Análise do comportamento de estacas do tipo broca escavada com trado mecânico, solicitadas por esforços transversais

Pós-graduação em Engenharia Civil - FEIS

Utilização de reforço geossintético em vias ferroviárias

This report analyses the use of geosynthetics in railways for subgrade reinforcement and separation of the track layers. Cases of instrumented test sections were studied. These test sections were located in Australia (with geocomposite applications), Brazil (with geotextile and geodrid applications) and China (with geotextile and geodrid applications). Railway design methods using geosynthetics applications were analyzed as well. Based on a studied case for implementation of geosynthetics in a German railway, a railway track was simulated with and without the use of geosynthetics, respectively on PLAXIS v.8 and FERROVIA 3.0 softwares. The performance benefits of the geosynthetics applications in railways were, therefore, confirmed, based on the simulation results

Il dimensionamento delle sovrastrutture stradali non pavimentate

A comparison between main design methods for unpaved roads is presented in this paper. An unpaved road is made up of an unbound aggregate base course lying on a usually weak subgrade. A geosynthetic might be put between the two in reinforcing and separating function. The goal of a design method is to find the appropriate thickness of the base course knowing at least traffic volume, wheel load, tire pressure, undrained cohesion of the subgrade, allowable rut depth and influence of the reinforcement. Geosynthetics can reduce the thickness or the quality of aggregate required and improve the durability of an unpaved road. Geotextiles contribute to save aggregate through interaction friction and separation, while geogrids through interlocking between his apertures and lithic base elements. In the last chapter a case study is discussed and design thicknesses with two design methods for the three possible cases (i.e. unreinforced, geotextile reinforced, geogrid reinforced) are calculated.

Simplified longitudinal seismic analysis of buried tunnels

In this paper an analytical static approach to analyse buried tunnels under seismic surface waves (Rayleigh and Love waves), propagating parallel to the tunnels axis, is provided. In the proposed method, the tunnel is considered as a beam on elastic foundation by using a Winkler model to represent the subgrade reaction and the soil-structure interaction. The seismic load is imposed by giving at the base of the soil springs a determined configuration corresponding to the free-field motion. From the solution of the differential governing equations of the problem, results are obtained in form of relative displacements between points of tunnel, and therefore the seismic bending moments and shearing forces, acting on the tunnel cross section, can be computed.

Sobre el comportamiento de micropilotes trabajando a flexión y/o cortante en estructuras de tierra

