Adaptive regulation of vector-controlled induction motors

This paper addresses the speed and flux regulation of induction motors under the assumption that the motor parameters are poorly known. An adaptive passivity-based control is proposed that guarantees robust regulation as well as accurate estimation of the electrical parameters that govern the motor performance. This paper provides a local stability analysis of the adaptive scheme, which is illustrated by simulations and supported by a successful experimental validation on an industrial product. © 2009 IEEE.

Rhythmic feedback control of a blind planar juggler

The paper considers the feedback stabilization of periodic orbits in a planar juggler. The juggler is "blind," i.e, he has no other sensing capabilities than the detection of impact times. The robustness analysis of the proposed control suggests that the arms acceleration at impact is a crucial design parameter even though it plays no role in the stability analysis. Analytical results and convergence proofs are provided for a simplified model of the juggler. The control law is then adapted to a more accurate model and validated in an experimental setup. © 2007 IEEE.

Synchronization and balancing on the N-torus

In this paper, we study the behavior of a network of N agents, each evolving on the circle. We propose a novel algorithm that achieves synchronization or balancing in phase models under mild connectedness assumptions on the (possibly time-varying and unidirectional) communication graphs. The global convergence analysis on the N-torus is a distinctive feature of the present work with respect to previous results that have focused on convergence in the Euclidean space. © 2006 Elsevier B.V. All rights reserved.

Feedback control of impact dynamics: The bouncing ball revisited

We study the the design of a tracking controller for the popular bouncing ball model: the continuous-time actuation of a table is used to control the impacts of the table with a bouncing ball. The proposed control law uses the impact times as the sole feedback information. We show that the acceleration of the table at impact plays no role in the stability analysis but is an important parameter for the robustness of the feedback system to model uncertainty, in particular to the uncertainty on the coefficient of restitution. © 2006 IEEE.

A perturbation approach to the stabilization of nonlinear cascade systems with time-delay

The effect of bounded input perturbations on the stability of nonlinear globally asymptotically stable delay differential equations is analyzed. We investigate under which conditions global stability is preserved and if not, whether semi-global stabilization is possible by controlling the size or shape of the perturbation. These results are used to study the stabilization of partially linear cascade systems with partial state feedback.

Friction-induced vibration: Model development and comparison with large-scale experimental tests

This paper presents a comparison between theoretical predictions and experimental results from a pin-on-disc test rig exploring friction-induced vibration. The model is based on a linear stability analysis of two systems coupled by sliding contact at a single point. Predictions are compared with a large volume of measured squeal initiations that have been post-processed to extract growth rates and frequencies at the onset of squeal. Initial tests reveal the importance of including both finite contact stiffness and a velocity-dependent dynamic model for friction, giving predictions that accounted for nearly all major clusters of squeal initiations from 0 to 5 kHz. However, a large number of initiations occurred at disc mode frequencies that were not predicted with the same parameters. These frequencies proved remarkably difficult to destabilise, requiring an implausibly high coefficient of friction. An attempt has been made to estimate the dynamic friction behaviour directly from the squeal initiation data, revealing complex-valued frequency-dependent parameters for a new model of linearised dynamic friction. These new parameters readily destabilised the disc modes and provided a consistent model that could account for virtually all initiations from 0 to 15 kHz. The results suggest that instability thresholds for a wide range of squeal-type behaviour can be predicted, but they highlight the central importance of a correct understanding and accurate description of dynamic friction at the sliding interface. © 2013 Elsevier Ltd. All rights reserved.

What kind of friction model is needed to predict brake squeal?

Predictive models of friction-induced vibration have proved elusive despite decades of research. There are many mechanisms that can cause brake squeal; friction coupled systems can be highly sensitive to small perturbations; and the dynamic properties of friction at the contact zone seem to be poorly understood. This paper describes experimental and theoretical work aimed at identifying the key ingredients of a predictive model. A large-scale experiment was carried out to identify squeal initiations using a pin-on-disc test rig: approximately 30,000 squeal initiations were recorded, covering a very wide range of frequencies. The theoretical model allows for completely general linear systems coupled at a single sliding point by friction: squeal is predicted using a linearised stability analysis. Results will be presented that show that almost all observed squeal events can be predicted within this model framework, but that some subsets require innovative friction modelling: predictions are highly dependent on the particular choice of friction model and its associated parameters. Copyright © 2012 by ASME.

What kind of friction model is needed to predict brake squeal?

