A one-step technique to prepare aligned arrays of carbon nanotubes

A simple effective pyrolysis technique has been developed to synthesize aligned arrays of multi-walled carbon nanotubes (MWCNTs) without using any carrier gas in a single-stage furnace at 700 °C. This technique eliminates nearly the entire complex and expensive machinery associated with other extensively used methods for preparation of CNTs such as chemical vapour deposition (CVD) and pyrolysis. Carbon source materials such as xylene, cyclohexane, camphor, hexane, toluene, pyridine and benzene have been pyrolyzed separately with the catalyst source material ferrocene to obtain aligned arrays of MWCNTs. The synthesized CNTs have been characterized by scanning electron microscopy (SEM), x-ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA) and Raman spectroscopy. In this technique, the need for the tedious and time-consuming preparation of metal catalysts and continuously fed carbon source material containing carrier gas can be avoided. This method is a single-step process where not many parameters are required to be monitored in order to prepare aligned MWCNTs. For the production of CNTs, the technique has great advantages such as low cost and easy operation.

Surface tension of some binary organic solutions of alkylbenzenes and 1-alkanols

The surface tensions of binary mixtures of 1-alkanols (Cl-Cd with benzene, toluene, or xylene were measured. The results were correlated with the activity coefficients calculated through the group contribution method such as UNIFAC, with the maximum deviation from the experimental results less that 5%. The coefficients of the correlation are correlated with the chain length.

Dye sensitized solar cell based on platinum decorated multiwall carbon nanotubes as catalytic layer on the counter electrode

In this study we have employed multiwall carbon nanotubes (MWCNT), decorated with platinum as catalytic layer for the reduction of tri-iodide ions in dye sensitized solar cell (DSSC). MWCNTs have been prepared by a simple one step pyrolysis method using ferrocene as the catalyst and xylene as the carbon source. Platinum decorated MWCNTs have been prepared by chemical reduction method. The as prepared MWCNTs and Pt/MWCNTs have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). In combination with a dye adsorbed TiO(2) photoanode and an organic liquid electrolyte, Pt/MWCNT composite showed an enhanced short circuit current density of 16.12 mA/cm(2) leading to a cell efficiency of 6.50% which is comparable to that of Platinum. (C) 2011 Elsevier Ltd. All rights reserved.

Alkylation of toluene by methanol over alkali exchanged zeolite-X: side chain versus ring alkylation

The ring versus side-chain alkylation of toluene with methanol over alkali-exchanged zeolite-X of differing basicity has been investigated by in situ infrared spectroscopy and TPD measurements. Over the basic Cs-exchanged zeolite the product of alkylation is styrene/ethylbenzene while over the acidic Li-exchanged zeolite ring alkylation occurs to give mainly xylene as the product. FTIR and TPD investigations reveal that, the key difference in the two types of alkylation processes lies in the state of the adsorbed methanol present at higher temperatures in the zeolite. In basic zeolites, methanol decomposes to formaldehyde and formates. The former is the key ‘side-chain’ alkylating species that leads to the formation of styrene. In the acidic zeolites it is shown that methanol bound to the acid sites plays an active role in the ‘ring alkylation’ of toluene to xylene.

Esterification of stearic acid with p-cresol over modified Indian bentonite clay catalysts

The esterification of stearic acid with p-cresol using modified Indian bentonite clay catalysts has been reported. The reaction was studied over exchanged clays, acid activated clays, exchanged acid activated clays, aluminium pillared clay, aluminium pillared acid activated clay, molecular sieve Al-MCM-41, zeolite H beta, ZrO2, S-ZrO2, p-TSA, montmorillonite K10, and montmorillonite KSF in o-xylene for 6 h. The catalysts were characterized by X-ray diffraction and surface area measurements. The acidity was determined by n-butylamine back-titration method and DRIFTS after pyridine adsorption. Acid activated Indian bentonite (AAIB) was found to be a better catalyst compared to other catalysts in the esterification of stearic acid with p-cresol.

Kinetically stabilized C-60-toluene solvate nanostructures with a discrete absorption edge enabling supramolecular topotactic molecular exchange

Nanosized fullerene solvates have attracted widespread research attention due to recent interesting discoveries. A particular type of solvate is limited to a fixed number of solvents and designing new solvates within the same family is a fundamental challenge. Here we demonstrate that the hexagonal closed packed (HCP) phase of C-60 solvates, formed with m-xylene, can also be stabilized using toluene. Contrary to the notion on their instability, these can be stabilized from minutes up to months by tuning the occupancy of solvent molecules. Due to high stability, we could record their absorption edge, and measure excitonic life-time, which has not been reported for any C-60 solvate. Despite being solid, absorbance spectrum of the solvates is similar in appearance to that of C-60 in solution. A new absorption band appears at 673 nm. The fluorescence lifetime at 760 nm is similar to 1.2 ns, suggesting an excited state unaffected by solvent-C-60 interaction. Finally, we utilized the unstable set of HCP solvates to exchange with a second solvent by a topotactic exchange mechanism, which rendered near permanent stability to the otherwise few minutes stable solvates. This is also the first example of topotactic exchange in supramolecular crystal, which is widely known in ionic solids. (C) 2014 Elsevier Ltd. All rights reserved.

