Efeito da Gália como aditivo de sinterização em eletrólitos cerâmicos à base de céria sintetizados pelo método de complexação de cátions

Fuel cells are considered one of the most promising ways of converting electrical energy due to its high yield and by using hydrogen (as fuel) which is considered one of the most important source of clean energy for the future. Rare earths doped ceria has been widely investigated as an alternative material for the electrolyte of solid oxide fuel cells (SOFCs) due to its high ionic conductivity at low operating temperatures compared with the traditional electrolytes based on stabilized zirconia. This work investigates the effect of gallium oxide (Gallia) as a sintering aid in Eu doped ceria ceramic electrolytes since this effect has already been investigated for Gd, Sm and Y doped ceria electrolytes. The desired goal with the use of a sintering aid is to reduce the sintering temperature aiming to produce dense ceramics. In this study we investigated the effects on densification, microstructure and ionic conduction caused by different molar fraction of the dopants europium (10, 15 and 20%) and gallium oxide (0.3, 0.6 and 0.9%) in samples sintered at 1300, 1350 and 1450 0 C. Samaria (10 and 20%) doped ceria samples sintered between 1350 and 1450 °C were used as reference. Samples were synthesized using the cation complexation method. The ceramics powders were characterized by XRF, XRD and SEM, while the sintered samples were investigated by its relative density, SEM and impedance spectroscopy. It was showed that gallia contents up to 0.6% act as excellent sintering aids in Eu doped ceria. Above this aid content, gallia addition does not promote significant increase in density of the ceramics. In Ga free samples the larger densification were accomplished with Eu 15% molar, effect expressed in the microstructure with higher grain growth although reduced and surrounded by many open pores. Relative densities greater than 95 % were obtained by sintering between 1300 and 1350 °C against the usual range 1500 - 1600 0 C. Samples containing 10% of Sm and 0.9% of Ga reached 96% of theoretical density by sintering at 1350 0 C for 3h, a gain compared to 97% achieved with 20% of Sm and 1% of Ga co-doped cerias sintered at 1450 0 C for 24 h as described in the literature. It is found that the addition of gallia in the Eu doped ceria has a positive effect on the grain conductivity and a negative one in the grain boundary conductivity resulting in a small decrease in the total conductivity which will not compromise its application as sintering aids in ceria based electrolytes. Typical total conductivity values at 600 and 700 °C, around 10 and 30 mS.cm -1 respectively were reached in this study. Samples with 15% of Eu and 0.9 % of Ga sintered at 1300 and 1350 °C showed relative densities greater than 96% and total conductivity (measured at 700 °C) between 20 and 33 mS.cm -1 . The simultaneous sintering of the electrolyte with the anode is one of the goals of research in materials for SOFCs. The results obtained in this study suggest that dense Eu and Ga co-doped ceria electrolytes with good ionic conductivity can be sintered simultaneously with the anode at temperatures below 1350 °C, the usual temperature for firing porous anode materials

Compósitos de matriz metálica à base níquel com adição de TaC e NbC produzidos via metalurgia do pó

Carbide reinforced metallic alloys potentially improve some important mechanical properties required for the overall use of important engineering materials such as steel and nickel. Nevertheless, improved performance is achieved not only by composition enhancement but also by adequate processing techniques, such as novel sintering methods in the case of powder metallurgy. The method minimizes energy losses in addition to providing uniform heating during sintering. Thus, the general objective of this study was to evaluate the density, hardness, flexural strength, dilatometric behavior and to analyze the microstructure of metal matrix composites based nickel with addition of carbides of tantalum and / or niobium when sintered in a conventional furnace and Plasma assisted debinding and sintering (PADS). Initially, were defineds best parameters of granulation, screening and mixing procedure. After, mixtures of carbonyl Ni and 5%, 10% and 15 wt.% NbC and TaC were prepared in a Y-type mixer under wet conditions during 60 minutes. The mixtures were then dried and granulated using 1.5 wt. % paraffin diluted in hexane. Granulates were cold pressed under 600 MPa. Paraffin was then removed from the pressed pellets during a pre-sintering process carried out in a tubular furnace at 500 °C during 30 min. The heating rate was 3 ºC/min. The pellets were then sintered using either a plasma assisted reactor or a conventional resistive tubular furnace. For both methods, the heating rate was set to 8 ºC/min up to 1150 °C. The holding time was 60 minutes. The microstructure of the sintered samples was evaluated by SEM. Brinell hardness tests were also carried out. The results revealed that higher density and higher hardness values were observed in the plasma-assisted sintered samples. Hardness increased with the concentration of carbides in the Ni-matrix. The flexural strength also increased by adding the carbides. The decline was larger for the sample with addition of 5% 5% TaC and NbC. In general, compositions containing added carbide 10% showed less porous and more uniform distribution of carbides in the nickel matrix microstructural appearance. Thus, both added carbide and plasma sintering improved density, hardness, flexural strength and microstructural appearance of the composites

