Development and testing of the atlas ibl rod pre production boards

Il lavoro di questa tesi riguarda principalmente la progettazione, simulazione e test di laboratorio di tre versioni successive di schede VME, chiamate Read Out Driver (ROD), che sono state fabbricate per l'upgrade del 2014 dell'esperimento ATLAS Insertable B-Layer (IBL) al CERN. IBL è un nuovo layer che diverrà parte del Pixel Detector di ATLAS. Questa tesi si compone di una panoramica descrittiva dell'esperimento ATLAS in generale per poi concentrarsi sulla descrizione del layer specifico IBL. Inoltre tratta in dettaglio aspetti fisici e tecnici: specifiche di progetto, percorso realizzativo delle schede e test conseguenti. Le schede sono state dapprima prodotte in due prototipi per testare le prestazioni del sistema. Queste sono state fabbricate al fine di valutare le caratteristiche e prestazioni complessive del sistema di readout. Un secondo lotto di produzione, composto di cinque schede, è stato orientato alla correzione fine delle criticità emerse dai test del primo lotto. Un'indagine fine e approfondita del sistema ha messo a punto le schede per la fabbricazione di un terzo lotto di altre cinque schede. Attualmente la produzione è finita e complessivamente sono state realizzate 20 schede definitive che sono in fase di test. La produzione sarà validata prossimamente e le 20 schede verranno consegnate al CERN per essere inserite nel sistema di acquisizione dati del rivelatore. Al momento, il Dipartimento di Fisica ed Astronomia dell'Università di Bologna è coinvolto in un esperimento a pixel solamente attravers IBL descritto in questa tesi. In conclusione, il lavoro di tesi è stato prevalentemente focalizzato sui test delle schede e sul progetto del firmware necessario per la calibrazione e per la presa dati del rivelatore.

Measurements of ttbar Differential Cross Section at the ATLAS Experiment in pp Collisions at sqrt(s)=7TeV and sqrt(s)=8TeV

This PhD thesis presents two measurements of differential production cross section of top and anti-top pairs tt ̅ decaying in a lepton+jets final state. The normalize cross section is measured as a function of the top transverse momentum and the tt ̅ mass, transverse momentum and rapidity using the full 2011 proton-proton (pp) ATLAS data taking at a center of mass energy of √s=7 TeV and corresponding to an integrated luminosity of L=4.6 〖fb〗^(-1). The cross section is also measured at the particle level as a function of the hadronic top transverse momentum for highly energetic events using the full 2012 data taking at √s=8 TeV and with L=20 〖fb〗^(-1). The measured spectra are fully corrected for detector efficiency and resolution effects and are compared to several theoretical predictions showing a quite good agreement, depending on different spectra.

Test hardware del primo batch di schede rod per l'esperimento atlas ibl.

L’acceleratore di particelle LHC, al CERN di Ginevra, permette studi molto rilevanti nell'ambito della fisica subnucleare. L’importanza che ricopre in questo campo il rivelatore è grandissima ed è per questo che si utilizzano tecnologie d’avanguardia nella sua costruzione. É altresì fondamentale disporre di un sistema di acquisizione dati quanto più moderno ma sopratutto efficiente. Tale sistema infatti è necessario per gestire tutti i segnali elettrici che derivano dalla conversione dell’evento fisico, passaggio necessario per rendere misurabili e quantificabili le grandezze di interesse. In particolare in questa tesi viene seguito il lavoro di test delle schede ROD dell’esperimento ATLAS IBL, che mira a verificare la loro corretta funzionalità, prima che vengano spedite nei laboratori del CERN. Queste nuove schede gestiscono i segnali in arrivo dal Pixel Detector di ATLAS, per poi inviarli ai computer per la successiva elaborazione. Un sistema simile era già implementato e funzionante, ma il degrado dei chip ha causato una perdita di prestazioni, che ha reso necessario l’inserimento di un layer aggiuntivo. Il nuovo strato di rivelatori a pixel, denominato Insertable Barrel Layer (IBL), porta così un aggiornamento tecnologico e prestazionale all'interno del Pixel Detector di ATLAS, andando a ristabilire l’efficacia del sistema.

