Spectroscopic monitoring during laser welding of aluminium alloy

The mechanical properties of aluminium alloys are strongly influenced by the alloying elements and their concentration. In the case of aluminium alloy EN AW-6060 the main alloying elements are magnesium and silicon. The first goal of this thesis was to determine stability, repeatability and sensitivity as figures of merit of the in-situ melt identification technique. In this study the emissions from the laser welding process were monitored with a spectrometer. With the information produced by the spectrometer, quantitative analysis was conducted to determine the figures of merit. The quantitative analysis concentrated on magnesium and aluminium emissions and their relation. The results showed that the stability of absolute intensities was low, but the normalized magnesium emissions were quite stable. The repeatability of monitoring magnesium emissions was high (about 90 %). Sensitivity of the in-situ melt identification technique was also high. As small as 0.5 % change in magnesium content was detected by the spectrometer. The second goal of this study was to determine the loss of mass during deep penetration laser welding. The amount of magnesium in the material was measured before and after laser welding to determine the loss of magnesium. This study was conducted for aluminium alloy with nominal magnesium content of 0-10 % and for standard material EN AW-6060 that was welded with filler wire AlMg5. It was found that while the magnesium concentration in the material changed, the loss of magnesium remained fairly even. Also by feeding filler wire, the behaviour was similar. Thirdly, the reason why silicon had not been detected in the emission spectrum needed to be explained. Literature research showed that the amount of energy required for silicon to excite is considerably higher compared to magnesium. The energy input in the used welding process is insufficient to excite the silicon atoms.

Spatial variability of leaf nutrient contents in a drip irrigated citrus orchard

This study aimed to evaluate the spatial variability of leaf content of macro and micronutrients. The citrus plants orchard with 5 years of age, planted at regular intervals of 8 x 7 m, was managed under drip irrigation. Leaf samples were collected from each plant to be analyzed in the laboratory. Data were analyzed using the software R, version 2.5.1 Copyright (C) 2007, along with geostatistics package GeoR. All contents of macro and micronutrients studied were adjusted to normal distribution and showed spatial dependence.The best-fit models, based on the likelihood, for the macro and micronutrients were the spherical and matern. It is suggest for the macronutrients nitrogen, phosphorus, potassium, calcium, magnesium and sulfur the minimum distances between samples of 37; 58; 29; 63; 46 and 15 m respectively, while for the micronutrients boron, copper, iron, manganese and zinc, the distances suggests are 29; 9; 113; 35 and 14 m, respectively.

Improving the competitiveness of electrolytic Zinc process by chemical reaction engineering approach

This doctoral thesis describes the development work performed on the leachand purification sections in the electrolytic zinc plant in Kokkola to increase the efficiency in these two stages, and thus the competitiveness of the plant. Since metallic zinc is a typical bulk product, the improvement of the competitiveness of a plant was mostly an issue of decreasing unit costs. The problems in the leaching were low recovery of valuable metals from raw materials, and that the available technology offered complicated and expensive processes to overcome this problem. In the purification, the main problem was consumption of zinc powder - up to four to six times the stoichiometric demand. This reduced the capacity of the plant as this zinc is re-circulated through the electrolysis, which is the absolute bottleneck in a zinc plant. Low selectivity gave low-grade and low-value precipitates for further processing to metallic copper, cadmium, cobalt and nickel. Knowledge of the underlying chemistry was poor and process interruptions causing losses of zinc production were frequent. Studies on leaching comprised the kinetics of ferrite leaching and jarosite precipitation, as well as the stability of jarosite in acidic plant solutions. A breakthrough came with the finding that jarosite could precipitate under conditions where ferrite would leach satisfactorily. Based on this discovery, a one-step process for the treatment of ferrite was developed. In the plant, the new process almost doubled the recovery of zinc from ferrite in the same equipment as the two-step jarosite process was operated in at that time. In a later expansion of the plant, investment savings were substantial compared to other technologies available. In the solution purification, the key finding was that Co, Ni, and Cu formed specific arsenides in the “hot arsenic zinc dust” step. This was utilized for the development of a three-step purification stage based on fluidized bed technology in all three steps, i.e. removal of Cu, Co and Cd. Both precipitation rates and selectivity increased, which strongly decreased the zinc powder consumption through a substantially suppressed hydrogen gas evolution. Better selectivity improved the value of the precipitates: cadmium, which caused environmental problems in the copper smelter, was reduced from 1-3% reported normally down to 0.05 %, and a cobalt cake with 15 % Co was easily produced in laboratory experiments in the cobalt removal. The zinc powder consumption in the plant for a solution containing Cu, Co, Ni and Cd (1000, 25, 30 and 350 mg/l, respectively), was around 1.8 g/l; i.e. only 1.4 times the stoichiometric demand – or, about 60% saving in powder consumption. Two processes for direct leaching of the concentrate under atmospheric conditions were developed, one of which was implemented in the Kokkola zinc plant. Compared to the existing pressure leach technology, savings were obtained mostly in investment. The scientific basis for the most important processes and process improvements is given in the doctoral thesis. This includes mathematical modeling and thermodynamic evaluation of experimental results and hypotheses developed. Five of the processes developed in this research and development program were implemented in the plant and are still operated. Even though these processes were developed with the focus on the plant in Kokkola, they can also be implemented at low cost in most of the zinc plants globally, and have thus a great significance in the development of the electrolytic zinc process in general.

