Avaliação da erodibilidade pelo método Inderbitzen em solo não saturado da região de Bauru - SP

Pós-graduação em Engenharia Civil e Ambiental - FEB

Temperature Effects on Suction Measurement Using the Filter Paper Technique

This paper presents the results of an experimental study of thermal effects on filter paper calibration curves used to obtain the soil suction. When the temperature is significantly different from ambient values, it is essential to consider the influence of temperature on the filter paper calibration curves to obtain a reliable soil suction measurement. The calibration curve of Whatman No. 42 filter paper was determined at 10 degrees C, 25 degrees C, and 50 degrees C using the vapor equilibrium technique with sodium chloride solutions at different concentrations and the axis translation technique. The experimental results showed a major influence of temperature on the filter paper calibration curves. Using the obtained experimental data a calibration equation was proposed, taking into account the effect of temperature. The obtained calibration curves were then used to determine the soil water retention curve of kaolin clay, which showed lower retention capacity at higher temperatures.

Determinazione Sperimentale della curva di ritenzione idrica di alcuni terreni sabbiosi.

This thesis involves the evaluation of Soil Water Retention Curve using a new device purchased by BIGEA : HYPROP . Having studied and analyzed the characteristics that distinguish the partially saturated soils, I analyzed the silty - sandy soil samples taken in Granaglione ( BO ) with the HYPROP equipment. Subsequently the SWRC was realized using the HYPROP - FIT software. The obtained data were compared with those found in literature and they reflect the outcomes we expected . This confirms the valid HYPROP instrumentation .

O conceito de equilíbrio hidráulico e termodinâmico da água no solo aplicado ao estudo da curva de retenção e murchamento de plantas

Estimativas sobre alterações climáticas globais têm aumentando a demanda por estudos sobre propriedades dos solos relativamente secos e limitações impostas à absorção de água pelas plantas em condições de escassez hídrica. Neste estudo, fatores que influenciam a retenção da água no solo e o murchamento de plantas foram avaliados com base no conceito de equilíbrio da água no solo. Objetivou-se com este estudo: (i) avaliar a confiabilidade de medições do conteúdo de água no solo sob altas sucções matriciais em câmaras de pressão, usando como referência a técnica de ponto de orvalho (ii) avaliar as interações entre espécies de plantas e solos com diferentes classes texturais no ponto de murcha permanente (iii) investigar as relações entre equilíbrio hidráulico da água no solo e murchamento de plantas a partir do conceito de corte hidráulico. Para tanto, um experimento para avaliar a influência dos tipos de solos e espécies de plantas, no ponto de murcha permanente foi conduzido em casa de vegetação da Escola Superior de Agricultura \"Luiz de Queiroz\" da Universidade de São Paulo, Piracicaba, São Paulo. Avaliou-se o murchamento de plantas de girassol (Helianthus annuus L.), milho (Zea mays L.) e soja (Glycine max L.). Os solos utilizados no estudo foram coletados na camada superficial (0-10 cm) em quatro áreas, selecionadas com o objetivo de obter classes texturais contrastantes, localizadas no município de Piracicaba, São Paulo, Brasil. Sub-amostras foram utilizadas para determinação da distribuição do tamanho de partículas e atributos químicos. Amostras indeformadas foram coletadas para a determinação da curva de retenção da água no solo pela técnica de câmaras de pressão. Adicionalmente, amostras deformadas foram utilizadas para determinação das características de retenção da água no solo pela técnica do ponto de orvalho em altos valores de sucções matriciais. Os dados de retenção de água no solo foram ajustados a modelos empíricos para estimativas da sucção matricial e conteúdo de água relacionada à água em equilíbrio hidráulico (água residual). Foram observadas similaridades nas determinações das características de retenção da água no solo entre as técnicas de câmaras de pressão e ponto de orvalho, sugerindo a boa drenagem das amostras de solo em câmaras de pressão. Interações significativas foram observadas entre os tipos de solos e espécies de plantas no ponto de murcha permanente, indicando que o movimento de água no contínuo solo-planta-atmosfera foi dependente de resistências relacionadas tanto ao solo quanto às plantas. Ou seja, tanto à capacidade do solo em transportar água até raízes, quanto à habilidade das plantas em absorver a água transportada, assim como, aos processos de regulação de água que ocorrem nas plantas. A abordagem baseada no conteúdo de água residual para o intervalo de sucções matriciais de 0 a 15.000 hPa não foi adequada para ilustrar a condição de equilíbrio hidráulico da água no solo, definidos pelo corte hidráulico, e relações com as sucções matriciais em ocorre o murchamento de plantas.

