968 resultados para wood reintroduction
Resumo:
Optimal matching of species to sites is required for a sustainable hardwood plantation industry in the subtropics. This paper reports the performance and adaptation of 60 taxa (species, provenances and hybrids) across two rainfall zones and a range of soil types in southern Queensland. Specifically, performance of taxa is compared across five replicated taxon–site matching trials at age 6 y. Three trials are in a 1000-mm y–1 rainfall zone of the Wide Bay region near Miriam Vale and two in a drier (about 750 mm y–1) rainfall zone near Kingaroy in the South Burnett region. In the higher-rainfall zone, the taxa with the fastest growth in the three trials at age 6 y were Corymbia citriodora subsp. variegata Woondum provenance, which ranked 1st, 6th and 5th respectively; E. longirostrata Coominglah provenance, ranked 3rd, 2nd and 3rd; and two sources of E. grandis, Copperlode provenance (ranked 4th and 1st) and SAPPI seed orchard (ranked 6th and 4th), which were planted in only two of the three trials. Similarly, in the lower-rainfall zone, E. grandis and its hybrids appear promising from the 6-y growth data., This excellent early growth, however, has not continued in either rainfall zone, with these taxa, 8 y after planting, now showing signs of stress and mortality. Based on trial results in these two rainfall zones, the taxon that appears the most promising for sustainable plantation development with high average annual volume index values and low incidence of borer attack is Corymbia citriodora subsp. variegata (6.7 m³ ha–1). Eucalyptus grandis and E. longirostrata both have better average annual volume indexes (8.2 m³ ha–1 and 7.4 m³ ha–1 respectively) but are very susceptible to borer attack. The current and long-term productivity and sustainability of plantation forestry in these rainfall zones is discussed. Further, the implications of predicted climate change (particularly reduced rainfall) for growing trees for fibre production and carbon sequestration are explored.
Resumo:
Characterisation and investigation of a number of key wood properties, critical for further modelling work, has been achieved. The key results were: • Morphological characterisation, in terms of fibre cell wall thickness and porosity, was completed. A clear difference in fibre porosity, size, wall thickness and orientation was evident between species. Results were consistent with published data for other species. • Viscoelastic properties of wood were shown to differ greatly between species and in the radial and tangential directions, largely due to anatomical and chemical variations. Consistent with published data, the radial direction shows higher stiffness, internal friction and glass transition temperature than the tangential directions. The loss of stiffness over the measured temperature range was greater in the tangential direction than the radial direction. Due to time dependant molecular relaxation, the storage modulus and glass transition temperature decreased with decreasing test frequency, approaching an asymptotic limit. Thus the viscoelastic properties measured at lower frequencies are more representative of static material. • Dynamic interactions between relative humidity, moisture content and shrinkage of four Australian hardwood timbers can be accurately monitored on micro-samples using a specialised experimental device developed by AgroParisTech – ENGREF. The device generated shrinkage data that varied between species but were consistent (repeatable) within a species. Collapse shrinkage was clearly evident with this method for Eucalyptus obliqua, but not with other species, consistent with industrial seasoning experience. To characterise the wood-water relations of this species, free of collapse, thinner sample sections (in the R-T plane) should be used.