Effect of blanching time on selective mineral elements extraction from the spinach substitute (Tetragonia expansa) commonly used in Brazil

The true spinach (Spinacia oleracea) does not grow well in warm climates and for that reason is not commercialized in Brazil. Instead, a spinach substitute (Tetragonia expansa), originally from New Zealand, is widely used in the country. There is scant information on the mineral profile and none on the soluble mineral fraction of this vegetable. The solubility of a mineral is one of the important factors for its absorption. For this reason, the calcium, magnesium, iron, manganese, copper, zinc, potassium, and sodium soluble fractions in the raw spinach substitute were determined and the effect of blanching times on the solubility of these minerals was investigated. Blanching times of 1, 5, and 15 minutes were employed. The magnesium, manganese, potassium, and sodium soluble fractions increased sizably with shorter blanching time. Longer blanching time (15 minutes) caused large losses of minerals. The soluble mineral fractions can contribute poorly to diet in terms of potassium, magnesium, manganese, and zinc. The spinach substitute cannot be considered a dietary source of calcium, iron and copper due to the insolubility of these minerals in the vegetable, possibly caused by the large oxalate content.

Effects of nickel on the mineral composition of Fleischmann’s yeast (Saccharomyces cerevisiae)

Sugar cane juice containing 12% (w.w -1) of total reducing sugars and 0.0 to 5.0 mmol of nickel L-1, with pH ranging from 3.5 to 6.5, was inoculated with Fleischmann’s yeast (Saccharomyces cerevisiae) (10% w.w -1). Six hours after fermentation, the yeast’s cellular viability and trehalose content were evaluated. The resulting must was centrifuged and the raw yeast was analyzed by atomic absorption spectroscopy to evaluate the intracellular levels of calcium, copper, iron, magnesium, manganese, nickel, phosphorus, potassium, sulfur and zinc. The intracellular levels of iron, magnesium and calcium were affected and the yeast’s susceptibility to nickel was enhanced by the decrease in pH. The yeast’s growth was not affected by nickel at high pH, but the toxic effects of nickel were potentiated at low pH.

Chemical characteristics of pequi fruits (Caryocar brasiliense Camb.) native of three municipalities in the State of Goiás - Brazil

In order to assure that the use of cerrado fruits occur in a sustainable way, studies to investigate their characteristics are extremely relevant. In this context, the present study aims to describe some chemical parameters of pequi fruits picked in three municipalities in southwestern Goiás State (Jataí, Rio Verde, and Serranópolis). In each city, two populations of pequi trees - pequizeiros, denominated areas, were selected. In each area, eight trees were selected for the fruit to be picked. The contents of phosphorus, potassium, calcium, magnesium, nitrogen, zinc, and ether extract were determined in the samples. The results demonstrate differences between the chemical characteristics studied for the fruits picked in different areas, which does not seem to vary in a significant way. Comparing the contents obtained in the present study with those required as human daily supply, further studies are recommended aiming at using the pequi fruit as a complementary alternative source of magnesium, manganese, and copper.

Development and chemical characterization of flour obtained from the external mesocarp of "pequizeiro" fruit

The objective of this work was to develop a recommendation for the chemical peeling of pequi fruit and characterize the flour obtained from the external mesocarp of "Pequizeiro", pequi tree (Caryocar brasiliense Camb.). The technology applied to obtain the external mesocarp pequi flour included the epicarp removal with NaOH solution. The Response Surface Method was used to optimize the chemical peeling process by applying the Central Composite Rotatable Design, with eleven trials including three replicates at the central point, varying the NaOH aqueous solution concentration and fruit immersion time. The mass loss was evaluated through the analysis of variance and using bi and three dimensional graphs. The chemical characteristics of the external mesocarp pequi flour evaluated were: moisture content, ashes, proteins, lipids, total carbohydrates, dietary fiber, and some minerals. The best combination for an efficient removal of the fruit peel with the lowest mass loss was reached with 7.05 minutes of immersion in a 5.08 g.L-1 NaOH aqueous solution. This study indicated that the external mesocarp pequi flour is a food source rich in dietary fiber, carbohydrates, ashes, magnesium, calcium, manganese, and copper, but it is poor in lipids, zinc, and iron.

