Some aspects of European climate policy

Being heavily energy dependent, it is not much of a surprise that Europe pays special attention to reducing the use of fossil fuels. Each one of the ten new member states is characterized by relatively low per capita energy consumption and relatively low energy efficiency, and the share of renewables in their energy mix tends to be low, too. The paper examines the problem, when the policy measures create a decrease in environmental capital instead of an increase. In this case it hardly seems justified to talk about environmental protection. The authors describe a case of a rapeseed oil mill which would not be of too much interest on its own but given that almost all similar plants went bankrupt, there are some important lessons to learn from its survival. The enterprise the authors examined aimed at establishing a micro-regional network. They completed a brown-field development to establish a small plant on the premises of a former large agricultural cooperative. By partnering with the former employees and suppliers of the sometime cooperative, they enjoyed some benefits which all the other green-field businesses focusing on fuel production could not. The project improved food security, energy security and population retention as well.

Clean hydrogen production and carbon dioxide capture methods

Fossil fuels constitute a significant fraction of the world's energy demand. The burning of fossil fuels emits huge amounts of carbon dioxide into the atmosphere. Therefore, the limited availability of fossil fuel resources and the environmental impact of their use require a change to alternative energy sources or carriers (such as hydrogen) in the foreseeable future. The development of methods to mitigate carbon dioxide emission into the atmosphere is equally important. Hence, extensive research has been carried out on the development of cost-effective technologies for carbon dioxide capture and techniques to establish hydrogen economy. Hydrogen is a clean energy fuel with a very high specific energy content of about 120MJ/kg and an energy density of 10Wh/kg. However, its potential is limited by the lack of environment-friendly production methods and a suitable storage medium. Conventional hydrogen production methods such as Steam-methane-reformation and Coal-gasification were modified by the inclusion of NaOH. The modified methods are thermodynamically more favorable and can be regarded as near-zero emission production routes. Further, suitable catalysts were employed to accelerate the proposed NaOH-assisted reactions and a relation between reaction yield and catalyst size has been established. A 1:1:1 molar mixture of LiAlH 4, NaNH2 and MgH2 were investigated as a potential hydrogen storage medium. The hydrogen desorption mechanism was explored using in-situ XRD and Raman Spectroscopy. Mesoporous metal oxides were assessed for CO2 capture at both power and non-power sectors. A 96.96% of mesoporous MgO (325 mesh size, surface area = 95.08 ± 1.5 m2/g) was converted to MgCO 3 at 350°C and 10 bars CO2. But the absorption capacity of 1h ball milled zinc oxide was low, 0.198 gCO2 /gZnO at 75°C and 10 bars CO2. Interestingly, 57% mass conversion of Fe and Fe 3O4 mixture to FeCO3 was observed at 200°C and 10 bars CO2. MgO, ZnO and Fe3O4 could be completely regenerated at 550°C, 250°C and 350°C respectively. Furthermore, the possible retrofit of MgO and a mixture of Fe and Fe3O 4 to a 300 MWe coal-fired power plant and iron making industry were also evaluated.

Alterações morfofisiológicas e moleculares em resposta a estresses abióticos em mamona (Ricinus communis L.)

The use of fossil fuels has been considered one of reason for the increase of pollution in the atmosphere and it may be related to the climate changes. Then, the research of the new sources of fuels will be important. Considering this, the use of biodiesel has been considered not as bad as petrol. The castor bean (Ricinus communis L.) is an important oilseed, which belongs to Euphorbiaceae family, and the oil found in the seed has important characteristics for biodiesel. This plant is considered as “rustic” as it does not need so much water for its development and oil production. Due to this, this plant has been considered to be ideal in semi-arid regions, such as the Northeast of Brazil. The aim of his study is to better understand the responses to abiotic stresses (drought and salinity) from castor bean plants using morphological, physiological and molecular tools. In order to do this, the castor bean plants were subjected to salt stress (50, 100, 150 and 200 mM NaCl) in a controlled environment and drought stress (5, 10, 15 days and 10 days cyclic). After these treatments, these plants were subjected to different analyzes: a) the expansion and retention of water from leaves; b) anatomy using leaves and roots. Based on these results, we found that castor suffered decrease in leaf area with increase drought stress, however restricted water loss, probably by accumulation of compatible solutes in the leaves. The anatomy data showed modifications in the vascular system. These modifications observed suggested that castor bean plant may be resistant to stress as it was verified in 5 days of drought as well as in 100 mM NaCl. In both conditions, these plants were fine. Probably these plants keep some solutes in the cell and then maintain the cell tugor. The data obtained in this study gave a better idea how castor bean plant responds to abiotic stress conditions - drought and salt stress