El empleo de los micropilotes en la ingeniería civil ha revolucionado las técnicas de estabilización de terraplenes a media ladera, ya que aunque los pilotes pueden ser la opción más económica, el uso de micropilotes permite llegar a sitios inaccesibles con menor coste de movimientos de tierras, realización de plataformas de trabajo de dimensiones reducidas, maquinaria necesaria es mucho más pequeña, liviana y versátil en su uso, incluyendo la posibilidad de situar la fabricación de morteros o lechadas a distancias de varias decenas de metros del elemento a ejecutar. Sin embargo, realizando una revisión de la documentación técnica que se tiene en el ámbito ingenieril, se comprobó que los sistemas de diseño de algunos casos (micropilotes en terraplenes a media ladera, micropilotes en pantallas verticales, micropilotes como “paraguas” en túneles, etc.) eran bastante deficientes o poco desarrollados. Premisa que permite concluir que el constructor ha ido por delante (como suele ocurrir en ingeniería geotécnica) del cálculo o de su análisis teórico. Del mismo modo se determinó que en su mayoría los micropilotes se utilizan en labores de recalce o como nueva solución de cimentación en condiciones de difícil acceso, casos en los que el diseño de los micropilotes viene definido por cargas axiales, de compresión o de tracción, consideraciones que se contemplan en reglamentaciones como la “Guía para el proyecto y la ejecución de micropilotes en obras de carretera” del Ministerio de Fomento. En los micropilotes utilizados para estabilizar terraplenes a media ladera y micropilotes actuando como muros pantalla, en los que éstos trabajan a esfuerzo cortante y flexión, no se dispone de sistemas de análisis fiables o no se introduce adecuadamente el problema de interacción terreno-micropilote. Además en muchos casos, los parámetros geotécnicos que se utilizan no tienen una base técnico-teórica adecuada por lo que los diseños pueden quedar excesivamente del lado de la seguridad, en la mayoría de los casos, o todo lo contrario. Uno de los objetivos principales de esta investigación es estudiar el comportamiento de los micropilotes que están sometidos a esfuerzos de flexión y cortante, además de otros objetivos de gran importancia que se describen en el apartado correspondiente de esta tesis. Cabe indicar que en este estudio no se ha incluido el caso de micropilotes quasi-horizontales trabajando a flexion (como los “paraguas” en túneles), por considerarse que estos tienen un comportamiento y un cálculo diferente, que está fuera del alcance de esta investigación. Se ha profundizado en el estudio del empleo de micropilotes en taludes, presentando casos reales de obras ejecutadas, datos estadísticos, problemas de diseño y ejecución, métodos de cálculo simplificados y modelación teórica en cada caso, efectuada mediante el empleo de elementos finitos con el Código Plaxis 2D. Para llevar a cabo los objetivos que se buscan con esta investigación, se ha iniciado con el desarrollo del “Estado del Arte” que ha permitido establecer tipología, aplicaciones, características y cálculo de los micropilotes que se emplean habitualmente. Seguidamente y a efectos de estudiar el problema dentro de un marco geotécnico real, se ha seleccionado una zona española de actuación, siendo ésta Andalucía, en la que se ha utilizado de manera muy importante la técnica de micropilotes sobre todo en problemas de estabilidad de terraplenes a media ladera. A partir de ahí, se ha realizado un estudio de las propiedades geotécnicas de los materiales (principalmente suelos y rocas muy blandas) que están presentes en esta zona geográfica, estudio que ha sido principalmente bibliográfico o a partir de la experiencia en la zona del Director de esta tesis. Del análisis realizado se han establecido ordenes de magnitud de los parámetros geotécnicos, principalmente la cohesión y el ángulo de rozamiento interno (además del módulo de deformación aparente o de un módulo de reacción lateral equivalente) para los diversos terrenos andaluces. Con el objeto de conocer el efecto de la ejecución de un micropilote en el terreno (volumen medio real del micropilote, una vez ejecutado; efecto de la presión aplicada en las propiedades del suelo circundante, etc.) se ha realizado una encuesta entre diversas empresas españolas especializadas en la técnica de los micropilotes, a efectos de controlar los volúmenes de inyección y las presiones aplicadas, en función de la deformabilidad del terreno circundante a dichos micropilotes, con lo que se ha logrado definir una rigidez a flexión equivalente de los mismos y la definición y características de una corona de terreno “mejorado” lograda mediante la introducción de la lechada y el efecto de la presión alrededor del micropilote. Con las premisas anteriores y a partir de los parámetros geotécnicos determinados para los terrenos andaluces, se ha procedido a estudiar la estabilidad de terraplenes apoyados sobre taludes a media ladera, mediante el uso de elementos finitos con el Código Plaxis 2D. En el capítulo 5. “Simulación del comportamiento de micropilotes estabilizando terraplenes”, se han desarrollado diversas simulaciones. Para empezar se simplificó el problema simulando casos similares a algunos reales en los que se conocía que los terraplenes habían llegado hasta su situación límite (de los que se disponía información de movimientos medidos con inclinómetros), a partir de ahí se inició la simulación de la inestabilidad para establecer el valor de los parámetros de resistencia al corte del terreno (mediante un análisis retrospectivo – back-análisis) comprobando a su vez que estos valores eran similares a los deducidos del estudio bibliográfico. Seguidamente se han introducido los micropilotes en el borde de la carretera y se ha analizado el comportamiento de éstos y del talud del terraplén (una vez construidos los micropilotes), con el objeto de establecer las bases para su diseño. De este modo y adoptando los distintos parámetros geotécnicos establecidos para los terrenos andaluces, se simularon tres casos reales (en Granada, Málaga y Ceuta), comparando los resultados de dichas simulaciones numéricas con los resultados de medidas reales de campo (desplazamientos del terreno, medidos con inclinómetros), obteniéndose una reproducción bastante acorde a los movimientos registrados. Con las primeras simulaciones se concluye que al instalar los micropilotes la zona más insegura de la ladera es la de aguas abajo. La superficie de rotura ya no afecta a la calzada que protegen los micropilotes. De ahí que se deduzca que esta solución sea válida y se haya aplicado masivamente en Andalucía. En esas condiciones, podría decirse que no se está simulando adecuadamente el trabajo de flexión de los micropilotes (en la superficie de rotura, ya que no les corta), aunque se utilicen elementos viga. Por esta razón se ha realizado otra simulación, basada en las siguientes hipótesis: − Se desprecia totalmente