Influência do tamanho da amostra na determinação da curva de retenção da água no solo

A curva de retenção da água no solo é um dos principais instrumentos para avaliar a qualidade física dos solos e possibilitar seu manejo adequado. Por meio da Teoria da Capilaridade vários equipamentos foram desenvolvidos para determinar a intensidade com que a água está retida ao solo, porém, pouco se tem dado atenção para verificar se os pressupostos para o real funcionamento da teoria estão sendo atendidos. Um aspecto refere-se ao tamanho da amostra utilizada para determinar a curva de retenção, de modo que haja continuidade dos feixes capilares na amostra e placa porosa. Desta forma, este trabalho propõe avaliar diferentes tamanhos de amostra indeformada para a determinação da curva de retenção. Para isso, coletaram-se amostras em anéis volumétricos cilíndricos de três tamanhos (altura) diferentes (T1 - 0,075 m; T2 - 0,05 m; T3 - 0,025 m;) e mesmo diâmetro interno (0,07 m), dos horizontes diagnósticos de um Latossolo e um Nitossolo em áreas experimentais da Escola Superior de Agricultura Luiz de Queiroz (Esalq/USP), Piracicaba - SP. Realizou-se a caracterização física destes solos, por meio da análise granulométrica, densidade do solo, densidade de partículas, porosidade total e teor de carbono orgânico. As curvas foram determinadas para cada tamanho de amostra, utilizando-se o Funil de Haines, para as tensões 0,5, 1, 4, 6 e 10 kPa, e a Câmara de Pressão de Richards para 33, 100 e 500 kPa. As curvas de retenção foram ajustadas pelo modelo utilizado por van Genuchten. Estimadas as curvas, avaliou-se a distribuição de poros do solo das amostras, determinando-se a curva de frequência acumulada de poros em função do logaritmo do raio e, depois pela diferenciação das equações de ajuste das curvas de retenção, a curva diferencial de frequência acumulada de poros. Os resultados mostram que o Latossolo, por ter textura arenosa no horizonte estudado, não apresentou diferença significativa nas curvas de retenção para os tamanhos das amostras estudadas. Verificou-se pouca modificação na distribuição dos poros deste solo, que possui teor elevado das frações areia fina e muito fina, e desenvolveram papel importante para a retenção de água. O Nitossolo, por sua vez, apresentou diferença significativa da curva obtida pela amostra de menor tamanho (T3), havendo maior retenção de água com a diminuição do tamanho da amostra. Devido a sua textura muito argilosa, o arranjo estrutural deste solo foi diferenciado ao se utilizar as amostras maiores, com provável interrupção e descontinuidade dos feixes capilares. Consequentemente, houve também alteração na distribuição dos poros, com redução dos mesoporos e aumento dos microporos. Desta forma, pode-se concluir que o tamanho da amostra influenciou a curva de retenção da água devido à complexidade estrutural do solo, que provavelmente é diferente nas amostras maiores por causa da continuidade dos feixes capilares, principalmente no Nitossolo. Em outras palavras, quanto menor o tamanho da amostra há menor diferenciação no arranjo de poros, ou seja, maior proximidade da real condição do solo e, assim, uma interpretação da retenção de água \"mais correta\" por meio da Teoria da Capilaridade.