Identificação das políticas de incentivo ao desenvolvimento da energia eólica no Rio Grande do Norte (RN)

Energy is a vital resource for social and economic development. In the present scenario, the search for alternative energy sources has become fundamental, especially after the oil crises between 1973 and 1979, the Chernobyl nuclear accident in 1986 and the Kyoto Protocol in 1997. The demand for the development of new alternative energy sources aims to complement existing forms allows to meet the demand for energy consumption with greater security. Brazil, with the guideline of not dirtying the energy matrix by the fossil fuels exploitation and the recent energy crisis caused by the lack of rains, directs energy policies for the development of other renewable energy sources, complementing the hydric. This country is one of the countries that stand out for power generation capacity from the winds in several areas, especially Rio Grande do Norte (RN), which is one of the states with highest installed power and great potential to be explored. In this context arises the purpose of this work to identify the incentive to develop policies of wind energy in Rio Grande do Norte. The study was conducted by a qualitative methodology of data analysis called content analysis, oriented for towards message characteristics, its informational value, the words, arguments and ideas expressed in it, constituting a thematic analysis. To collect the data interviews were conducted with managers of major organizations related to wind energy in Brazil and in the state of Rio Grande do Norte. The identification of incentive policies was achieved in three stages: the first seeking incentives policies in national terms, which are applied to all states, the second with the questionnaire application and the third to research and data collection for the development of the installed power of the RN as compared to other states. At the end, the results demonstrated hat in Rio Grande do Norte state there is no incentive policy for the development of wind power set and consolidated, specific actions in order to optimize the bureaucratic issues related to wind farms, especially on environmental issues. The absence of this policy hinders the development of wind energy RN, considering result in reduced competitiveness and performance in recent energy auctions. Among the perceived obstacles include the lack of hand labor sufficient to achieve the reporting and analysis of environmental licenses, the lack of updating the wind Atlas of the state, a shortfall of tax incentives. Added to these difficulties excel barriers in infrastructure and logistics, with the lack of a suitable port for large loads and the need for reform, maintenance and duplication of roads and highways that are still loss-making. It is suggested as future work the relationship of the technology park of energy and the development of wind power in the state, the influence of the technology park to attract businesses and industries in the wind sector to settle in RN and a comparison of incentive policies to development of wind energy in the Brazilian states observing wind development in the same states under study.

Efeitos de fungicidas alternativos em folhas de Carthamus tinctorius L. (Asteraceae), potencial espécie para cultivo em agricultura familiar

