Modelling effects of axial load on behaviour of pile groups in laterally-spreading soil

Previous research into the behaviour of piled foundations in laterally-spreading soil deposits has concentrated on pile groups that carry small or negligible axial loads. This paper presents dynamic centrifuge test results for 2×2 pile groups with bending and geometric properties similar to real 0.5m diameter tubular steel and solid circular reinforced-concrete field piles. Axial loads applied represented upper-bounds on typical working loads. The simultaneous scaling of the relevant properties controlling both lateral and axial behaviour allows comparisons to be drawn regarding the particular mechanisms of failure that would dominate for each type of pile. Flexible reinforced-concrete piles which tend to carry lower loads were found to be dominated by lateral effects, while steel piles, which are much stiffer and usually carry greater loads are dominated by settlement considerations. © 2006 Taylor & Francis Group, London.

Experimental validation of a drive-by stiffness identification method for bridge monitoring

An experimental investigation is carried out to verify the feasibility of using an instrumented vehicle to detect and monitor bridge dynamic parameters. The low-cost method consists of the use of a moving vehicle fitted with accelerometers on its axles. In the laboratory experiment, the vehicle–bridge interaction model consists of a scaled two-axle vehicle model crossing a simply supported steel beam. The bridge model also includes a scaled road surface profile. The effects of varying the vehicle model configuration and speed are investigated. A finite element beam model is calibrated using the experimental results, and a novel algorithm for the identification of global bridge stiffness is validated. Using measured vehicle accelerations as input to the algorithm, the beam stiffness is identified with a reasonable degree of accuracy.

Rod length influence in torque measurement of SPT-T test

Since Ranzini suggested supplementing the SPT test with measurement of the torque required to turn the split spoon sampler after driving, many Brazilian engineers have been using this in the design of pile foundations. This paper presents a study of the rod length influence in the torque measurement. A theoretical study of material resistance considering torsion and bending in a thin wall tubular steel shaft was performed. It makes possible to conclude that the shearing tension caused by the proper weight represents less than 1% of the shearing tension caused by the turning moment. In addition, an experimental study was done with electric torquemeters fixed in a horizontal rod system. The tests were being carried out to analyze rods of one meter to twenty meters in length and the measurements were collected at the ends of each rod length verifying the efficiency data. As a result, it is possible to verify that the torque difference through rod length is lower than minimum scales of mechanical torquemeters that are used on practical engineering. Also a fact to be considered is a big torque loss for values under 20 N.m of applied torque. This way, the SPT-T is not adequate to low consistency soil. Copyright ASCE 2007.

Composite connections in slim-floor system: An experimental study

This paper reports the results of full-scale tests in beam-to-column connections for composite slim floor systems, including tests on Bare Steel connection and composite connection. The tested system consists of a concrete-filled composite column and a composite floor where an asymmetric steel beam is connected to a composite column by shear steel plates. Tests results previously obtained on partially encased composite beams were used to define the position of the headed studs in the slim floor system. Based on the obtained results of connections, the composite and Bare Steel connection behaved as semi-rigid and nominally pinned respectively. The tests results also indicated a significant contribution of the slim floor to the moment capacity of the connection. (C) 2011 Elsevier Ltd. All rights reserved.

Studio del comportamento flesso-torsionale di un telaio in materiale composito per vettura sportiva

Lo studio svolto in merito alle tecniche di produzione di componenti strutturali in materiale composito ha permesso il raggiungimento di una precisa consapevolezza dello stato dell’arte del settore, in particolare in riferimento ai processi attualmente utilizzati per l’industrializzazione in media-grande serie. Con l’obiettivo di sintetizzare i principali vantaggi delle tecnologie suddette e permettere la realizzazione di forme più complesse, si è proceduto all’analisi di fattibilità, attraverso uno studio funzionale e una prima progettazione di una tecnologia di produzione per nastratura automatizzata di componenti strutturali in materiale composito. Si è voluto quindi dimostrare la flessibilità e la consistenza del processo disegnando un telaio nastrato in carbonio, intercambiabile al telaio FSAE 2009 in tubolare d’acciaio (stessi punti di attacco motore, punti di attacco telaietto posteriore, attacchi sospensioni anteriori) e che garantisca un sostanziale vantaggio in termini di peso, a pari rigidezza torsionale. La caratterizzazione di tale telaio è stata eseguita mediante l'utilizzo del calcolo strutturale, validato da prove sperimentali.