Water retention and availability in soils of the State of Santa Catarina-Brazil: effect of textural classes, soil classes and lithology

The retention and availability of water in the soil vary according to the soil characteristics and determine plant growth. Thus, the aim of this study was to evaluate water retention and availability in the soils of the State of Santa Catarina, Brazil, according to the textural class, soil class and lithology. The surface and subsurface horizons of 44 profiles were sampled in different regions of the State and different cover crops to determine field capacity, permanent wilting point, available water content, particle size, and organic matter content. Water retention and availability between the horizons were compared in a mixed model, considering the textural classes, the soil classes and lithology as fixed factors and profiles as random factors. It may be concluded that water retention is greater in silty or clayey soils and that the organic matter content is higher, especially in Humic Cambisols, Nitisols and Ferralsol developed from igneous or sedimentary rocks. Water availability is greater in loam-textured soils, with high organic matter content, especially in soils of humic character. It is lower in the sandy texture class, especially in Arenosols formed from recent alluvial deposits or in gravelly soils derived from granite. The greater water availability in the surface horizons, with more organic matter than in the subsurface layers, illustrates the importance of organic matter for water retention and availability.

Changes in water availability in the soil due to tractor traffic

Frequent traffic of tractors in agricultural soils, promotes soil compaction and affects the flow and water availability. The aim of this research was to study the effect of compaction induced by tractor traffic on water availability in the soil under different traffic intensities on the same path (0, 1, 3, 6 and 10 passages), to two tractors with 3.3 and 2.6 ton of weights, over three different surface conditions. The study was conducted in an Andisol, representative soil of the study area. It was determined the behavior of the water retention curve, obtaining the gravitational water, available water and hygroscopic water, to 10 and 30 cm of depth. The hygroscopic water is the most prevalent with values ​​of up to 80% of the total water present in the soil. The water retention curves showed increases in the values ​​of field capacity and wilting point and behaviors "flattened" indicating a high sensitivity to the applied treatments, representative of compacted soils, which give the surfaces studied characteristics do not suitable for normal crop development.

Modeling plant transpiration under limited soil water: comparison of different plant and soil hydraulic parameterizations and preliminary implications for their use in land surface models

Accurate estimates of how soil water stress affects plant transpiration are crucial for reliable land surface model (LSM) predictions. Current LSMs generally use a water stress factor, β, dependent on soil moisture content, θ, that ranges linearly between β = 1 for unstressed vegetation and β = 0 when wilting point is reached. This paper explores the feasibility of replacing the current approach with equations that use soil water potential as their independent variable, or with a set of equations that involve hydraulic and chemical signaling, thereby ensuring feedbacks between the entire soil–root–xylem–leaf system. A comparison with the original linear θ-based water stress parameterization, and with its improved curvi-linear version, was conducted. Assessment of model suitability was focused on their ability to simulate the correct (as derived from experimental data) curve shape of relative transpiration versus fraction of transpirable soil water. We used model sensitivity analyses under progressive soil drying conditions, employing two commonly used approaches to calculate water retention and hydraulic conductivity curves. Furthermore, for each of these hydraulic parameterizations we used two different parameter sets, for 3 soil texture types; a total of 12 soil hydraulic permutations. Results showed that the resulting transpiration reduction functions (TRFs) varied considerably among the models. The fact that soil hydraulic conductivity played a major role in the model that involved hydraulic and chemical signaling led to unrealistic values of β, and hence TRF, for many soil hydraulic parameter sets. However, this model is much better equipped to simulate the behavior of different plant species. Based on these findings, we only recommend implementation of this approach into LSMs if great care with choice of soil hydraulic parameters is taken

Time stability of soil water storage measured by neutron probe and the effects of calibration procedures in a small watershed

