In-situ synthesis of AlN powders and composite AlN powders with yttrium addition

Using Al-Mg and Al-Mg-Y alloys as raw materials and nitrogen as gas reactants, AIN powders and composite AIN powders by in-situ synthesis method were prepared. AIN lumps prepared by the nitriding of Al-Mg and Al-Mg-Y alloys have porous microstructure, which is favorable for pulverization. They have high purity, containing 1.23 % (mass fraction) oxygen impurity, and consisted of AIN single phase . The average particle size of AIN powders is 6.78 mum. Composite AlN powders consist of AlN phases and rare, earth oxide Y2O3 phase. The distribution of particle size of AIN powders shows two peaks. In view, of packing factor, AIN powders with such size distribution can easily be sintered to high density.

富钇稀土-铝合金制取的研究Study on Preparation of Yttrium-Rich RE-Al Alloys

我国江西龙南稀土矿是目前世界上储量最大的富钇稀土矿、研制具有多种用途的钇（Y）-铝（Al）或富钇混合稀土（Ymm）-铝中间合金，对于开拓我国龙南稀土矿的应用领域扩大稀土合金出口具有重要意义。基于这一背景并针对目前氟化物体系制取Ymm-Al合金时存在着电解温度高，腐蚀现象严重，电效偏低等缺点，本文系统开展了在氯化物熔盐体系中电解制取Ymm-Al合金的研究工作。本工作由三部分组成：在第一部分工作中，开展了熔盐电解所需要基本原料-无水稀土氯化物制取的工艺研究。利用化学分析和结构分析手段，弄清了干法氯化过程中YmmCl_3水解的机理，提出了减弱水解的措施，即YmmCl_3先在850-900 ℃灼烧1.5 + 0.2hr，脱掉吸附水并将碱式碳酸盐转化为氧化物，增加稀土氧化物的比表面。通过条件试验得到最佳工艺条件为：采用NH_4 Cl:Ymm_2 O_3 = 14:1（摩尔比）的配料比，每次投入氯化装置的原料量为0.26 - 0.36 kg, 在400-450 ℃氯化反应激烈开始后迅速降温至400 ℃以下，待物料粘结现象消失后，再行升温氯化。出料及后期控制温在475 ± 25 ℃。经过3.8 ± 0.2hr氯化，可制得水不溶物小于1%并符合熔盐电解要求的YmmCl_3原料。此新工艺与原有干法工艺相比，流程短，装置简单，不需密闭抽真空，成本低，适于制取任何量的优质熔盐电解所需氯化稀土原料。在第二部分工作中，利用上述YmmCl_3原料，以液态铝为阴极，在氯化物体系中进行熔盐电解，通过试验得出在小型试验规模制取Ymm-Al合金的最隹工艺条件为：电解质组成（重量比）40%YmmCl_3-1%NaF-59%等摩尔的NaCl-KCl；电解温度为790 ± 5 ℃；阴极电流密为0.7 - 0.02A/cm~2；电解电量为333 ± 5库仑/克铝，制得钇铝合金中Ymm含量为10 ± 2%。添加1%的NaF可消除阴极表面生成枝状物，减少合金中夹渣和熔盐中沉渣。在电解工作中，将方差分析应用于试验数据处理，方差分析结果表明，各种试验因素对电效有明显影响，试验数据可靠，试验误差在允许范围以内。在第三部分工作中，利用线性扫描伏安法测定了在最隹电解工艺条件下Y~（3+）和Ymm在液态铝及钼电极上的析出电位。测定结果表明：Y~（3+）和Ymm~（3+）在液态铝阴极上的析出电位比在钼阴极上偏正0.2 ～ 0.8伏，氟离子的加入要比不加氟时析出电位不有同程度的负移，但考虑到氟离了具有消渣作用，加入少量氟比物添加剂对提高电效有利。

Combustion synthesis and luminescent properties of the Eu3+-doped yttrium oxysulfide nanocrystalline

Nanocrystallinc Y2O2S:Eu3+ was successfully prepared with a combustion synthesis method, the corresponding bulk Y2O2S:Eu3+ was synthesized by conventional sulfur flux method. The results of XRD indicated that both bulk and nanocrystalline Y2O2S:Eu3+ have Pure hexagonal phases. The crystallite size was calculated to be about 20 nm according to Scherrer formula, which was consistent with the size as indicated by transmission electron microscopy (TEM).

The solid-liquid extraction of yttrium from rare earths by solvent (ionic liquid) impreganated resin coupled with complexing method

A kind of solvent (ionic liquid) impreganated resin (IL-SIR) was developed herein for ameliorating imidazolium-type IL-based liquid-liquid extraction of metal ions. In this study, [C(8)mim][PF6] containing Cyanex923 was immobilized on XAD-7 resin for solid-liquid extraction of rare earth (RE). The solid-liquid extraction contributed to ameliorating mass transfer efficiency, i.e. shortening equilibrium time from 40 min to 20 min, increasing extraction efficiency from 29% to 80%. In additional, the novel IL-SIR could separate Y(III) from Sc(III), Ho(III), Er(III), Yb(III) effectively by adding water-soluble complexing agent.

