Physical, chemical, and biological characterization of water year types in the San Francisco Bay estuary [abstract]

EXTRACT (SEE PDF FOR FULL ABSTRACT): Twenty-three years of physical, chemical, and biological data were used to characterize conditions associated with wet, normal, dry, and critical water year types in the upper San Francisco Bay estuary.

The influence of climate on phytoplankton communities in the upper San Francisco estuary

EXTRACT (SEE PDF FOR FULL ABSTRACT): The 1977 climate shift was characterized by low chlorophyll a concentrations and a shift in phytoplankton community composition throughout the upper San Francisco Bay estuary. ... For climate to be a driving force in phytoplankton communities, it must affect mechanisms that control biomass and community composition. The influence of climate on environmental conditions and phytoplankton community composition among water-year types was examined using 19 years of physical, chemical, and phytoplankton data collected monthly at 15 stations throughout the estuary.

Prawn seed resources and its farming potentialities in Sunkeri back waters (Kali Estuary - Karwar)

Prawn seed resources of Sunkeri back waters indicated the availability of Penaeus indicus, P. monodon, Metapenaeus dobsoni and M. monoceros. The monthly variation in seed composition, its correlation with environmental parameters and the aquaculture potentialities are reported

Tidal and diel influence on zooplankton occurrence in the Mandovi estuary, Goa

Distribution and abundance of zooplankton over the tidal cycle were studied in the Mandovi estuary, Goa, during August and December 1971 and May 1972. Tide induced salinity fluctuations were obvious with high values during spring tides. Salinity was low during August, apparently due to precipitation and land run off but increased subsequently. The mean biomass values for the day and night collections were 13.6 and 19.8 ml/100 m super(3) respectively. Occurrence of most of the zooplankton taxa and species was related to diel rhythm and tidal oscillations. However, overall mean zooplankton standing stock at both the stations were same (16.3 ml/100 m super(3)) indicating that estuarine zooplankton maintained their position during tidal exchanges. Variations in occurrence of common groups and species of zooplankton over the tidal cycle are discussed.

Environmental inventory and the distribution of inorganic nutrients in a tropical estuary of the south-west coast of India

Dissolved nutrients (PO sub(4)-P, NO sub(3)-N, NO sub(2)-N and SiO sub(4)-Si) estimated in the surface and bottom waters of five selected stations of the Paravur Lake, Kerala, India, during February 1987 to January 1988 revealed distinct seasonal variations. Rainfall and land drainage play significant roles in the nutrient economy, particularly NO sub(3)-N and SiO sub(4)-Si, of this water body. Abnormally high values of PO sub(4)-P indicated extremely polluted condition at the wetting zone of the lake during the premonsoon season. SiO sub(4)-Si showed significant negative relationship with salinity.

Seasonal variation in the physico-chemical properties of Rushikulya estuary and its effect on the occurrence of Chanos fry

Seasonal variation in some physico-chemical properties of Rushikulya estuary was studied. The surface water temperature varied from 20 to 34.5 degree C, the transparency of the water from 6.3 to 12 cm, the salinity from 28.3 to 32.8 % and the pH from 6.77 to 7.35. The transparency and salinity showed bimodal distribution. Occurrence of the Chanos fry were correlated to it.

Biology of Balanus amphitrite communis (Darwin) in the Cochin harbour waters

Seasonal viariations in the incidence on fresh surfaces, breeding season, rate of growth and mortality of Balanus amphitrite communis was studied for a period of twelve months in the Cochin harbour waters, situated 76̊ 14'E and 90̊ 57'N, and subjected to annual seasonal changes in salinity.

An investigation into the residual stresses in an aluminium 2024 test weld

This paper uses finite element (FE) analysis to examine the residual stresses generated during the TIG welding of aluminium aerospace alloys. It also looks at whether such an approach could be useful for evaluating the effectiveness of various residual stress control techniques. However, such simulations cannot be founded in a vacuum. They require accurate measurements to refine and validate them. The unique aspect of this work is that two powerful engineering techniques are combined: FE modelling and neutron diffraction. Weld trials were performed and the direct measurement of residual strain made using the ENGIN neutron diffraction strain scanning facility. The predicted results show an excellent agreement with experimental values. Finally this model is used to simulate a weld made using a "Low Stress No Distortion" (LSND) technique. Although the stress reduction predicted is only moderate, the study suggests the approach to be a quick and efficient means of optimising such techniques.

The Sundarbans fishers coping in an overly stressed mangrove estuary

The fishing community of the Sundarbans are the human group most at home in the mud-slush-water-forest environment of this famous mangrove estuary. Their skills, knowledge, and technique have developed in response to a challenging environment. Yet, of the countless studies on the various aspects of this eco-region, there are exceedingly few that have studied the Sundarbans fisher in his/her ecological, historical and demographic context—as a key stakeholder in an environment under considerable stress. The present study seeks to reduce this lacuna a little. Its object is not merely to examine and analyse, but also to identify means, both tradition-based and innovative, which might contribute to protect the environment, improve economic conditions, and usher in people-based governance of resources.