The currently main development model on global society is driven by an economic rationality that endangers the environment and social justice. More and more, attention to this way of production and consumption is increasing, boosting research for sustainable development, with an environmental rationality that can harmonize nature preservation and welfare of all socioeconomic classes. One of the efforts on this sense is changing the sources supplying the energy demand, replacing fossil fuels for renewable and cleaner sources, such as biofuels. Carthamus tinctorius (safflower) is an oilseed crop with potential for biodiesel production, with good oil yield and chemical profile, allied to good adaptation to climates such like the northeastern semiarid lands of Brazil. With public policies fomentation, the use of this species may be an interesting alternative for family farming. In farming in general, the use of pesticides to prevent and combat diseases and plagues is common, which is not a sustainable practice. Thus, there are researched alternative, less dangerous substances. In this study, it was aimed to assess if neem (Azadirachta indica) leaf extract (20% m/v) and Bordeaux mixture (copper sulfate) have effects on safflower. It was also aimed to verify acceptance of farmers on safflower crop in Apodi, a municipality in Rio Grande do Norte state, Brazil, in view of it being localized in the aimed region for this crop cultivation. Besides that, understanding that the farmers’ knowledge and inclination to adopt the crop is fundamental for the introduction of this species and socioeconomic growth due to its exploration. In addition, a booklet with basic information on safflower was produced. In the field experiment, the fungicides were pulverized on plants cultivated in field experimental plots, with collection of leaf samples for analysis on anatomy, cuticle, and epicuticular wax morphology, the protective layer that interfaces with the surrounding ambient. In Apodi, forty-five farmers from Potiguar Cooperative of Apiculture and Sustainable Rural Development (COOPAPI) underwent semi-structured interviews, which also addressed their assessment on currently cultivated crops and perception of pesticide uses and sustainable alternatives. After comparing using analysis of variance, it was found that there was no difference between treatments in the experiment, as well as no anatomical or morphological modifications. Safflower acceptation among farmers was wide, with 84% of interviewees believing in a perspective of good incomes. The current scenario, comprised of low crop diversity, fragile in face of droughts and plagues, can partially explain this opinion. The booklet was effective in catching people attention for the species potential. There was wide acknowledgement on the importance of alternative pesticides, justified by health security. Based on the assessed parameter in the results of this research, the treatments here utilized may be recommended as fungicides for safflower. Given the crop susceptibility to fungi in heavy rainy period, it is advised that its potential introduction on the region shall be focused on semiarid areas.

Consórcio de cártamo e feijão caupi: alternativa para a produção de biodiesel na agricultura familiar

The new development strategies should operate mainly in the areas of energy efficiency and sustainable agriculture. Thus, the substitution of fossil fuels with biofuels, such as biodiesel, is increasingly on the agenda. The cultivation of oilseed plants for biodiesel production must take place in integrated systems that enable best environmental benefits and are more economically significant. The objectives of this study were to assess the morphological, anatomic, and physiological characteristics of safflower (Carthamus tinctorius L., promising oilseed for biodiesel production) grown in monoculture and intercropping with cowpea bean (Vigna unguiculata L. Walp.); and identify socioeconomic family farmers and verify their acceptance about safflower as an energy crop. The methodology used for the analysis of safflower growth in monoculture and intercropped with beans, were morphoanatomical and histochemical analyzes, made with samples of plants grown in the field in two cropping systems throughout the range of the life cycle of these plants. There were no changes in growth and anatomy of plants, even in the consortium, which is satisfactory to indicate the intercropping system for those crops and can be a good alternative for the family farmer, who may have safflower as a source of income without giving up planting their livelihood. To check the acceptance of safflower by farmers, interviews were made to family farmers by Canudos agrovila in Ceará-Mirim/RN. It was noticed that many of them accept the introduction of safflower as oil crop, although unaware of the species, and that, being more resistant to drought, safflower help in the stability of families who depend on the weather conditions for success their current crops. In general, it is concluded that safflower has features that allows it to be grown in consortium for biodiesel production combined with the production of food, such as cowpea, and can be used enabling better development for family farmers.

Energia eólica em alto mar: distribuição dos recursos e complementaridade hídrica

The stabilization of energy supply in Brazil has been a challenge for the operation of the National Interconnected System in face of hydrological and climatic variations. Thermoelectric plants have been used as an emergency source for periods of water scarcity. The utilization of fossil fuels, however, has elevated the cost of electricity. On the other hand, offshore wind energy has gained importance in the international context and is competitive enough to become a possibility for future generation in Brazil. In this scenario, the main goal of this thesis was to investigate the magnitude and distribution of offshore wind resources, and also verify the possibilities of complementing hydropower. A data series of precipitation from the Climatic Research Unit (CRU) Blended Sea Winds from the National Climatic Data Center (NCDC/NOAA) were used. According to statistical criteria, three types of complementarity were found in the Brazilian territory: hydro × hydro, wind × wind and hydro × wind. It was noted a significant complementarity between wind and hydro resources (r = -0.65), mainly for the hydrographical basins of the southeast and central regions with Northeastern Brazil winds. To refine the extrapolation of winds over the ocean, a method based on the Monin-Obukhov theory was used to model the stability of the atmospheric boundary layer. Objectively Analyzed Air-Sea Flux (OAFLUX) datasets for heat flux, temperature and humidity, and also sea level pressure data from NCEP/NCAR were used. The ETOPO1 from the National Geophysical Data Center (NGDC/NOAA) provided bathymetric data. It was found that shallow waters, between 0-20 meters, have a resource estimated at 559 GW. The contribution of wind resources to hydroelectric reservoir operation was investigated with a simplified hybrid wind-hydraulic model, and reservoir level, inflow, outflow and turbine production data. It was found that the hybrid system avoids drought periods, continuously saving water from reservoirs through wind production. Therefore, from the results obtained, it is possible to state that the good winds from the Brazilian coast can, besides diversifying the electric matrix, stabilize the hydrological fluctuations avoiding rationing and blackouts, reducing the use of thermal power plants, increasing the production cost and emission of greenhouse gases. Public policies targeted to offshore wind energy will be necessary for its full development.

