Equalização neural aplicada a sistemas com modulação bidimensional em fibra óptica

Nowadays, optic fiber is one of the most used communication methods, mainly due to the fact that the data transmission rates of those systems exceed all of the other means of digital communication. Despite the great advantage, there are problems that prevent full utilization of the optical channel: by increasing the transmission speed and the distances involved, the data is subjected to non-linear inter symbolic interference caused by the dispersion phenomena in the fiber. Adaptive equalizers can be used to solve this problem, they compensate non-ideal responses of the channel in order to restore the signal that was transmitted. This work proposes an equalizer based on artificial neural networks and evaluates its performance in optical communication systems. The proposal is validated through a simulated optic channel and the comparison with other adaptive equalization techniques

Increased B chromosome frequency and absence of drive in the fish Prochilodus lineatus

The neotropical freshwater fish species Prochilodus lineatus (Pisces, Prochilodontidae) shows 2n = 54 chromosomes plus supernumerary microchromosomes ranging in number from zero to seven among different animals. The transmission rates of B chromosomes were studied by the analysis of the parental and F1 generations in 10 controlled crosses performed with specimens from a natural population. The mean transmission rate observed for B chromosomes (k(B) = 0.511) was consistent with that expected from a regular meiotic behaviour orbs in both sexes and with the theoretical value under a Mendelian mode of transmission (0.5). Possible explanations for the dramatic increase in B frequency observed in this population during the last 10 years are discussed, bearing in mind the current absence of drive.

Using serial bluetooth converters as a sensor link in networked control systems

Networked control systems (NCS) are distributed control system in which sensors, actuators and controllers are physically separated and connected through communication networks. NCS represent the evolution of networked control architectures providing greater modularity and control decentralization, ease maintenance and diagnosis and lower cost of implementation. A recent trend in this research topic is the development of NCS using wireless networks which enable interoperability between existing wired and wireless systems. This paper presents the feasibility analysis of using a serial RS-232 to Bluetooth converter as a wireless sensor link in NCS. In order to support this investigation, relevant performance metrics for wireless control applications such as jitter, time delay and messages lost are highlighted and calculated to evaluate the converter capabilities. In addition the control performance of an implemented motor control system using the converter is analyzed. Experimental results led to the conclusion that serial RS-232 Bluetooth converters can be used to implement wireless networked control systems (WNCS) providing transmission rates and closed control loop times which are acceptable for NCS applications. © 2011 IEEE.

Uma abordagem probabilística do número de reprodução básica em modelos epidemiológicos com aplicação na ferrugem do eucalipto

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Camada de gerenciamento para comunicação entre computadores baseada em redes sem fio (WSE-OS)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Perfil terapêutico assistencial da sífilis congênita no Distrito Federal no ano de 2008

Pós-graduação em Ginecologia, Obstetrícia e Mastologia - FMB

Planejamento de redes de comunicação sem fio para ambiente indoor considerando os efeitos da polarização das antenas: abordagem baseada em medições