Plásticos reforçados a base de tecidos híbridos: efeitos da anisotropia e geometria normativa na caracterização mecânica e da fratura

As most current studies, reinforced plastics have been, in recent years, a viable alternative in building structural elements of medium and large, since the lightness accompanied by high performance possible. The design of hybrid polymer composites (combination of different types of reinforcements) may enable structural applications thereof, facing the most severe service conditions. Within this class of composite materials, reinforced the underlying tissues hybrid high performance are taking space when your application requires high load bearing and high rigidity. The objective of this research work is to study the challenges in designing these fabrics bring these materials as to its mechanical characterization and fracture mechanisms involved. Some parameters associated with the process and / or form of hybridization stand out as influential factors in the final performance of the material such as the presence of anisotropy, so the fabric weave, the process of making the same, normative geometry of the specimens, among others. This sense, four laminates were developed based hybrid reinforcement fabrics involving AS4 carbon fiber, kevlar and glass 49-E as the matrix epoxy vinyl ester resin (DERAKANE 411-350). All laminates were formed each with four layers of reinforcements. Depending on the hybrid fabric, all the influencing factors mentioned above have been studied for laminates. All laminates were manufactured industrially used being the lamination process manual (hand-lay-up). All mechanical characterization and study of the mechanism of fracture (fracture mechanics) was developed for laminates subjected to uniaxial tensile test, bending in three and uniaxial compression. The analysis of fracture mechanisms were held involving the macroscopic, optical microscopy and scanning electron microscopy

Sinterização de matrizes cerâmicas à base de alumina reforçadas por carbetos a partir de precursores poliméricos

Ceramic composites produced with polymerics precursors have been studied for many years, due to the facility of obtaining a complex shape, at low temperature and reduces cost. The main objective of this work is to study the process of sintering of composites of ceramic base consisting of Al2O3 and silicates, reinforced for NbC, through the technique of processing AFCOP, as well as the influence of the addition of LZSA, ICZ and Al as materials infiltration in the physical and mechanical properties of the ceramic composite. Were produced ceramic matrix composites based SiCxOy e Al2O3 reinforced with NbC, by hidrosilylation reaction between D4Vi and D1107 mixtured with Al2O3 as inert filler, Nb and Al as reactive filler. The specimens produced were pyrolised at 1200, 1250 and 1400°C and infiltred with Al, ICZ and LZSA, respectively. Density, porosity, flexural mechanical strength and fracture surface by scanning electron microscopy were evaluated. The microstructure of the composites was investigated by X-ray diffraction to identify the presence of crystalline phases. The composites presented apparent porosity varying of 31 up to 49% and mechanical flexural strength of 14 up to 34 MPa. The infiltration process improviment of the densification and reduction of the porosity, as well as increased the values of mechanical flexural strength. The obtained phases had been identified as being Al3Nb, NbSi2, Nb5S3, Nb3Si and NbC. The samples that were submitted the infiltration process presented a layer next surface with reduced pores number in relation to the total volume

Ocorrência e tratamento de monogenoides em alevinos de pampo (Trachinotus carolinus) cultivados experimentalmente na região norte do estado de São Paulo

This work had as objective tests therapeutic treatments seeking the monogenea eradication in fingerlings Florida Pompano (Trachinotus carolinus) servants in cage net in the area of Ubatuba, State of São Paulo. The fingerlings presented an accentuated weigh loss and strong discoloration and through observation of scraped of gills under light microscope were identified a high amount of monogenea. Three treatments were tested in form of baths: T1 (fresh water for 5 minutes); T2 (formalin: 1: 1.000 for 20 minutes) and T3: (formalin: 1:4.000 for 30 minutes). The treatments were appraised through scraped of gills, mounted among you laminate and laminulas and observed to the light microscope. It was observed that in the tested conditions all of the treatments were efficient in the elimination of the monogenea without presenting lethality to the fish. The treatment is recommended T I (take a bath in fresh water for 5 minutes) for the facility in the application and for the absence of use of chemical products.

