Influence of Measured Characteristics on Price Received for Merino Wool from the Traprock Area of Southern Queensland

In this study of a commercial wool clip sold in the years 1991/92-1996/97, the effect of wool characteristics, (staple length, staple strength, fibre diameter, position of break, vegetable matter, hauteur, yield and coefficient of variation of staple length) on price was explored together with their effect on the ratio of price received per lot to the average weekly price (1994/95 basis) for clean wool of the same fibre diameter. Fibre diameter and where the point of break occurred had the most effect on price. As hauteur, staple length and yield increased, so did the price ratio but it decreased as the percentage of vegetable matter and the coefficient of variation of the staple length increased. The ratio of proceeds if all wool had been sold at average weekly market price, to proceeds if all wool had been 21µm or less, indicated little financial advantage over the six-year period as most sale lots were under 22µm. To raise the proceeds of sale above the proceeds estimated using average market price for each lot, the analyses suggested that hauteur, staple length and its coefficient of variation, could be considered, in addition to fibre diameter, when sourcing wethers for purchase. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000, Sydney, Australia.

Genetic Parameters for Staple Length and Staple Strength of Merino Wool Produced in Central and North West Queensland

Estimates of genetic parameters are presented for staple length and staple strength for 15 month old, medium Peppin sheep at Longreach and Julia Creek Queensland. The effects of birth type, sex and year of birth are shown. There were significant interactions for sex by site and for sex by year of birth. Heritability of staple length and strength were respectively 0.75 and 0.37 for the Longreach flock and 0.70 and 0.23 for the Julia Creek flock. The heritability of staple strength agrees with other published data however the estimate for staple length is very high. Phenotypic and genetic correlations with greasy fleece weight, yield, clean fleece weight, average fibre diameter and liveweight are in general agreement with other published estimates. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000 University of New South Wales, Sydney, Australia.

Ultrafine powders of SrTiO3 from the hydrothermal preparation and their catalytic activity in the photolysis of water

Ultrafine powders of SrTiO3 are prepared at 100–150°C by the hydrothermal method, starting from TiO2·xH2O gel and Sr(OH)2 and H2O-isopropanol mixed solvent as the medium, The X-ray diffractograms of the powder show line broadening. The minimum crystallite size obtained ranges from 5 to 20nm with 20% H2O-80% C3H7OH as the reaction medium, as estimated from X-ray half-peak widths and TEM studies. The electron diffraction results indicate high concentration of lattice defects in these crystallites. The optical spectra of the particle suspensions in water show that the absorption around the band gap is considerably broadened, together with the appearance of maxima in the far ultraviolet. Aqueous suspensions of SrTiO3 powders, as such, do not produce H2 or O2 on UV irradiation. After coating with rhodium, H2 and O2 are evolved on illumination. However, the turn over number of O2 is lower than the stoichiometrically expected values from the corresponding values of H2. No correlation of the photocatalytic activity with surface area is observed. The activity of Rh-SrTiO3 slowly deteriorates with extended period of irradiation.

Use of part records in Merino breeding programs - The inheritance of wool growth and fibre traits during different times of the year to determine their value in Merino breeding programs