Chemical characterization of leaves of organically grown carrot Dacus carota L.) in various stages of development for use as food

In Brazil, street markets and vegetable distributors discard vegetable leaves and stems, including those of carrot (Dacus carota L.). Seeking to reduce the waste of vegetable parts, this study characterized chemically the leaves of organically grown carrot in three stages of development to determine the best time for their removal and consumption as food. The leaves were dehydrated in an oven at 70 °C for 43 hours and analyzed for chemical composition, antioxidant activity, chlorophyll content, fatty acid composition, and also calcium (Ca), sodium (Na), potassium (K), magnesium (Mg), manganese (Mn), iron (Fe), zinc (Zn), and copper (Cu) contents. The analyses indicated 100 days of development as the ideal stage for the removal and consumption of carrot leaves with good antioxidant activity requiring only 63.78 ± 0.5 mg.L-1 methanol leaf extract to inhibit 50% of the concentration of the free radical DPPH (2,2-diphenyl-1picrilidrazil), and total protein and alpha-linolenic acid (18:3 n-3/LNA) contents of 18.23% ± 2.8 and 876.55 ± 20.62 mg.100 g-1 of dry matter, respectively.

Physicochemical properties and mineral and protein content of honey samples from Ceará state, Northeastern Brazil

This study evaluated the physicochemical properties and protein and mineral content of honey samples from Ceará State, Northeastern Brazil, one of the major honey exporters in the country. Nutritional importance of the minerals detected was also analyzed. Physicochemical properties were examined according to the AOAC and CAC official methods; the protein content was determined using the Bradford method, and the minerals were analyzed by atomic absorption spectrometry. All analyses were performed in triplicate. The levels of macrominerals sodium (Na), potassium (K), calcium (Ca), and magnesium (Mg) varied from 1.80-47.20, 21.30-1513.30, 14.58-304.82, and 2.48-28.33 mg/kg, respectively, and the trace elements iron (Fe), copper (Cu), manganese (Mn), zinc (Zn), selenium (Se), and chromium (Cr) varied from 0.12-8.76, 0.07-1.29, 0.06-1.96, 0.07-1.85 mg/kg, 0.36 × 10-3-62.00 × 10-3 and 22.50 × 10-3-170.33 × 10-3 µg/kg, respectively. Myracrodruon urundeuva honey sample had high contents of macrominerals (Na, K, Ca, and Mg). Protein content of the Anacardium occidentale honey sample was the highest (1121.00 µg/g) among the samples analyzed. Among the minerals detected in the honey samples, K showed the highest concentration, followed by Ca, Na, and Mg. The presence of trace elements can show environmental contamination. The honey samples studied were free of trace elements contamination, except for Mn; the Piptadenia moniliformis was the only honey sample that was in compliance with the law requirements. The variations of the chemical constituents in the honey samples are probably related to differences in the floral origin and mineral and protein contents and confirm the nutritional importance of Ceará State honey.

Production of magnesium carbonates from serpentinites for CO2 mineral sequestration : optimisation towards industrial application