la masa potencialmente deslizante, es decir, la que está por delante de la fila exterior de micros. − La estratigrafía del terreno es similar a la considerada en las primeras simulaciones. − La barrera de micropilotes está constituida por dos elementos inclinados (uno hacia dentro del terraplén y otro hacia fuera), con inclinación 1(H):3(V). − Se puede introducir la rigidez del encepado. − Los micros están separados 0,556 m ó 1,00 m dentro de la misma alineación. − El empotramiento de los micropilotes en el sustrato resistente puede ser entre 1,5 y 7,0 m. Al “anular” el terreno que está por delante de los micropilotes, a lo largo del talud, estos elementos empiezan claramente a trabajar, pudiendo deducirse los esfuerzos de cortante y de flexión que puedan actuar sobre ellos (cota superior pero prácticamente muy cerca de la solución real). En esta nueva modelación se ha considerado tanto la rigidez equivalente (coeficiente ϴ) como la corona de terreno tratado concéntrico al micropilote. De acuerdo a esto último, y gracias a la comparación de estas modelaciones con valores reales de movimientos en laderas instrumentadas con problemas de estabilidad, se ha verificado que existe una similitud bastante importante entre los valores teóricos obtenidos y los medidos en campo, en relación al comportamiento de los micropilotes ejecutados en terraplenes a media ladera. Finalmente para completar el análisis de los micropilotes trabajando a flexión, se ha estudiado el caso de micropilotes dispuestos verticalmente, trabajando como pantallas discontinuas provistas de anclajes, aplicado a un caso real en la ciudad de Granada, en la obra “Hospital de Nuestra Señora de la Salud”. Para su análisis se utilizó el código numérico CYPE, basado en que la reacción del terreno se simula con muelles de rigidez Kh o “módulo de balasto” horizontal, introduciendo en la modelación como variables: a) Las diferentes medidas obtenidas en campo; b) El espesor de terreno cuaternario, que por lo que se pudo determinar, era variable, c) La rigidez y tensión inicial de los anclajes. d) La rigidez del terreno a través de valores relativos de Kh, recopilados en el estudio de los suelos de Andalucía, concretamente en la zona de Granada. Dicha pantalla se instrumentó con 4 inclinómetros (introducidos en los tubos de armadura de cuatro micropilotes), a efectos de controlar los desplazamientos horizontales del muro de contención durante las excavaciones pertinentes, a efectos de comprobar la seguridad del conjunto. A partir del modelo de cálculo desarrollado, se ha comprobado que el valor de Kh pierde importancia debido al gran número de niveles de anclajes, en lo concerniente a las deformaciones horizontales de la pantalla. Por otro lado, los momentos flectores son bastante sensibles a la distancia entre anclajes, al valor de la tensión inicial de los mismos y al valor de Kh. Dicho modelo también ha permitido reproducir de manera fiable los valores de desplazamientos medidos en campo y deducir los parámetros de deformabilidad del terreno, Kh, con valores del orden de la mitad de los medidos en el Metro Ligero de Granada, pero visiblemente superiores a los deducibles de ábacos que permiten obtener Kh para suelos granulares con poca cohesión (gravas y cuaternario superior de Sevilla) como es el caso del ábaco de Arozamena, debido, a nuestro juicio, a la cementación de los materiales presentes en Granada. En definitiva, de las anteriores deducciones se podría pensar en la optimización del diseño de los micropilotes en las obras que se prevean ejecutar en Granada, con similares características al caso de la pantalla vertical arriostrada mediante varios niveles de anclajes y en las que los materiales de emplazamiento tengan un comportamiento geotécnico similar a los estudiados, con el consiguiente ahorro económico. Con todo ello, se considera que se ha hecho una importante aportación para el diseño de futuras obras de micropilotes, trabajando a flexión y cortante, en obras de estabilización de laderas o de excavaciones. Using micropiles in civil engineering has transformed the techniques of stabilization of embankments on the natural or artificial slopes, because although the piles may be the cheapest option, the use of micropiles can reach inaccessible places with lower cost of earthworks, carrying out small work platforms. Machinery used is smaller, lightweight and versatile, including the possibility of manufacturing mortars or cement grouts over distances of several tens of meters of the element to build. However, making a review of the technical documentation available in the engineering field, it was found that systems designed in some cases (micropiles in embankments on the natural slopes, micropiles in vertical cut-off walls, micropiles like "umbrella" in tunnels, etc.) were quite poor or underdeveloped. Premise that concludes the builder has gone ahead (as usually happen in geotechnical engineering) of calculation or theoretical analysis. In the same way it was determined that most of the micropiles are used in underpinning works or as a new foundation solution in conditions of difficult access, in which case the design of micropiles is defined by axial, compressive or tensile loads, considered in regulations as the " Handbook for the design and execution of micropiles in road construction" of the Ministry of Development. The micropiles used to stabilize embankments on the slopes and micropiles act as retaining walls, where they work under shear stress and bending moment, there are not neither reliable systems analysis nor the problem of soil-micropile interaction are properly introduced. Moreover, in many cases, the geotechnical parameters used do not have a proper technical and theoretical basis for what designs may be excessively safe, or the opposite, in most cases. One of the main objectives of this research is to study the behavior of micro piles which are subjected to bending moment and shear stress, as well as other important objectives described in the pertinent section of this thesis. It should be noted that this study has not included the case of quasi-horizontal micropiles working bending moment (as the "umbrella" in tunnels), because it is considered they have a different behavior and calculation, which is outside the scope of this research. It has gone in depth in the study of using micropiles on slopes, presenting real cases of works made, statistics, problems of design and implementation, simplified calculation methods and theoretical modeling in each case, carried out by using FEM (Finite Element Method) Code Plaxis 2D. To accomplish the objectives of this research, It has been started with the development of the "state of the art" which stipulate types, applications, characteristics and calculation of micropiles that are commonly used. In order to study the problem in a real geotechnical field, it has been selected a Spanish zone of action, this being Andalusia, in which it has been