The knowledge of soil water storage (SWS) of soil profiles is crucial for the adoption of vegetation restoration practices. With the aim of identifying representative sites to obtain the mean SWS of a watershed, a time stability analysis of neutron probe evaluations of SWS was performed by the means of relative differences and Spearman rank correlation coefficients. At the same time, the effects of different neutron probe calibration procedures were explored on time stability analysis. mean SWS estimation. and preservation of the spatial variability of SWS. The selected watershed, with deep gullies and undulating slopes which cover an area of 20 ha, is characterized by an Ust-Sandiic Entisol and an Aeolian sandy soil. The dominant vegetation species are bunge needlegrass (Stipa bungeana Trim) and korshinsk peashrub (Carugano Korshinskii kom.). From June 11, 2007 to July 23,2008, SWS of the top1 m soil layer was evaluated for 20 dates, based on neutron probe data of 12 sampling sites. Three calibration procedures were employed: type 1, most complete, with each site having its own linear calibration equation (TrE); type II. with TrE equations extended over the whole field: and type III, with one single linear calibration curve for the whole field (UnE) and also correcting its intercept based on site specific relative difference analysis (RdE) and on linear fitting of data (RcE), both maintaining the same slope. A strong time stability of SWS estimated by TrE equations was identified. Soil particle size and soil organic matter content were recognized as the influencing factors for spatial variability of SWS. Land use influenced neither the spatial variability nor the time stability of SWS. Time stability analysis identified one site to represent the mean SWS of the whole watershed with mean absolute percentage errors of less than 10%, therefore. this site can be used as a predictor for the mean SWS of the watershed. Some equations of type II were found to be unsatisfactory to yield reliable mean SWS values or in preserving the associated soil spatial variability. Hence, it is recommended to be cautious in extending calibration equations to other sites since they might not consider the field variability. For the equations with corrected intercept (type III), which consider the spatial variability of calibration in a different way in relation to TrE, it was found that they can yield satisfactory means and standard deviation of SWS, except for the RdE equations, which largely leveled off the SWS values in the watershed. Correlation analysis showed that the neutron probe calibration was linked to soil bulk density and to organic matter content. Therefore, spatial variability of soil properties should be taken into account during the process of neutron probe calibration. This study provides useful information on the mean SWS observation with a time stable site and on distinct neutron probe calibration procedures, and it should be extended to soil water management studies with neutron probes, e.g., the process of vegetation restoration in wider area and soil types of the Loess Plateau in China. (C) 2009 Elsevier B.V. All rights reserved.

Derivation of soil-specific streaming potential electrical parameters from hydrodynamic characteristics of partially saturated soils

Water movement in unsaturated soils gives rise to measurable electrical potential differences that are related to the flow direction and volumetric fluxes, as well as to the soil properties themselves. Laboratory and field data suggest that these so-called streaming potentials may be several orders of magnitudes larger than theoretical predictions that only consider the influence of the relative permeability and electrical conductivity on the self potential (SP) data. Recent work has improved predictions somewhat by considering how the volumetric excess charge in the pore space scales with the inverse of water saturation. We present a new theoretical approach that uses the flux-averaged excess charge, not the volumetric excess charge, to predict streaming potentials. We present relationships for how this effective excess charge varies with water saturation for typical soil properties using either the water retention or the relative permeability function. We find large differences between soil types and the predictions based on the relative permeability function display the best agreement with field data. The new relationships better explain laboratory data than previous work and allow us to predict the recorded magnitudes of the streaming potentials following a rainfall event in sandy loam, whereas previous models predict values that are three orders of magnitude too small. We suggest that the strong signals in unsaturated media can be used to gain information about fluxes (including very small ones related to film flow), but also to constrain the relative permeability function, the water retention curve, and the relative electrical conductivity function.

Short and long-term effects of tillage systems and nutrient sources on soil physical properties of a Southern Brazilian Hapludox

Soil tillage promotes changes in soil structure. The magnitude of the changes varies with the nature of the soil, tillage system and soil water content and decreases over time after tillage. The objective of this study was to evaluate short-term (one year period) and long-term (nine year period) effects of soil tillage and nutrient sources on some physical properties of a very clayey Hapludox. Five tillage systems were evaluated: no-till (NT), chisel plow + one secondary disking (CP), primary + two (secondary) diskings (CT), CT with burning of crop residues (CTb), and CT with removal of crop residues from the field (CTr), in combination with five nutrient sources: control without nutrient application (C); mineral fertilizers, according to technical recommendations for each crop (MF); 5 Mg ha-1 yr-1 of poultry litter (wetmatter) (PL); 60 m³ ha-1 yr-1 of cattle slurry (CS) and; 40 m³ ha-1 yr-1 of swine slurry (SS). Bulk density (BD), total porosity (TP), and parameters related to the water retention curve (macroporosity, mesoporosity and microporosity) were determined after nine years and at five sampling dates during the tenth year of the experiment. Soil physical properties were tillage and time-dependent. Tilled treatments increased total porosity and macroporosity, and reduced bulk density in the surface layer (0.00-0.05 m), but this effect decreased over time after tillage operations due to natural soil reconsolidation, since no external stress was applied in this period. Changes in pore size distribution were more pronounced in larger and medium pore diameter classes. The bulk density was greatest in intermediate layers in all tillage treatments (0.05-0.10 and 0.12-0.17 m) and decreased down to the deepest layer (0.27-0.32 m), indicating a more compacted layer around 0.05-0.20 m. Nutrient sources did not significantly affect soil physical and hydraulic properties studied.

