Comparative efficiency of trawls made of nylon, polyethylene monofilament and tape twines

Results of comparative fishing operations conducted with three nets of identical design made of nylon, twisted polyethylene monofilament and high density polyethylene (HDPE) tape twines are presented in this communication. Since the tape net recorded the highest prawn and fish catch, monofilament and nylon following in order, it can be recommended to the fishing industry as one of the cheapest and effective fishing materials evolved for trawl fabrication.

Tensile strength properties of polyethylene netting twines under exposure to out-door and artificial UV radiation

Photodegradation of three types of polyethylene twines namely, polyethylene fibrillated tape twine, polyethylene flat tape twine and polyethylene monofilament twines were studied by exposing them to sunlight and artificial UV radiation. The percentage residual strength varied in the samples, the monofilament with the highest residual strength followed by fibrillated tape twine and flat tape twine. A plot of the difference between the breaking strengths of the fibrillated tape twine and the mono filament twines against any given period of exposure exhibited a linear relationship

Comparing the hairiness of solospun and ring spun worsted yarns

This paper compares the hairiness of Solospun yarns with conventional ring spun worsted yams of the same specifications. A 24-spindles worsted ring spinning frame is used to spin the Solospun and conventional ring spun yarns at the same time, and yarn hairiness is measured. The total hairiness number (Tp), the number of hairs longer than or equal to 3mm (S3), the percentage of longer hairs in total hairs (100S3/Tp), and the total hair length per unit yarn length (K' ) are used to compare the hairiness of these yams. The results indicate that the Solospun yarn exhibits less hairiness in each of the hair length groups and has lower variations in yarn hairiness. The hair-length distribution of the Solospun yarn follows an exponential law just like conventional ring spun yams. There is a statistically significant difference between the Solospun and conventional ring spun yams for T p, S3, and K', but the difference in 1 00S 3/Tp is not statistically significant for these yams. In addition, the Tp, S3, and K' values of the Solospun yarn decrease with twist increase and increase with spindle speed increase, but the 100S3/Tp values of the Solospun and conventional ring spun yarns in this study behave differently in that they are affected by twist level and spindle speed.

Effects of bleaching and dyeing on the quality of alpaca tops and yarns

This paper reports the effects of bleaching of alpaca tops and dyeing of bleached alpaca tops/yarns on the quality of tops and yarns. A dark brown alpaca top was bleached with hydrogen peroxide. Two bleaching methods were tried for effectiveness of color removal. A portion of each bleached top was dyed after bleaching. Color parameters were examined for unbleached, bleached and bleached/dyed tops, these tops were then converted into yarns of different twist levels and counts using a worsted spinning system. Some of the bleached yarn from each bleaching method was dyed in a package dye vat to compare the difference of top dyeing versus yarn package dyeing on yarn quality. Fiber diameter, yarn strength, yarn evenness, yarn hairiness and fiber degradation were tested to examine the effects of bleaching and dyeing on these properties at top and yarn stages. A processing route for bleaching and dyeing alpaca fiber was recommended.

Conducting nylon, cotton and wool yarns by continuous vapor polymerization of pyrrole

Conductive textile yarns were prepared by a continuous vapor polymerization method; the application of polypyrrole by the continuous vapor polymerization method used is designed for the easy adaptation into industrial procedures. The resultant conductive yarns were examined by longitudinal and cross-sectional views, clearly showing the varying levels of penetration of the polymer into the yarn structure. It was found that for wool the optimum specific resistance was achieved by using the 400 TPM yarn with a FeCl3 solution concentration of 80 g/L FeCl3 to produce 1.69 Ω g/cm2. For cotton yarn, the optimum specific resistance of 1.53 Ω g/cm2 was obtained with 80 g/L of a FeCl3 solution.

The dimensional and mechanical properties of wool/polyester fabrics made from vortex and ring-spun yarns

Fabric woven from wool/polyester (PES) Murata vortex spun (MVS) blend yarn is a commercially viable proposition particularly on the basis of advantageous wear-resistant properties, compared with fabric made from traditional worsted ring-spun yarn. However, in some early industrial trials with fabric made from 45/55-blend wool/PES MVS yarn, significantly greater relaxation shrinkage was found relative to comparable worsted ring-spun fabric. It was noted at the time that the amount of relaxation shrinkage in MVS fabric could be reduced to a large extent by using steamed MVS yarn.

In this study, the extent of variations in the dimensional and mechanical properties of fabric samples woven from a combination of steamed and unsteamed MVS yarn and equivalent worsted ring-spun yarn is examined. In general, greater hygral expansion and relaxation shrinkage were found in loom-state fabrics made from unsteamed MVS yarns, whereas the fabric made from steamed MVS and ring-spun yarns gave relatively low levels of relaxation shrinkage and hygral expansion. Permanent setting of fabrics, by pressure steaming, was found to be more effective than yarn pre-steaming in reducing relaxation shrinkage levels of fabrics made from unsteamed MVS yarn. After pressure steaming, all fabrics showed similar levels of relaxation shrinkage and hygral expansion.

Permanent setting of the fabrics, by pressure steaming, resulted in similar levels of relaxation shrinkage and hygral expansion, irrespective of the yarn production method; relaxation shrinkage fell to around 1% and hygral expansion increased by about 1%, relative to the loom-state samples. MVS fabrics were relatively heavier and fuller and had a firmer handle than the worsted ring-spun fabrics, reflecting the greater fabric weight, thickness and shear rigidity measured on these fabrics. These attributes are associated with different structures of the worsted ring-spun and MVS yarns used to make the fabrics.

Recent developments in electrospinning of nanofibers and nanofiber yarns

Electropsipinning is a simple, but efficient and versatile, technology to produce polymeric nanofibers for diverse applications in both textile and non-textile areas. In this paper, recent research developments in electrospinning and electrospun nanofibers, especially thaose from the Centre for Material and Fiber Innovation, Deakin University, are introduced. Important findings on needleless mass-electrospinning and direct electrospinning of highly-twisted continuous manfiber yarns are presented.

Needleless electrospinning and direct electrospinning of nanofiber yarns

Electrospinning is a simple, but efficient and versatile, technology to produce polymeric nanofibers for widely diverse applications in both textile and non-textile areas [1]. This technique has been shown many advantages such as universality in processing polymeric materials, eases of controlling the fiber diameter and functionalizing nanofibers through adjusting solution composition for electrospinning, and flexibility to generate fibrous membranes of various geometries. Although the novel applications of electrospun nanofibers have been extensively explored [2], the technology development for mass electrospinning of nanofibers has been hampered.

Electrospinning of continuous nanofiber bundles and twisted nanofiber yarns

Spinning is a prehistoric technology in which endless filaments, shorter fibers or twisted fibers are put together to produce yarns that serve as key element to assemble multifarious structural designs for diverse functions. Electrospinning has been regarded as the most effective and versatile technology to produce nanofibers with controlled fiber morphology, dimension and functional components from various polymeric materials (Dersch et al., 2007, Frenot and Chronakis, 2003, Schreuder-Gibson et al., 2002). However, most electrospun fibers are produced in the form of randomly-oriented nonwoven fiber mats (Doshi and Reneker, 1995, Madhavamoorthi, 2005). The relatively low mechanical strength and difficulty in tailoring the fibrous structure have restricted their applications. With the rapid development in nanoscience and nanotechnology, yarns composed of nanofibers may uncover new opportunities for development of well-defined three dimensional nano fibrous architectures. This chapter focuses on recent research and advancement in electrospinning of nanofiber bundles and nanofiber yarns. The preparation, morphology, mechanical properties and potential applications of these fibrous materials are discussed in details.