Uma das principais aplicações de ondas eletromagnéticas, na atualidade, na área de telecomunicações trata dos enlaces em sistemas móveis sem fio. Sejam estes terrestres (indoor/outdoor) ou via satélites, o projetista do sistema de telecomunicações tem que ser capaz de determinar os sistemas irradiantes, as potências envolvidas, a frequência de operação do sistema, a área de cobertura e os parâmetros de qualidade do serviço. O planejamento das novas redes de comunicações sem fio representa um grande desafio ao incluir serviços cada vez mais avançados com diferentes requisitos de qualidade, suporte a mobilidade, altas taxas de transmissão e capacidades elevadas de tráfego. Os diversos ambientes nos quais essas redes operam, os fenômenos associados produzem diversos efeitos no comportamento do sinal recebido e, consequentemente, uma variação no desempenho do enlace de comunicação entre os pontos de acesso, a rede e os usuários. Por conseguinte, esses efeitos devem ser avaliados corretamente, de tal forma que o dimensionamento da rede atenda aos requisitos de qualidade regulamentados. O presente trabalho objetiva estabelecer uma metodologia para o planejamento de redes de comunicação sem fio para ambientes indoor, considerando os parâmetros de qualidade de serviços e os efeitos da polarização das antenas. Foi proposto um modelo empírico para determinar a área de cobertura desse ambiente a partir de uma abordagem baseada em medições. Como resultado de campanhas de medições, foram identificados os principais parâmetros que interferem nas perdas no enlace de propagação, destacando-se os materiais envolvidos no ambiente bem como os efeitos da polarização das antenas transmissora, entre outros. Tais efeitos, avaliados corretamente, permitirão ao projetista da rede, de uma forma crítica e com base em dados obtidos em campo, definir a melhor configuração de parâmetros e critérios de projeto para a implantação de uma rede móvel de acesso sem fio. As medições para determinação dos parâmetros de cobertura e de qualidade de serviços foram realizadas no prédio do Laboratório de Engenharia Elétrica e de Computação e no prédio de aulas do Instituto de Tecnologia da Universidade Federal do Pará. Nas campanhas de medição foram utilizadas algumas frequências, escolhidas devido à importância dos serviços disponibilizados: 2,4 GHz - redes locais sem fio (WLAN’s); 3,5 GHz - Wimax licenciado; 5,85 GHz - Wimax livre e 10 GHz (a faixa de 9,8 a 10 GHz não está ainda regulamentada, de 10 - 10,15 GHz-radioamador (Resolução Anatel, Nº 452/2006 - D.O.U. de 20.12.2006) ou serviços de comunicações multimídias (SCM) para sistemas em banda larga). Os principais resultados obtidos com o modelo proposto foram avaliados e comparados com os principais modelos da literatura e mostraram que a metodologia adotada para o planejamento de redes de comunicação sem fio em ambientes indoor teve um bom desempenho.

Medidas para caracterização de crosstalk e ruído impulsivo em sistemas DSL

O presente trabalho apresenta testes e experimentos laboratoriais para medição de crosstalk e ruído impulsivo em sistemas DSL, os quais são de grande importância para o aperfeiçoamento e evolução deste tipo de tecnologia. O estudo do crosstalk voltou-se a uma campanha de medições em cabos telefônicos reais de curto comprimento e operando em altas frequências. Os resultados destas medidas foram utilizados no cálculo da capacidade de transmissão de sistemas DSL operando neste cenário ainda pouco explorado. O estudo do ruído impulsivo foi focado no desenvolvimento de um sistema digitalizador de sinais de linha telefônica possibilitando a medição real deste tipo de fenômeno.

Modelo de simulação NS-2 para o protocolo DNP3 sobre o protocolo de rede sem fio IEEE 802.15.4 para simulação de baixo custo de aplicação smart grid

Pós-graduação em Engenharia Elétrica - FEIS

Leveraging wireless devices for networked control systems in industrial applications

Networked control systems (NCSs) are distributed control system in which sensors, actuators and controllers are physically separated and connected through communication networks. NCS represent the evolution of networked control architectures providing greater modularity and control decentralization, ease maintenance and diagnosis and lower cost of implementation. A recent trend in this research topic is the development of NCS using wireless networks(WNCS)which enable interoperability between existing wiredand wireless systems. This paper presents the feasibility analysis of using serial to wireless converter as a wireless sensor link in NCS. In order to support this investigation, relevant performance metrics for wireless control applications such as jitter, time delay and messages lost are highlighted and calculated to evaluate the wireless converter capabilities. In addition the control performance of an implemented motor control system using the converter is analyzed. Experimental results led to the conclusion that serial ZigBee device isrecommended against the Bluetooth as it provided better metrics for control applications. However, bothdevices can be used to implement WNCS providing transmission rates and closed control loop times which are acceptable for NCS applications.Moreoverthe use of thewireless device delay in the PID controller discretization can improve the control performance of the system.