Characterization of soil structure and porosity under long-term conventional tillage and no-tillage systems

Different management systems tend to modify soil structure and porosity over the years. The aim of this study was to study modifications in the morphostructure and porosity of dystroferric Red Latosol (Oxisol) under conventional tillage and no-tillage over a 31- year period. The study began with the description of soil profiles based on the cropping profile method, to identify the most compact structures, define sample collection points for physical and chemical analysis, and determine the water retention curve. A forest soil profile was described and used as reference. The results showed that, under conventional tillage, the microaggregate structure of the Oxisol was fragmented between 0 and 0.20 m, and compact (bulk density = 1.52 Mg m-3) in the sub-surface layer between 0.20 and 0.50 m. Under no-tillage, the structure became compacted (bulk density = 1.40 Mg m-3) between 0 and 0.60 m, but contained fissures and biopores. The volume of the class with a pore diameter of > 100 µm under no-tillage was limited, but practically non-existent in the conventional management system. On the other hand, the classes with a pore diameter of < 100 µm were not affected by the type of soil management system.

Pedotransfer functions related to spatial variability of water retention attributes for lowland soils

The estimation of non available soil variables through the knowledge of other related measured variables can be achieved through pedotransfer functions (PTF) mainly saving time and reducing cost. Great differences among soils, however, can yield non desirable results when applying this method. This study discusses the application of developed PTFs by several authors using a variety of soils of different characteristics, to evaluate soil water contents of two Brazilian lowland soils. Comparisons are made between PTF evaluated data and field measured data, using statistical and geostatistical tools, like mean error, root mean square error, semivariogram, cross-validation, and regression coefficient. The eight tested PTFs to evaluate gravimetric soil water contents (Ug) at the tensions of 33 kPa and 1,500 kPa presented a tendency to overestimate Ug 33 kPa and underestimate Ug1,500 kPa. The PTFs were ranked according to their performance and also with respect to their potential in describing the structure of the spatial variability of the set of measured values. Although none of the PTFs have changed the distribution pattern of the data, all resulted in mean and variance statistically different from those observed for all measured values. The PTFs that presented the best predictive values of Ug33 kPa and Ug1,500 kPa were not the same that had the best performance to reproduce the structure of spatial variability of these variables.

Water retention in a peatland with organic matter in different decomposition stages

Peatlands are ecosystems formed by successive pedogenetic processes, resulting in progressive accumulation of plant remains in the soil column under conditions that inhibit the activity of most microbial decomposers. In Diamantina, state of Minas Gerais, Brazil, a peatland is located at 1366 m asl, in a region with a quartz-rich lithology and characteristic wet grassland vegetation. For this study, the peat area was divided in 12 transects, from which a total of 90 soil samples were collected at a distance of 20 m from each other. The properties rubbed fiber content (RF), bulk density (Bd), mineral material (MM), organic matter (OM), moisture (Moi) and maximum water holding capacity (MWHC) were analyzed in all samples. From three selected profiles of this whole area, samples were collected every 27 cm from the soil surface down to a depth of 216 cm. In these samples, moisture was additionally determined at a pressure of 10 kPa (Moi10) or 1500 kPa (Moi1500), using Richards' extractor and soil organic matter was fractionated by standard procedures. The OM decomposition stage of this peat was found to increase with soil depth. Moi and MWHC were highest in layers with less advanced stages of OM decomposition. The humin levels were highest in layers in earlier stages of OM decomposition and with higher levels of water retention at MWHC and Moi10. Humic acid contents were higher in layers at an intermediate stage of decomposition of organic matter and with lowest levels of water retention at MWHC, Moi10 and Moi1500.