Acessibilidade no ambiente escolar: reflexões com base no estudo de duas escolas municipais de Natal-RN

This work was originated through the results of the analysis of the services for the needs of people with disabilities that were permitted by the physical space of two schools of the municipality of Natal/RN. The general objective/goal was to subsidize the elaboration of alternatives for the planning of environments that could be used by any person. The study used the empirical research through the adoption of a multimethod approach including: (i) technical visits oriented by the NBR 9050, (ii) contact with users that have reduced mobility (visually impaired and wheelchair or crutch users) through escorted travels and interviews, and (iii) interview with school managers. The evidence from the research, even though with significant development of laws that guarantee people with disabilities their right to citizenship, the physical environment of our schools still present with many obstacles that prevent the mobility of people with disabilities which proves their lack of readiness to accommodate them. Therefore, the actions taken to address the accessibility has been the adoption of temporary solutions that makes the adaptation more difficult, adds obstacles and reinforces the undesirable segregation, however still very present in our society. Finally, there is the indication that in order to achieve the spatial configuration that promotes social contact and integration in between the persons with different physical status, it is necessary to completely comprehend the activities developed in each space, from the conception of the equipment to the individual learning needs, having in mind creating environments that stimulates the execution of the tasks in an independent manner without the assistance of others. The inclusion regarding attention to accessibility in the decision making process, directed to the arquitectural and urban project, would decrease the constant need to redevelop and adapt spaces, and should be definitely incorporated as an important component in the production of space

Circuito regional de performance BodeArte: encontros, coletividade e porítica na performance do Rio Grande do Norte

This dissertation aims to look into the structure of the event Circuito Regional de Performance BodeArte1 to think how it collaborate with its proposal providing theoretical points to relevant questions to the comprehension of Brazilian performance art in contemporaneity, since its conceptual format until its occurrence and practical limitations. From this proposition the dissertation is organized into three chapters guided for the following aspects: the resumption of the events encompassed on the occurrence of Circuit BodeArte as well as a tabulation of the data reunited in its history, the presentation of its conceptual choices, and the metaphors conducted by the use of the term performance and how they can lead us to the idea of a performance-as-BodeArte. The methodological structures moved for this organization are qualitative, and have been formed from printed materials, texts, festival programs, blog, videos, photos, interviews, lectures and forums, plus our own memory as a producer and performer of the event, looking through these set points of the epistemological organization contained on the proposal of the Circuito, expanding and discussing them. This way this research moves between the propositions of this event in its three editions, promoting discussions that dialogue with concepts such as the emergence of Steve Johnson (2004), the metaphors of thought proposed by Christine Greiner (2005), the idea of performance hacker of Maria Beatriz de Medeiros (AQUINO, et al., 2012), as well as other propositions presented by Jan Swidzinski (2005) and Eleonora Fabião (2012)

Caracterização limnológica e determinação da capacidade suporte do reservatório mendubim, (Rio Grande do Norte) para o cultivo de peixes em tanques-rede