Messung der Charmonium-Produktion und Energiekalibration für Elektronen mit dem Atlas-Experiment

Der Wirkungsquerschnitt der Charmoniumproduktion wurde unter Nutzung der Daten aus pp-Kollisionen bei s^{1/2}=7TeV, die im Jahr 2010 vom Atlas-Experiment am LHC aufgezeichnet wurden, gemessen. Um das notwendige Detektorverständnis zu verbessern, wurde eine Energiekalibration durchgeführt.rnrnrnUnter Nutzung von Elektronen aus Zerfällen des Charmoniums wurde die Energieskala der elektromagnetischen Kalorimeter bei niedrigen Energien untersucht. Nach Anwendung der Kalibration wurden für die Energiemessung im Vergleich mit in Monte-Carlo-Simulationen gemessenen Energien Abweichungen von weniger als 0,5% gefunden.rnrnrnMit einer integrierten Luminosität von 2,2pb^{-1} wurde eine erste Messung des inklusiven Wirkungsquerschnittes für den Prozess pp->J/psi(e^{+}e^{-})+X bei s^{1/2}=7TeV vorgenommen. Das geschah im zugänglichen Bereich für Transversalimpulse p_{T,ee}>7GeV und Rapiditäten |y_{ee}|<2,4. Es wurden differentielle Wirkungsquerschnitte für den Transversalimpuls p_{T,ee} und für die Rapidität |y_{ee}| bestimmt. Integration beider Verteilungen lieferte für den inklusiven Wirkungsquerschnitt sigma(pp-> J/psi X)BR(J/psi->e^{+}e^{-}) die Werte (85,1+/-1,9_{stat}+/-11,2_{syst}+/-2,9_{Lum})nb und (75,4+/-1,6_{stat}+/-11,9_{syst}+/-2,6_{Lum})nb, die innerhalb der Systematik kompatibel sind.rnrnrnVergleiche mit Messungen von Atlas und CMS für den Prozess pp->J/psi(mu^{+}mu^{-})+X zeigten gute Übereinstimmung. Zum Vergleich mit der Theorie wurden Vorhersagen mit verschiedenen Modellen in nächst-zu-führender und mit Anteilen in nächst-zu-nächst-zu-führender Ordnung kombiniert. Der Vergleich zeigt eine gute Übereinstimmung bei Berücksichtigung von Anteilen in nächst-zu-nächst-zu-führender Ordnung.

Luminosity determination for the measurement of the proton-proton total cross section at 8 TeV in the Atlas experiment

La sezione d’urto totale adronica gioca un ruolo fondamentale nel programma di fisica di LHC. Un calcolo di questo parametro, fondamentale nell’ambito della teoria delle interazioni forti, non é possibile a causa dell’inapplicabilità dell’approccio perturbativo. Nonostante ciò, la sezione d’urto può essere stimata, o quanto meno le può essere dato un limite, grazie ad un certo numero di relazioni, come ad esempio il Teorema Ottico. In questo contesto, il detector ALFA (An Absolute Luminosity For ATLAS) sfrutta il Teorema Ottico per determinare la sezione d’urto totale misurando il rate di eventi elastici nella direzione forward. Un tale approccio richiede un metodo accurato di misura della luminosità in condizioni sperimentali difficoltose, caratterizzate da valori di luminosità istantanea inferiore fino a 7 ordini di grandezza rispetto alle normali condizioni di LHC. Lo scopo di questa tesi è la determinazione della luminosità integrata di due run ad alto β*, utilizzando diversi algoritmi di tipo Event-Counting dei detector BCM e LUCID. Particolare attenzione è stata riservata alla sottrazione del fondo e allo studio delle in- certezze sistematiche. I valori di luminosità integrata ottenuti sono L = 498.55 ± 0.31 (stat) ± 16.23 (sys) μb^(-1) and L = 21.93 ± 0.07 (stat) ± 0.79 (sys) μb^(-1), rispettivamente per i due run. Tali saranno forniti alla comunità di fisica che si occupa della misura delle sezioni d’urto protone-protone, elastica e totale. Nel Run II di LHC, la sezione d’urto totale protone-protone sarà stimata con un’energia nel centro di massa di 13 TeV per capire meglio la sua dipendenza dall’energia in un simile regime. Gli strumenti utilizzati e l’esperienza acquisita in questa tesi saranno fondamentali per questo scopo.

