Trawling pull exerted by a trawler: a method of estimation from propeller dimensions and its comparison with sea measurements

The proper matching of the pull exerted by a trawler and the size of trawl is important for maximizing the catching efficiency. The available pull is more dependent on the propeller and its working conditions than the installed engine power. The normal practice is to directly connect net size to the installed power in the boat by formulae without reference to the prope1ler dimensions or the available trawling pull and this is not adequate to find out the optimum combination. By the method outlined in this paper, the accurate calculation of trawling pull is possible by taking into account only the propeller diameter, pitch and r. p. m. The predictions by the method are compared for trawlers with powers between 30 and 60 hp and agreement is found to be within + 5%. The power absorbed by the propeller in trawling condition can also be calculated by this method for checking whether the engine is being overloaded.

TIME RESOLVED REFLECTIVITY MEASUREMENTS APPLIED TO RAPID ISOTHERMAL ANNEALING OF ION IMPLANTED SILICON.

The annealing of ion implantation damage in silicon by rapid isothermal heating has been monitored by the time resolved reflectivity (TRR) method. This technique was applied simultaneously at a wavelength of 632. 8nm and also at 1152nm, where the optical absorption coefficient of silicon is less. The two wavelength method simplifies the interpretation of TRR results, extends the measurement depth and allows good resolution of the position of the interface between amorphous and crystalline silicon. The regrowth of amorphous layers in silicon, created by self implantation and implanted with electrically active impurities, was observed. Regrowth in rapid isothermal annealing occurs during the heating up stage of typical thermal cycles. Impurities such as B, P, and As increase the regrowth rate in a manner consistent with a vacancy model for regrowth. The maximum regrowth rate in boron implanted silicon is limited by the solid solubility.

SOME MEASUREMENTS OF THE PERMEABILITY OF KAOLIN.

This paper reports an experimental investigation of the vertical and horizontal permeabilities of speswhite kaolin clay. The permeabilities were measured using falling head permeability tests. A modification to a conventional oedometer was devised so that either vertical or horizontal permeabilities could be determined. It was found that the vertical and horizontal permeabilities of the clay slurry were similar, but that as the clay was consolidated one dimensionally the anisotropy of the clay fabric resulted in a greater horizontal permeability than the vertical permeability at any void ratio. Both permeabilities were uniquely related to the void ratio.

Some measurements of the permeability of kaolin

The writers wish to present some additional data obtained independently and with different techniques that confirm the results published in the paper. For these tests, the speswhite kaolin clay was prepared as a slurry with a water content of 133 percent and was then consolidated one-dimensionally under an axial stress of 100 kPa in a 203 mm dia. tube. The results presented here show that the anisotropy of permeability is completely preserved (even after the sample is compressed isotropical) as long as the initial part of the stress path corresponds to one-dimensional compression. The data supports the speculation by the authors regarding permeability anisotropy for stress paths other than one-dimensional compression.

Unsteady transition in an axial-flow turbine. Part 2. Cascade measurements and modeling

Part 1 of this paper reanalyzed previously published measurements from the rotor of a low-speed, single-stage, axial-flow turbine, which highlighted the unsteady nature of the suction surface transition process. Part 2 investigates the significance of the wake jet and the unsteady frequency parameter. Supporting experiments carried out in a linear cascade with varying inlet turbulence are described, together with a simple unsteady transition model explaining the features of seen in the turbine.

Unsteady transition in an axial-flow turbine. Part 1. Measurements on the turbine rotor

Previously published measurements in a low-speed, single-stage, axial-flow turbine have been reanalyzed in the light of more recent understanding. The measurements include time-resolved hot-wire traverses and surface hot film gage measurements at the midspan of the rotor suction surface with three different rotor-stator spacings. This paper investigates the suction surface boundary layer transition process, using surface-distance time plots and boundary layer cross sections to demonstrate the unsteady and two-dimensional nature of the process.