Contribuições para estratégia de controle aplicada à geração fotovoltaica interconectada à rede elétrica

Generation systems, using renewable sources, are becoming increasingly popular due to the need for increased use of electricity. Currently, renewables sources have a role to cooperate with conventional generation, due to the system limitation in delivering the required power, the need for reduction of unwanted effects from sources that use fossil fuels (pollution) and the difficulty of building new transmission and/or distribution lines. This cooperation takes place through distributed generation. Therefore, this work proposes a control strategy for the interconnection of a PV (Photovoltaic) system generation distributed with a three-phase power grid through a connection filter the type LCL. The compensation of power quality at point of common coupling (PCC) is performed ensuring that the mains supply or consume only active power and that his currents have low distorcion. Unlike traditional techniques which require schemes for harmonic detection, the technique performs the harmonic compensation without the use of this schemes, controlling the output currents of the system in an indirect way. So that there is effective control of the DC (Direct Current) bus voltage is used the robust controller mode dual DSMPI (Dual-Sliding Mode-Proportional Integral), that behaves as a sliding mode controller SM-PI (Sliding Mode-Proportional Integral) during the transition and like a conventional PI (Proportional Integral) in the steady-state. For control of current is used to repetitive control strategy, which are used double sequence controllers (DSC) tuned to the fundamental component, the fifth and seventh harmonic. The output phase current are aligned with the phase angle of the utility voltage vector obtained from the use of a SRF-PLL (Synchronous Reference Frame Phase-Locked-Loop). In order to obtain the maximum power from the PV array is used a MPPT (Maximum Power Point Tracking) algorithm without the need for adding sensors. Experimental results are presented to demonstrate the effectiveness of the proposed control system.

Seawater carbonate chemistry and calcification in the tropical urchin Echinometra viridis in a laboratory experiment

Atmospheric carbon dioxide (pCO2) has risen from approximately 280 to 400 ppm since the Industrial Revolution, due mainly to the combustion of fossil fuels, deforestation, and cement production. It is predicted to reach as high as 900 ppm by the end of this century. Ocean acidification resulting from the release of anthropogenic CO2 has been shown to impair the ability of some marine calcifiers to build their shells and skeletons. Here, we present the results of ocean acidification experiments designed to assess the effects of an increase in atmospheric pCO2 from ca. 448 to 827 ppm on calcification rates of the tropical urchin Echinometra viridis. Experiments were conducted under the urchin's winter (20 °C) and summer (30 °C) water temperatures in order to identify seasonal differences in the urchin's response to ocean acidification. The experiments reveal that calcification rates decreased for urchins reared under elevated pCO2, with the decline being more pronounced under wintertime temperatures than under summertime temperatures. These results indicate that the urchin E. viridis will be negatively impacted by CO2-induced ocean acidification that is predicted to occur by the end of this century. These results also suggest that impact of CO2-induced ocean acidification on urchin calcification will be more severe in the winter and in cooler waters.