Investigating Avian Influenza Infection Hotspots in Old-World Shorebirds

Heterogeneity in the transmission rates of pathogens across hosts or environments may produce disease hotspots, which are defined as specific sites, times or species associations in which the infection rate is consistently elevated. Hotspots for avian influenza virus (AIV) in wild birds are largely unstudied and poorly understood. A striking feature is the existence of a unique but consistent AIV hotspot in shorebirds (Charadriiformes) associated with a single species at a specific location and time (ruddy turnstone Arenaria interpres at Delaware Bay, USA, in May). This unique case, though a valuable reference, limits our capacity to explore and understand the general properties of AIV hotspots in shorebirds. Unfortunately, relatively few shorebirds have been sampled outside Delaware Bay and they belong to only a few shorebird families; there also has been a lack of consistent oropharyngeal sampling as a complement to cloacal sampling. In this study we looked for AIV hotspots associated with other shorebird species and/or with some of the larger congregation sites of shorebirds in the old world. We assembled and analysed a regionally extensive dataset of AIV prevalence from 69 shorebird species sampled in 25 countries across Africa and Western Eurasia. Despite this diverse and extensive coverage we did not detect any new shorebird AIV hotspots. Neither large shorebird congregation sites nor the ruddy turnstone were consistently associated with AIV hotspots. We did, however, find a low but widespread circulation of AIV in shorebirds that contrast with the absence of AIV previously reported in shorebirds in Europe. A very high AIV antibody prevalence coupled to a low infection rate was found in both first-year and adult birds of two migratory sandpiper species, suggesting the potential existence of an AIV hotspot along their migratory flyway that is yet to be discovered.

Populationsdynamik des Cydia pomonella Granulovirus

Das Cydia pomonella Granulovirus (CpGV, Fam. Baculoviridae) ist ein sehr virulentes und hoch spezifisches Pathogen des Apfelwicklers (Cydia pomonella), das seit mehreren Jahren in der Bundesrepublik Deutschland und anderen Ländern der EU als Insektizid zugelassen ist. Wie andere Baculoviren auch befällt es die Larven der Insekten und ist aufgrund seiner Selektivität für Nicht-Zielorganismen unbedenklich. In der Vergangenheit konzentrierte sich die Erforschung des CpGV auf Bereiche, die für die Anwendung im Pflanzenschutz relevant waren, wobei nach fast 20 Jahren nach der ersten Zulassung noch immer nicht bekannt ist, ob und wie sich das CpGV in der Umwelt etablieren kann. Im Rahmen der vorliegenden Arbeit wurden verschiedene Parameter, mit deren Hilfe die Populationsdynamik des CpGV beschrieben werden kann, analysiert und quantitativ bestimmt. Neben den biologischen Eigenschaften wie Virulenz, DNA-Charakterisierung und Quantifizierung der Virusnachkommenschaft wurden insbesondere die horizontale sowie die vertikale Transmission, die Inaktivierung und die Infektion später Larvenstadien untersucht. Letztlich wurden die ermittelten Parameter zusammen mit Daten aus der Literatur in ein mathematisches Modell integriert. Um die Wahrscheinlichkeit der horizontalen Transmission zu quantifizieren, wurde ein Modellsystem mit losen Äpfeln etabliert, in dem verschiedene Szenarien möglicher horizontaler Transmission unter definierten Laborbedingungen getestet wurden. In Versuchsserien, in denen ein Virusfleck, entsprechend der produzierten Virusmenge einer Eilarve, auf einen Apfel appliziert worden war, war unter den aufgesetzten Apfelwicklerlarven lediglich eine sehr geringe Mortalität von 3 - 6% zu beobachten. Wurde jedoch ein an einer Virusinfektion gestorbener Larvenkadaver als Inokulum verwendet, lag die Mortalitätsrate aufgesetzter Larven bei über 40%. Diese beobachtete hohe horizontale Transmissionsrate konnte mit dem Verhalten der Larven erklärt werden. Die Larven zeigten eine deutliche Einbohrpräferenz für den Stielansatz bzw. den Kelch, wodurch die Wahrscheinlichkeit des Zusammentreffens einer an der Infektion verendeten Larve mit einer gesunden Larve um ein Vielfaches zunahm. In einem ähnlich angelegten Freilandversuch konnte eine horizontale Transmission nicht belegt werden. Der Unterschied zur Kontrollgruppe fiel aufgrund einer hohen natürlichen Mortalität und einer damit einhergehenden niedrigen Dichte der Larven zu gering aus. Parallel hierzu wurde außerdem eine Halbwertszeit von 52 Sonnenstunden für das CpGV ermittelt. Weiterhin konnte festgestellt werden, dass die Mortalität von späteren Larvenstadien, die 14 Tage Zeit hatten sich in die Äpfel einzubohren, bevor eine CpGV-Applikation durchgeführt wurde, ebenso hoch war wie bei Larven, die sich im L1-Stadium auf der Apfeloberfläche infizierten. Aufgrund des höheren Alters jener Larven war der Fraßschaden an befallenen Äpfeln jedoch wesentlich größer und vergleichbar mit dem Fraßschaden einer unbehandelten Kontrolle. Der Versuch zur vertikalen Transmission zeigte dass, obwohl die verwendete Apfelwicklerzucht nicht frei von CpGV war, die Mortalitätsrate der Nachkommen subletal infizierter Weibchen (44%) jedoch deutlich höher war als die der Nachkommen subletal infizierter Männchen (28%) und der unbehandelten Kontrolle (27%). Auch in den PCR-Analysen konnte eine größere Menge an CpGV-Trägern bei den Nachkommen subletal infizierter Weibchen (67%) als bei den Nachkommen subletal infizierter Männchen (49%) und bei der Kontrolle (42%) nachgewiesen werden. Die Ergebnisse deuten darauf hin, dass eine Infektion durch subletal infizierte Weibchen vertikal in die nächste Generation übertragen werden kann. Dies lässt erkennen, dass in der Folgegeneration des Apfelwicklers eine zusätzliche Wirkung des CpGV durch vertikale Transmission auftreten kann. Hierin wäre auch ein potentieller Mechanismus für eine dauerhafte Etablierung des Virus zu sehen. Letztlich wurden alle Parameter, die die CpGV-Apfelwickler-Beziehung beschreiben, in ein mathematisches Modell GRANULO integriert. Nach einer Sensitivitätsanalyse wurde GRANULO teilweise mit Daten aus den Freilandversuchen verifiziert. Durch Modifikation der Virusparameter im Modell konnte anschließend der Einfluss veränderter biologischer Eigenschaften (UV-Stabilität und Transmissionsraten) der Viren in Simulationen theoretisch erprobt werden. Das beschriebene Modell, das allerdings noch einer weitergehenden Verifizierung und Validierung bedarf, ist eine erste Annäherung an die quantitative Erfassung und Modellierung der Populationsdynamik des Systems CpGV-Apfelwickler. Die im Zusammenhang mit der Populationsdynamik des Apfelwicklers erhobenen Daten können einen wertvollen Beitrag zur Optimierung von Kontrollstrategien des Apfelwicklers mittels CpGV leisten. Außerdem geben sie Aufschluss über die Etablierungsmöglichkeiten dieses Bioinsektizids.