used in a very important way, the technique of micropiles especially in embankments stability on natural slopes. From there, it has made a study of the geotechnical properties of the materials (mainly very soft soils and rocks) that are found in this geographical area, which has been mainly a bibliographic study or from the experience in the area of the Director of this thesis. It has been set orders of magnitude of the geotechnical parameters from analyzing made, especially the cohesion and angle of internal friction (also apparent deformation module or a side reaction module equivalent) for various typical Andalusian ground. In order to determine the effect of the implementation of a micropile on the ground (real average volume of micropile once carried out, effect of the pressure applied on the properties of the surrounding soil, etc.) it has conducted a survey among various skilled companies in the technique of micropiles, in order to control injection volumes and pressures applied, depending on the deformability of surrounding terrain such micropiles, whereby it has been possible to define a bending stiffness and the definition and characteristics of a crown land "improved" achieved by introducing the slurry and the effect of the pressure around the micropile. With the previous premises and from the geotechnical parameters determined for the Andalusian terrain, we proceeded to study the stability of embankments resting on batters on the slope, using FEM Code Plaxis 2D. In the fifth chapter "Simulation of the behavior of micropiles stabilizing embankments", there were several different numerical simulations. To begin the problem was simplified simulating similar to some real in which it was known that the embankments had reached their limit situation (for which information of movements measured with inclinometers were available), from there the simulation of instability is initiated to set the value of the shear strength parameters of the ground (by a retrospective analysis or back-analysis) checking these values were similar to those deduced from the bibliographical study Then micropiles have been introduced along the roadside and its behavior was analyzed as well as the slope of embankment (once micropiles were built ), in order to establish the basis for its design. In this way and taking the different geotechnical parameters for the Andalusian terrain, three real cases (in Granada, Malaga and Ceuta) were simulated by comparing the results of these numerical simulations with the results of real field measurements (ground displacements measured with inclinometers), getting quite consistent information according to registered movements. After the first simulations it has been concluded that after installing the micropiles the most insecure area of the natural slope is the downstream. The failure surface no longer affects the road that protects micropiles. Hence it is inferred that this solution is acceptable and it has been massively applied in Andalusia. Under these conditions, one could say that it is not working properly simulating the bending moment of micropiles (on the failure surface, and that does not cut them), although beam elements are used. Therefore another simulation was performed based on the following hypotheses: − The potentially sliding mass is totally neglected, that is, which is ahead of the outer row of micropiles. − Stratigraphy field is similar to the one considered in the first simulations. − Micropiles barrier is constituted by two inclined elements (one inward and one fill out) with inclination 1 (H): 3 (V). − You can enter the stiffness of the pile cap. − The microlies lines are separated 0.556 m or 1.00 m in the same alignment. − The embedding of the micropiles in the tough substrate can be between 1.5 and 7.0 m. To "annul" the ground that is in front of the micro piles, along the slope, these elements clearly start working, efforts can be inferred shear stress and bending moment which may affect them (upper bound but pretty close to the real) solution. In this new modeling it has been considered both equivalent stiffness coefficient (θ) as the treated soil crown concentric to the micropile. According to the latter, and by comparing these values with real modeling movements on field slopes instrumented with stability problems, it was verified that there is quite a significant similarity between the obtained theoretical values and the measured field in relation to the behavior of micropiles executed in embankments along the natural slope. Finally to complete the analysis of micropiles working in bending conditions, we have studied the case of micropiles arranged vertically, working as discontinued cut-off walls including anchors, applied to a real case in the city of Granada, in the play "Hospital of Our Lady of the Health ". CYPE numeric code, based on the reaction of the ground is simulated spring stiffness Kh or "subgrade" horizontal, introduced in modeling was used as variables for analysis: a) The different measurements obtained in field; b) The thickness of quaternary ground, so that could be determined, was variable, c) The stiffness and the prestress of the anchors. d) The stiffness of the ground through relative values of Kh, collected in the study of soils in Andalusia, particularly in the area of Granada. (previously study of the Andalusia soils) This cut-off wall was implemented with 4 inclinometers (introduced in armor tubes four micropiles) in order to control the horizontal displacements of the retaining wall during the relevant excavations, in order to ensure the safety of the whole. From the developed model calculation, it was found that the value of Kh becomes less important because a large number of anchors levels, with regard to the horizontal deformation of the cut-off wall. On the other hand, the bending moments are quite sensitive to the distance between anchors, the initial voltage value thereof and the value of Kh. This model has also been reproduced reliably displacement values measured in the field and deduce parameters terrain deformability, Kh, with values around half the measured Light Rail in Granada, but visibly higher than deductible of abacuses which can obtain Kh for granular soils with low cohesion (upper Quaternary gravels and Sevilla) such as Abacus Arozamena, because, in our view, to cementing materials in Granada. In short, previous deductions you might think on optimizing the design of micropiles in the works that are expected to perform in Granada, with similar characteristics to the case of the vertical cut-off wall braced through several levels of anchors and in which materials location have a geotechnical behavior similar to those studied, with the consequent economic savings. With all this, it is considered that a significant contribution have been made for the design of future works of micropiles, bending moment and shear stress working in slope stabilization works or excavations.

