have emerged in the market to date have focussed on this fundamental; they only have provided attention to either the higher strength materials or the thickness of the sections of various components of the IRJs. In this thesis a novel method of shape optimisation of the railhead is developed to eliminate the pressure and stress singularities through changes to the original sharp corner shaped railhead into an arc profile in the longitudinal direction. The optimal shape of the longitudinal railhead profile has been determined using three nongradient methods in search of accuracy and efficiency: (1) Grid Search Method; (2) Genetic Algorithm Method and (3) Hybrid Genetic Algorithm Method. All these methods have been coupled with a parametric finite element formulation for the evaluation of the objective function for each iteration or generation depending on the search algorithm employed. The optimal shape derived from these optimisation methods is termed as Stress Minimised Railhead (SMRH) in this thesis. This optimal SMRH design has exhibited significantly reduced stress concentration that remains well below the yield strength of the head hardened rail steels and has shifted the stress concentration location away from the critical zone of the railhead end. The reduction in the magnitude and the relocation of the stress concentration in the SMRH design has been validated through a full scale wheel – railhead interaction test rig; Railhead strains under the loaded wheels have been recorded using a non-contact digital image correlation method. Experimental study has confirmed the accuracy of the numerical predications. Although the SMRH shaped IRJs eliminate stress singularities, they can still fail due to joint bar or bolt hole cracking; therefore, another conceptual design, termed as Embedded IRJ (EIRJ) in this thesis, with no joint bars and pre-tensioned bolts has been developed using a multi-objective optimisation formulation based on the coupled genetic algorithm – parametric finite element method. To achieve the required structural stiffness for the safe passage of the loaded wheels, the rails were embedded into the concrete of the post tensioned sleepers; the optimal solutions for the design of the EIRJ is shown to simplify the design through the elimination of the complex interactions and failure modes of the various structural components of the CIRJ. The practical applicability of the optimal shapes SMRH and EIRJ is demonstrated through two illustrative examples, termed as improved designs (IMD1 & IMD2) in this thesis; IMD1 is a combination of the CIRJ and the SMRH designs, whilst IMD2 is a combination of the EIRJ and SMRH designs. These two improved designs have been simulated for two key operating (speed and wagon load) and design (wheel diameter) parameters that affect the wheel-rail contact; the effect of these parameters has been found to be negligible to the performance of the two improved designs and the improved designs are in turn found far superior to the current designs of the CIRJs in terms of stress singularities and deformation under the passage of the loaded wheels. Therefore, these improved designs are expected to provide longer service life in relation to the CIRJs.

Damage identification and condition assessment of building structures using frequency response functions and neural networks

This thesis investigated the viability of using Frequency Response Functions in combination with Artificial Neural Network technique in damage assessment of building structures. The proposed approach can help overcome some of limitations associated with previously developed vibration based methods and assist in delivering more accurate and robust damage identification results. Excellent results are obtained for damage identification of the case studies proving that the proposed approach has been developed successfully.

Effects of free flow state highway traffic parameters on the performance of amplify and forward cooperative multi-hop vehicular networks

In this paper we analyse the effects of highway traffic flow parameters like vehicle arrival rate and density on the performance of Amplify and Forward (AF) cooperative vehicular networks along a multi-lane highway under free flow state. We derive analytical expressions for connectivity performance and verify them with Monte-Carlo simulations. When AF cooperative relaying is employed together with Maximum Ratio Combining (MRC) at the receivers the average route error rate shows 10-20 fold improvement compared to direct communication. A 4-8 fold increase in maximum number of traversable hops can also be observed at different vehicle densities when AF cooperative communication is used to strengthen communication routes. However the theorical upper bound of maximum number of hops promises higher performance gains.

Identification of molecular genetic factors that influence migraine

Migraine is a common neurological disorder with a strong genetic basis. However, the complex nature of the disorder has meant that few genes or susceptibility loci have been identified and replicated consistently to confirm their involvement in migraine. Approaches to genetic studies of the disorder have included analysis of the rare migraine subtype, familial hemiplegic migraine with several causal genes identified for this severe subtype. However, the exact genetic contributors to the more common migraine subtypes are still to be deciphered. Genome-wide studies such as genome-wide association studies and linkage analysis as well as candidate genes studies have been employed to investigate genes involved in common migraine. Neurological, hormonal and vascular genes are all considered key factors in the pathophysiology of migraine and are a focus of many of these studies. It is clear that the influence of individual genes on the expression of this disorder will vary. Furthermore, the disorder may be dependent on gene–gene and gene–environment interactions that have not yet been considered. In addition, identifying susceptibility genes may require phenotyping methods outside of the International Classification of Headache Disorders II criteria, such as trait component analysis and latent class analysis to better define the ambit of migraine expression.