Binding of carboxylatopillar5]arene with alkyl and aryl ammonium salts in aqueous medium

The complex formation of alkyl ammonium salts by water-soluble carboxylatopillar5] arene (CP5A) in aqueous medium is reported. p-Xylene diammonium salt and a series of secondary alkyl ammonium salts with various alkyl groups have been prepared and investigated for complex formation. All the ammonium salts exhibit strong host-guest complexation with CP5A under neutral aqueous conditions. H-1 NMR, H-1 DOSY and 2D NOESY NMR experiments have been performed to characterize these inclusion complexes. In this study, the hydrophobic and electrostatic interactions govern the complex formation leading to the formation of pseudorotaxane species. Five pseudo2] rotaxanes and one pseudo3] rotaxane were obtained whose association constant values and stoichiometry were evaluated by an NMR titration method. The results indicate the use of ammonium salts as new complimentary synthons for CP5A in aqueous medium, adding to the repertoire of existing recognition motifs such as paraquat and 1,4-bis(pyridinium) derivatives.

Pyrolysis of 3-carene: Experiment, Theory and Modeling

Thermal decomposition studies of 3-carene, a bio-fuel, have been carried out behind the reflected shock wave in a single pulse shock tube for temperature ranging from 920 K to 1220 K. The observed products in thermal decomposition of 3-carene are acetylene, allene, butadiene, isoprene, cyclopentadiene, hexatriene, benzene, toluene and p-xylene. The overall rate constant for 3-carene decomposition was found to be k/s(-1) = 10((9.95 +/- 0.54)) exp(-40.88 +/- 2.71 kcal mol(-1) /RT). Ab-initio theoretical calculations were carried out to find the minimum energy pathway that could explain the formation of the observed products in the thermal decomposition experiments. These calculations were carried out at B3LYP/6-311 + G(d,p) and G3 level of theories. A kinetic mechanism explaining the observed products in the thermal decomposition experiments has been derived. It is concluded that the linear hydrocarbons are the primary products in the pyrolysis of 3-carene.

Investigations of secondary organic aerosol formation in laboratory chambers

Secondary organic aerosol (SOA) is produced in the atmosphere by oxidation of volatile organic compounds. Laboratory chambers are used understand the formation mechanisms and evolution of SOA formed under controlled conditions. This thesis presents studies of SOA formed from anthropogenic and biogenic precursors and discusses the effects of chamber walls on suspended vapors and particles.

During a chamber experiment, suspended vapors and particles can interact with the chamber walls. Particle wall loss is relatively well-understood, but vapor wall losses have received little study. Vapor wall loss of 2,3-epoxy-1,4-butanediol (BEPOX) and glyoxal was identified, quantified, and found to depend on chamber age and relative humidity.

Particles reside in the atmosphere for a week or more and can evolve chemically during that time period, a process termed aging. Simulating aging in laboratory chambers has proven to be challenging. A protocol was developed to extend the duration of a chamber experiment to 36 h of oxidation and was used to evaluate aging of SOA produced from m-xylene. Total SOA mass concentration increased and then decreased with increasing photooxidation suggesting a transition from functionalization to fragmentation chemistry driven by photochemical processes. SOA oxidation, measured as the bulk particle elemental oxygen-to-carbon ratio and fraction of organic mass at m/z 44, increased continuously starting after 5 h of photooxidation.

The physical state and chemical composition of an organic aerosol affect the mixing of aerosol components and its interactions with condensing species. A laboratory chamber protocol was developed to evaluate the mixing of SOA produced sequentially from two different sources by heating the chamber to induce particle evaporation. Using this protocol, SOA produced from toluene was found to be less volatile than that produced from a-pinene. When the two types of SOA were formed sequentially, the evaporation behavior most closely represented that of SOA from the second parent hydrocarbon, suggesting that the structure of the mixed SOA particles resembles a core of SOA from the first precursor coated by a layer of SOA from the second precursor, indicative of limiting mixing.

溶胶-凝胶光波导环形谐振腔的挥发性有机化合物传感特性

采用溶胶-凝胶法制作波导环形谐振腔, 讨论了环形谐振腔器件的传输特性。测量了在不同物质、不同体积分数的挥发性有机化合物(VOC)蒸气气氛下器件的传输光谱的敏感性。结果表明, 谐振波长随甲醇、乙醇、丙醇等醇类化合物, 以及丙酮、甲醛等蒸气体积分数的上升而向长波方向移动, 具有高的灵敏度, 且两者基本呈线性关系。其中, 对丙醇最敏感, 灵敏度达到1.403 pm/10-6。对甲烷和二甲苯也有微弱反应, 但是其灵敏度很低。也测量了水蒸气对传输谱特性的影响。观察到传输谱衬比度对不同挥发性有机化合物物质蒸气的不同敏

Determinação de compostos monoaromáticos voláteis provenientes de emissões de veículos leves, em estacionamentos subterrâneos.