The aims of this study were: i) assessing the trophic state of the Mendubim reservoir (semi-arid, Rio Grande do Norte, Brazil; 05° 38 99,0 S 36°55 98,0 W) based on chlorophyll-a, total phosphorus and nitrogen concentrations and water transparency; ii) relating the patterns of temporal variation of zooplankton and phytoplankton to the trophic state of the reservoir and iii) investigating the carrying capacity of the reservoir for cage fish farming. The samplingwas done monthly from July 2006 to July 2007 in three stations at the reservoir: next to the dam (barrage), in the central region and in the mouth of the main tributary. The abiotic and biotic variables analyzed were: Secchi depth, volatiles and fixed suspended solids, chlorophyll-a, total phosphorus and nitrogen, TN:TP ratio and mesozooplankton and phytoplankton composition and biomass. The results showed that the reservoir can be considered as mesotrophic with mean concentrations of total nitrogen, phosphorus and chlorophyll-a equal to 1711, 1 μg.L-1, 30,8 μg.L-1 and 5,62 μg.L-1 respectively. The Cyanophyceae class was the most representative in terms of density, with the presence of potentially toxic species such as Microcystis aeruginosa, Planktothrix planctonica, Cylindrospermopsis raciborskii, Aphanizomenon sp. ,Aphanocapsa delicatissima and Pseudanabaena acicularis. Among the zooplankton, the genus Notodiaptomus presented the largest biomass values. Overall, our results show that the light limitation should explain the weak relationship between chlorophyll-a and total phosphorus and nitrogen concentrations. We concluded that the water of Mendubim reservoir is suitable for intensive fish cage aquaculture. Based on the carrying capacity calculations for this reservoir, we found that the maximum sustainable yield of tilapias in cages in the reservoir is 126 ton per year assuming a factor of food conversion of 1.5: 1.0 and a phosphorus content in the fish food of 1%

Estrutura e dinâmica do fitoplânctone bacterioplâncton em cultivos de camarão no Rio Grande do Norte-Brasil: impacto sobre o ambiente natural

This work aimed to study the structure and dynamic of Phytoplankton and Bacterioplankton in a complete cycle of shrimp cultivation (Litopenaeus vannamei) and determine the environmental factors responsible for the structural changes of these communities. The study was realized in a saltwater shrimp farm (Macaíba, RN), between September/2005 and February/2006, and in a freshwater shrimp farm (Ceará Mirim, RN), between May/2007 and September 2007. The samplings were collected weekly in saltwater farm and every fifteen days in freshwater farm. Total phosphorus, chlorophyll a and environmental parameters (pH, dissolved oxygen, salinity, temperature, depth and water transparency) were measured. Qualitative and quantitative analysis of the phytoplankton and bacterioplankton were carried out. The Shannon-Wiener ecologic indexes of diversity and the Pielou equitability indexes were calculated to the phytoplankton. Bacterial density was determined by epifluorescence microscopy. The data were statistically analyzed by Pearson correlation and t-Test. Chlorophycea were predominat in salt water and in the captation/drainage point (24 to 99%). Diatoms had higher wealth. The species Choricystis minor had the highest occurrence (100%) and dominance (90-100%), thus showing its adaptation to the high temperatures, salinity and low water transparency conditions. Filamentous Cyanobacteria like Oscillatoria sp., Pseudoanabaena sp. and Phormidium sp. had constant levels. The negative correlation between chlorophycea and water transparency, and the positive correlation between chlorophyll a and salinity, showed that the phytoplankton was well adapted to the low transparency and to the high salinity. The bacterioplankton was negatively correlated with the total phosphorus and salinity. In freshwater, Cyanobacteria were predominant (>80%), presenting some producers of toxins species like Microcystis sp., Aphanizomenon sp., Cylindrospermopsis raciborskii e Anabaena circinalis. Cyanobacterial density and total phosphorus and chlorophyll a concentrations exceeded the maximum value allowed by legislation. The means of total phosphorus varied from 264 to 627 Wg.L-1 and the means of chlorophyll a oscillated between 22 and 182 Wg.L-1. The phytoplankton species were selected by low availability of the light, high pH, temperature and high availability of total phosphorus. The bacterioplankton showed high densities (5,13 x 107 to 8,50 x107 Bac.mL-1). The studied environments (ponds and rivers) presented a high level of trophic state based on the high concentrations of chlorophyll a and total phosphorus and cyanobacteria dominance. The composition of species in the ponds and rivers was similar, as well as high concentrations of total phosphorus and chlorophyll a, highlighting the pollution caused by the discharges of the farms in natural environment

Contribuição da Geodésia ao monitoramento costeiro do Litoral Setentrional do Rio Grande do Norte, área de influência da indústria petrolífera