[Antiretroviral therapy and pregnancy]

Whereas the perinatal transmission rate with untreated HIV positive women is around 30%, the results of Pediatric AIDS Clinical Trials Group in 1994 showed a reduction by nearly 70% with Zidovudin chemoprophylaxis. The transmission rate can even be reduced to under 2%, if a cesarean section before onset of labour and before premature rupture of membranes is done in addition. An individualized, optimal antiretroviral combination therapy, ideally introduced in the second trimenon (in special cases even already in the first trimenon), is of great importance. As a further strategy of prevention of perinatal transmission, intravenous Zidovudin chemoprophylaxis should be given in addition to the mother during labour and to the newborn during the first six weeks of life. Besides very few exceptions, long-term data after intrauterine administration of antiretroviral therapy do not show any teratogen or other long term consequences to date. The situation in developing countries is very critical with still high transmission rates because of the lack of antiretroviral therapy due to logistical reasons and costs and the need of breastfeeding. For these reasons, more and more feasible short protocols are developed with at least fifty percent reduction of neonatal transmission rates.

Evaluation of control and surveillance strategies for classical swine fever using a simulation model

Classical swine fever (CSF) outbreaks can cause enormous losses in naïve pig populations. How to best minimize the economic damage and number of culled animals caused by CSF is therefore an important research area. The baseline CSF control strategy in the European Union and Switzerland consists of culling all animals in infected herds, movement restrictions for animals, material and people within a given distance to the infected herd and epidemiological tracing of transmission contacts. Additional disease control measures such as pre-emptive culling or vaccination have been recommended based on the results from several simulation models; however, these models were parameterized for areas with high animal densities. The objective of this study was to explore whether pre-emptive culling and emergency vaccination should also be recommended in low- to moderate-density areas such as Switzerland. Additionally, we studied the influence of initial outbreak conditions on outbreak severity to improve the efficiency of disease prevention and surveillance. A spatial, stochastic, individual-animal-based simulation model using all registered Swiss pig premises in 2009 (n=9770) was implemented to quantify these relationships. The model simulates within-herd and between-herd transmission (direct and indirect contacts and local area spread). By varying the four parameters (a) control measures, (b) index herd type (breeding, fattening, weaning or mixed herd), (c) detection delay for secondary cases during an outbreak and (d) contact tracing probability, 112 distinct scenarios were simulated. To assess the impact of scenarios on outbreak severity, daily transmission rates were compared between scenarios. Compared with the baseline strategy (stamping out and movement restrictions) vaccination and pre-emptive culling neither reduced outbreak size nor duration. Outbreaks starting in a herd with weaning piglets or fattening pigs caused higher losses regarding to the number of culled premises and were longer lasting than those starting in the two other index herd types. Similarly, larger transmission rates were estimated for these index herd type outbreaks. A longer detection delay resulted in more culled premises and longer duration and better transmission tracing increased the number of short outbreaks. Based on the simulation results, baseline control strategies seem sufficient to control CSF in low-medium animal-dense areas. Early detection of outbreaks is crucial and risk-based surveillance should be focused on weaning piglet and fattening pig premises.