Este trabalho visa determinar a contribuição das emissões evaporativas provenientes dos veículos leves de passageiro, para a degradação da qualidade do ar atmosférico. O objetivo principal é avaliar as concentrações compostos monoaromáticos voláteis Benzeno, Tolueno, Etilbenzeno e Xilenos (BTEX) em ambientes confinados, sendo este realizado em um local que caracterize a realidade da frota veicular da Região metropolitana do Rio de Janeiro. As amostras foram coletadas em um estacionamento subterrâneo de um Shopping Center da zona norte do Rio de Janeiro, através do sistema de amostragem ativa, utilizando cartucho de carvão ativo como adsorvente. As amostras foram extraídas com solvente orgânico e analisadas posteriormente por Cromatografia gasosa acoplada à espectrometria de massas (CGEM). As médias dos resultados obtidos foram 52,7 g.m-3 para o benzeno, 203,6 g.m-3 para o tolueno, 44,6 g.m-3 para o etilbenzeno, 115,7 g.m-3 para os xilenos, sendo o tolueno o composto encontrado em maior abundância. Esses resultados foram comparados com resultados encontrados na literatura de emissões veiculares em ambientes confinados como garagens e túneis. Foi investigada a correlação com as emissões do veículo em movimento, obtidas através de estudos previamente realizados em um túnel de grande circulação e as emissões obtidas no estacionamento subterrâneo. Através desses dados ficou demonstrada diferença das fontes de emissão.

Effects of natural gas pipeline condensate and crude oil spills, and comments on remediation, with emphasis on south Louisiana salt marshes: a review

This report reviews some of the natural ecological processes at work within a salt marsh as they relate to a spill of natural gas condensate - a mixture of aliphatic hydrocarbons, n-hexane, benzene, toluene, and xylene. It also reviews the environmental impacts of some of the components of natural gas condensate as well as related compounds (crude oil, higher molecular weight hydrocarbons, polycyclic aromatic hydrocarons - PAHs, linear alkyl-benzenes - LABs, etc.) on salt marsh ecosystems in southern Louisiana and elsewhere in the world. The behavior and persistence of these compounds once they have entered the environment is also considered.

Hermetically-coated superparamagnetic Fe2O3 particles with SiO2 nanofilms

Magnetic nanoparticles are frequently coated with SiO2to improve their functionality and bio-compatibility in a range of biomedical and polymer nanocomposile applications. In this paper, a scalable flame aerosol technology is used to produce highly dispersible, superparamagnetic iron oxide nanoparticles hermetically coaled with silica to retain full magnetization performance. Iron oxide particles were produced by flame spray pyrolysis (FSP) of iron acelylacetonale in xylene/acetonitrile solutions, and the resulting aerosol was in situ coaled with SiO2 by oxidation of swirling hexamethlydisiloxane vapor. The process allows independent control of the core Fe2O3, particle properties and the thickness of their silica coaling film. This ensures that the non-magnetic SiO2 layer can be closely controlled and minimized. The optimal SiO2 content for complete (hermetic) encapsulation of the magnetic core particles was determined by isopropanol chemisorption. The magnetization of Fe2O3 coated with about 2 nm thin SiO2 layers was nearly identical lo that of uncoated, pure Fe2O3 nanoparlicles.

Hermetically coated superparamagnetic Fe2O3 particles with SiO2 nanofilms

Magnetic nanoparticles are frequently coated with SiO2 to improve their functionality and biocom-patibility in a range of biomedical and polymer nanocomposite applications. In this paper, a scalable flame aerosol technology is used to produce highly dispersible, superparamagnetic iron oxide nanoparticles hermetically coated with silica to retain full magnetization performance. Iron oxide particles were produced by flame spray pyrolysis of iron acetylacetonate in xylene/acetonitrile solutions and the resulting aerosol was in situ coated with silicon dioxide by oxidation of swirling hexamethlydisiloxane vapor. The process allows independent control of the core Fe2O3 (maghemite) particle properties and the thickness of their silica coating film. This ensures that the nonmagnetic SiO2 layer can be closely controlled and minimized. The optimal SiO2 content for complete (hermetic) encapsulation of the magnetic core particles was determined by isopropanol chemisorption. The magnetization of Fe 2O3 coated with about 2 nm thin SiO2 layers was nearly identical to that of uncoated, pure Fe2O3 nanoparticles. © 2009 American Chemical Society.