Measurement of the jet radius and transverse momentum dependence of inclusive jet suppression in lead-lead collisions at sqrtsNN=2.76 TeV with the AT detector

Measurements of inclusive jet suppression in heavy ion collisions at the LHC provide direct sensitivity to the physics of jet quenching. In a sample of lead-lead collisions at root S-NN = 2.76 TeV corresponding to an integrated luminosity of approximately 7 mu b(-1), ATLAS has measured jets with a calorimeter system over the pseudorapidity interval vertical bar eta vertical bar < 2.1 and over the transverse momentum range 38 < pT <210 GeV. Jets were reconstructed using the anti-k(t) algorithm with values for the distance parameter that determines the nominal jet radius of R = 0.2, 0.3, 0.4 and 0.5. The centrality dependence of the jet yield is characterized by the jet "central-to-peripheral ratio," R-CP. Jet production is found to be suppressed by approximately a factor of two in the 10% most central collisions relative to peripheral collisions. R-CP varies smoothly with centrality as characterized by the number of participating nucleons. The observed suppression is only weakly dependent on jet radius and transverse momentum. These results provide the first direct measurement of inclusive jet suppression in heavy ion collisions and complement previous measurements of dijet transverse energy imbalance at the LHC.

Measurements of fiducial and differential cross sections for Higgs boson production in the diphoton decay channel at √s=8 TeV with ATLAS

Measurements of fiducial and differential cross sections are presented for Higgs boson production in proton-proton collisions at a centre-of-mass energy of √s = 8TeV. The analysis is performed in the H → γγ decay channel using 20.3 fb−1 of data recorded by the ATLAS experiment at the CERN Large Hadron Collider. The signal is extracted using a fit to the diphoton invariant mass spectrum assuming that the width of the resonance is much smaller than the experimental resolution. The signal yields are corrected for the effects of detector inefficiency and resolution. The pp → H → γγ fiducial cross section is measured to be 43.2 ±9.4 (stat.) +3.2 −2.9 (syst.) ±1.2 (lumi) fb for a Higgs boson of mass 125.4 GeV decaying to two isolated photons that have transverse momentum greater than 35% and 25% of the diphoton invariant mass and each with absolute pseudorapidity less than 2.37. Four additional fiducial cross sections and two cross-section limits are presented in phase space regions that test the theoretical modelling of different Higgs boson production mechanisms, or are sensitive to physics beyond the Standard Model. Differential cross sections are also presented, as a function of variables related to the diphoton kinematics and the jet activity produced in the Higgs boson events. The observed spectra are statistically limited but broadly in line with the theoretical expectations.

Test vector generation for the phase II ATLAS event filter trigger upgrade

In the near future, the LHC experiments will continue to be upgraded as the LHC luminosity will increase from the design 1034 to 7.5 × 1034, with the HL-LHC project, to reach 3000 × f b−1 of accumulated statistics. After the end of a period of data collection, CERN will face a long shutdown to improve overall performance by upgrading the experiments and implementing more advanced technologies and infrastructures. In particular, ATLAS will upgrade parts of the detector, the trigger, and the data acquisition system. It will also implement new strategies and algorithms for processing and transferring the data to the final storage. This PhD thesis presents a study of a new pattern recognition algorithm to be used in the trigger system, which is a software designed to provide the information necessary to select physical events from background data. The idea is to use the well-known Hough Transform mathematical formula as an algorithm for detecting particle trajectories. The effectiveness of the algorithm has already been validated in the past, independently of particle physics applications, to detect generic shapes in images. Here, a software emulation tool is proposed for the hardware implementation of the Hough Transform, to reconstruct the tracks in the ATLAS Trigger and Data Acquisition system. Until now, it has never been implemented on electronics in particle physics experiments, and as a hardware implementation it would provide overall latency benefits. A comparison between the simulated data and the physical system was performed on a Xilinx UltraScale+ FPGA device.