Influencia de la temperatura en la deflexión de firmes flexibles

En esta investigación se ha estudiado el efecto de la variación de la temperatura en la deflexión de firmes flexibles. En primer lugar se han recopilado los criterios existentes de ajuste de la deflexión por efecto de la temperatura. Posteriormente, se ha llevado a cabo un estudio empírico mediante la auscultación de las deflexiones en cinco tramos de carretera con firme flexible y con diferentes espesores de mezclas bituminosas (entre 10 y 30 cm). Las medidas se han efectuado en dos campañas (verano e invierno), tratando de abarcar un amplio rango de temperaturas. En cada campaña, se han llevado a cabo distintas auscultaciones a diferentes temperaturas. Las medidas de cada campaña se han realizado el mismo día. Se han obtenido los coeficientes empíricos de ajuste por temperatura para cada tramo analizado. Además, se ha realizado un estudio teórico mediante la elaboración de diferentes modelos (multicapa elástico lineal, multicapa visco-elástico lineal y elementos finitos) que reproducen la respuesta estructural de los firmes flexibles auscultados. La caracterización mecánica de las mezclas bituminosas se ha realizado mediante ensayos de módulo complejo en laboratorio, a diferentes temperaturas y frecuencias, sobre testigos extraídos en las carreteras estudiadas. Se han calculado los coeficientes teóricos de ajuste por temperatura para cada modelo elaborado y tramo analizado. Finalmente, se ha realizado un estudio comparativo entre los distintos coeficientes de ajuste (existentes, empíricos y teóricos), que ha puesto de manifiesto que, en todos los casos analizados, los coeficientes obtenidos en el modelo de elementos finitos son los que más se aproximan a los coeficientes empíricos (valor de referencia para los tramos analizados). El modelo desarrollado de elementos finitos permite reproducir el comportamiento visco-elástico de las mezclas bituminosas y el carácter dinámico de las cargas aplicadas. Se han utilizado elementos tipo tetraedro isoparamétrico lineal (C3D8R) para el firme y la parte superior del cimiento, mientras que para la parte inferior se han empleado elementos infinitos (CIN3D8). In this research the effect produced by the temperature change on flexible pavements deflection is analysed. First, the existing criteria of deflection adjustment by temperature were collected. Additionally, an empirical analysis was carried out, consisting on deflection tests in five flexible-pavement road sections with different asphalt mix thickness (from 10 to 30 cm). The measures were taken in two seasons (summer and winter) in an effort to register a wide range of temperatures. Different surveys were carried out at different temperatures in each season. The tests of each season were done at the same day. The empirical temperature adjustment factors for every analysed section were obtained. A theoretical study was carried out by developing different models (linear elastic multilayer, linear visco-elastic multilayer and finite elements) that reproduce the structural response of the tested flexible pavements. The mechanical characterization of the asphalt mixes was achieved through laboratory complex-modulus tests at different temperatures and frequencies, using pavement cores from the surveyed roads. The theoretical temperature adjustment factors for each model developed and each section analysed were calculated. Finally, a comparative study among the different adjustment factors (existing, empirical and theoretical) was carried out. It has shown that, in all analysed cases, the factors obtained with the finite elements model are the closest to the empirical factors (reference value for the analysed sections). The finite elements model developed makes it possible to reproduce the visco-elastic behavior of the asphalt mixes and the dynamic nature of the applied loads. Linear isoparametric tetrahedral elements (C3D8R) have been used for the pavement and the subgrade, while infinite elements (CIN3D8) have been used for the foundations.

Análise dos resultados do ensaio CBR realizado em condições variadas de umidade pós-compactação

O objetivo deste trabalho é avaliar a influência da variação do teor de umidade no valor do índice de suporte CBR de uma brita estabilizada granulometricamente e de seis solos coletados em rodovias do interior do Estado de São Paulo. Os seis solos estudados foram divididos em três pares, com curvas granulométricas próximas, mesma classificação HRB e USCS, sendo cada par formado por um solo de comportamento laterítico e um solo de comportamento não-laterítico. Os corpos-de-prova foram moldados na umidade ótima e massa específica seca máxima obtidos com os resultados do ensaio de Proctor normal. Os materiais foram analisados sob quatro condições de umidade: sem imersão, após alcançar metade da umidade de estabilização, após quatro e oito dias de imersão. Observou-se a distribuição da umidade interna dos corpos-de-prova para cada uma das situações. Foi analisada a influência do envelhecimento dos materiais solto e compactado por quatro dias e sem imersão, nos resultados dos ensaios de CBR. Com os resultados pôde-se correlacionar a influência da granulometria e da gênese dos materiais nos resultados dos ensaios de índice de suporte CBR nas diversas condições de umidade avaliadas.