Heavy metals and carbon isotope concentrations in recent Baltic Sea sediments

Recent sediment cores of the western Baltic Sea were analyzed for heavy metal and carbon isotope contents. The sedimentation rate was determined from radiocarbon dates to be 1.4 mm/yr. The 'recent age' of the sediment was about 850 yr. Within the upper 20 cm of sediment, certain heavy metals became increasingly enriched towards the surface; Cd, Pb, Zn and Cu increased 7-, 4-, 3- and 2-fold, respectively, whereas Fe, Mn, Ni and Co remained unchanged. Simultaneously, the radiocarbon content decreased by about 14 per cent. The enrichment in heavy metals as well as the decrease in the 14C-concentration during the last 130 ± 30yr parallels industrial growth as reflected in European fossil fuel consumption within that same period of time. The near-surface sediments are affected by residues released from fossil fuels at the rate of about 30 g/m**2 yr for the past two decades. The residues have a pronounced effect on the heavy metal and carbon isotope composition of the most Recent sediments allowing estimates to be made for sedimentation, erosion and heavy metal pollution.

Modelagem e análise dinâmica de um sistema de conversão de energia eólica dotado de gerador síncrono de imã permanente utilizando a plataforma ATP

Human development requires a broad balance between ecological, social and economic factors in order to ensure its own sustainability. In this sense, the search for new sources of energy generation, with low deployment and operation costs, which cause the least possible impact to the environment, has been the focus of attention of all society segments. To do so, the reduction in exploration of fossil fuels and the encouragement of using renewable energy resources for distributed generation have proved interesting alternatives to the expansion of the energy matrix of various countries in the world. In this sense, the wind energy has acquired an increasingly significant role, presenting increasing rates of power grid penetration and highlighting technological innovations such as the use of permanent magnet synchronous generators (PMSG). In Brazil, this fact has also been noted and, as a result, the impact of the inclusion of this source in the distribution and sub-transmission power grid has been a major concern of utilities and agents connected to Brazilian electrical sector. Thus, it is relevant the development of appropriate computational tools that allow detailed predictive studies about the dynamic behavior of wind farms, either operating with isolated load, either connected to the main grid, taking also into account the implementation of control strategies for active/reactive power generation and the keeping of adequate levels of voltage and frequency. This work fits in this context since it comprises mathematical and computational developments of a complete wind energy conversion system (WECS) endowed with PMSG using time domain techniques of Alternative Transients Program (ATP), which prides itself a recognized reputation by scientific and academic communities as well as by electricity professionals in Brazil and elsewhere. The modeling procedures performed allowed the elaboration of blocks representing each of the elements of a real WECS, comprising the primary source (the wind), the wind turbine, the PMSG, the frequency converter, the step up transformer, the load composition and the power grid equivalent. Special attention is also given to the implementation of wind turbine control techniques, mainly the pitch control responsible for keeping the generator under the maximum power operation point, and the vector theory that aims at adjusting the active/reactive power flow between the wind turbine and the power grid. Several simulations are performed to investigate the dynamic behavior of the wind farm when subjected to different operating conditions and/or on the occurrence of wind intensity variations. The results have shown the effectiveness of both mathematical and computational modeling developed for the wind turbine and the associated controls.

A busca por uma política nacional dos biocombustíveis como tutela do direito fundamental ao meio ambiente : acautelamento e avaliação de riscos

The work is to demonstrate the scope of modern-day major regulatory provisions and the policies implemented to adoption of biofuels in the national energy matrix. The adoption of biofuels as an alternative to fossil fuels, is based on the realization of the fundamental right to an ecologically balanced environment mitigating hazards and environmental hazards arising from a postmodern society. However, the change in the Brazilian energy matrix observe the precepts of certain environmental principles to essentially environmental preservation The proposed Environmental rule of law is founded on the realization of the right (duty) key to an ecologically balanced environment for sustainable development. Thus, it is up to the State, in addition to considering the dangers and risks fruits of government decisions, present the possible instruments to mitigate the irreversible environmental damage to the environment. The management of environmental risks present in the ideals of an Environmental rule of law, plays an important role in the preservation and economic development, using, therefore, of acautelatórios legal instruments, such as environmental licensing and the ecological-economic zoning, measures adopted in the light of the principles of precaution and preservation. The adoption of research in the environmental field, improvement and development of environmental technology, building a system to observe ecological changes, imposition of environmental policy objectives to be achieved in the medium and long term and systematization of organizations plan a protection policy environmental, are essential measures to control possible environmental risks and damage guided by the aforementioned environmental principles. Thus, it will be used the inductive method of approach, starting from the analysis of the new perspective of Environmental rule of law and the implementation of biofuels in the context of a post-modern society, marked by uncertainty and the risk of damage, from the study of the principles of caution, maintaining and cautionary measures in mitigating the hazards and potential risks.