Determinação rápida de fármacos básicos em plasma por cromatografia a gás com detector de nitrogênio e fósforo

A simple and fast method for determination of 40 basic drugs in human plasma employing gas-chromatography with nitrogen-phosphorus detection was developed and validated. Drugs were extracted from 800 µL of plasma with 250 µL of butyl acetate at basic pH. Aliquots of the organic extract were directly injected on a column with methylsilicone stationary phase. Total chromatographic run time was 25 min. All compounds were detected in concentrations ranging from therapeutic to toxic levels, with intermediate precision CV% below 11.2 and accuracy in the range of 92-114%.

Determination of paracetamol at a graphite-polyurethane composite electrode as an amperometric flow detector

A bare graphite-polyurethane composite was evaluated as an amperometric flow injection detector in the determination of paracetamol (APAP) in pharmaceutical formulations. A linear analytical curve was observed in the 5.00 x 10-5 to 5.00 x 10-3 mol L-1 range with a minimum detectable net concentration of 18.9 µmol L-1 and 180 determinations h-1, after optimization of parameters such as the detection potential, sample loop volume, and carrier solution flow rate. Interference of ascorbic acid was observed, however, it was possible overcome the interference, reaching results that agreed with HPLC within 95% confidence level. These results showed that the graphite-polyurethane composite can be used as an amperometric detector for flow analysis in the determination of APAP.

Acidentes de trânsito no Brasil: um atlas de sua distribuição

O Atlas foi concebido para colocar à disposição do usuário os dados disponíveis sobre acidentes de trânsito no Brasil, já trabalhados sob forma de indicadores e apresentados predominantemente como mapas, gráficos, quadros e tabelas. Neste artigo, são apresentados os principais resultados obtidos, bem como, algumas conclusões, considerações, ponderações e possíveis explicações quanto aos problemas e questões relacionadas a este importante agravo à saúde

Measurement of the underground atmospheric muon charge ratio using the MINOS Near Detector

The magnetized MINOS Near Detector, at a depth of 225 mwe, is used to measure the atmospheric muon charge ratio. The ratio of observed positive to negative atmospheric muon rates, using 301 days of data, is measured to be 1.266 +/- 0.001(stat)(-0.014)(+0.015)(syst). This measurement is consistent with previous results from other shallow underground detectors and is 0.108 +/- 0.019(stat + syst) lower than the measurement at the functionally identical MINOS Far Detector at a depth of 2070 mwe. This increase in charge ratio as a function of depth is consistent with an increase in the fraction of muons arising from kaon decay for increasing muon surface energies.

Search for Lorentz Invariance and CPT Violation with the MINOS Far Detector

We searched for a sidereal modulation in the MINOS far detector neutrino rate. Such a signal would be a consequence of Lorentz and CPT violation as described by the standard-model extension framework. It also would be the first detection of a perturbative effect to conventional neutrino mass oscillations. We found no evidence for this sidereal signature, and the upper limits placed on the magnitudes of the Lorentz and CPT violating coefficients describing the theory are an improvement by factors of 20-510 over the current best limits found by using the MINOS near detector.

Neutrino and antineutrino inclusive charged-current cross section measurements with the MINOS near detector

The energy dependence of the neutrino-iron and antineutrino-iron inclusive charged-current cross sections and their ratio have been measured using a high-statistics sample with the MINOS near detector exposed to the NuMI beam from the main injector at Fermilab. Neutrino and antineutrino fluxes were determined using a low hadronic energy subsample of charged-current events. We report measurements of nu-Fe ((nu) over bar - Fe) cross section in the energy range 3-50 GeV (5-50 GeV) with precision of 2%-8% (3%-9%) and their ratio which is measured with precision 2%-8%. The data set spans the region from low energy, where accurate measurements are sparse, up to the high-energy scaling region where the cross section is well understood.