Global warming is one of the most alarming problems of this century. Initial scepticism concerning its validity is currently dwarfed by the intensification of extreme weather events whilst the gradual arising level of anthropogenic CO2 is pointed out as its main driver. Most of the greenhouse gas (GHG) emissions come from large point sources (heat and power production and industrial processes) and the continued use of fossil fuels requires quick and effective measures to meet the world’s energy demand whilst (at least) stabilizing CO2 atmospheric levels. The framework known as Carbon Capture and Storage (CCS) – or Carbon Capture Utilization and Storage (CCUS) – comprises a portfolio of technologies applicable to large‐scale GHG sources for preventing CO2 from entering the atmosphere. Amongst them, CO2 capture and mineralisation (CCM) presents the highest potential for CO2 sequestration as the predicted carbon storage capacity (as mineral carbonates) far exceeds the estimated levels of the worldwide identified fossil fuel reserves. The work presented in this thesis aims at taking a step forward to the deployment of an energy/cost effective process for simultaneous capture and storage of CO2 in the form of thermodynamically stable and environmentally friendly solid carbonates. R&D work on the process considered here began in 2007 at Åbo Akademi University in Finland. It involves the processing of magnesium silicate minerals with recyclable ammonium salts for extraction of magnesium at ambient pressure and 400‐440⁰C, followed by aqueous precipitation of magnesium in the form of hydroxide, Mg(OH)2, and finally Mg(OH)2 carbonation in a pressurised fluidized bed reactor at ~510⁰C and ~20 bar PCO2 to produce high purity MgCO3. Rock material taken from the Hitura nickel mine, Finland, and serpentinite collected from Bragança, Portugal, were tested for magnesium extraction with both ammonium sulphate and bisulphate (AS and ABS) for determination of optimal operation parameters, primarily: reaction time, reactor type and presence of moisture. Typical efficiencies range from 50 to 80% of magnesium extraction at 350‐450⁰C. In general ABS performs better than AS showing comparable efficiencies at lower temperature and reaction times. The best experimental results so far obtained include 80% magnesium extraction with ABS at 450⁰C in a laboratory scale rotary kiln and 70% Mg(OH)2 carbonation in the PFB at 500⁰C, 20 bar CO2 pressure for 15 minutes. The extraction reaction with ammonium salts is not at all selective towards magnesium. Other elements like iron, nickel, chromium, copper, etc., are also co‐extracted. Their separation, recovery and valorisation are addressed as well and found to be of great importance. The assessment of the exergetic performance of the process was carried out using Aspen Plus® software and pinch analysis technology. The choice of fluxing agent and its recovery method have a decisive sway in the performance of the process: AS is recovered by crystallisation and in general the whole process requires more exergy (2.48–5.09 GJ/tCO2sequestered) than ABS (2.48–4.47 GJ/tCO2sequestered) when ABS is recovered by thermal decomposition. However, the corrosive nature of molten ABS and operational problems inherent to thermal regeneration of ABS prohibit this route. Regeneration of ABS through addition of H2SO4 to AS (followed by crystallisation) results in an overall negative exergy balance (mainly at the expense of low grade heat) but will flood the system with sulphates. Although the ÅA route is still energy intensive, its performance is comparable to conventional CO2 capture methods using alkanolamine solvents. An energy‐neutral process is dependent on the availability and quality of nearby waste heat and economic viability might be achieved with: magnesium extraction and carbonation levels ≥ 90%, the processing of CO2‐containing flue gases (eliminating the expensive capture step) and production of marketable products.

Arsenic and germanium determination by hydride generation in the D.C. plasma optical emission spectrometer

Modifications to the commercial hydride generator, manufactured by Spectrametrics, resulted in improved operating procedure and enhancement of the arsenic and germanium signals. Experiments with arsenic(III) and arsenic(V) showed that identical reiults could be produced from both oxidation states. However, since arsenic(V) is reduced more slowly than arsenic(III), peak areas and not peak heights must be measured when the arsine is immediately stripped from the system (approximately 5 seconds reaction). When the reduction is allowed to proceed for 20 seconds before the arsine is stripped, peak heights may be used. For a 200 ng/mL solution, the relative standard deviation is 2.8% for As(III) and 3.8% for As(V). The detection limit for arsenic using the modified system is 0.50 ng/mL. Studies performed on As(V) standards show that the interferences from 1000 mg/L of nickel(II), cobalt(II), iron(III), copper(II), cadmium(II), and zinc(II) can be eliminated with the aid of 5 M Hel and 3% L-cystine. Conditions for the reduction of germanium to the corresponding hydride were investigated. The effect of different concentrations of HCl on the reduction of germanium to the covalent hydride in aqueous media by means of NaBH 4 solutions was assessed. Results show that the best response is accomplished at a pH of 1.7. The use of buffer solutions was similarly characterized. In both cases, results showed that the element is best reduced when the final pH of the solution after reaction is almost neutral. In addition, a more sensitive method, which includes the use of (NH4)2S208' has been developed. A 20% increase in the germanium signal is registered when compared to the signal achieved with Hel alone. Moreover, under these conditions, reduction of germanium could be accomplished, even when the solution's pH is neutral. For a 100 ng/mL germanium standard the rsd is 3%. The detection limit for germanium in 0.05 M Hel medium (pH 1.7) is 0.10 ng/mL and 0.09 ng/mL when ammonium persulphate is used in conjunction with Hel. Interferences from 1000 mg/L of iron(III), copper(II), cobalt(II), nickel(II), cadmium(II), lead(II), mercury(II), aluminum(III), tin(IV), arsenic(III), arsenic(V) and zinc(II) were studied and characterized. In this regard, the use of (NH4)ZS20S and Hel at a pH of 1.7 proved to be a successful mixture in the sbppression of the interferences caused by iron, copper, aluminum, tin, lead, and arsenic. The method was applied to the determination of germanium in cherts and iron ores. In addition, experiments with tin(IV) showed that a 15% increase in the tin signal can be accomplished in the presence of 1 mL of (NH4)2S20S 10% (m/V).