Fibre diameter can vary dramatically along a wool staple, especially in the Mediterranean environment of southern Australia with its dry summers and abundance of green feed in spring. Other research results have shown a very low phenotypic correlation between fibre diameter grown between seasons. Many breeders use short staples to measure fibre diameter for breeding purposes and also to promote animals for sale. The effectiveness of this practice is determined by the relative response to selection by measuring fibre traits on a full 12 months wool staple as compared to measuring them only on part of a staple. If a high genetic correlation exists between the part record and the full record, then using part records may be acceptable to identify genetically superior animals. No information is available on the effectiveness of part records. This paper investigated whether wool growth and fibre diameter traits of Merino wool grown at different times of the year in a Mediterranean environment, are genetically the same trait, respectively. The work was carried out on about 7 dyebanded wool sections/animal.year, on ewes from weaning to hogget age, in the Katanning Merino resource flocks over 6 years. Relative clean wool growth of the different sections had very low heritability estimates of less than 0.10, and they were phenotypically and genetically poorly correlated with 6 or 12 months wool growth. This indicates that part record measurement of clean wool growth of these sections will be ineffective as indirect selection criteria to improve wool growth genetically. Staple length growth as measured by the length between dyebands, would be more effective with heritability estimates of between 0.20 and 0.30. However, these measurements were shown to have a low genetic correlation with wool grown for 12 months which implies that these staple length measurements would only be half as efficient as the wool weight for 6 or 12 months to improve total clean wool weight. Heritability estimates of fibre diameter, coefficient of variation of fibre diameter and fibre curvature were relatively high and were genetically and phenotypically highly correlated across sections. High positive phenotypic and genetic correlations were also found between fibre diameter, coefficient of variation of fibre diameter and fibre curvature of the different sections and similar measurements for wool grown over 6 or 12 months. Coefficient of variation of fibre diameter of the sections also had a moderate negative phenotypic and genetic correlation with staple strength of wool staples grown over 6 months indicating that coefficient of variation of fibre diameter of any section would be as good an indirect selection criterion to improve stable strength as coefficient of variation of fibre diameter for wool grown over 6 or 12 months. The results indicate that fibre diameter, coefficient of variation of fibre diameter and fibre curvature of wool grown over short periods of time have virtually the same heritability as that of wool grown over 12 months, and that the genetic correlation between fibre diameter, coefficient of variation of fibre diameter and fibre curvature on part and on full records is very high (rg > 0.85). This indicates that fibre diameter, coefficient of variation of fibre diameter and fibre curvature on part records can be used as selection criteria to improve these traits. However, part records of greasy and clean wool growth would be much less efficient than fleece weight for wool grown over 6 or 12 months because of the low heritability of part records and the low genetic correlation between these traits on part records and on wool grown for 12 months.

Preparation of CaTiO3 fine powders by the hydrothermal method

Fine powders consisting of 0.1–0.5 μm size crystallites of CaTiO3 are prepared at 150–200°C by the hydrothermal method starting from hydrated titania gel and reactive calcium oxide suspended as an aqueous slurry in an autoclave. The resulting high-purity CaTiO3 is characterised by TEM, X-ray powder diffraction, chemical analyses and sintering characteristics. The hydrothermally prepared CaTiO3 powders are sinterable to high-density ceramics below 1400°C. The dc conductivity behaviour of the chemically reduced ceramics is presented.

Hydrothermal preparation of Ba(Ti,Zr)O3 fine powders

Fine powders consisting of aggregated submicron crystallites of Ba(Ti,Zr)O3 in the complete range of Ti/Zr ratios are prepared at 85–130°C by hydrothermal method, starting from TiO2 + ZrO2 · xH2O mixed gel and Ba(OH)2 solution. The products obtained below 110°C incorporate considerable amounts of H2O and OH− within the lattice. As-prepared BaTiO3 is cubic and converts to tetragonal phase after the heat treatment at 1200°C, accompanied by the loss of residual hydroxyl ions. TEM investgations of the growth features show a transformation of the gel to the crystallite. Ba2+ ions entering the gel produce chemical changes within the gel, followed by dehydration, resulting in a cubic perovskite phase irrespective of Ti/Zr. The sintering properties of these powders to fine-grained, high density ceramics and their dielectric properties are presented.

Hydrothermal synthesis of Ba(Ti, Sn)O3 fine powders and dielectric properties of the corresponding ceramics

Fine powders of submicron-sized crystallites of BaTiO3 were prepared at 85–130°C by the hydrothermal method, starting from TiO2.ξH2O gel and Ba(OH)2 solution. The products obtained below 110°C incorporated considerable amounts of H2O and OH− in the lattice. As-prepared BaTiO3 is cubic and converts to the tetragonal phase after heat treatment at 1200°C, accompanied by the loss of residual OH− ions. Hydrothermal reaction of SnO2.ξH2O gel with Ba(OH)2 at 150–260°C gives rise to the hydrated phase, BaSn(OH)6.3H2O, due to the amphoteric nature of SnO2.ξH2O which stabilises Sn(OH)62− anions in basic media. On heating in air or releasing the pressure in situ at 260°C, BaSn(OH)6.3H2O converts to BaSnO3 through an intermediate, BaSnO(OH)4. Solid solutions of Ba(Ti,Sn)O3 are directly formed from (TiO2 + SnO2)..ξH2O gel up to 35 mol% SnO2. At higher Sn contents, the hydrothermal products are mixtures of BaSn(OH)6.3H2O and BaTiO3, which on annealing at 1000°C result in monophasic Ba(Ti,Sn)O3. The sintering characteristics and the dielectric properties of the ceramics prepared out of these fine powders are presented. The dielectric properties of fine-grained Ba(Ti,Sn)O3 ceramics are explained on the basis of the prevailing diffuse phase transition behaviour.