Influência da rigidez vertical no comportamento mecânico e dimensionamento da via permanente ferroviária.

A via permanente representa um elemento imprescindível na composição do transporte ferroviário e seu desempenho deve ser adequado, de forma a garantir tanto segurança quanto conforto. Assim, diversos aspectos devem ser analisados ainda na fase de projeto, através de dimensionamentos que confrontem diferentes parâmetros da resposta da via e os limites estabelecidos. Dessa forma, o conhecimento do comportamento mecânico da via, devido aos esforços impostos pela passagem do material rodante, passa a ser essencial no projeto de uma estrutura que garanta os requisitos necessários, sem ser inviável economicamente. Visto que esse comportamento mecânico é muito sensível à rigidez vertical da estrutura, o presente trabalho apresenta análises da influência desse parâmetro na resposta da via e, consequentemente, no seu dimensionamento. Nesse contexto, o trabalho abrange tanto o caso de vias em lastro solicitadas por trens de carga, quanto o caso de vias em laje solicitadas por trens de passageiros em meios urbanos. No primeiro caso são realizados estudos paramétricos, por meio de modelos clássicos e um modelo mecanicista, para a análise de momentos fletores e deflexões nos trilhos, bem como tensões verticais nas camadas de lastro, sub-lastro e subleito. Já no segundo caso, são realizados estudos paramétricos relativos à transmissibilidade e à atenuação de vibrações causadoras de ruído secundário. Também é feita uma análise da influência da rigidez vertical na amplificação dinâmica das cargas estáticas, que pode ser aplicada a ambos os casos citados e até extrapolada para casos de vias de alta velocidade. Os resultados mostraram que aumentos de rigidez vertical resultam em ganhos do ponto de vista de momentos fletores e deflexões nos trilhos, além de maior resistência e capacidade de dissipação de tensões verticais nas camadas de lastro, sub-lastro e subleito. Por outro lado, esses aumentos também levaram a maiores tensões nas camadas subjacentes à grade citadas, além de atenuações de vibrações em menores intervalos de frequência e maiores amplificações dinâmicas das cargas estáticas em vias de alta velocidade. Assim, é mostrado que a influência da rigidez vertical, tanto da via como um todo quanto de alguns elementos específicos, não deve ser analisada de forma genérica, pois, dependendo do parâmetro da resposta da via considerado no dimensionamento, seu aumento pode representar uma influência positiva ou negativa.

Long Term Pavement Performance computed parameter : frost penetration /

"HRDI-13/11-08(1M)E"--P. 4 of cover.

Utilização do resíduo grosso do beneficiamento da scheelita em aplicações rodoviárias

Mining is an activity of great economic and social value, assisting in the development of the country. However, it can be extremely harmful to the environment if no proper waste management study exists as mitigation measure its effects. Sample some of these harmful effects are pollution: water, through the seepage of waste into the groundwater; soil; of fauna and flora; sound (due to the noise of machines); visual from the residue stored in the open, changing the local landscape; and air. One way to mitigate environmental impacts caused by mining is the proper management of their waste through their use on highways. To that end, this paper proposes to give an appropriate destination to grit coming from the beneficiation of scheelite, due to mining activity from mining group Tomaz Salustino in Brejuí mine, located in the city of Currais Novos in the state of Rio Grande do Norte. This work was developed in four stages. The first comprised the chemical and mineralogical tests, DRX and FRX in which they sought to discover the composition of the material studied. The next step involved the physical characteristics of the waste by means of specific tests and grinding the solid mass, LL and LP. The third stage included the specific tests applied to the pavement, with the compaction test and test Index Support California. Finally, the fourth stage was the mechanical characterization, represented by direct shear tests, both in the flooded condition and not in flooded condition. The technical feasibility of using the modified energie compacted in layers of subbase power has been verified. In normal and intermediate energies is feasible to use less noble as layers as the subgrade. The incorporation of the waste in layers of road pavements provide an alternative to conventionally used in paving aggregates, providing a proper disposal of tailings from scheelite, as well as environmental preservation

Caracterização de resíduos oriundos do beneficiamento do minério de ferro para uso em pavimentação