The general objective of this thesis has been seasonal monitoring (quarterly time scale) of coastal and estuarine areas of a section of the Northern Coast of Rio Grande do Norte, Brazil, environmentally sensitive and with intense sediment erosion in the oil activities to underpin the implementation of projects for containment of erosion and mitigate the impacts of coastal dynamics. In order to achieve the general objective, the work was done systematically in three stages which consisted the specific objectives. The first stage was the implementation of geodetic reference infrastructure for carrying out the geodetic survey of the study area. This process included the implementation of RGLS (Northern Coast of the RN GPS Network), consisting of stations with geodetic coordinates and orthometric heights of precision; positioning of Benchmarks and evaluation of the gravimetric geoid available, for use in GPS altimetry of precision; and development of software for GPS altimetry of precision. The second stage was the development and improvement of methodologies for collection, processing, representation, integration and analysis of CoastLine (CL) and Digital Elevation Models (DEM) obtained by geodetic positioning techniques. As part of this stage have been made since, the choice of equipment and positioning methods to be used, depending on the required precision and structure implanted, and the definition of the LC indicator and of the geodesic references best suited, to coastal monitoring of precision. The third step was the seasonal geodesic monitoring of the study area. It was defined the execution times of the geodetic surveys by analyzing the pattern of sediment dynamics of the study area; the performing of surveys in order to calculate and locate areas and volumes of erosion and accretion (sandy and volumetric sedimentary balance) occurred on CL and on the beaches and islands surfaces throughout the year, and study of correlations between the measured variations (in area and volume) between each survey and the action of the coastal dynamic agents. The results allowed an integrated study of spatial and temporal interrelationships of the causes and consequences of intensive coastal processes operating in the area, especially to the measurement of variability of erosion, transport, balance and supply sedimentary over the annual cycle of construction and destruction of beaches. In the analysis of the results, it was possible to identify the causes and consequences of severe coastal erosion occurred on beaches exposed, to analyze the recovery of beaches and the accretion occurring in tidal inlets and estuaries. From the optics of seasonal variations in the CL, human interventions to erosion contention have been proposed with the aim of restoring the previous situation of the beaches in the process of erosion.

Influência dos fatores abióticos sobre a variação espaço-temporal de paralonchurus brasiliensis (Steindachner, 1875) (pisces, sciaenidae) componente da fauna acompanhante da pesca de camarões no litoral Norte de São Paulo

Knowledge of the environmental factors influence on the spatial-temporal variation of fishes is important to fisheries management and conservation. Thus, the aim of this work was to analyze the influence of the abiotical factors on the spatial-temporal distribution of Paralonchurus brasiliensis (Pisces, Sciaenidae) caught by-catch with the shrimp fishing of Ubatuba and Caraguatatuba regions, north coast of São Paulo State. The fishes were captured every month from January to December 2002. Samples were collected by otter trawl at 5, 10, 15, 20, 25, 30 and 35m depths. The temperatures (surface and bottom), salinities (surface and bottom), sediment features and organic matters were verified for each depth. During all period of the study 12.642 specimens of P. brasiliensis were captured at Ubatuba and 17.166 at Caraguatatuba, which totalized the biomass of 267 for the first and 339kg for the other region. The females outnumbered males in fish population. The greatest values of biomass and number of individuals were registered at the summer and autumn seasons, while the lowest values were observed at the winter and spring seasons. The greatest abundances were found from 15 to 25m depth. In this study, it was verified that P. brasiliensis is a coastal waters associate species. The spatialtemporal distribution of P. brasiliensis is affected by intrusion of SACW and depth for the coastal region and by depth and sediment in sheltered areas such as Caraguatatuba

Potencialidades de cultivo de macroalgas no litoral do Rio Grande do Norte (NE, Brasil): uma perspectiva de integração de dados ambientais em sistemas de informação geográfica (SIG)