Nanostructured Metal Oxide Coatings for Electrochemical Energy Conversion and Storage Electrodes

The realization of an energy future based on safe, clean, sustainable, and economically viable technologies is one of the grand challenges facing modern society. Electrochemical energy technologies underpin the potential success of this effort to divert energy sources away from fossil fuels, whether one considers alternative energy conversion strategies through photoelectrochemical (PEC) production of chemical fuels or fuel cells run with sustainable hydrogen, or energy storage strategies, such as in batteries and supercapacitors. This dissertation builds on recent advances in nanomaterials design, synthesis, and characterization to develop novel electrodes that can electrochemically convert and store energy.

Chapter 2 of this dissertation focuses on refining the properties of TiO2-based PEC water-splitting photoanodes used for the direct electrochemical conversion of solar energy into hydrogen fuel. The approach utilized atomic layer deposition (ALD); a growth process uniquely suited for the conformal and uniform deposition of thin films with angstrom-level thickness precision. ALD’s thickness control enabled a better understanding of how the effects of nitrogen doping via NH3 annealing treatments, used to reduce TiO2’s bandgap, can have a strong dependence on TiO2’s thickness and crystalline quality. In addition, it was found that some of the negative effects on the PEC performance typically associated with N-doped TiO2 could be mitigated if the NH3-annealing was directly preceded by an air-annealing step, especially for ultrathin (i.e., < 10 nm) TiO2 films. ALD was also used to conformally coat an ultraporous conductive fluorine-doped tin oxide nanoparticle (nanoFTO) scaffold with an ultrathin layer of TiO2. The integration of these ultrathin films and the oxide nanoparticles resulted in a heteronanostructure design with excellent PEC water oxidation photocurrents (0.7 mA/cm2 at 0 V vs. Ag/AgCl) and charge transfer efficiency.

In Chapter 3, two innovative nanoarchitectures were engineered in order to enhance the pseudocapacitive energy storage of next generation supercapacitor electrodes. The morphology and quantity of MnO2 electrodeposits was controlled by adjusting the density of graphene foliates on a novel graphenated carbon nanotube (g-CNT) scaffold. This control enabled the nanocomposite supercapacitor electrode to reach a capacitance of 640 F/g, under MnO2 specific mass loading conditions (2.3 mg/cm2) that are higher than previously reported. In the second engineered nanoarchitecture, the electrochemical energy storage properties of a transparent electrode based on a network of solution-processed Cu/Ni cores/shell nanowires (NWs) were activated by electrochemically converting the Ni metal shell into Ni(OH)2. Furthermore, an adjustment of the molar percentage of Ni plated onto the Cu NWs was found to result in a tradeoff between capacitance, transmittance, and stability of the resulting nickel hydroxide-based electrode. The nominal area capacitance and power performance results obtained for this Cu/Ni(OH)2 transparent electrode demonstrates that it has significant potential as a hybrid supercapacitor electrode for integration into cutting edge flexible and transparent electronic devices.

Dynamic Life Cycle Assessment Modeling Approaches for Transboundary Energy Feedstocks

The rise of the twenty-first century has seen the further increase in the industrialization of Earth’s resources, as society aims to meet the needs of a growing population while still protecting our environmental and natural resources. The advent of the industrial bioeconomy – which encompasses the production of renewable biological resources and their conversion into food, feed, and bio-based products – is seen as an important step in transition towards sustainable development and away from fossil fuels. One sector of the industrial bioeconomy which is rapidly being expanded is the use of biobased feedstocks in electricity production as an alternative to coal, especially in the European Union.