Calibration of calculation models of wooden guardrails with Operational Modal Analysis

This study analyses the differences between two calculation models for guardrails on building sites that use wooden boards and tubular steel posts. Wood was considered an isotropic material in one model and an orthotropic material in a second model. The elastic constants of the wood were obtained with ultrasound. Frequencies and vibration modes were obtained for both models through linear analysis using the finite element method. The two models were experimentally calibrated through operational modal analysis. The results obtained show that for the three types of wood under analysis, the model which considered them as an orthotropic material fitted the experimental results better than the model which considered them as an isotropic material.

La silla de la discordia : la pequeña escala como campo de experimentación en la modernidad : Breuer, Mies y Stam

El siglo XIX fue un siglo dedicado a los grandes edificios públicos. Los teatros, las academias, los museos. Sin embargo la arquitectura durante el siglo XX se dedicará al estudio de la casa. Todos los usos y tipologías se verán fuertemente revisados pero el núcleo de todos los esfuerzos y verdadero inicio de la arquitectura moderna será la vivienda. A partir de ella todos los preceptos modernos se irán aplicando a los distintos programas. Nikolaus Pevsner señala a William Morris como el primer arquitecto moderno porque precisamente entendió que un arte verdaderamente social, en consonancia con su tiempo y la sociedad a la que sirve, ha de ocuparse de aquello que preocupe a la gente. Con la nueva situación de la vivienda en el centro de las motivaciones disciplinares el mueble adopta un nuevo protagonismo. En un momento avanzado de su carrera Marcel Breuer observa entre curioso e irónico cómo el mueble moderno había sido promocionado paradójicamente no por los diseñadores de muebles sino por los arquitectos1. La respuesta la da Le Corbusier en una de sus conferencias de 1931 recogida en Precisiones 2 cuando señala la reformulación del mobiliario como el "nudo gordiano" de cuya resolución pendía la renovación de la planta moderna. El Movimiento Moderno se había visto obligado a atacar este tema para poder avanzar en sus propuestas domésticas. El Movimiento Moderno se propuso solucionar los problemas de la vivienda y de una Europa en reconstrucción pero se exigía además ser capaz de aportar una visión propositiva de la vida moderna. No se trataba únicamente de resolver los problemas ya existentes sino que además había la necesidad autoimpuesta de anticipar la domesticidad del futuro. Para ello sus viviendas al completo, mueble e inmueble, debían de presentarse bajo esa nueva imagen. El manifiesto fundacional de la Deustcher Werkbund extendía el radio de acción del nuevo arquitecto desde la construcción de las ciudades a los cojines del sofá. Este mobiliario tenía la compleja misión de condensar sintéticamente todos esos ideales que la modernidad había traído consigo: abstracción, higiene, fascinación maquínica, confianza positivista en la ciencia o la expresión material optimizada. Objetos de la vida moderna, en palabras de Le Corbusier, susceptibles de suscitar un estado de vida moderno. Pocas sillas en la historia del diseño habrán acarreado tanta polémica y tanta disputa por su autoría como la sillas voladas de tubo de acero en sus diferentes versiones. Para entenderlo situémonos en el año 1927 a las puertas de la exposición "Die Wohnung" ("La vivienda") organizada por los maestros de la Bauhaus y dirigida por Mies van der Rohe en la ladera Weissenhof de Stuttgart. Muchos nombres célebres de la arquitectura mostraron en esa ocasión su personal propuesta para la vivienda moderna y los objetos que la habitan. Entre ellos los muebles con tubo de acero fueron una presencia constante en la exposición pero hubo una pieza que destacó sobre todas las demás por su novedad y audacia. La pieza en cuestión era el modelo de silla volada, esto es, sin apoyos posteriores y cuya rigidez estaba conferida al esfuerzo solidario de la estructura continua de tubo de acero y que terminaría por convertirse en el cruce de caminos de tres figuras de la disciplina arquitectónica: Marcel Breuer, Mies van der Rohe y Mart Stam. Cada uno de ellos desarrolló su propio modelo de silla volada en sus versiones MR por parte de Mies, L&C Arnold de Stam y el posterior modelo BR 33 de Marcel Breuer. Los tres, en algún momento de su vida reclamaron de uno u otro modo su autoría como objetos que les pertenecían intelectualmente. Estas sillas se convirtieron en la expresión máxima de uno de los ansiados anhelos de la modernidad, la propia materialidad del acero, en su versión optimizada, era la que había derivado en una forma completamente nueva de un objeto cotidiano y cuyo tipo estaba ya totalmente asumido. Los nuevos materiales y las nuevas formas de hacer habían irrumpido hasta en los utensilios domésticos, y habían sido capaces de reformularlos. El punto de partida para esta investigación es precisamente esa coincidencia de tres figuras de la arquitectura moderna, los tres de formación artesanal, en un mismo modelo de silla y en una misma fecha. Tres arquitectos que se habían encargado de asegurar que el movimiento moderno no reconocía problemas formales sino solamente de construcción, iban a coincidir en el mismo tiempo y lugar, precisamente en una misma forma, como si tal coincidencia hubiera sido producto de una voluntad de época. Sin embargo el interés de este estudio no radica en una indagación sobre la autoría sino sobre cómo un mismo objeto resulta ser propositivo e interesante en campos muy diversos y la forma en que cada uno lo hace