Mining in Brazil has a key role in economic and social development, contributing directly to improve the lives of the population. However, the mining activity even if done responsibly and with a proper study of waste management to reduce the impact of its effects, may cause harmful damage to the environment. Other forms of pollution are also caused due to mining activity. The visual pollution caused by the waste storage at open sky, in addition to the noise pollution caused by the excessive noise of the machines both in the extraction of ore, as in processing. An alternative way to lessen the environmental impacts caused by mining is the use of waste in layers that will compose the pavements along the highways. Thus, this work sets out to give a proper disposal of the wastes from the processing of iron ore, resulting from the mining activity of the group of mining Mhag Services and Mining S/A, in the mine of Bonito, located in Jucurutu, a town in the state of Rio Grande do Norte. The residues of the iron ore were stabilized with a granular soil from the city of Macaiba, also in the state of Rio Grande do Norte, which is being used in the duplication of the BR-304 referring to the entitled passage of Reta Tabajara. The present work was developed in three stages, being the first one divided by the chemical and mineralogical tests, by the tests of physical characterization and by the tests of paving for the residues of the iron ore. The second stage corresponds to the same tests being performed for granular soil. The third stage includes the essays abovementioned for three different mixtures of iron ore waste and granular soil, being they: 15% of iron-ore waste and 85% of granular soil, 25% of iron-ore waste and 75% of granular soil, 50% of iron-ore waste and 50% of granular soil. The technical feasibility of using waste from the iron ore beneficiation was checked, compressed in the intermediate energy and modified for use in base layers, sub-base, reinforcement subgrade and subgrade. The incorporation of the residues originating from the improvement of the iron ore in highways will provide an alternative to the use of aggregate conventionally used in the paving, besides preserving the environment.

Conception mécaniste-empirique des chaussées non revêtues

Dans le contexte où les routes non revêtues sont susceptibles de subir des charges importantes, une méthode rigoureuse pour la conception de ces chaussées basée sur des principes mécanistes-empiriques et sur le comportement mécanique des sols support est souhaitable. La conception mécaniste combinée à des lois d’endommagement permet l’optimisation des structures de chaussées non revêtues ainsi que la réduction des coûts de construction et d’entretien. Le but de ce projet est donc la mise au point d’une méthode de conception mécaniste-empirique adaptée aux chaussées non revêtues. Il a été question tout d’abord de mettre au point un code de calcul pour la détermination des contraintes et des déformations dans la chaussée. Ensuite, des lois d’endommagement empiriques pour les chaussées non revêtues ont été développées. Enfin, les méthodes de calcul ont permis la création d’abaques de conception. Le développement du code de calcul a consisté en une modélisation de la chaussée par un système élastique multi-couches. La modélisation a été faite en utilisant la transformation d’Odemark et les équations de Boussinesq pour le calcul des déformations sous la charge. L’élaboration des fonctions de transfert empiriques adaptées aux chaussées non revêtues a également été effectuée. Le développement des fonctions de transfert s’est fait en deux étapes. Tout d’abord, l’établissement de valeurs seuil d’orniérage considérant des niveaux jugés raisonnables de conditions fonctionnelle et structurale de la chaussée. Ensuite, le développement de critères de déformation admissible en associant les déformations théoriques calculées à l’aide du code de calcul à l’endommagement observé sur plusieurs routes en service. Les essais ont eu lieu sur des chaussées typiques reconstituées en laboratoire et soumises à un chargement répété par simulateur de charge. Les chaussées ont été instrumentées pour mesurer la déformation au sommet du sol d’infrastructure et les taux d’endommagements ont été mesurés au cours des essais.

GEOTECHNICAL AND ENVIRONMENTAL IMPACTS OF STEEL SLAG IN EMBANKMENTS

Steel slag is a byproduct of iron and steel production by the metallurgical industries. Annually, 21 million tons of steel slag is produced in the United States. Most of the slag is landfilled, which represents a significant economic loss and a waste of valuable land space. Steel slag has great potential for the construction of highway embankments; however, its use has been limited due to its high swelling potential and alkalinity. The swelling potential of steel slags may lead to deterioration of the structural stability of highways, and high alkalinity poses an environmental challenge as it affects the leaching behavior of trace metals. This study seeks a methodology that promotes the use of steel slag in highway embankments by minimizing these two main disadvantages. Accelerated swelling tests were conducted to evaluate the swelling behavior of pure steel slag and water treatment residual (WTR) treated steel slag, where WTR is an alum-rich by-product of drinking water treatment plants. Sequential batch tests and column leach tests, as well as two different numerical analyses, UMDSurf and WiscLEACH, were carried out to check the environmental suitability of the methods. Tests were conducted to study the effect of a common borrow fill material that encapsulated the slag in the embankment and the effects of two subgrade soils on the chemical properties of slag leachate. The results indicated that an increase in WTR content in the steel slag-WTR mixtures yields a decrease in pH and most of the leached metal concentrations, except aluminum. The change in the levels of pH, after passing through encapsulation and subgrade, depends on the natural pHs of materials.