Experimental and Computational Studies on Copper and Hydrobenzoin Derivatives in Catalytic Asymmetric Reactions

The use of theory to understand and facilitate catalytic enantioselective organic transformations involving copper and hydrobenzoin derivatives is reported. Section A details the use of theory to predict, facilitate, and understand a copper promoted amino oxygenation reaction reported by Chemler et al. Using Density Functional Theory (DFT), employing the hybrid B3LYP functional and a LanL2DZ/6-31G(d) basis set, the mechanistic details were studied on a N-tosyl-o-allylaniline and a [alpha]-methyl-[gamma]-alkenyl sulfonamide substrate. The results suggest the N-C bond formation proceeds via a cisaminocupration, and not through a radical-type mechanism. Additionally, the origin of diastereoselection observed with [alpha]-methyl-[gamma]-alkenyl sulfonamide arises from avoidance of unfavourable steric interactions between the methyl substituent and the N -protecting group. Section B details the computationally guided, experimental investigation of two hydrobenzoin derivatives as ligands/ catalysts, as well as the attempted synthesis of a third hydrobenzoin derivative. The bis-boronic acid derived from hydrobenzoin was successful as a Lewis acid catalyst in the Bignielli reaction and the Conia ene reaction, but provided only racemic products. The chiral diol derived from hydrobenzoin successfully increased the rate of the addition of diethyl zinc to benzaldehyde in the presence of titanium tetraisopropoxide, however poor enantioinduction was obseverved. Notably, the observed reactivity was successfully predicted by theoretical calculations.

Polymérisation du lactide par des catalyseurs β-diketiminate de zinc et de magnésium

Les images de molécules ont été dessinées avec le logiciel Chemdraw version 11.0

The Technology of Copper Alloys, Particularly Leaded Bronze, in Greece, its Colonies, and in Etruria during the Iron Age

L’objet de la présente étude est le développement, l’application et la diffusion de la technologie associée à divers types d’alliages de cuivre, en particulier l’alliage du plomb-bronze, en Grèce ancienne, dans ses colonies, ainsi qu’en Étrurie. Le plomb-bronze est un mélange de diverses proportions d’étain, de cuivre et de plomb. Le consensus général chez les archéométallurgistes est que le plomb-bronze n’était pas communément utilisé en Grèce avant la période hellénistique; par conséquent, cet alliage a reçu très peu d’attention dans les documents d’archéologie. Cependant, les analyses métallographiques ont prouvé que les objets composés de plomb ajouté au bronze ont connu une distribution étendue. Ces analyses ont aussi permis de différencier la composition des alliages utilisés dans la fabrication de divers types de bronzes, une preuve tangible que les métallurgistes faisaient la distinction entre les propriétés du bronze d’étain et celles du plomb-bronze. La connaissance de leurs différentes caractéristiques de travail permettait aux travailleurs du bronze de choisir, dans bien des cas, l’alliage approprié pour une utilisation particulière. L’influence des pratiques métallurgiques du Proche-Orient a produit des variations tant dans les formes artistiques que dans les compositions des alliages de bronze grecs durant les périodes géométrique tardive et orientalisante. L’utilisation du plomb-bronze dans des types particuliers d’objets coulés montre une tendance à la hausse à partir de la période orientalisante, culminant dans la période hellénistique tardive, lorsque le bronze à teneur élevée en plomb est devenu un alliage commun. La présente étude analyse les données métallographiques de la catégorie des objets coulés en bronze et en plomb-bronze. Elle démontre que, bien que l’utilisation du plomb-bronze n’était pas aussi commune que celle du bronze d’étain, il s’agissait néanmoins d’un mélange important d’anciennes pratiques métallurgiques. Les ères couvertes sont comprises entre les périodes géométrique et hellénistique.

Studies on ecophysiology of pfnafus indicus h. milne edwards in the grow-out system

In the present study, the main emphasis was to find out it seasonal and ecosystem specific variations of calcium magnesium, phosphorus, copper and zinc in the water and the sediment has any role to play in altering the concentration of these elements in different tissues of intermoult p.indicus as evidenced by the seasonal studies in the grow out and the marine ecosystems