Resumo:
The Juvenile Wood Initiative (JWI) project has been running successfully since July 2003 under a Research Agreement with FWPA and Letters of Association with the consortium partners STBA (Southern Tree Breeding Association), ArborGen and FPQ (Forestry Plantations Queensland). Over the last five and half years, JWI scientists in CSIRO, FPQ, and STBA have completed all 12 major milestones and 28 component milestones according to the project schedule. We have made benchmark progress in understanding the genetic control of wood formation and interrelationships among wood traits. The project has made 15 primary scientific findings and several results have been adopted by industry as summarized below. This progress was detailed in 10 technical reports to funding organizations and industry clients. Team scientists produced 16 scientific manuscripts (8 published, 1 in press, 2 submitted, and several others in the process of submission) and 15 conference papers or presentations. Primary Scientific Findings. The 15 major scientific findings related to wood science, inheritance and the genetic basis of juvenile wood traits are: 1. An optimal method to predict stiffness of standing trees in slash/Caribbean pine is to combine gravimetric basic density from 12 mm increment cores with a standing tree prediction of MoE using a time of flight acoustic tool. This was the most accurate and cheapest way to rank trees for breeding selection for slash/Caribbean hybrid pine. This method was also recommended for radiata pine. 2. Wood density breeding values were predicted for the first time in the STBA breeding population using a large sample of 7,078 trees (increment cores) and it was estimated that selection of the best 250 trees for deployment will produce wood density gains of 12.4%. 3. Large genetic variation for a suite of wood quality traits including density, MFA, spiral grain, shrinkage, acoustic and non-acoustic stiffness (MoE) for clear wood and standing trees were observed. Genetic gains of between 8 and 49% were predicted for these wood quality traits with selection intensity between 1 to 10% for radiata pine. 4. Site had a major effect on juvenile-mature wood transition age and the effect of selective breeding for a shorter juvenile wood formation phase was only moderate (about 10% genetic gain with 10% selection intensity, equivalent to about 2 years reduction of juvenile wood). 5. The study found no usable site by genotype interactions for the wood quality traits of density, MFA and MoE for both radiata and slash/Caribbean pines, suggesting that assessment of wood properties on one or two sites will provide reliable estimates of the genetic worth of individuals for use in future breeding. 6. There were significant and sizable genotype by environment interactions between the mainland and Tasmanian regions and within Tasmania for DBH and branch size. 7. Strong genetic correlations between rings for density, MFA and MoE for both radiata and slash/Caribbean pines were observed. This suggests that selection for improved wood properties in the innermost rings would also result in improvement of wood properties in the subsequent rings, as well as improved average performance of the entire core. 8. Strong genetic correlations between pure species and hybrid performance for each of the wood quality traits were observed in the hybrid pines. Parental performance can be used to identify the hybrid families which are most likely to have superior juvenile wood properties of the slash/Caribbean F1 hybrid in southeast Queensland. 9. Large unfavourable genetic correlations between growth and wood quality traits were a prominent feature in radiata pine, indicating that overcoming this unfavourable genetic correlation will be a major technical issue in progressing radiata pine breeding. 10. The project created the first radiata pine 18 k cDNA microarray and generated 5,952 radiata pine xylogenesis expressed sequence tags (ESTs) which assembled into 3,304 unigenes. 11. A total of 348 genes were identified as preferentially expressed genes in earlywood or latewood while a total of 168 genes were identified as preferentially expressed genes in either juvenile or mature wood. 12. Juvenile earlywood has a distinct transcriptome relative to other stages of wood development. 13. Discovered rapid decay of linkage disequilibrium (LD) in radiata pine with LD decaying to approximately 50% within 1,700 base pairs (within a typical gene). A total of 913 SNPS from sequencing 177,380 base pairs were identified for association genetic studies. 14. 149 SNPs from 44 genes and 255 SNPs from a further 51 genes (total 95 genes) were selected for association analysis with 62 wood traits, and 30 SNPs were shortlisted for their significant association with variation of wood quality traits (density, MFA and MoE) with individual significant SNPs accounting for between 1.9 and 9.7% of the total genetic variation in traits. 15. Index selection using breeding objectives was the most profitable selection method for radiata pine, but in the long term it may not be the most effective in dealing with negative genetic correlations between wood volume and quality traits. A combination of economic and biological approaches may be needed to deal with the strong adverse correlation.
Resumo:
An integrated approach to energy planning, when applied to large hydroelectric projects, requires that the energy-opportunity cost of the land submerged under the reservoir be incorporated into the planning methodology. Biomass energy lost from the submerged land has to be compared to the electrical energy generated, for which we develop four alternative formulations of the net-energy function. The design problem is posed as an LP problem and is solved for two sites in India. Our results show that the proposed designs may not be viable in net-energy terms, whereas a marginal reduction in the generation capacity could lead to an optimal design that gives substantial savings in the submerged area. Allowing seasonal variations in the hydroelectric generation capacity also reduces the reservoir size. A mixed hydro-wood generation system is then examined and is found to be viable.