A molecular genetic approach for forensic animal species identification

This study investigated potential markers within chromosomal, mitochondrial DNA (mtDNA) and ribosomal RNA (rRNA) with the aim of developing a DNA based method to allow differentiation between animal species. Such discrimination tests may have important applications in the forensic science, agriculture, quarantine and customs fields. DNA samples from five different animal individuals within the same species for 10 species of animal (including human) were analysed. DNA extraction and quantitation followed by PCR amplification and GeneScan visualisation formed the basis of the experimental analysis. Five gene markers from three different types of genes were investigated. These included genomic markers for the β-actin and TP53 tumor suppressor gene. Mitochondrial DNA markers, designed by Bataille et al. [Forensic Sci. Int. 99 (1999) 165], examined the Cytochrome b gene and Hypervariable Displacement Loop (D-Loop) region. Finally, a ribosomal RNA marker for the 28S rRNA gene optimised by Naito et al. [J. Forensic Sci. 37 (1992) 396] was used as a possible marker for speciation. Results showed a difference of only several base pairs between all species for the β-actin and 28S markers, with the exception of Sus scrofa (pig) β-actin fragment length, which produced a significantly smaller fragment. Multiplexing of Cytochrome b and D-Loop markers gave limited species information, although positive discrimination of human DNA was evident. The most specific and discriminatory results were shown using the TP53 gene since this marker produced greatest fragment size differences between animal species studied. Sample differentiation for all species was possible following TP53 amplification, suggesting that this gene could be used as a potential animal species identifier.

Identification and simultaneous analysis of harmane, harmol, isovitexin and vitexin in Passiflora incarnata extracts with a novel HLPC method

A high performance liquid chromatographic method for the simultaneous analysis of two flavonoids (iso-vitexin and vitexin), and three indole alkaloids (harmane, harmine, and harmol) was developed. This method was then utilised to quantitate levels of these five constituents in methanolic extracts of Australian Passiflora incarnata. HPLC analysis was performed using a Waters™ Novapak C18 (150 × 4 mm, 4 μm) column, with a gradient solvent system of methanol-water-acetic acid. Detection was achieved by PDA UV (254 nm) and fluorescence (excitation 254 nm, emission 414 nm), utilising the external standard method to obtain quantification.

Impact of a school-based food garden on attitudes and identification skills regarding vegetables and fruit : a 12-month intervention trial

Objective To determine changes in ability to identify specific vegetables and fruits, and attitudes towards vegetables and fruit, associated with the introduction of a school-based food garden. Design A 12-month intervention trial using a historical control (control n 132, intervention n 120), class-based, self-administered questionnaires requiring one-word answers and 3-point Likert scale responses. Setting A state primary school (grades 4 to 7) in a low socio-economic area of Brisbane, Australia. Intervention The introduction of a school-based food garden, including the funding of a teacher coordinator for 11 h/week to facilitate integration of garden activities into the curriculum. Main outcome measures Ability to identify a series of vegetables and fruits, attitudes towards vegetables and fruit. Analysis Frequency distributions for each item were generated and χ2 analyses were used to determine statistical significance. Exploratory factor analysis was employed to detect major trends in data. Results The intervention led to enhanced ability to identify individual vegetables and fruits, greater attention to origins of produce (garden-grown and fresh), changes to perceived consumption of vegetables and fruits, and enhanced confidence in preparing fruit and vegetable snacks, but decreased interest in trying new fruits. Conclusions The introduction of this school-based food garden was associated with skill and attitudinal changes conducive to enhancing vegetable and fruit consumption. The ways in which such changes might impact on dietary behaviours and intake require further analysis.

Human identification at a distance using iris and face

This research has successfully applied super-resolution and multiple modality fusion techniques to address the major challenges of human identification at a distance using face and iris. The outcome of the research is useful for security applications.