Soft computing based parameter identification in pavements and geomechanical systems

Accurate estimation of road pavement geometry and layer material properties through the use of proper nondestructive testing and sensor technologies is essential for evaluating pavement’s structural condition and determining options for maintenance and rehabilitation. For these purposes, pavement deflection basins produced by the nondestructive Falling Weight Deflectometer (FWD) test data are commonly used. The nondestructive FWD test drops weights on the pavement to simulate traffic loads and measures the created pavement deflection basins. Backcalculation of pavement geometry and layer properties using FWD deflections is a difficult inverse problem, and the solution with conventional mathematical methods is often challenging due to the ill-posed nature of the problem. In this dissertation, a hybrid algorithm was developed to seek robust and fast solutions to this inverse problem. The algorithm is based on soft computing techniques, mainly Artificial Neural Networks (ANNs) and Genetic Algorithms (GAs) as well as the use of numerical analysis techniques to properly simulate the geomechanical system. A widely used pavement layered analysis program ILLI-PAVE was employed in the analyses of flexible pavements of various pavement types; including full-depth asphalt and conventional flexible pavements, were built on either lime stabilized soils or untreated subgrade. Nonlinear properties of the subgrade soil and the base course aggregate as transportation geomaterials were also considered. A computer program, Soft Computing Based System Identifier or SOFTSYS, was developed. In SOFTSYS, ANNs were used as surrogate models to provide faster solutions of the nonlinear finite element program ILLI-PAVE. The deflections obtained from FWD tests in the field were matched with the predictions obtained from the numerical simulations to develop SOFTSYS models. The solution to the inverse problem for multi-layered pavements is computationally hard to achieve and is often not feasible due to field variability and quality of the collected data. The primary difficulty in the analysis arises from the substantial increase in the degree of non-uniqueness of the mapping from the pavement layer parameters to the FWD deflections. The insensitivity of some layer properties lowered SOFTSYS model performances. Still, SOFTSYS models were shown to work effectively with the synthetic data obtained from ILLI-PAVE finite element solutions. In general, SOFTSYS solutions very closely matched the ILLI-PAVE mechanistic pavement analysis results. For SOFTSYS validation, field collected FWD data were successfully used to predict pavement layer thicknesses and layer moduli of in-service flexible pavements. Some of the very promising SOFTSYS results indicated average absolute errors on the order of 2%, 7%, and 4% for the Hot Mix Asphalt (HMA) thickness estimation of full-depth asphalt pavements, full-depth pavements on lime stabilized soils and conventional flexible pavements, respectively. The field validations of SOFTSYS data also produced meaningful results. The thickness data obtained from Ground Penetrating Radar testing matched reasonably well with predictions from SOFTSYS models. The differences observed in the HMA and lime stabilized soil layer thicknesses observed were attributed to deflection data variability from FWD tests. The backcalculated asphalt concrete layer thickness results matched better in the case of full-depth asphalt flexible pavements built on lime stabilized soils compared to conventional flexible pavements. Overall, SOFTSYS was capable of producing reliable thickness estimates despite the variability of field constructed asphalt layer thicknesses.

Analyse de profils de chaussées: Effet du gel saisonnier et de la dégradation du pergélisol

Des techniques adaptées aux contextes routiers sont nécessaires pour maintenir et réhabiliter des chaussées construites sur pergélisol ou en contexte de gel saisonnier. Plusieurs problématiques peuvent engendrer une augmentation des coûts de réparation et entretien, une diminution de la durée de vie des chaussées et des problèmes reliés à la sécurité des usagers de la route. L’objectif du projet consiste donc à élaborer un outil d’aide à la décision, qui contribuerait à localiser les zones sensibles au gel saisonnier et à la dégradation du pergélisol, à discerner les causes de dégradation des chaussées dues au gel saisonnier et à sélectionner les meilleures stratégies d’atténuation et de réfection à moindre coût. Le projet de recherche est divisé en deux volets distincts. Le premier volet traite des problématiques de gel de chaussées en contexte de gel saisonnier. Actuellement, il existe des méthodes de diagnostic qui permettent de détecter les endroits où un problème de gélivité est susceptible d’être présent. Par contre, ces méthodes ne permettent pas de discerner si le problème de gel est en profondeur ou en surface de la chaussée; en d’autres mots si le problème est lié à un soulèvement différentiel du sol ou à un soulèvement de fissures. De plus, les méthodes utilisées ne sont pas adaptées aux chaussées en contexte municipal. Selon les problématiques connues de certains sites, il a été possible de développer un abaque permettant de différencier si la problématique de gel se situe en surface ou en profondeur dans une chaussée. Puis, une analyse d’imagerie 3D a été réalisée pour complémenter l’abaque créé. À l’aide de cette technologie, une nouvelle méthode sera mise au point pour détecter des problématiques de gel grâce aux profils transversaux. Le deuxième volet porte sur les chaussées construites sur pergélisol. Les méthodes actuelles de détection de la dégradation du pergélisol sous les chaussées manquent de précision et ont besoin d’être raffinées, surtout dans le contexte actuel de réchauffement climatique. Pour ce faire, trois sites d’essais ont été étudiés sur l’Alaska Highway au Yukon. En fonction de différentes analyses telles que des analyses de profils longitudinaux, de la densité spectrale et de longueurs d’onde, des tendances ont été décelées pour caractériser l’instabilité du pergélisol.