Resumo:
This manual describes best practice for producing high-value flooring products from coconut ‘wood’—or cocowood. It meets international standards for flooring products and accounts for the recognised, specific, local conditions of the Pacific Islands. The information is intended for operators skilled in timber processing, who need to work with the unusual properties of cocowood, and specifies where cocowood processes differ from standard practice for timber. For other processes, refer to the relevant standards set by the importing country. These technical guidelines are based on the research outcomes of the ACIAR project, 'Improving value and marketability of coconut wood'. The manual is divided into three chapters. Each chapter adds to different aspects of primary and secondary processing. Chapter 1 provides an overview of the best practice steps for harvesting and processing cocowood. There is also a glossary of terms specifically associated with processing cocowood and a section on managing processing risks. Chapter 2 covers cocowood’s unique properties and how they relate to critical processing techniques. This is followed by sections that set out the processing methods in more detail, explaining why these practices are essential when working with cocowood. Chapter 3 provides more information, including contacts, current timber standards and some useful publications.
Resumo:
Khaya senegalensis, African mahogany, a high-value hardwood, was introduced in the Northern Territory (NT) in the 1950s; included in various trials there and at Weipa, Q in the 1960s-1970s; planted on ex mine sites at Weipa (160 ha) until 1985; revived in farm plantings in Queensland and in trials in the NT in the 1990s; adopted for large-scale, annual planting in the Douglas-Daly region, NT from 2006 and is to have the planted area in the NT extended to at least 20,000 ha. The recent serious interest from plantation growers, including Forest Enterprises Australia Ltd (FEA), has seen the establishment of some large scale commercial plantations. FEA initiated the current study to process relatively young plantation stands from both Northern Territory and Queensland plantations to investigate the sawn wood and veneer recovery and quality from trees ranging from 14 years (NT – 36 trees) to 18-20 years (North Queensland – 31 trees). Field measures of tree size and straightness were complemented with log end splitting assessment and cross-sectional disc sample collection for laboratory wood properties measurements including colour and shrinkage. End-splitting scores assessed on sawn logs were relatively low compared to fast grown plantation eucalypts and did not impact processing negatively. Heartwood proportion in individual trees ranged from 50% up to 92 % of butt cross-sectional disc area for the visually-assessed dark coloured central heartwood and lighter coloured transition wood combined. Dark central heartwood proportion was positively related to tree size (R2 = 0.57). Chemical tests failed to assist in determining heartwood – sapwood boundary. Mean basic density of whole disc samples was 658 kg/m3 and ranged among trees from 603 to 712 kg/m3. When freshly sawn, the heartwood of African mahogany was orange-red to red. Transition wood appeared to be pinkish and the sapwood was a pale yellow colour. Once air dried the heartwood colour generally darkens to pinkish-brown or orange-brown and the effect of prolonged time and sun exposure is to darken and change the heartwood to a red-brown colour. A portable colour measurement spectrophotometer was used to objectively assess colour variation in CIE L*, a* and b* values over time with drying and exposure to sunlight. Capacity to predict standard colour values accurately after varying periods of direct sunlight exposure using results obtained on initial air-dried surfaces decreased with increasing time to sun exposure. The predictions are more accurate for L* values which represent brightness than for variation in the a* values (red spectrum). Selection of superior breeding trees for colour is likely to be based on dried samples exposed to sunlight to reliably highlight wood colour differences. A generally low ratio between tangential and radial shrinkages was found, which was reflected in a low incidence of board distortion (particularly cupping) during drying. A preliminary experiment was carried out to investigate the quality of NIR models to predict shrinkage and density. NIR spectra correlated reasonably well with radial shrinkage and air dried density. When calibration models were applied to their validation sets, radial shrinkage was predicted to an accuracy of 76% with Standard Error of Prediction of 0.21%. There was also a strong predictive power for