Friction and material transfer in micro-scale sliding contact between aluminium alloy and steel

A ball-on-flat reciprocating micro-tribometer has been used to measure the friction coefficient between aluminium alloy strip and a steel ball. A relatively small ball and correspondingly low contact load is used to give a contact width of the order of 100μm, closer to asperity contact widths than generally found for this type of test. The effects of load, initial strip surface roughness, lubricants and boundary additives are investigated. It is found that the friction coefficient is significantly reduced by the addition of a lubricant. Observations of the wear tracks and ball surface show that the material transfer from aluminium to the ball is reduced in the presence of the lubricant. The initial friction coefficient is further reduced by the addition of a boundary additive, but the friction coefficient after 8 cycles is unchanged. Copyright © 2004 by Springer Science+Business Media, Inc.

Distribution of mercury in a tropical estuary (India) situated near a chloro-alkali plant

The distribution of mercury in water, sediment and some biological samples of the Rushikulya estuary, east coast of India were assessed during Jan-Dec. 1989. Both the dissolved plus acid leachable mercury contents in water and the sediment mercury discerned conspicuous spatial and seasonal fluctuations. Adsorption on to the suspended particulates was found to be the most likely mechanism for removal of mercury from the water column. Exchange of mercury from sediments to water was observed at high salinities (20-30x10-3). The residual mercury contents in the biological samples revealed that bio-accumulation by bottom-dwelling organisms are higher than the pelagic components.

Assessing the potential of yield improvements, through process scrap reduction, for energy and CO2 abatement in the steel and aluminium sectors

Targets to cut 2050 CO2 emissions in the steel and aluminium sectors by 50%, whilst demand is expected to double, cannot be met by energy efficiency measures alone, so options that reduce total demand for liquid metal production must also be considered. Such reductions could occur through reduced demand for final goods (for instance by life extension), reduced demand for material use in each product (for instance by lightweight design) or reduced demand for material to make existing products. The last option, improving the yield of manufacturing processes from liquid metal to final product, is attractive in being invisible to the final customer, but has had little attention to date. Accordingly this paper aims to provide an estimate of the potential to make existing products with less liquid metal production. Yield ratios have been measured for five case study products, through a series of detailed factory visits, along each supply chain. The results of these studies, presented on graphs of cumulative energy against yield, demonstrate how the embodied energy in final products may be up to 15 times greater than the energy required to make liquid metal, due to yield losses. A top-down evaluation of the global flows of steel and aluminium showed that 26% of liquid steel and 41% of liquid aluminium produced does not make it into final products, but is diverted as process scrap and recycled. Reducing scrap substitutes production by recycling and could reduce total energy use by 17% and 6% and total CO 2 emissions by 16% and 7% for the steel and aluminium industries respectively, using forming and fabrication energy values from the case studies. The abatement potential of process scrap elimination is similar in magnitude to worldwide implementation of best available standards of energy efficiency and demonstrates how decreasing the recycled content may sometimes result in emission reductions. Evidence from the case studies suggests that whilst most companies are aware of their own yield ratios, few, if any, are fully aware of cumulative losses along their whole supply chain. Addressing yield losses requires this awareness to motivate collaborative approaches to improvement. © 2011 Elsevier B.V. All rights reserved.

The characteristics of distribution and change of the seawater temperature and salinity of Cai river estuary and Northern Part of Nha Trang bay in the dry and rainy season

In this paper, some results of analyzing the hydrographic characteristics of the seawater temperature and salinity are presented. The received results showed that: in dry season, the influence of the Cai river water has is limited in Cai river estuary with the approximate transferable distance from the river mouth to the open sea of about 1 km. The isohaline 32%o could be defined as the separate boundary of the Cai river water; In rainy season, due to the river water discharges are high, the influence of Cai river water could be transferred to the open sea and island areas. The immerge of the Cai river water in the open sea areas in rainy season has changed the vertical structure of salinity and temperature in the northern part of Nhatrang bay. In both seasons, the Cai river water have influenced in the surface water layers 0 - 2m and the water layers deeper than 2m are influenced by the sea waters with the salinity of higher than 32%o.

Studies on the occurrence and growth rates of two intertidal fouling bryozoans in the Mattancherry channel of Cochin harbour, south-west coast of India

Occurrence and growth rates of two species of intertidal fouling bryozoans namely Electra bengalensis (Stoliczka) and Electra crustulanta (Pallas) are presented in this paper. The former was a typically marine form, settling on panels only during the high saline conditions of the pre-monsoon period and were absent during the low salinity conditions of the monsoon period, while the latter appeared to be a typical brackish water form settling on panels during the low saline conditions existing during the monsoon and post-monsoon periods and were totally absent during the pre-monsoon months. Regression co-efficient of the former was higher than that of the latter suggesting more pronounced growth in Electra bengalensis. Maximum growth for this species was noticed during March, April and May (pre-monsoon) while for the other species growth was more or less similar during monsoon and post-monsoon months (June-January) showing that the species was at home in oligohaline and mesohaline waters.

Designing of a single pack wash primer for aluminium surfaces in a marine environment

Design aspects and comparative performances of different laboratory formulations of wash primers were studied under laboratory and field conditions with reference to scratch hardness, flexibility, stability, resistance to corrosion and adhesiveness. The different formulations of single pack wash primers tested have shown superiority of the formulation prepared out of “mowital” and that it is comparable in performance to double pack wash primer.