WiMAX,Technology and Market.

Wireless communication is the transfer of information from one place to another without using wires. From the earliest times, humans have felt the need to develop techniques of remote communication. From this need arose the smoke signals, communication by sun reflection in mirrors and so on. But today the telecommunications electronic devices such as telephone, television, radio or computer. Radio and television are used for one-way communication. Telephone and computer are used for two-way communication. In wireless networks there is almost unlimited mobility, we can access the network almost anywhere or anytime. In wired networks we have the restriction of using the services in fixed area services. The demand of the wireless is increasing very fast; everybody wants broadband services anywhere anytime. WiMAX (Worldwide Interoperability for Microwave Access) is a broadband wireless technology based on IEEE 802.16-2004 and IEEE 802.16e-2005 that appears to solve this demand. WIMAX is a system that allows wireless data transmission in areas of up to 48 km of radius. It is designed as a wireless alternative to ADSL and a way to connect nodes in wireless metropolitan areas network. Unlike wireless systems that are limited in most cases, about 100 meter, providing greater coverage and more bandwidth. WIMAX promises to achieve high data transmission rates over large areas with a great amount of users. This alternative to the networks of broadband access common as DSL o Wi-Fi, can give broadband access to places quickly to rural areas and developing areas around the world. This paper is a study of WIMAX technology and market situation. First, the paper is responsible for explaining the technical aspects of WIMAX. For this gives an overview of WIMAX standards, physical layer, MAC layer and WiMAX, Technology and Market Beijing University of Post and Telecommunications 2 WIMAX network architecture. Second, the paper address the issue of market in which provides an overview of development and deployment of WIMAX to end the future development trend of WIMAX is addressed. RESUMEN: Por comunicaciones inalámbricas se entiende la transferencia de información desde un lugar a otro sin la necesidad de un soporte físico como es por ejemplo el cable. Por lo que remontándose a los principios de la existencia del ser humano, nos damos cuenta de que el ser humano siempre ha sentido la necesidad de desarrollar técnicas para lograr comunicarse a distancia con sus semejantes. De dicha necesidad, surgieron técnicas tan ancestrales como puede ser la comunicación mediante señales de humo o por reflexión de los rayos solares en espejos entre otras. La curiosidad del ser humano y la necesidad de comunicarse a distancia fue la que llevó a Alexander Graham Bell a inventar el teléfono en 1876. La aparición de un dispositivo que permitía comunicarse a distancia permitiendo escuchar la voz de aquella persona con la que se quería hablar, supuso una revolución no solo en el panorama tecnológico, si no también en el panorama social. Pues a parte de permitir comunicaciones a larga distancia, solventó el problema de la comunicación en “tiempo real”. A raíz de este invento, la tecnología en materia de comunicación ha ido avanzando significativamente, más concretamente en lo referido a las comunicaciones inalámbricas. En 1973 se realizó la primera llamada desde un terminal móvil aunque no fue hasta 1983 cuando se empezó a comercializar dicho terminal, lo que supuso un cambio de hábitos y costumbres para la sociedad. Desde la aparición del primer móvil el crecimiento del mercado ha sido exponencial, lo que ha repercutido en una demanda impensable de nuevas aplicaciones integradas en dichos dispositivos móviles que satisfagan las necesidades que día a día autogenera la sociedad. Tras conseguir realizar llamadas a larga distancia de forma inalámbrica, el siguiente paso fue la creación de los SMS (Short Message System) lo que supuso una nueva revolución además de abaratar costes al usuario a la hora de comunicarse. Pero el gran reto para la industria de las comunicaciones móviles surgió con la aparición de internet. Todo el mundo sentía la