Predictive models of friction-induced vibration have proved elusive despite decades of research. There are many mechanisms that can cause brake squeal; friction coupled systems can be highly sensitive to small perturbations; and the dynamic properties of friction at the contact zone seem to be poorly understood. This paper describes experimental and theoretical work aimed at identifying the key ingredients of a predictive model. A large-scale experiment was carried out to identify squeal initiations using a pin-on-disc test rig: approximately 30,000 squeal initiations were recorded, covering a very wide range of frequencies. The theoretical model allows for completely general linear systems coupled at a single sliding point by friction: squeal is predicted using a linearised stability analysis. Results will be presented that show that almost all observed squeal events can be predicted within this model framework, but that some subsets require innovative friction modelling: predictions are highly dependent on the particular choice of friction model and its associated parameters. Copyright © 2012 by ASME.

Predictive optimisation of high-power IGBT switching under Active Voltage Control

Active Voltage Control (AVC) is an implementation of classic Proportional-Derivative (PD) control and multi-loop feedback control to force IGBT to follow a pre-set switching trajectory. The initial objective of AVC was mainly to synchronise the switching of IGBTs connected in series so as to realise voltage balancing between devices. For a single IGBT switching, the AVC reference needs further optimisation. Thus, a predictive manner of AVC reference generation is required to cope with the nonlinear IGBT switching parameters while performing low loss switching. In this paper, an improved AVC structure is adopted along with a revised reference which accommodates the IGBT nonlinearity during switching and is predictive based on current being switched. Experimental and simulation results show that close control of a single IGBT switching is realised. It is concluded that good performance can be obtained, but the proposed method needs careful stability analysis for parameter choice. © 2013 IEEE.

Adaptive combustion instability control with saturation

The control of a class of combustion systems, suceptible to damage from self-excited combustion oscillations, is considered. An adaptive stable controller, called Self-Tuning Regulator (STR), has recently been developed, which meets the apparently contradictory challenge of relying as little as possible on a particular combustion model while providing some guarantee that the controller will cause no harm. The controller injects some fuel unsteadily into the burning region, thereby altering the heat release, in response to an input signal detecting the oscillation. This paper focuses on an extension of the STR design, when, due to stringent emission requirements and to the danger of flame extension, the amount of fuel used for control is limited in amplitude. A Lyapunov stability analysis is used to prove the stability of the modified STR when the saturation constraint is imposed. The practical implementation of the modified STR remains straightforward, and simulation results, based on the nonlinear premixed flame model developed by Dowling, show that in the presence of a saturation constraint, the self-excited oscillations are damped more rapidly with the modified STR than with the original STR. © 2001 by S. Evesque. Published by the American Institute of Aeronautics and Astronautics, Inc.

强地震荷载作用下含断层岩质边坡稳定性分析

基于岩石材料的弹塑性损伤理论, 引入两个独立的损伤变量分别控制岩石的拉压行为, 通过对地震菏载作用下边坡场地响应的有限元数值模拟, 总结含裂隙的岩质边坡发生局部损伤软化、破坏的仄域的扩展、演化过程和规律.结合对某大型水电坝坝址左岸的岩质边坡在强地震动载荷作用下(百年一遇、超越概率 2%)发生破坏的数值模拟, 揭示这类边坡滑坡的机理, 并根据模拟的结果, 对整治边坡破坏提出参考依据

轮式移动仿人机器人的动力学建模与分析

利用高效迭代牛顿-欧拉方法对一个21自由度的轮式移动仿人机器人进行了整体动力学建模,该模型虽然维数较高,但消除了分块建模中需要对模块之间相互作用力进行建模的难点问题,并且由于机器人双臂的对称结构,当合理规划双臂运动时,动力学模型将得到部分简化。本文还对某关节运动时在各个关节所产生的力或力矩进行了仿真分析。解析及仿真结果表明,合理规划上臂各关节的协调运动,将极大地削弱车体及腰部各关节所受的力或力矩扰动,为基于动力学的机器人运动控制以及稳定性分析提供理论依据。

互联网上机器人的遥控理论与方法综述

给出了系统的研究模型,指出系统控制和设计必须考虑的3个关键问题:稳定性、透明性和时延处理.阐述了4个主要的稳定性分析方法:Lyapunov稳定性、输入输出稳定性、无源稳定性和基于事件的稳定性,总结了这些方法的优势和局限性.接着,给出了几种主要的控制策略,指出了现有控制方法的优缺点.最后,提出了进一步的主要研究方向.

新型轮—腿—履带复合移动机构及稳定性分析

为提高反恐防暴机器人对非结构环境的适应能力,设计出了一种具有良好的机动性能和转向性能的新型轮—腿—履带复合移动机构.通过机器人机构分析与本体的稳定性分析,论证了其结构设计的可行性及好的稳定性.