suyo incorporándolo a su propia investigación proyectual. La silla, más allá de ser un objeto de diseño exclusivamente, trasciende su propia escala para situarse inmersa en un proceso de búsqueda y exploración a nivel conceptual, formal, constructivo y estructural en la arquitectura cada uno de ellos. En un momento en que el oficio del arquitecto está siendo intensamente redefinido considero especialmente pertinente esta investigación, que en definitiva versa sobre la forma distintiva en que el pensamiento arquitectónico es capaz de proyectarse sobre cualquier disciplina para reformularla. ABSTRACT The nineteenth century was a century dedicated to the great public buildings; theaters, schools or museums. However the architecture in the twentieth century was devoted to the study of housing. All uses and typologies were heavily revised but the focus of all efforts and true beginning of modern architecture was housing. From these beginnings all modern precepts were applied to the various programs. Nikolaus Pevsner points to William Morris as the first modern architect precisely because he understood that a truly social art in line with its time and the society it serves must deal with social concerns at that time. With the new housing situation at the center of disciplinary concerns furniture took on a new prominence. At an advanced stage of his career Marcel Breuer observed partly with curiosity, partly with irony how modern furniture had been promoted not by furniture designers but by architects. The answer is given by Le Corbusier in one of his lectures of 1931 collected in Precisions when he pointed the reformulation of furniture as the "Gordian knot" for the renewal of modern plan resolution. Modernism had been forced to confront this issue in order to advance their domestic approaches. Modernism not only put forward a solution to the problems of housing and a Europe under reconstruction but is also needed to be able to contribute to an exciting vision of modern life. Not only did solve existing problems but also it had the self-imposed necessity of anticipating future domesticity and to do their houses full, movable and immovable, they should be submitted under this new image. The founding manifesto of the Deutsche Werkbund extended the scope of the new architect from building cities to the couch cushions. This furniture had the complex mission of synthetically condensing all the ideals of modernity had brought with it: abstraction, hygiene, mechanization, positivist confidence in science or material expression. Objects of modern life, in words of Le Corbusier, were likely to give rise a state of modern life. Few chairs in design history have resulted in so much controversy and so much dispute over their invention as the various versions of cantilevered tubular steel chairs. To understand this let us place ourselves in 1927 at the gates of the exhibition "Die Wohnung" ("Housing") organized by the teachers of the Bauhaus and directed by Mies van der Rohe in Stuttgart Weissenhoflung. Many famous names in architecture at that time showed their personal proposals for modern housing and the objects that inhabit them. Amongst these objects, the steel tube furniture was a constant presence at the exhibition but there was a piece so audacious that it stood out from all the others. This piece in question was the cantilever model chair, that is, which had no further rear support and whose rigidity was attributed to the solidity of its continues structure of steel tube. This piece would eventually become the crossroads of three very different personalities: Mart Stam, Marcel Breuer and Mies van der Rohe. Each of them developed their own model of cantilevered chair in different versions; The MR model developed by Mies van der Rohe, the L&C by Arnold Stam and a later model BR 33 by Marcel Breuer, and the three, at some point in their lives demanded the authorship of its invention as objects that belonged to them intellectually. These chairs epitomized one of the coveted objects of modernity, steel material in its optimized version, was what had led to a completely new form of an everyday object whose this type was fully adopted on board in design. New materials and production methods had burst into world of household objects, and had been able to reformulate their design. The bold design then became a dark object of controversy. The starting point for this doctoral thesis is the concurrent invention of the same model of chair by three different figures of modern architecture. These three architects, who were responsible for ensuring that the modern movement considered construction rather than form as the main design consideration, were working in the same place and at the same point in time. It was almost as if these three architects were shaped by the culture of the time (Zeitgeist). However the focus of this study lies not in an investigation of responsibility of ownership but in the investigation fo how the same object can turn out to be purposeful and interesting in many different fields and the way in which each researcher makes it his own by developing his own project research. 1927, the year of their meeting, was a initiatory year in the career of our players. The chair, beyond being only a design object transcended its own scale and became immersed in a process of research and development on a conceptual, formal, structural and constructive level in the architectural approach of each of the architects. At a time when the role of the architect is being redefined intensely I consider this research, which ultimately concerns the distinctive way the architectural thought can be projected onto and reformulate any discipline, to be particularly relevant.