Precipitation of rutile and anatase (Tio12) fine powders and their conversion to MTiO3 (M = Ba, Sr, Ca) by the hydrothermal method

Fine powders of TiO2 (rutile) with high degree of crystallinity are formed from aqueous titanium oxychloride solution under hydrothermal conditions at 160–230°C and 15–100 kg/cm2 for 1–2 hours. The anatase phase is produced from the same medium when sulfate ion impurity is present, with Image . Both these fine powders are converted to BaTiO3, SrTiO3 or CaTiO3 when suspended in Ba(OH)2 or Sr(OH)2 solution or in an aqueous slurry of carbonate-free CaO with Image , at 180–280°C and 12–65 kg/cm2 for 4–8 hours. The resulting fine powders contain monocrystallites of the perovskite phase with 0.1–1.5 μm particle size.

Sacrificial photolysis of water on TiO2 fine powders prepared by the hydrothermal method

The often discussed role of surface hydroxylation of TiO2 particles as an essential characterestics for their photocatalytic activity can be verified by preparing TiO2 powders by hydrothermal method since hydroxylated surface layers will be better retained on these particles formed in superheated water. Thus, fine powders of TiO2 (rutile) with high degree of crystallinity are formed from titanium oxychloride in the mixed solvent of water and 2-propanol at 160–230°C and 20–120 atm. The anatase phase is produced from the same medium when sulfate ion impurity is present, with Image . TiO2 powders are washed free of anions and 2-propanol by ultrafiltration and are Pt mounted by a photochemical method. Aqueous suspensions of both forms of TiO2 neither as such nor after Pt-loading, do not produce H2 on band gap illumination whereas, H2 is generated in presence of hole scavengers such as EDTA, TEOA, sulfite or hypophosphite. The effects of hole scavenger concentration, Pt : TiO2 ratio, particulate suspension density and the nature of hole scavengers on H2 production are presented. Platinised rutile powders are equally active as anatase in sacrificial systems.

Production attributes of Merino sheep genetically divergent for wool growth are reflected in differing rumen microbiotas

Divergent genetic selection for wool growth as a single trait has led to major changes in sheep physiology and metabolism, including variations in rumen microbial protein production and uptake of α-amino nitrogen in portal blood. This study was conducted to determine if sheep with different genetic merit for wool growth exhibit distinct rumen bacterial diversity. Eighteen Merino wethers were separated into groups of contrasting genetic merit for clean fleece weight (CFW; low: WG− and high: WG+) and fed a blend of oaten and lucerne chaff diet at two levels of intake (LOI; 1 or 1.5 times maintenance energy requirements) for two seven-week periods in a crossover design. Bacterial diversity in rumen fluid collected by esophageal intubation was characterized using 454 amplicon pyrosequencing of the V3/V4 regions of the 16S rRNA gene. Bacterial diversity estimated by Phylogenetic distance, Chao1 and observed species did not differ significantly with CFW or LOI; however, the Shannon diversity index differed (P=0.04) between WG+ (7.67) and WG− sheep (8.02). WG+ animals had a higher (P=0.03) proportion of Bacteroidetes (71.9% vs 66.5%) and a lower (P=0.04) proportion of Firmicutes (26.6% vs 31.6%) than WG− animals. Twenty-four specific operational taxonomic units (OTUs), belonging to the Firmicutes and Bacteroidetes phyla, were shared among all the samples, whereas specific OTUs varied significantly in presence/abundance (P<0.05) between wool genotypes and 50 varied (P<0.05) with LOI. It appears that genetic selection for fleece weight is associated with differences in rumen bacterial diversity that persist across different feeding levels. Moderate correlations between seven continuous traits, such as methane production or microbial protein production, and the presence and abundance of 17 OTUs were found, indicating scope for targeted modification of the microbiome to improve the energetic efficiency of rumen microbial synthesis and reduce the greenhouse gas footprint of ruminants.