Silica Materials Doped with Bifunctional Ionic Liquid Extractant for Yttrium Extraction

Two new silica-based organic-inorganic hybrid materials (B104SGs and O104SGs) doped with a binary mixture of imidazolium and phosphonium ionic liquids have been synthesized and used as sorbents in batch system for rare earths (RE) separation. Imidazolium ionic liquids 1-butyl-3-methylimidazolium hexafluorophosphate (C(4)mim(+)PF(6)(-)) or 1-octyl-3-methylimidazolium hexafluorophosphate (C(8)mim(+)PF(6)(-)) acted as porogens to prepare porous materials and additives to stabilize extractant within silica gel.

Electrolytic Deposition and Diffusion of Lithium onto Magnesium-9 Wt Pct Yttrium Bulk Alloy in Low-Temperature Molten Salt of Lithium Chloride and Potassium Chloride

The electrolytic deposition and diffusion of lithium onto bulk magnesium-9 wt pct yttrium alloy cathode in molten salt of 47 wt pct lithium chloride and 53 wt pct potassium chloride at 693 K were investigated. Results show that magnesium-yttrium-lithium ternary alloys are formed on the surface of the cathodes, and a penetration depth of 642 mu m is acquired after 2 hours of electrolysis at the cathodic current density of 0.06 A center dot cm(-2). The diffusion of lithium results in a great amount of precipitates in the lithium containing layer. These precipitates are the compound of Mg41Y5, which arrange along the grain boundaries and hinder the diffusion of lithium, and solid solution of yttrium in magnesium. The grain boundaries and the twins of the magnesium-9 wt pct yttrium substrate also have negative effects on the diffusion of lithium.

Effect of yttrium-rich misch metal on the microstructures, mechanical properties and corrosion behavior of die cast AZ91 alloy

Die cast AZ91-xYmm (x = 0-0.8 wt.%) magnesium alloys with excellent tensile properties and corrosion resistance behavior were successfully prepared by a simple addition of yttrium-rich misch metal (Ymm) to AZ91. Influences of Ymm on the microstructure, mechanical properties and corrosion behavior of AZ91 were investigated. The results showed that addition of Ymm to die cast AZ91 alloy could re. ne the microstructure including primary alpha-Mg and eutectic beta-Mg17Al12. When the content of Ymm reached 0.8 wt.% a small quantity of Al2Y phase would form. The tensile properties were improved greatly with addition of Ymm to AZ91. The creep rate of the AZ91-Ymm alloys, tested at 150 degrees C/50MPa, was one order of magnitude lower than that of AZ91. When addition of Ymm was more than 0.3 wt.%, the salt-spray corrosion resistance of AZ91-Ymm alloys could be 30-40 times of that of AZ91. The improvement of corrosion resistance with addition of Ymm was confirmed by the results of electrochemical polarization experiments. Mechanism of the improvement of mechanical properties and corrosion behavior caused by Ymm was also discussed.

The preparation of sol-gel materials doped with ionic liquids and trialkyl phosphine oxides for Yttrium(III) uptake

A new material (IL923SGs) composed of ionic liquids and trialkyl phosphine oxides (Cyanex 923) for Y(III) uptake was prepared via a sol-gel method. The hydrophobic ionic liquid 1-octyl-3-methylimidazolium hexafluorophosphate (C(8)mim(+)PF(6)-) was used as solvent medium and pore templating material. The extraction of Y(III) by IL923SGs was mainly due to the complexation of metal ions with Cyanex 923 doped in the solid silica. Ionic liquid was stably doped into the silica gel matrix providing a diffusion medium for Cyanex 923, and this will result in higher removal efficiencies and excellent stability for metal ions separation. IL923SGs were also easily regenerated and reused in the subsequent removal of Y(III) in four cycles.

Mixed ligands supported yttrium alkyl complexes: Synthesis, characterization and catalysis toward lactide polymerization

Treatment of yttrium tris(alkyl)s, Y(CH2SiMe3)(3)(THF)(2), by equimolar H(C5Me4)SiMe3(HCp') and indene (Ind-H) afforded (eta(5)-Cp')Y(CH2SiMe3)(2)(THF) (1) and (eta(5)-Ind)Y(CH2SiMe3)(2)(THF) (2) via alkane elimination, respectively. Complex 1 reacted with methoxyamino phenols, 4,6-(CH3)(2)-2-[(MeOCH2CH2)(2)-NCH2]-C6H2-OH (HL1) and 4,6-(CMe3)(2)-2-[(MeOCH2CH2)(2)-NCH2]-C6H2OH (HL2) gave mixed ligands supported alkyl complexes [(eta(5)-Cp')(L)]Y(CH2SiMe3) (3: L = L-1; 4: L = L-2). Whilst, complex 2 was treated with HL2 to yield [(eta(5)-Ind)(L-2)]Y(CH2SiMe3) (5). The molecular structures of 3 and 5 were confirmed by X-ray diffraction to be mono(alkyl)s of THF-free, adopting pyramidal and tetragonal-bipyramidal geometry, respectively. Complexes 3 and 5 were high active initiators for the ring-opening polymerization Of L-lactide to give isotactic polylactide with high molecular weight and narrow to moderate polydispersity.