Since centuries ago, the Asians use seaweed as an important source of feeding and are their greatest world-wide consumers. The migration of these peoples for other countries, made the demand for seaweed to increase. This increasing demand prompted an industry with annual values of around US$ 6 billion. The algal biomass used for the industry is collected in natural reservoirs or cultivated. The market necessity for products of the seaweed base promotes an unsustainable exploration of the natural banks, compromising its associated biological balance. In this context, seaweed culture appears as a viable alternative to prevent the depletion of these natural supplies. Geographic Information Systems (GIS) provide space and produce information that can facilitate the evaluation of important physical and socio-economic characteristics for the planning of seaweed culture. This objective of this study is to identify potential coastal areas for seaweed culture in the state of Rio Grande do Norte, from the integration of social-environmental data in the SIG. In order to achieve this objective, a geo-referred database composed of geographical maps, nautical maps and orbital digital images was assembled; and a bank of attributes including physical and oceanographical variables (winds, chains, bathymetry, operational distance from the culture) and social and environmental factors (main income, experience with seaweed harvesting, demographic density, proximity of the sheltered coast and distance of the banks) was produced. In the modeling of the data, the integration of the space database with the bank of attributes for the attainment of the map of potentiality of seaweed culture was carried out. Of a total of 2,011 ha analyzed by the GIS for the culture of seaweed, around 34% or 682 ha were indicated as high potential, 55% or 1,101 ha as medium potential, and 11% or 228 ha as low potential. The good indices of potentiality obtained in the localities studied demonstrate that there are adequate conditions for the installation of seaweed culture in the state of Rio Grande do Norte

Ecologia do fitoplâncton em áreas de cultivo de Tilápia do Nilo, Oreochromis niloticus, em tanques-rede no açude Ministro João Alves, Parelhas, Rio Grande do Norte

The dams are limnic ecosystems of great importance for its multiple uses, among them, water supply for the public and to culture of artisanal fish are most relevant. The aim of the present study is to evaluate the physical-chemical characteristics and the phytoplankton community in two chosen sites (Point 1 littoral zone of point source; Point 2 pelagic zone of non-point source) of the Minister João Alves dam, which is also known as Boqueirão de Parelhas/RN. This represents the spatial distribution of the phytoplankton species in order to understand any possible alterations of the water quality and the phytoplankton composition in relation to the water quality originating from the impact of the tilapia, Oreochromis niloticus, culture. The study period also encompasses temporal variations exhibited in two seasons of an annual cycle, one during the dry season (Oct, Nov and Dec of 2008 and Jan of 2009), and the other rainy season (Mar, Apr, May and June of 2008) to extend the observation. The physicalchemical parameters, such as pH, temperature, electrical conductivity, concentration of dissolved oxygen were measured in situ and the values of the inorganic nutrients (nitrate, ammonium and orto-phosfato) and chlorophyll in the laboratory. The quali-quantitative analyses of the phytoplankton had been carried through sedimentation technique and the enumeration of the random of 400 cells, colonies and filaments counted using Sedgwick-Rafter counting chamber. The results of pH varied widely from the acidic to alkaline range with the minimum of 5.8 (± 0.8) and the maximum of 9.2 (± 0.7-0.8), at point 1 and 2. The dissolved oxygen content was higher in the rainy period than that in the dry period. The maximum electrical conductivity was of 1409 μScm-1 in point 1 and 431 minim of μScm-1, in point 2. There was a considerable alteration in the levels of inorganic nutrients such as nitrate-nitrogen, ammoniacal nitrogen and orthophosphate during the two cycles of study period. Phytoplankton assemblages presented a picture of alternate dominance among species Cyanobacteria, Bacillariophyceae and Chlorophyceae. The trophic state index diagnosed to the category of mesotrophic, which is based on the values of chlorophyll, total phosphorus and Secchi-disc measurements. The wind driven turbulence of the water column and the fresh inflow of water (flushing and dilution) during rainy season acted as constraint and did-not allow an exaggerated growth of the species of cyanobacteria. On the basis of the present we conclude that the culture of tilapias in cage-culture fails to produce pollution load that could compromise the quality of the water of the dam, probably be due to small dimension of the culture in relation to the size, volume of the water and the reservoir capacity support its own environment

Contributo para a caracterização morfométrica da raça de abelhas melíferas (Apis mellifera iberiensis) da região norte de Portugal