Sinteractive anodic powders improve densification and electrochemical properties of BaZr0.8Y0.2O3-δ electrolyte films for anode-supported solid oxide fuel cells

The difficult sintering of BaZr0.8Y0.2O 3-δ (BZY20) powders makes the fabrication of anode-supported BZY20 electrolyte films complex. Dense BZY20 membranes were successfully fabricated on anode substrates made of sinteractive NiO-BZY20 powders, prepared by a combustion method. With respect to traditional anode substrates made of powders prepared by mechanical mixing, the anode substrates made of the wet-chemically synthesized composite NiO-BZY20 powders significantly promoted the densification of BZY20 membranes: dense BZY20 films were obtained after co-pressing and co-firing at 1300 °C, a much lower temperature than those usually needed for densifying BZY20 membranes. Improved electrochemical performance was also observed: the supported BZY20 films maintained a high proton conductivity, up to 5.4 × 10-3 S cm-1 at 700 °C. Moreover, an anode-supported fuel cell with a 30 m thick BZY20 electrolyte film fabricated at 1400 °C on the anode made of the wet-chemically synthesized NiO-BZY20 powder showed a peak power density of 172 mW cm-2 at 700 °C, using La0.6Sr0.4Co 0.2Fe0.8O3-δ-BaZr0.7Y 0.2Pr0.1O3-δ as the cathode material, with a remarkable performance for proton-conducting solid oxide fuel cell (SOFC) applications.

BaZr0.8Y0.2O3--NiO composite anodic powders for proton-conducting SOFCs prepared by a combustion method

BaZr0.8Y0.2O3- (BZY)-NiO composite powders with different BZY-NiO weight ratios were prepared by a combustion method as anodes for proton-conducting solid oxide fuel cells (SOFCs). After heating to 1100C for 6 h, the composite powders were made of a well-dispersed mixture of two phases, BZY and NiO. Chemical stability tests showed that the BZY-NiO anodic powders had good stability against CO2, whereas comparative tests under the same conditions showed degradation for BaCe0.7Zr 0.1Y0.2O3--NiO, which is at present the most used anode material for proton-conducting SOFCs. Area specific resistance (ASR) measurements for BZY-NiO anodes showed that their electrochemical performance depended on the BZY-NiO weight ratio. The best performance was obtained for the anode containing 50 wt BZY and 50 wt NiO, which showed the smallest ASR values in the whole testing temperature range (0.37 cm2 at 600C). The 50 wt BZY and 50 wt NiO anode prepared by combustion also showed superior performance than that of the BZY-NiO anode conventionally made by a mechanical mixing route, as well as that of Pt.

Sacrificial photolysis of water on Ti1−xSnxO2 ultrafine powders

Ultrafine powders of extra pure Ti1−xSnxO2, where o < x < 1, prepared by the hydrothermal method are pale yellow in color. They show photocatalytic activity after platinization, in the visible light (420–550 nm) for H2-production from aqueous solutions containing sacrificial donors such as hypophosphite. The spectral sensitization is shown to be due to peroxotitanium species in the rutile-type structure. Peroxide ion, O22−, arises from the dimerization of O−, the hole centres, produced during the disproportionative decomposition of residual hydroxyls: OH− = O− + H. Higher OH contents in TixSnxO2 is due to the amphoteric chemistry of oxocompounds of tin.

Characterization of barium titanate fine powders formed from hydrothermal crystallization

A detailed evaluation of size, shape and microstrains of BaTiO3 crystallites produced by hydrothermal crystallization at 90 – 180 °C and 0.1 – 1.2 MPa, from amorphous TiO2· xH2O (3 < × < 8) gel and aqueous Ba(OH)2 is presented, using X-ray line-broadening and TEM studies. Whereas the concentration of Ba(OH)2 and the acceptor impurities affect the crystallite shape, the stoichimetry with respect to Ba/Ti, donor as well as acceptor impurities, and the temperature of crystallization influence the microstrains. It is shown that strains in the crystallites are related to the point defects in the lattice. Compensation of the residually present hydroxyl ions in the oxygen sublattice by cation vacancies results in strains leading to metastable presence of the cubic phase at room temperature. Studies on the diffuse phase transition behaviour of these submicron powders show that the stable tetragonal phase is produced only on annealing at high temperatures where the mobility of cations vacancies are larger. Heat-treatment reduces anisotropy and strain in undoped samples, whereas annealing is less effective in doped materials. Comparison of the crystillite size by TEM showed better agreement with the Warren—Averbach method.

Combustion Synthesis of Metal Chromite Powders

Fine-particle metal chromites (MCr2O4, where M = Mg, Ca, Mn, Fe, Co, Ni, Cu, and Zn) have been prepared by the combustion of aqueous solutions containing the respective metal nitrate, chromium(III) nitrate, and urea in stoichiometric amounts. The mixtures, when rapidly heated to 350°C, ignite and yield voluminous chromites with surface areas ranging from 5 to 25 m2/g. MgCr2O4, sintered in air at 1500°C for 5 h, has a density of 4.0 g/cm3.