Strengthening of circular hollow steel tubular sections using high modulus CFRP sheets

This paper describes the behaviour of very high strength (VHS) circular steel tubes strengthened by carbon fibre reinforced polymer (CFRP) and subjected to axial tension. A series of tests were conducted with different bond lengths and number of layers. The distribution of strain through the thickness of CFRP layers and along CFRP bond length was studied. The strain was found to generally decrease along the CFRP bond length far from the joint. The strain through the thickness of the CFRP layers was also found to decrease from bottom to top layer. The effective bond length for high modulus CFRP was established. Finally empirical models were developed to estimate the maximum load for a given CFRP arrangement.

Bolted beam-column moment connections between cold-formed steel members

ABSTRACT Twelve beam-to-column connections between cold-formed steel sections consisting of three beam depths and four connection types were tested in isolation to investigate their behavior based on strength, stiffness and ductility. Resulting moment-rotation curves indicate that the tested connections are efficient moment connections where moment capacities ranged from about 65% to 100% of the connected beam capac-ity. With a moment capacity of greater than 80% of connected beam member capacity, some of the connec-tions can be regarded as full strength connections. Connections also possessed sufficient ductility with rota-tions of 20 mRad at failure although some connections were too ductile with rotations in excess of 30 mRad. Generally, most of the connections possess the strength and ductility to be considered as partial strength con-nections. The ultimate failures of almost all of the connections were due to local buckling of the compression web and flange elements of the beam closest to the connection.

Mechanical performances of track-shaped rebar stiffened concrete-filled steel tubular (SCFRT) stub columns under axial compression

This paper presents a combined experimental, numerical, and theoretical study on the mechanical behaviors of track-shaped concrete-filled steel tubular (SCFRT) stub columns stiffened by rebars under compressive load. A total of 18 track-shaped concrete-filled steel tubular specimens including 12 specimens stiffened by rebars and 6 non-stiffened counterparts are tested, with consideration of parameters including flakiness ratio, concrete strength, and stiffeners. Failure pattern, bearing capacity, and ductility are all analyzed and discussed based on the experimental results. The numerical simulation by finite element (FE) software ABAQUS is also conducted. Based on both experimental and numerical results, theoretical formula to predict the load-bearing capacity of SCFRT stub columns subjected to axial compression loading is established according to the superposition principle of ultimate load-bearing capacity with rational simplification. The proposed theoretical method provides accurate predictions on the load bearing capacity by comparing with experimental results from 18 groups of specimens.

Electron Beam Surface Treatment. Part I: Surface Hardening of AISI D3 Tool Steel

The effects of electron beam surface hardening treatment on the microstructure and hardness of AISI D3 tool steel have been investigated in this paper. The results showed that the microstructure of the hardened layer consisted of martensite, a dispersion

Electron Beam Surface Remelting of AISI D2 Cold-Worked Die Steel

Electron beam surface remelting has been carried out on AISI D2 cold-worked die steel. The microstructure and hardening behavior of the electron beam surface remelted AISI D2 cold-worked die steel have been studied by means of optical microscopy and Vickers hardness testing. It was found that AISI D2 steel can be successfully surface hardened by electron beam surface remelting. This surface hardening effect can be attributed to microstructural refinement following electron beam surface remelting. (C) 2002 Elsevier Science B.V. All rights reserved.

Electron Beam Surface Treatment. Part II: Microstructure Evolution of Stainless Steel and Aluminum Alloy During Electron Beam Rapid Solidification

Surface rapid solidification microstructures of AISI 321 austenitic stainless steel and 2024 aluminum alloy have been investigated by electron beam remelting process and optical microscopy observation. It is indicated that the morphologies of the melted layer of both stainless steel and aluminum alloy change dramatically compared to the original materials. Also, the microstructures were greatly refined after the electron beam irradiation.