As bioeconomy policies and objectives increasingly appear on political agendas, there is a growing need to quantify the impacts of transitioning from fossil fuel-based feedstocks to renewable biological feedstocks. Specifically, there is a growing need to conduct a systems analysis and potential risks of increasing the industrial bioeconomy, given that the flows within it are inextricably linked. Furthermore, greater analysis is needed into the consequences of shifting from fossil fuels to renewable feedstocks, in part through the use of life cycle assessment modeling to analyze impacts along the entire value chain.

To assess the emerging nature of the industrial bioeconomy, three objectives are addressed: (1) quantify the global industrial bioeconomy, linking the use of primary resources with the ultimate end product; (2) quantify the impacts of the expaning wood pellet energy export market of the Southeastern United States; (3) conduct a comparative life cycle assessment, incorporating the use of dynamic life cycle assessment, of replacing coal-fired electricity generation in the United Kingdom with wood pellets that are produced in the Southeastern United States.

To quantify the emergent industrial bioeconomy, an empirical analysis was undertaken. Existing databases from multiple domestic and international agencies was aggregated and analyzed in Microsoft Excel to produce a harmonized dataset of the bioeconomy. First-person interviews, existing academic literature, and industry reports were then utilized to delineate the various intermediate and end use flows within the bioeconomy. The results indicate that within a decade, the industrial use of agriculture has risen ten percent, given increases in the production of bioenergy and bioproducts. The underlying resources supporting the emergent bioeconomy (i.e., land, water, and fertilizer use) were also quantified and included in the database.

Following the quantification of the existing bioeconomy, an in-depth analysis of the bioenergy sector was conducted. Specifically, the focus was on quantifying the impacts of the emergent wood pellet export sector that has rapidly developed in recent years in the Southeastern United States. A cradle-to-gate life cycle assessment was conducted in order to quantify supply chain impacts from two wood pellet production scenarios: roundwood and sawmill residues. For reach of the nine impact categories assessed, wood pellet production from sawmill residues resulted in higher values, ranging from 10-31% higher.

The analysis of the wood pellet sector was then expanded to include the full life cycle (i.e., cradle-to-grave). In doing to, the combustion of biogenic carbon and the subsequent timing of emissions were assessed by incorporating dynamic life cycle assessment modeling. Assuming immediate carbon neutrality of the biomass, the results indicated an 86% reduction in global warming potential when utilizing wood pellets as compared to coal for electricity production in the United Kingdom. When incorporating the timing of emissions, wood pellets equated to a 75% or 96% reduction in carbon dioxide emissions, depending upon whether the forestry feedstock was considered to be harvested or planted in year one, respectively.

Finally, a policy analysis of renewable energy in the United States was conducted. Existing coal-fired power plants in the Southeastern United States were assessed in terms of incorporating the co-firing of wood pellets. Co-firing wood pellets with coal in existing Southeastern United States power stations would result in a nine percent reduction in global warming potential.

Ultra High Pressure Hydrogen Studies

Hydrogen has been called the fuel of the future, and as it’s non- renewable counterparts become scarce the economic viability of hydrogen gains traction. The potential of hydrogen is marked by its high mass specific energy density and wide applicability as a fuel in fuel cell vehicles and homes. However hydrogen’s volume must be reduced via pressurization or liquefaction in order to make it more transportable and volume efficient. Currently the vast majority of industrially produced hydrogen comes from steam reforming of natural gas. This practice yields low-pressure gas which must then be compressed at considerable cost and uses fossil fuels as a feedstock leaving behind harmful CO and CO2 gases as a by-product. The second method used by industry to produce hydrogen gas is low pressure electrolysis. In comparison the electrolysis of water at low pressure can produce pure hydrogen and oxygen gas with no harmful by-products using only water as a feedstock, but it will still need to be compressed before use. Multiple theoretical works agree that high pressure electrolysis could reduce the energy losses due to product gas compression. However these works openly admit that their projected gains are purely theoretical and ignore the practical limitations and resistances of a real life high pressure system. The goal of this work is to experimentally confirm the proposed thermodynamic gains of ultra-high pressure electrolysis in alkaline solution and characterize the behavior of a real life high pressure system.