A necessidade de aprofundar o conhecimento sobre a morfologia da abelha melífera portuguesa (Apis mellifera iberiensis) originou o presente estudo. A amostragem definiu-se com base no banco de amostras existentes no Laboratório de Patologia Apícola da ESA-IPB, relativas ao ano de 2015. Cada amostra foi constituída por cinco obreiras adultas conservadas pelo frio (-18 °C). Foram analisadas 124 amostras distribuídas por 16 concelhos (aproximadamente oito por concelho) pertencentes aos distritos de Bragança e Vila Real. As medições efetuadas em cada uma das obreiras foram: peso (PA), comprimento (CA) e largura (LA) do corpo; comprimento (CAA) e largura (LAA) da asa anterior; comprimento (CAP) e largura da asa posterior (LAP); comprimento do fêmur (CF), da tíbia (CT), do basitarso (CBT), do tarso (CTA) e da probóscide (CP) e a largura do basitarso (LBT). Para avaliação destas medidas utilizou-se uma balança analítica de precisão (0,01g) e um paquímetro eletrónico digital (0-100mm±0,02mm). As diferentes variáveis estudadas compararam-se por análise de variância (ANOVA), sendo o teste de Tukey-Kramer HSD utilizado para a comparação múltipla de médias. O peso médio das obreiras do concelho de Vila Pouca de Aguiar (0,123±0,018 g) foi mais elevado (p<0,05) do que o das obreiras dos concelhos de Torre de Moncorvo e Ribeira de Pena (0,106±0,023 g em ambos os casos). Também, as obreiras do concelho de Vila Pouca de Aguiar apresentaram um comprimento médio do corpo (13,065±0,890 mm) superior (p<0,05) às obreiras do concelho de Boticas (12,228±0,958 mm) e uma largura média (4,565 ± 0,392 mm) superior às obreiras de Vila Flor (4,089 ±0,288 mm). Porém, o CAP (6,333±0,303 mm) e o CT (3,179±0,183mm) das obreiras de Vila Pouca de Aguiar foi mais baixo (p<0,05) ao observado nos concelhos de Torre de Moncorvo (6,616±0,361 mm) e Vila Flor (3,358±0,146 mm). As variáveis LAA, LAP, CF, CBT e CP não apresentaram diferenças significativas (p>0,05) entre os concelhos estudados.

Divergência genética em genótipos de maracujazeiro azedo, com base em características físicas e químicas dos frutos.

RESUMO: Objetivou-se com o presente trabalho avaliar a divergência genética e as características físicas e químicas de frutos de duas populações do maracujazeiro azedo na região Norte do Espírito Santo, como as progênies de meio-irmãos de acesso local de um plantio comercial (genótipos: 1; 2; 3; 4; 5; 6; 7; 8; 9 e 10) e do híbrido BRS Ouro Vermelho (genótipos: 11; 12; 13; 14; 15; 16; 17; 18; 19 e 20). A divergência genética foi avaliada por procedimentos multivariados como a distância generalizada de Mahalanobis (D2) e pelos métodos de agrupamento de otimização de Tocher e UPGMA. Encontrou-se divergência genética entre as populações estudadas promovendo a formação de grupos diferentes entre o método de Tocher e do UPGMA. As características, referentes ao tamanho do fruto, diâmetro polar e equatorial, foram as que mais contribuíram na diversidade genética dos genótipos. Nas populações estudadas de maracujazeiro azedo há grande variabilidade genética quanto às características avaliadas, o que possibilita selecionar plantas com elevado potencial para fins de melhoramento genético. O híbrido BRS Ouro Vermelho apresenta boa adaptação às condições locais. ABSTRACT: The aim of the present work was to evaluate genetic divergence and physical and chemical characteristics in fruit of two populations of sour passion fruit in the northern region of the State of Espírito Santo, Brazil, these being half-sibling progenies from local accessions of a commercial crop (genotypes 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10) and the hybrid BRS Ouro Vermelho (genotypes: 11, 12, 13, 14, 15, 16, 17, 18, 19 and 20). Genetic divergence was evaluated using such multivariate procedures as the generalised Mahalanobis distance (D2) and the Tocher optimisation and UPGMA clustering methods. Genetic divergence was found between the populations under study, promoting the formation of different groups between the Tocher and UPGMA methods. As characteristics for fruit size, the polar and equatorial diameters had the most impact on the genetic diversity of the genotypes. In the populations of sour passion fruit being studied, great genetic variability is seen in the evaluated characteristics, making it possible to select plants of high potential for breeding purposes. The BRS Ouro Vermelho hybrid is well adapted to the local conditions.