wood density. These are encouraging results suggesting that NIR spectroscopy has good potential to be used as a non-destructive method to predict shrinkage and wood density using 12mm diameter increment core samples. Average green off saw recovery was 49.5% (range 40 to 69%) for Burdekin Agricultural College (BAC) logs and 41.9% (range 20 to 61%) for Katherine (NT) logs. These figures are about 10% higher than compared to 30-year-old Khaya study by Armstrong et al. (2007) however they are inflated as the green boards were not docked to remove wane prior to being tallied. Of the recovered sawn, dried and dressed volume from the BAC logs, based on the cambial face of boards, 27% could potentially be used for select grade, 40% for medium feature grade and 26% for high feature grades. The heart faces had a slightly higher recovery of select (30%) and medium feature (43%) grade boards with a reduction in the volume of high feature (22%) and reject (6%) grade boards. Distribution of board grades for the NT site aged 14 years followed very similar trends to those of the BAC site boards with an average (between facial and cambial face) 27% could potentially be used for select grade, 42% for medium feature grade, 26% for high feature grade and 5% reject. Relatively to some other subtropical eucalypts, there was a low incidence of borer attack. The major grade limiting defects for both medium and high feature grade boards recovered from the BAC site were knots and wane. The presence of large knots may reflect both management practices and the nature of the genetic material at the site. This stand was not managed for timber production with a very late pruning implemented at about age 12 years. The large amount of wane affected boards is indicative of logs with a large taper and the presence of significant sweep. Wane, knots and skip were the major grade limiting defects for the NT site reflecting considerable amounts of sweep with large taper as might be expected in younger trees. The green veneer recovered from billets of seven Khaya trees rotary peeled on a spindleless lathe produced a recovery of 83% of green billet volume. Dried veneer recovery ranged from 40 to 74 % per billet with an average of 64%. All of the recovered grades were suitable for use in structural ply in accordance to AS/NZ 2269: 2008. The majority of veneer sheets recovered from all billets was C grade (27%) with 20% making D grade and 13% B grade. Total dry sliced veneer recovery from the logs of the two largest logs from each location was estimated to be 41.1%. Very positive results have been recorded in this small scale study. The amount of colour development observed and the very reasonable recoveries of both sawn and veneer products, with a good representation of higher grades in the product distribution, is encouraging. The prospects for significant improvement in these results from well managed and productive stands grown for high quality timber should be high. Additionally, the study has shown the utility of non-destructive evaluation techniques for use in tree improvement programs to improve the quality of future plantations. A few trees combined several of the traits desired of individuals for a first breeding population. Fortunately, the two most promising trees (32, 19) had already been selected for breeding on external traits, and grafts of them are established in the seed orchard.
Resumo:
Riga 1878? – New York 1959
Resumo:
Riga 1878? – New York 1959
Resumo:
Hermann (Lazar Hirsch) Judey, born 1878 Riga and died 1959 New York; Olga Judey nee Fischmann, 1878-1929
Resumo:
Paul was the son from a previous marriage of Hermann's first wife Olga Judey nee Fischmann
Resumo:
Study to investigate the use of cypress pine extractives as a novel timber preservative.
Resumo:
Support Horticulture and Forestry Science tree improvement activities with sampling and evaluation of wood properties to rank for wood quality for specified product types (pulp and paper, solid wood, veneer etc).
Resumo:
To improve the yield of marketable high value sawn and/or veneer timber from young plantation grown eucalypts: through the greater understanding and management of growth stresses; grain angle; juvenile wood; and other important wood properties.
Resumo:
To refine the emerging silvicultural systems for sub-tropical eucalypt plantations to produce logs of acceptable dimensions and quality for processing into high-value solid and engineered wood products, while maintaining financial attractiveness for growers. The available resources are focussed primarily on sub-tropical Corymbia plantings.
Resumo:
Managing subtropical pines for improved wood production based on a better understanding of genetics, silviculture, environment and their interactions.