necesidad de poder conectarse a esa gran base de datos que es internet en cualquier parte y en cualquier momento. Las primeras conexiones a internet desde dispositivos móviles se realizaron a través de la tecnología WAP (Wireless Application Protocol) hasta la aparición de la tecnología GPRS que permitía la conexión mediante protocolo TCP/IP. A partir de estas conexiones han surgido otras tecnologías, como EDGE, HSDPA, etc., que permitían y permiten la conexión a internet desde dispositivos móviles. Hoy en día la demanda de servicios de red inalámbrica crece de forma rápida y exponencial, todo el mundo quiere servicios de banda ancha en cualquier lugar y en cualquier momento. En este documento se analiza la tecnología WiMAX ( Worldwide Interoperability for Microwave Access) que es una tecnología de banda ancha basada en el estándar IEEE 802.16 creada para brindar servicios a la demanda emergente en la banda ancha desde un punto de vista tecnológico, donde se da una visión de la parte técnica de la tecnología; y desde el punto de vista del mercado, donde se analiza el despliegue y desarrollo de la tecnología desde el punto de vista de negocio. WiMAX es una tecnología que permite la transmisión inalámbrica de datos en áreas de hasta 48Km de radio y que está diseñada como alternativa inalámbrica para ADSL y para conectar nodos de red inalámbrica en áreas metropolitanas. A diferencia de los sistemas inalámbricos existentes que están limitados en su mayoría a unos cientos de metros, WiMAX ofrece una mayor cobertura y un mayor ancho de banda que permita dar soporte a nuevas aplicaciones, además de alcanzar altas tasas de transmisión de datos en grandes áreas con una gran cantidad de usuarios. Se trata de una alternativa a las redes de acceso de banda ancha como DSL o Wi-Fi, que puede dar acceso de banda ancha a lugares tales como zonas rurales o zonas en vías de desarrollo por todo el mundo con rapidez. Existen dos tecnologías de WiMAX, WiMAX fijo (basado en el estándar IEEE 802.16d-2004) y WiMAX móvil (basado en el estándar IEEE 802.16e-2005). La tecnología fija está diseñada para comunicaciones punto a multipunto, mientras que la fija lo está para comunicaciones multipunto a multipunto. WiMAX móvil se basa en la tecnología OFDM que ofrece ventajas en términos de latencia, eficiencia en el uso del espectro y soporte avanzado para antenas. La modulación OFDM es muy robusta frente al multitrayecto, que es muy habitual en los canales de radiodifusión, frente al desvanecimiento debido a las condiciones meteorológicas y frente a las interferencias de RF. Una vez creada la tecnología WiMAX, poseedora de las características idóneas para solventar la demanda del mercado, ha de darse el siguiente paso, hay que convencer a la industria de las telecomunicaciones de que dicha tecnología realmente es la solución para que apoyen su implantación en el mercado de la banda ancha para las redes inalámbricas. Es aquí donde entra en juego el estudio del mercado que se realiza en este documento. WiMAX se enfrenta a un mercado exigente en el que a parte de tener que dar soporte a la demanda técnica, ha de ofrecer una rentabilidad económica a la industria de las comunicaciones móviles y más concretamente a las operadoras móviles que son quienes dentro del sector de las telecomunicaciones finalmente han de confiar en la tecnología para dar soporte a sus usuarios ya que estos al fin y al cabo lo único que quieren es que su dispositivo móvil satisfaga sus necesidades independientemente de la tecnología que utilicen para tener acceso a la red inalámbrica de banda ancha. Quizás el mayor problema al que se ha enfrentado WiMAX haya sido la situación económica en la que se encuentra el mundo. WiMAX a comenzado su andadura en uno de los peores momentos, pero aun así se presenta como una tecnología capaz de ayudar al mundo a salir hacia delante en estos tiempos tan duros. Finalmente se analiza uno de los debates existentes hoy en día en el sector de las comunicaciones móviles, WiMAX vs. LTE. Como se puede observar en el documento realmente una tecnología no saldrá victoriosa frente a la otra, si no que ambas tecnologías podrán coexistir y trabajar de forma conjunta.